Felipe Balbi | 550a737 | 2008-07-24 12:27:36 +0300 | [diff] [blame] | 1 | /* |
| 2 | * Definitions for TUSB6010 USB 2.0 OTG Dual Role controller |
| 3 | * |
| 4 | * Copyright (C) 2006 Nokia Corporation |
| 5 | * Jarkko Nikula <jarkko.nikula@nokia.com> |
| 6 | * Tony Lindgren <tony@atomide.com> |
| 7 | * |
| 8 | * This program is free software; you can redistribute it and/or modify |
| 9 | * it under the terms of the GNU General Public License version 2 as |
| 10 | * published by the Free Software Foundation. |
| 11 | */ |
| 12 | |
| 13 | #ifndef __TUSB6010_H__ |
| 14 | #define __TUSB6010_H__ |
| 15 | |
| 16 | extern u8 tusb_get_revision(struct musb *musb); |
| 17 | |
| 18 | #ifdef CONFIG_USB_TUSB6010 |
| 19 | #define musb_in_tusb() 1 |
| 20 | #else |
| 21 | #define musb_in_tusb() 0 |
| 22 | #endif |
| 23 | |
| 24 | #ifdef CONFIG_USB_TUSB_OMAP_DMA |
| 25 | #define tusb_dma_omap() 1 |
| 26 | #else |
| 27 | #define tusb_dma_omap() 0 |
| 28 | #endif |
| 29 | |
| 30 | /* VLYNQ control register. 32-bit at offset 0x000 */ |
| 31 | #define TUSB_VLYNQ_CTRL 0x004 |
| 32 | |
| 33 | /* Mentor Graphics OTG core registers. 8,- 16- and 32-bit at offset 0x400 */ |
| 34 | #define TUSB_BASE_OFFSET 0x400 |
| 35 | |
| 36 | /* FIFO registers 32-bit at offset 0x600 */ |
| 37 | #define TUSB_FIFO_BASE 0x600 |
| 38 | |
| 39 | /* Device System & Control registers. 32-bit at offset 0x800 */ |
| 40 | #define TUSB_SYS_REG_BASE 0x800 |
| 41 | |
| 42 | #define TUSB_DEV_CONF (TUSB_SYS_REG_BASE + 0x000) |
| 43 | #define TUSB_DEV_CONF_USB_HOST_MODE (1 << 16) |
| 44 | #define TUSB_DEV_CONF_PROD_TEST_MODE (1 << 15) |
| 45 | #define TUSB_DEV_CONF_SOFT_ID (1 << 1) |
| 46 | #define TUSB_DEV_CONF_ID_SEL (1 << 0) |
| 47 | |
| 48 | #define TUSB_PHY_OTG_CTRL_ENABLE (TUSB_SYS_REG_BASE + 0x004) |
| 49 | #define TUSB_PHY_OTG_CTRL (TUSB_SYS_REG_BASE + 0x008) |
| 50 | #define TUSB_PHY_OTG_CTRL_WRPROTECT (0xa5 << 24) |
| 51 | #define TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP (1 << 23) |
| 52 | #define TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN (1 << 19) |
| 53 | #define TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN (1 << 18) |
| 54 | #define TUSB_PHY_OTG_CTRL_TESTM2 (1 << 17) |
| 55 | #define TUSB_PHY_OTG_CTRL_TESTM1 (1 << 16) |
| 56 | #define TUSB_PHY_OTG_CTRL_TESTM0 (1 << 15) |
| 57 | #define TUSB_PHY_OTG_CTRL_TX_DATA2 (1 << 14) |
| 58 | #define TUSB_PHY_OTG_CTRL_TX_GZ2 (1 << 13) |
| 59 | #define TUSB_PHY_OTG_CTRL_TX_ENABLE2 (1 << 12) |
| 60 | #define TUSB_PHY_OTG_CTRL_DM_PULLDOWN (1 << 11) |
| 61 | #define TUSB_PHY_OTG_CTRL_DP_PULLDOWN (1 << 10) |
| 62 | #define TUSB_PHY_OTG_CTRL_OSC_EN (1 << 9) |
| 63 | #define TUSB_PHY_OTG_CTRL_PHYREF_CLKSEL(v) (((v) & 3) << 7) |
| 64 | #define TUSB_PHY_OTG_CTRL_PD (1 << 6) |
| 65 | #define TUSB_PHY_OTG_CTRL_PLL_ON (1 << 5) |
| 66 | #define TUSB_PHY_OTG_CTRL_EXT_RPU (1 << 4) |
| 67 | #define TUSB_PHY_OTG_CTRL_PWR_GOOD (1 << 3) |
| 68 | #define TUSB_PHY_OTG_CTRL_RESET (1 << 2) |
| 69 | #define TUSB_PHY_OTG_CTRL_SUSPENDM (1 << 1) |
| 70 | #define TUSB_PHY_OTG_CTRL_CLK_MODE (1 << 0) |
| 71 | |
| 72 | /*OTG status register */ |
| 73 | #define TUSB_DEV_OTG_STAT (TUSB_SYS_REG_BASE + 0x00c) |
| 74 | #define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD (1 << 8) |
| 75 | #define TUSB_DEV_OTG_STAT_SESS_END (1 << 7) |
| 76 | #define TUSB_DEV_OTG_STAT_SESS_VALID (1 << 6) |
| 77 | #define TUSB_DEV_OTG_STAT_VBUS_VALID (1 << 5) |
| 78 | #define TUSB_DEV_OTG_STAT_VBUS_SENSE (1 << 4) |
| 79 | #define TUSB_DEV_OTG_STAT_ID_STATUS (1 << 3) |
| 80 | #define TUSB_DEV_OTG_STAT_HOST_DISCON (1 << 2) |
| 81 | #define TUSB_DEV_OTG_STAT_LINE_STATE (3 << 0) |
| 82 | #define TUSB_DEV_OTG_STAT_DP_ENABLE (1 << 1) |
| 83 | #define TUSB_DEV_OTG_STAT_DM_ENABLE (1 << 0) |
| 84 | |
| 85 | #define TUSB_DEV_OTG_TIMER (TUSB_SYS_REG_BASE + 0x010) |
| 86 | # define TUSB_DEV_OTG_TIMER_ENABLE (1 << 31) |
| 87 | # define TUSB_DEV_OTG_TIMER_VAL(v) ((v) & 0x07ffffff) |
| 88 | #define TUSB_PRCM_REV (TUSB_SYS_REG_BASE + 0x014) |
| 89 | |
| 90 | /* PRCM configuration register */ |
| 91 | #define TUSB_PRCM_CONF (TUSB_SYS_REG_BASE + 0x018) |
| 92 | #define TUSB_PRCM_CONF_SFW_CPEN (1 << 24) |
| 93 | #define TUSB_PRCM_CONF_SYS_CLKSEL(v) (((v) & 3) << 16) |
| 94 | |
| 95 | /* PRCM management register */ |
| 96 | #define TUSB_PRCM_MNGMT (TUSB_SYS_REG_BASE + 0x01c) |
| 97 | #define TUSB_PRCM_MNGMT_SRP_FIX_TIMER(v) (((v) & 0xf) << 25) |
| 98 | #define TUSB_PRCM_MNGMT_SRP_FIX_EN (1 << 24) |
| 99 | #define TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(v) (((v) & 0xf) << 20) |
| 100 | #define TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN (1 << 19) |
| 101 | #define TUSB_PRCM_MNGMT_DFT_CLK_DIS (1 << 18) |
| 102 | #define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS (1 << 17) |
| 103 | #define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10) |
| 104 | #define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9) |
| 105 | #define TUSB_PRCM_MNGMT_OTG_ID_PULLUP (1 << 8) |
| 106 | #define TUSB_PRCM_MNGMT_15_SW_EN (1 << 4) |
| 107 | #define TUSB_PRCM_MNGMT_33_SW_EN (1 << 3) |
| 108 | #define TUSB_PRCM_MNGMT_5V_CPEN (1 << 2) |
| 109 | #define TUSB_PRCM_MNGMT_PM_IDLE (1 << 1) |
| 110 | #define TUSB_PRCM_MNGMT_DEV_IDLE (1 << 0) |
| 111 | |
| 112 | /* Wake-up source clear and mask registers */ |
| 113 | #define TUSB_PRCM_WAKEUP_SOURCE (TUSB_SYS_REG_BASE + 0x020) |
| 114 | #define TUSB_PRCM_WAKEUP_CLEAR (TUSB_SYS_REG_BASE + 0x028) |
| 115 | #define TUSB_PRCM_WAKEUP_MASK (TUSB_SYS_REG_BASE + 0x02c) |
| 116 | #define TUSB_PRCM_WAKEUP_RESERVED_BITS (0xffffe << 13) |
| 117 | #define TUSB_PRCM_WGPIO_7 (1 << 12) |
| 118 | #define TUSB_PRCM_WGPIO_6 (1 << 11) |
| 119 | #define TUSB_PRCM_WGPIO_5 (1 << 10) |
| 120 | #define TUSB_PRCM_WGPIO_4 (1 << 9) |
| 121 | #define TUSB_PRCM_WGPIO_3 (1 << 8) |
| 122 | #define TUSB_PRCM_WGPIO_2 (1 << 7) |
| 123 | #define TUSB_PRCM_WGPIO_1 (1 << 6) |
| 124 | #define TUSB_PRCM_WGPIO_0 (1 << 5) |
| 125 | #define TUSB_PRCM_WHOSTDISCON (1 << 4) /* Host disconnect */ |
| 126 | #define TUSB_PRCM_WBUS (1 << 3) /* USB bus resume */ |
| 127 | #define TUSB_PRCM_WNORCS (1 << 2) /* NOR chip select */ |
| 128 | #define TUSB_PRCM_WVBUS (1 << 1) /* OTG PHY VBUS */ |
| 129 | #define TUSB_PRCM_WID (1 << 0) /* OTG PHY ID detect */ |
| 130 | |
| 131 | #define TUSB_PULLUP_1_CTRL (TUSB_SYS_REG_BASE + 0x030) |
| 132 | #define TUSB_PULLUP_2_CTRL (TUSB_SYS_REG_BASE + 0x034) |
| 133 | #define TUSB_INT_CTRL_REV (TUSB_SYS_REG_BASE + 0x038) |
| 134 | #define TUSB_INT_CTRL_CONF (TUSB_SYS_REG_BASE + 0x03c) |
| 135 | #define TUSB_USBIP_INT_SRC (TUSB_SYS_REG_BASE + 0x040) |
| 136 | #define TUSB_USBIP_INT_SET (TUSB_SYS_REG_BASE + 0x044) |
| 137 | #define TUSB_USBIP_INT_CLEAR (TUSB_SYS_REG_BASE + 0x048) |
| 138 | #define TUSB_USBIP_INT_MASK (TUSB_SYS_REG_BASE + 0x04c) |
| 139 | #define TUSB_DMA_INT_SRC (TUSB_SYS_REG_BASE + 0x050) |
| 140 | #define TUSB_DMA_INT_SET (TUSB_SYS_REG_BASE + 0x054) |
| 141 | #define TUSB_DMA_INT_CLEAR (TUSB_SYS_REG_BASE + 0x058) |
| 142 | #define TUSB_DMA_INT_MASK (TUSB_SYS_REG_BASE + 0x05c) |
| 143 | #define TUSB_GPIO_INT_SRC (TUSB_SYS_REG_BASE + 0x060) |
| 144 | #define TUSB_GPIO_INT_SET (TUSB_SYS_REG_BASE + 0x064) |
| 145 | #define TUSB_GPIO_INT_CLEAR (TUSB_SYS_REG_BASE + 0x068) |
| 146 | #define TUSB_GPIO_INT_MASK (TUSB_SYS_REG_BASE + 0x06c) |
| 147 | |
| 148 | /* NOR flash interrupt source registers */ |
| 149 | #define TUSB_INT_SRC (TUSB_SYS_REG_BASE + 0x070) |
| 150 | #define TUSB_INT_SRC_SET (TUSB_SYS_REG_BASE + 0x074) |
| 151 | #define TUSB_INT_SRC_CLEAR (TUSB_SYS_REG_BASE + 0x078) |
| 152 | #define TUSB_INT_MASK (TUSB_SYS_REG_BASE + 0x07c) |
| 153 | #define TUSB_INT_SRC_TXRX_DMA_DONE (1 << 24) |
| 154 | #define TUSB_INT_SRC_USB_IP_CORE (1 << 17) |
| 155 | #define TUSB_INT_SRC_OTG_TIMEOUT (1 << 16) |
| 156 | #define TUSB_INT_SRC_VBUS_SENSE_CHNG (1 << 15) |
| 157 | #define TUSB_INT_SRC_ID_STATUS_CHNG (1 << 14) |
| 158 | #define TUSB_INT_SRC_DEV_WAKEUP (1 << 13) |
| 159 | #define TUSB_INT_SRC_DEV_READY (1 << 12) |
| 160 | #define TUSB_INT_SRC_USB_IP_TX (1 << 9) |
| 161 | #define TUSB_INT_SRC_USB_IP_RX (1 << 8) |
| 162 | #define TUSB_INT_SRC_USB_IP_VBUS_ERR (1 << 7) |
| 163 | #define TUSB_INT_SRC_USB_IP_VBUS_REQ (1 << 6) |
| 164 | #define TUSB_INT_SRC_USB_IP_DISCON (1 << 5) |
| 165 | #define TUSB_INT_SRC_USB_IP_CONN (1 << 4) |
| 166 | #define TUSB_INT_SRC_USB_IP_SOF (1 << 3) |
| 167 | #define TUSB_INT_SRC_USB_IP_RST_BABBLE (1 << 2) |
| 168 | #define TUSB_INT_SRC_USB_IP_RESUME (1 << 1) |
| 169 | #define TUSB_INT_SRC_USB_IP_SUSPEND (1 << 0) |
| 170 | |
| 171 | /* NOR flash interrupt registers reserved bits. Must be written as 0 */ |
| 172 | #define TUSB_INT_MASK_RESERVED_17 (0x3fff << 17) |
| 173 | #define TUSB_INT_MASK_RESERVED_13 (1 << 13) |
| 174 | #define TUSB_INT_MASK_RESERVED_8 (0xf << 8) |
| 175 | #define TUSB_INT_SRC_RESERVED_26 (0x1f << 26) |
| 176 | #define TUSB_INT_SRC_RESERVED_18 (0x3f << 18) |
| 177 | #define TUSB_INT_SRC_RESERVED_10 (0x03 << 10) |
| 178 | |
| 179 | /* Reserved bits for NOR flash interrupt mask and clear register */ |
| 180 | #define TUSB_INT_MASK_RESERVED_BITS (TUSB_INT_MASK_RESERVED_17 | \ |
| 181 | TUSB_INT_MASK_RESERVED_13 | \ |
| 182 | TUSB_INT_MASK_RESERVED_8) |
| 183 | |
| 184 | /* Reserved bits for NOR flash interrupt status register */ |
| 185 | #define TUSB_INT_SRC_RESERVED_BITS (TUSB_INT_SRC_RESERVED_26 | \ |
| 186 | TUSB_INT_SRC_RESERVED_18 | \ |
| 187 | TUSB_INT_SRC_RESERVED_10) |
| 188 | |
| 189 | #define TUSB_GPIO_REV (TUSB_SYS_REG_BASE + 0x080) |
| 190 | #define TUSB_GPIO_CONF (TUSB_SYS_REG_BASE + 0x084) |
| 191 | #define TUSB_DMA_CTRL_REV (TUSB_SYS_REG_BASE + 0x100) |
| 192 | #define TUSB_DMA_REQ_CONF (TUSB_SYS_REG_BASE + 0x104) |
| 193 | #define TUSB_EP0_CONF (TUSB_SYS_REG_BASE + 0x108) |
| 194 | #define TUSB_DMA_EP_MAP (TUSB_SYS_REG_BASE + 0x148) |
| 195 | |
| 196 | /* Offsets from each ep base register */ |
| 197 | #define TUSB_EP_TX_OFFSET 0x10c /* EP_IN in docs */ |
| 198 | #define TUSB_EP_RX_OFFSET 0x14c /* EP_OUT in docs */ |
| 199 | #define TUSB_EP_MAX_PACKET_SIZE_OFFSET 0x188 |
| 200 | |
| 201 | #define TUSB_WAIT_COUNT (TUSB_SYS_REG_BASE + 0x1c8) |
| 202 | #define TUSB_SCRATCH_PAD (TUSB_SYS_REG_BASE + 0x1c4) |
| 203 | #define TUSB_PROD_TEST_RESET (TUSB_SYS_REG_BASE + 0x1d8) |
| 204 | |
| 205 | /* Device System & Control register bitfields */ |
| 206 | #define TUSB_INT_CTRL_CONF_INT_RELCYC(v) (((v) & 0x7) << 18) |
| 207 | #define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17) |
| 208 | #define TUSB_INT_CTRL_CONF_INT_MODE (1 << 16) |
| 209 | #define TUSB_GPIO_CONF_DMAREQ(v) (((v) & 0x3f) << 24) |
| 210 | #define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26) |
| 211 | #define TUSB_DMA_REQ_CONF_DMA_REQ_EN(v) (((v) & 0x3f) << 20) |
| 212 | #define TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(v) (((v) & 0xf) << 16) |
| 213 | #define TUSB_EP0_CONFIG_SW_EN (1 << 8) |
| 214 | #define TUSB_EP0_CONFIG_DIR_TX (1 << 7) |
| 215 | #define TUSB_EP0_CONFIG_XFR_SIZE(v) ((v) & 0x7f) |
| 216 | #define TUSB_EP_CONFIG_SW_EN (1 << 31) |
| 217 | #define TUSB_EP_CONFIG_XFR_SIZE(v) ((v) & 0x7fffffff) |
| 218 | #define TUSB_PROD_TEST_RESET_VAL 0xa596 |
| 219 | #define TUSB_EP_FIFO(ep) (TUSB_FIFO_BASE + (ep) * 0x20) |
| 220 | |
| 221 | #define TUSB_DIDR1_LO (TUSB_SYS_REG_BASE + 0x1f8) |
| 222 | #define TUSB_DIDR1_HI (TUSB_SYS_REG_BASE + 0x1fc) |
| 223 | #define TUSB_DIDR1_HI_CHIP_REV(v) (((v) >> 17) & 0xf) |
| 224 | #define TUSB_DIDR1_HI_REV_20 0 |
| 225 | #define TUSB_DIDR1_HI_REV_30 1 |
| 226 | #define TUSB_DIDR1_HI_REV_31 2 |
| 227 | |
| 228 | #define TUSB_REV_10 0x10 |
| 229 | #define TUSB_REV_20 0x20 |
| 230 | #define TUSB_REV_30 0x30 |
| 231 | #define TUSB_REV_31 0x31 |
| 232 | |
Felipe Balbi | 550a737 | 2008-07-24 12:27:36 +0300 | [diff] [blame] | 233 | #endif /* __TUSB6010_H__ */ |