Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | # |
| 2 | # Video configuration |
| 3 | # |
| 4 | |
| 5 | menu "Graphics support" |
Martin Schwidefsky | e25df12 | 2007-05-10 15:45:57 +0200 | [diff] [blame] | 6 | depends on HAS_IOMEM |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 7 | |
Nicolas Ferre | 0912e53 | 2009-06-23 16:30:56 +0200 | [diff] [blame] | 8 | config HAVE_FB_ATMEL |
| 9 | bool |
| 10 | |
Randy Dunlap | 179b025 | 2007-10-16 01:29:39 -0700 | [diff] [blame] | 11 | source "drivers/char/agp/Kconfig" |
| 12 | |
Benjamin Herrenschmidt | deb2d2e | 2009-08-11 15:52:06 +1000 | [diff] [blame] | 13 | source "drivers/gpu/vga/Kconfig" |
| 14 | |
Dave Airlie | c0e0920 | 2008-05-29 10:09:59 +1000 | [diff] [blame] | 15 | source "drivers/gpu/drm/Kconfig" |
Antonino A. Daplas | ba70710 | 2006-06-26 00:26:37 -0700 | [diff] [blame] | 16 | |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 17 | config VGASTATE |
| 18 | tristate |
| 19 | default n |
| 20 | |
Luming Yu | 23b0f01 | 2007-05-09 21:07:05 +0800 | [diff] [blame] | 21 | config VIDEO_OUTPUT_CONTROL |
| 22 | tristate "Lowlevel video output switch controls" |
Luming Yu | 23b0f01 | 2007-05-09 21:07:05 +0800 | [diff] [blame] | 23 | help |
| 24 | This framework adds support for low-level control of the video |
| 25 | output switch. |
| 26 | |
Randy Dunlap | 179b025 | 2007-10-16 01:29:39 -0700 | [diff] [blame] | 27 | menuconfig FB |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 28 | tristate "Support for frame buffer devices" |
| 29 | ---help--- |
| 30 | The frame buffer device provides an abstraction for the graphics |
| 31 | hardware. It represents the frame buffer of some video hardware and |
| 32 | allows application software to access the graphics hardware through |
| 33 | a well-defined interface, so the software doesn't need to know |
| 34 | anything about the low-level (hardware register) stuff. |
| 35 | |
| 36 | Frame buffer devices work identically across the different |
| 37 | architectures supported by Linux and make the implementation of |
| 38 | application programs easier and more portable; at this point, an X |
| 39 | server exists which uses the frame buffer device exclusively. |
| 40 | On several non-X86 architectures, the frame buffer device is the |
| 41 | only way to use the graphics hardware. |
| 42 | |
| 43 | The device is accessed through special device nodes, usually located |
| 44 | in the /dev directory, i.e. /dev/fb*. |
| 45 | |
| 46 | You need an utility program called fbset to make full use of frame |
| 47 | buffer devices. Please read <file:Documentation/fb/framebuffer.txt> |
| 48 | and the Framebuffer-HOWTO at |
Alex Buell | 248ae0d | 2009-01-29 14:25:16 -0800 | [diff] [blame] | 49 | <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.2.html> for more |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 50 | information. |
| 51 | |
| 52 | Say Y here and to the driver for your graphics board below if you |
| 53 | are compiling a kernel for a non-x86 architecture. |
| 54 | |
| 55 | If you are compiling for the x86 architecture, you can say Y if you |
| 56 | want to play with it, but it is not essential. Please note that |
| 57 | running graphical applications that directly touch the hardware |
| 58 | (e.g. an accelerated X server) and that are not frame buffer |
| 59 | device-aware may cause unexpected results. If unsure, say N. |
| 60 | |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 61 | config FIRMWARE_EDID |
| 62 | bool "Enable firmware EDID" |
| 63 | depends on FB |
| 64 | default n |
| 65 | ---help--- |
| 66 | This enables access to the EDID transferred from the firmware. |
| 67 | On the i386, this is from the Video BIOS. Enable this if DDC/I2C |
| 68 | transfers do not work for your driver and if you are using |
| 69 | nvidiafb, i810fb or savagefb. |
| 70 | |
| 71 | In general, choosing Y for this option is safe. If you |
| 72 | experience extremely long delays while booting before you get |
| 73 | something on your display, try setting this to N. Matrox cards in |
| 74 | combination with certain motherboards and monitors are known to |
| 75 | suffer from this problem. |
| 76 | |
Dennis Munsie | fc5891c | 2006-10-03 01:14:42 -0700 | [diff] [blame] | 77 | config FB_DDC |
| 78 | tristate |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 79 | depends on FB |
| 80 | select I2C_ALGOBIT |
| 81 | select I2C |
Dennis Munsie | fc5891c | 2006-10-03 01:14:42 -0700 | [diff] [blame] | 82 | default n |
| 83 | |
Michal Januszewski | 4d31a2b | 2008-10-15 22:03:51 -0700 | [diff] [blame] | 84 | config FB_BOOT_VESA_SUPPORT |
| 85 | bool |
| 86 | depends on FB |
| 87 | default n |
| 88 | ---help--- |
| 89 | If true, at least one selected framebuffer driver can take advantage |
| 90 | of VESA video modes set at an early boot stage via the vga= parameter. |
| 91 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 92 | config FB_CFB_FILLRECT |
| 93 | tristate |
| 94 | depends on FB |
| 95 | default n |
| 96 | ---help--- |
| 97 | Include the cfb_fillrect function for generic software rectangle |
| 98 | filling. This is used by drivers that don't provide their own |
| 99 | (accelerated) version. |
| 100 | |
| 101 | config FB_CFB_COPYAREA |
| 102 | tristate |
| 103 | depends on FB |
| 104 | default n |
| 105 | ---help--- |
| 106 | Include the cfb_copyarea function for generic software area copying. |
| 107 | This is used by drivers that don't provide their own (accelerated) |
| 108 | version. |
| 109 | |
| 110 | config FB_CFB_IMAGEBLIT |
| 111 | tristate |
| 112 | depends on FB |
| 113 | default n |
| 114 | ---help--- |
| 115 | Include the cfb_imageblit function for generic software image |
| 116 | blitting. This is used by drivers that don't provide their own |
| 117 | (accelerated) version. |
| 118 | |
Pavel Pisa | 779121e | 2007-10-16 01:29:21 -0700 | [diff] [blame] | 119 | config FB_CFB_REV_PIXELS_IN_BYTE |
| 120 | bool |
| 121 | depends on FB |
| 122 | default n |
| 123 | ---help--- |
| 124 | Allow generic frame-buffer functions to work on displays with 1, 2 |
| 125 | and 4 bits per pixel depths which has opposite order of pixels in |
| 126 | byte order to bytes in long order. |
| 127 | |
Antonino A. Daplas | 68648ed | 2007-05-08 00:38:57 -0700 | [diff] [blame] | 128 | config FB_SYS_FILLRECT |
| 129 | tristate |
| 130 | depends on FB |
| 131 | default n |
| 132 | ---help--- |
| 133 | Include the sys_fillrect function for generic software rectangle |
| 134 | filling. This is used by drivers that don't provide their own |
| 135 | (accelerated) version and the framebuffer is in system RAM. |
| 136 | |
| 137 | config FB_SYS_COPYAREA |
| 138 | tristate |
| 139 | depends on FB |
| 140 | default n |
| 141 | ---help--- |
| 142 | Include the sys_copyarea function for generic software area copying. |
| 143 | This is used by drivers that don't provide their own (accelerated) |
| 144 | version and the framebuffer is in system RAM. |
| 145 | |
| 146 | config FB_SYS_IMAGEBLIT |
| 147 | tristate |
| 148 | depends on FB |
| 149 | default n |
| 150 | ---help--- |
| 151 | Include the sys_imageblit function for generic software image |
| 152 | blitting. This is used by drivers that don't provide their own |
| 153 | (accelerated) version and the framebuffer is in system RAM. |
| 154 | |
Anton Vorontsov | e4c690e | 2008-04-28 02:14:49 -0700 | [diff] [blame] | 155 | menuconfig FB_FOREIGN_ENDIAN |
| 156 | bool "Framebuffer foreign endianness support" |
| 157 | depends on FB |
| 158 | ---help--- |
| 159 | This menu will let you enable support for the framebuffers with |
| 160 | non-native endianness (e.g. Little-Endian framebuffer on a |
| 161 | Big-Endian machine). Most probably you don't have such hardware, |
| 162 | so it's safe to say "n" here. |
| 163 | |
| 164 | choice |
| 165 | prompt "Choice endianness support" |
| 166 | depends on FB_FOREIGN_ENDIAN |
| 167 | |
| 168 | config FB_BOTH_ENDIAN |
| 169 | bool "Support for Big- and Little-Endian framebuffers" |
| 170 | |
| 171 | config FB_BIG_ENDIAN |
| 172 | bool "Support for Big-Endian framebuffers only" |
| 173 | |
| 174 | config FB_LITTLE_ENDIAN |
| 175 | bool "Support for Little-Endian framebuffers only" |
| 176 | |
| 177 | endchoice |
| 178 | |
Antonino A. Daplas | 09aaf26 | 2007-05-08 00:39:03 -0700 | [diff] [blame] | 179 | config FB_SYS_FOPS |
| 180 | tristate |
| 181 | depends on FB |
| 182 | default n |
| 183 | |
Jaya Kumar | 60b59be | 2007-05-08 00:37:37 -0700 | [diff] [blame] | 184 | config FB_DEFERRED_IO |
| 185 | bool |
| 186 | depends on FB |
Jaya Kumar | 60b59be | 2007-05-08 00:37:37 -0700 | [diff] [blame] | 187 | |
Jaya Kumar | 0e27aa3 | 2008-04-28 02:15:40 -0700 | [diff] [blame] | 188 | config FB_HECUBA |
| 189 | tristate |
| 190 | depends on FB |
| 191 | depends on FB_DEFERRED_IO |
| 192 | |
Ondrej Zajicek | a268422 | 2007-02-12 00:54:49 -0800 | [diff] [blame] | 193 | config FB_SVGALIB |
| 194 | tristate |
| 195 | depends on FB |
| 196 | default n |
| 197 | ---help--- |
| 198 | Common utility functions useful to fbdev drivers of VGA-based |
| 199 | cards. |
| 200 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 201 | config FB_MACMODES |
| 202 | tristate |
| 203 | depends on FB |
| 204 | default n |
| 205 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 206 | config FB_BACKLIGHT |
Michael Hanselmann | 4b75599 | 2006-07-30 03:04:19 -0700 | [diff] [blame] | 207 | bool |
| 208 | depends on FB |
| 209 | select BACKLIGHT_LCD_SUPPORT |
| 210 | select BACKLIGHT_CLASS_DEVICE |
| 211 | default n |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 212 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 213 | config FB_MODE_HELPERS |
| 214 | bool "Enable Video Mode Handling Helpers" |
| 215 | depends on FB |
| 216 | default n |
| 217 | ---help--- |
| 218 | This enables functions for handling video modes using the |
| 219 | Generalized Timing Formula and the EDID parser. A few drivers rely |
| 220 | on this feature such as the radeonfb, rivafb, and the i810fb. If |
| 221 | your driver does not take advantage of this feature, choosing Y will |
| 222 | just increase the kernel size by about 5K. |
| 223 | |
| 224 | config FB_TILEBLITTING |
| 225 | bool "Enable Tile Blitting Support" |
| 226 | depends on FB |
| 227 | default n |
| 228 | ---help--- |
| 229 | This enables tile blitting. Tile blitting is a drawing technique |
| 230 | where the screen is divided into rectangular sections (tiles), whereas |
| 231 | the standard blitting divides the screen into pixels. Because the |
| 232 | default drawing element is a tile, drawing functions will be passed |
| 233 | parameters in terms of number of tiles instead of number of pixels. |
| 234 | For example, to draw a single character, instead of using bitmaps, |
| 235 | an index to an array of bitmaps will be used. To clear or move a |
| 236 | rectangular section of a screen, the rectangle will be described in |
| 237 | terms of number of tiles in the x- and y-axis. |
| 238 | |
| 239 | This is particularly important to one driver, matroxfb. If |
| 240 | unsure, say N. |
| 241 | |
Miguel Ojeda | 10ccaf4 | 2007-04-23 14:41:09 -0700 | [diff] [blame] | 242 | comment "Frame buffer hardware drivers" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 243 | depends on FB |
| 244 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 245 | config FB_CIRRUS |
| 246 | tristate "Cirrus Logic support" |
| 247 | depends on FB && (ZORRO || PCI) |
| 248 | select FB_CFB_FILLRECT |
| 249 | select FB_CFB_COPYAREA |
| 250 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 251 | ---help--- |
| 252 | This enables support for Cirrus Logic GD542x/543x based boards on |
| 253 | Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum. |
| 254 | |
| 255 | If you have a PCI-based system, this enables support for these |
| 256 | chips: GD-543x, GD-544x, GD-5480. |
| 257 | |
| 258 | Please read the file <file:Documentation/fb/cirrusfb.txt>. |
| 259 | |
| 260 | Say N unless you have such a graphics board or plan to get one |
| 261 | before you next recompile the kernel. |
| 262 | |
| 263 | config FB_PM2 |
| 264 | tristate "Permedia2 support" |
| 265 | depends on FB && ((AMIGA && BROKEN) || PCI) |
| 266 | select FB_CFB_FILLRECT |
| 267 | select FB_CFB_COPYAREA |
| 268 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 269 | help |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 270 | This is the frame buffer device driver for cards based on |
| 271 | the 3D Labs Permedia, Permedia 2 and Permedia 2V chips. |
| 272 | The driver was tested on the following cards: |
| 273 | Diamond FireGL 1000 PRO AGP |
| 274 | ELSA Gloria Synergy PCI |
| 275 | Appian Jeronimo PRO (both heads) PCI |
| 276 | 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI |
| 277 | Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC |
| 278 | ASK Graphic Blaster Exxtreme AGP |
| 279 | |
| 280 | To compile this driver as a module, choose M here: the |
| 281 | module will be called pm2fb. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 282 | |
| 283 | config FB_PM2_FIFO_DISCONNECT |
| 284 | bool "enable FIFO disconnect feature" |
| 285 | depends on FB_PM2 && PCI |
| 286 | help |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 287 | Support the Permedia2 FIFO disconnect feature. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 288 | |
| 289 | config FB_ARMCLCD |
| 290 | tristate "ARM PrimeCell PL110 support" |
| 291 | depends on FB && ARM && ARM_AMBA |
| 292 | select FB_CFB_FILLRECT |
| 293 | select FB_CFB_COPYAREA |
| 294 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 295 | help |
| 296 | This framebuffer device driver is for the ARM PrimeCell PL110 |
| 297 | Colour LCD controller. ARM PrimeCells provide the building |
| 298 | blocks for System on a Chip devices. |
| 299 | |
| 300 | If you want to compile this as a module (=code which can be |
| 301 | inserted into and removed from the running kernel), say M |
Alexander E. Patrakov | 39f5fb3 | 2007-03-16 18:28:43 +0500 | [diff] [blame] | 302 | here and read <file:Documentation/kbuild/modules.txt>. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 303 | will be called amba-clcd. |
| 304 | |
Marc Singer | 903e2bb | 2006-05-16 11:41:30 +0100 | [diff] [blame] | 305 | choice |
| 306 | |
| 307 | depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X) |
| 308 | prompt "LCD Panel" |
| 309 | default FB_ARMCLCD_SHARP_LQ035Q7DB02 |
| 310 | |
| 311 | config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT |
| 312 | bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC" |
| 313 | help |
| 314 | This is an implementation of the Sharp LQ035Q7DB02, a 3.5" |
Matt LaPlante | cab0089 | 2006-10-03 22:36:44 +0200 | [diff] [blame] | 315 | color QVGA, HRTFT panel. The LogicPD device includes |
Marc Singer | 903e2bb | 2006-05-16 11:41:30 +0100 | [diff] [blame] | 316 | an integrated HRTFT controller IC. |
| 317 | The native resolution is 240x320. |
| 318 | |
| 319 | config FB_ARMCLCD_SHARP_LQ057Q3DC02 |
| 320 | bool "LogicPD LCD 5.7\" QVGA" |
| 321 | help |
| 322 | This is an implementation of the Sharp LQ057Q3DC02, a 5.7" |
| 323 | color QVGA, TFT panel. The LogicPD device includes an |
| 324 | The native resolution is 320x240. |
| 325 | |
| 326 | config FB_ARMCLCD_SHARP_LQ64D343 |
| 327 | bool "LogicPD LCD 6.4\" VGA" |
| 328 | help |
| 329 | This is an implementation of the Sharp LQ64D343, a 6.4" |
| 330 | color VGA, TFT panel. The LogicPD device includes an |
| 331 | The native resolution is 640x480. |
| 332 | |
| 333 | config FB_ARMCLCD_SHARP_LQ10D368 |
| 334 | bool "LogicPD LCD 10.4\" VGA" |
| 335 | help |
| 336 | This is an implementation of the Sharp LQ10D368, a 10.4" |
| 337 | color VGA, TFT panel. The LogicPD device includes an |
| 338 | The native resolution is 640x480. |
| 339 | |
| 340 | |
| 341 | config FB_ARMCLCD_SHARP_LQ121S1DG41 |
| 342 | bool "LogicPD LCD 12.1\" SVGA" |
| 343 | help |
| 344 | This is an implementation of the Sharp LQ121S1DG41, a 12.1" |
| 345 | color SVGA, TFT panel. The LogicPD device includes an |
| 346 | The native resolution is 800x600. |
| 347 | |
| 348 | This panel requires a clock rate may be an integer fraction |
| 349 | of the base LCDCLK frequency. The driver will select the |
| 350 | highest frequency available that is lower than the maximum |
| 351 | allowed. The panel may flicker if the clock rate is |
| 352 | slower than the recommended minimum. |
| 353 | |
| 354 | config FB_ARMCLCD_AUO_A070VW01_WIDE |
| 355 | bool "AU Optronics A070VW01 LCD 7.0\" WIDE" |
| 356 | help |
| 357 | This is an implementation of the AU Optronics, a 7.0" |
| 358 | WIDE Color. The native resolution is 234x480. |
| 359 | |
| 360 | config FB_ARMCLCD_HITACHI |
| 361 | bool "Hitachi Wide Screen 800x480" |
| 362 | help |
| 363 | This is an implementation of the Hitachi 800x480. |
| 364 | |
| 365 | endchoice |
| 366 | |
| 367 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 368 | config FB_ACORN |
| 369 | bool "Acorn VIDC support" |
Russell King | 635f025 | 2008-10-28 09:43:54 +0000 | [diff] [blame] | 370 | depends on (FB = y) && ARM && ARCH_ACORN |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 371 | select FB_CFB_FILLRECT |
| 372 | select FB_CFB_COPYAREA |
| 373 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 374 | help |
| 375 | This is the frame buffer device driver for the Acorn VIDC graphics |
| 376 | hardware found in Acorn RISC PCs and other ARM-based machines. If |
| 377 | unsure, say N. |
| 378 | |
| 379 | config FB_CLPS711X |
| 380 | bool "CLPS711X LCD support" |
| 381 | depends on (FB = y) && ARM && ARCH_CLPS711X |
| 382 | select FB_CFB_FILLRECT |
| 383 | select FB_CFB_COPYAREA |
| 384 | select FB_CFB_IMAGEBLIT |
Randy.Dunlap | e65c085 | 2005-11-07 01:00:28 -0800 | [diff] [blame] | 385 | help |
| 386 | Say Y to enable the Framebuffer driver for the CLPS7111 and |
| 387 | EP7212 processors. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 388 | |
| 389 | config FB_SA1100 |
| 390 | bool "SA-1100 LCD support" |
| 391 | depends on (FB = y) && ARM && ARCH_SA1100 |
| 392 | select FB_CFB_FILLRECT |
| 393 | select FB_CFB_COPYAREA |
| 394 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 395 | help |
| 396 | This is a framebuffer device for the SA-1100 LCD Controller. |
| 397 | See <http://www.linux-fbdev.org/> for information on framebuffer |
| 398 | devices. |
| 399 | |
| 400 | If you plan to use the LCD display with your SA-1100 system, say |
| 401 | Y here. |
| 402 | |
Sascha Hauer | 7c2f891c | 2005-05-01 08:59:24 -0700 | [diff] [blame] | 403 | config FB_IMX |
| 404 | tristate "Motorola i.MX LCD support" |
Sascha Hauer | 8c8fdbc | 2009-04-01 12:40:15 +0200 | [diff] [blame] | 405 | depends on FB && (ARCH_MX1 || ARCH_MX2) |
Sascha Hauer | 7c2f891c | 2005-05-01 08:59:24 -0700 | [diff] [blame] | 406 | select FB_CFB_FILLRECT |
| 407 | select FB_CFB_COPYAREA |
| 408 | select FB_CFB_IMAGEBLIT |
Sascha Hauer | 7c2f891c | 2005-05-01 08:59:24 -0700 | [diff] [blame] | 409 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 410 | config FB_CYBER2000 |
| 411 | tristate "CyberPro 2000/2010/5000 support" |
| 412 | depends on FB && PCI && (BROKEN || !SPARC64) |
| 413 | select FB_CFB_FILLRECT |
| 414 | select FB_CFB_COPYAREA |
| 415 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 416 | help |
| 417 | This enables support for the Integraphics CyberPro 20x0 and 5000 |
| 418 | VGA chips used in the Rebel.com Netwinder and other machines. |
| 419 | Say Y if you have a NetWinder or a graphics card containing this |
| 420 | device, otherwise say N. |
| 421 | |
| 422 | config FB_APOLLO |
| 423 | bool |
| 424 | depends on (FB = y) && APOLLO |
| 425 | default y |
| 426 | select FB_CFB_FILLRECT |
| 427 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 428 | |
| 429 | config FB_Q40 |
| 430 | bool |
| 431 | depends on (FB = y) && Q40 |
| 432 | default y |
| 433 | select FB_CFB_FILLRECT |
| 434 | select FB_CFB_COPYAREA |
| 435 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 436 | |
| 437 | config FB_AMIGA |
| 438 | tristate "Amiga native chipset support" |
| 439 | depends on FB && AMIGA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 440 | help |
| 441 | This is the frame buffer device driver for the builtin graphics |
| 442 | chipset found in Amigas. |
| 443 | |
| 444 | To compile this driver as a module, choose M here: the |
| 445 | module will be called amifb. |
| 446 | |
| 447 | config FB_AMIGA_OCS |
| 448 | bool "Amiga OCS chipset support" |
| 449 | depends on FB_AMIGA |
| 450 | help |
| 451 | This enables support for the original Agnus and Denise video chips, |
| 452 | found in the Amiga 1000 and most A500's and A2000's. If you intend |
| 453 | to run Linux on any of these systems, say Y; otherwise say N. |
| 454 | |
| 455 | config FB_AMIGA_ECS |
| 456 | bool "Amiga ECS chipset support" |
| 457 | depends on FB_AMIGA |
| 458 | help |
| 459 | This enables support for the Enhanced Chip Set, found in later |
| 460 | A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If |
| 461 | you intend to run Linux on any of these systems, say Y; otherwise |
| 462 | say N. |
| 463 | |
| 464 | config FB_AMIGA_AGA |
| 465 | bool "Amiga AGA chipset support" |
| 466 | depends on FB_AMIGA |
| 467 | help |
| 468 | This enables support for the Advanced Graphics Architecture (also |
| 469 | known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T |
| 470 | and CD32. If you intend to run Linux on any of these systems, say Y; |
| 471 | otherwise say N. |
| 472 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 473 | config FB_FM2 |
| 474 | bool "Amiga FrameMaster II/Rainbow II support" |
| 475 | depends on (FB = y) && ZORRO |
| 476 | select FB_CFB_FILLRECT |
| 477 | select FB_CFB_COPYAREA |
| 478 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 479 | help |
| 480 | This is the frame buffer device driver for the Amiga FrameMaster |
| 481 | card from BSC (exhibited 1992 but not shipped as a CBM product). |
| 482 | |
Jaya Kumar | 1154ea7 | 2005-06-21 17:17:04 -0700 | [diff] [blame] | 483 | config FB_ARC |
| 484 | tristate "Arc Monochrome LCD board support" |
| 485 | depends on FB && X86 |
Antonino A. Daplas | 922e6f9 | 2007-05-08 00:38:58 -0700 | [diff] [blame] | 486 | select FB_SYS_FILLRECT |
| 487 | select FB_SYS_COPYAREA |
| 488 | select FB_SYS_IMAGEBLIT |
Antonino A. Daplas | d9a05f1 | 2007-05-08 00:39:04 -0700 | [diff] [blame] | 489 | select FB_SYS_FOPS |
Jaya Kumar | 1154ea7 | 2005-06-21 17:17:04 -0700 | [diff] [blame] | 490 | help |
| 491 | This enables support for the Arc Monochrome LCD board. The board |
| 492 | is based on the KS-108 lcd controller and is typically a matrix |
| 493 | of 2*n chips. This driver was tested with a 128x64 panel. This |
| 494 | driver supports it for use with x86 SBCs through a 16 bit GPIO |
Matt LaPlante | 0950960 | 2006-10-03 22:31:37 +0200 | [diff] [blame] | 495 | interface (8 bit data, 8 bit control). If you anticipate using |
Jaya Kumar | 1154ea7 | 2005-06-21 17:17:04 -0700 | [diff] [blame] | 496 | this driver, say Y or M; otherwise say N. You must specify the |
| 497 | GPIO IO address to be used for setting control and data. |
| 498 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 499 | config FB_ATARI |
| 500 | bool "Atari native chipset support" |
Michael Schmitz | a100501 | 2007-05-01 22:32:39 +0200 | [diff] [blame] | 501 | depends on (FB = y) && ATARI |
| 502 | select FB_CFB_FILLRECT |
| 503 | select FB_CFB_COPYAREA |
| 504 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 505 | help |
| 506 | This is the frame buffer device driver for the builtin graphics |
| 507 | chipset found in Ataris. |
| 508 | |
| 509 | config FB_OF |
| 510 | bool "Open Firmware frame buffer device support" |
Stephen Rothwell | bed5927 | 2007-03-04 17:04:44 +1100 | [diff] [blame] | 511 | depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 512 | select FB_CFB_FILLRECT |
| 513 | select FB_CFB_COPYAREA |
| 514 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 515 | select FB_MACMODES |
| 516 | help |
| 517 | Say Y if you want support with Open Firmware for your graphics |
| 518 | board. |
| 519 | |
| 520 | config FB_CONTROL |
| 521 | bool "Apple \"control\" display support" |
Olaf Hering | a04b61d | 2006-07-30 03:03:52 -0700 | [diff] [blame] | 522 | depends on (FB = y) && PPC_PMAC && PPC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 523 | select FB_CFB_FILLRECT |
| 524 | select FB_CFB_COPYAREA |
| 525 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 526 | select FB_MACMODES |
| 527 | help |
| 528 | This driver supports a frame buffer for the graphics adapter in the |
| 529 | Power Macintosh 7300 and others. |
| 530 | |
| 531 | config FB_PLATINUM |
| 532 | bool "Apple \"platinum\" display support" |
Olaf Hering | a04b61d | 2006-07-30 03:03:52 -0700 | [diff] [blame] | 533 | depends on (FB = y) && PPC_PMAC && PPC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 534 | select FB_CFB_FILLRECT |
| 535 | select FB_CFB_COPYAREA |
| 536 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 537 | select FB_MACMODES |
| 538 | help |
| 539 | This driver supports a frame buffer for the "platinum" graphics |
| 540 | adapter in some Power Macintoshes. |
| 541 | |
| 542 | config FB_VALKYRIE |
| 543 | bool "Apple \"valkyrie\" display support" |
Olaf Hering | a04b61d | 2006-07-30 03:03:52 -0700 | [diff] [blame] | 544 | depends on (FB = y) && (MAC || (PPC_PMAC && PPC32)) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 545 | select FB_CFB_FILLRECT |
| 546 | select FB_CFB_COPYAREA |
| 547 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 548 | select FB_MACMODES |
| 549 | help |
| 550 | This driver supports a frame buffer for the "valkyrie" graphics |
| 551 | adapter in some Power Macintoshes. |
| 552 | |
| 553 | config FB_CT65550 |
| 554 | bool "Chips 65550 display support" |
Randy Dunlap | 0f8c0234 | 2007-11-14 16:58:45 -0800 | [diff] [blame] | 555 | depends on (FB = y) && PPC32 && PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 556 | select FB_CFB_FILLRECT |
| 557 | select FB_CFB_COPYAREA |
| 558 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 559 | help |
| 560 | This is the frame buffer device driver for the Chips & Technologies |
| 561 | 65550 graphics chip in PowerBooks. |
| 562 | |
| 563 | config FB_ASILIANT |
Randy.Dunlap | e65c085 | 2005-11-07 01:00:28 -0800 | [diff] [blame] | 564 | bool "Asiliant (Chips) 69000 display support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 565 | depends on (FB = y) && PCI |
| 566 | select FB_CFB_FILLRECT |
| 567 | select FB_CFB_COPYAREA |
| 568 | select FB_CFB_IMAGEBLIT |
Antonino A. Daplas | 4de0b1e | 2006-04-27 18:40:47 -0700 | [diff] [blame] | 569 | help |
| 570 | This is the frame buffer device driver for the Asiliant 69030 chipset |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 571 | |
| 572 | config FB_IMSTT |
| 573 | bool "IMS Twin Turbo display support" |
| 574 | depends on (FB = y) && PCI |
| 575 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 576 | select FB_MACMODES if PPC |
| 577 | help |
| 578 | The IMS Twin Turbo is a PCI-based frame buffer card bundled with |
| 579 | many Macintosh and compatible computers. |
| 580 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 581 | config FB_VGA16 |
| 582 | tristate "VGA 16-color graphics support" |
| 583 | depends on FB && (X86 || PPC) |
| 584 | select FB_CFB_FILLRECT |
| 585 | select FB_CFB_COPYAREA |
| 586 | select FB_CFB_IMAGEBLIT |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 587 | select VGASTATE |
Antonino A. Daplas | d60d2d8 | 2007-05-08 00:39:12 -0700 | [diff] [blame] | 588 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 589 | help |
| 590 | This is the frame buffer device driver for VGA 16 color graphic |
| 591 | cards. Say Y if you have such a card. |
| 592 | |
| 593 | To compile this driver as a module, choose M here: the |
| 594 | module will be called vga16fb. |
| 595 | |
Michael Hennerich | e9fa7c4 | 2007-10-16 01:29:38 -0700 | [diff] [blame] | 596 | config FB_BF54X_LQ043 |
| 597 | tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)" |
Mike Frysinger | e7a05aa | 2008-04-28 02:15:47 -0700 | [diff] [blame] | 598 | depends on FB && (BF54x) && !BF542 |
Michael Hennerich | e9fa7c4 | 2007-10-16 01:29:38 -0700 | [diff] [blame] | 599 | select FB_CFB_FILLRECT |
| 600 | select FB_CFB_COPYAREA |
| 601 | select FB_CFB_IMAGEBLIT |
| 602 | help |
| 603 | This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD |
| 604 | |
Michael Hennerich | 99eeed47a | 2008-03-10 11:44:04 -0700 | [diff] [blame] | 605 | config FB_BFIN_T350MCQB |
| 606 | tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)" |
| 607 | depends on FB && BLACKFIN |
| 608 | select BFIN_GPTIMERS |
| 609 | select FB_CFB_FILLRECT |
| 610 | select FB_CFB_COPYAREA |
| 611 | select FB_CFB_IMAGEBLIT |
| 612 | help |
| 613 | This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD |
| 614 | This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI |
| 615 | It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK. |
| 616 | |
| 617 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 618 | config FB_STI |
| 619 | tristate "HP STI frame buffer device support" |
| 620 | depends on FB && PARISC |
| 621 | select FB_CFB_FILLRECT |
| 622 | select FB_CFB_COPYAREA |
| 623 | select FB_CFB_IMAGEBLIT |
Alexander Beregalov | 17085a9 | 2009-04-03 13:33:32 +0000 | [diff] [blame] | 624 | select STI_CONSOLE |
| 625 | select VT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 626 | default y |
| 627 | ---help--- |
| 628 | STI refers to the HP "Standard Text Interface" which is a set of |
| 629 | BIOS routines contained in a ROM chip in HP PA-RISC based machines. |
| 630 | Enabling this option will implement the linux framebuffer device |
| 631 | using calls to the STI BIOS routines for initialisation. |
| 632 | |
| 633 | If you enable this option, you will get a planar framebuffer device |
| 634 | /dev/fb which will work on the most common HP graphic cards of the |
| 635 | NGLE family, including the artist chips (in the 7xx and Bxxx series), |
| 636 | HCRX, HCRX24, CRX, CRX24 and VisEG series. |
| 637 | |
| 638 | It is safe to enable this option, so you should probably say "Y". |
| 639 | |
| 640 | config FB_MAC |
| 641 | bool "Generic Macintosh display support" |
| 642 | depends on (FB = y) && MAC |
| 643 | select FB_CFB_FILLRECT |
| 644 | select FB_CFB_COPYAREA |
| 645 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 646 | select FB_MACMODES |
| 647 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 648 | config FB_HP300 |
| 649 | bool |
Geert Uytterhoeven | ad7e484 | 2008-05-18 20:47:09 +0200 | [diff] [blame] | 650 | depends on (FB = y) && DIO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 651 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 652 | default y |
| 653 | |
| 654 | config FB_TGA |
Maciej W. Rozycki | 86c6f7d | 2007-05-08 00:37:48 -0700 | [diff] [blame] | 655 | tristate "TGA/SFB+ framebuffer support" |
| 656 | depends on FB && (ALPHA || TC) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 657 | select FB_CFB_FILLRECT |
| 658 | select FB_CFB_COPYAREA |
| 659 | select FB_CFB_IMAGEBLIT |
Akinobu Mita | 1c66768 | 2006-12-08 02:36:26 -0800 | [diff] [blame] | 660 | select BITREVERSE |
Maciej W. Rozycki | 86c6f7d | 2007-05-08 00:37:48 -0700 | [diff] [blame] | 661 | ---help--- |
| 662 | This is the frame buffer device driver for generic TGA and SFB+ |
| 663 | graphic cards. These include DEC ZLXp-E1, -E2 and -E3 PCI cards, |
| 664 | also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3 |
| 665 | TURBOchannel cards, also known as PMAGD-A, -B and -C. |
| 666 | |
| 667 | Due to hardware limitations ZLX-E2 and E3 cards are not supported |
| 668 | for DECstation 5000/200 systems. Additionally due to firmware |
| 669 | limitations these cards may cause troubles with booting DECstation |
| 670 | 5000/240 and /260 systems, but are fully supported under Linux if |
| 671 | you manage to get it going. ;-) |
| 672 | |
| 673 | Say Y if you have one of those. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 674 | |
Michal Januszewski | 8bdb3a2 | 2007-10-16 01:28:26 -0700 | [diff] [blame] | 675 | config FB_UVESA |
| 676 | tristate "Userspace VESA VGA graphics support" |
| 677 | depends on FB && CONNECTOR |
| 678 | select FB_CFB_FILLRECT |
| 679 | select FB_CFB_COPYAREA |
| 680 | select FB_CFB_IMAGEBLIT |
| 681 | select FB_MODE_HELPERS |
| 682 | help |
| 683 | This is the frame buffer driver for generic VBE 2.0 compliant |
| 684 | graphic cards. It can also take advantage of VBE 3.0 features, |
| 685 | such as refresh rate adjustment. |
| 686 | |
| 687 | This driver generally provides more features than vesafb but |
| 688 | requires a userspace helper application called 'v86d'. See |
| 689 | <file:Documentation/fb/uvesafb.txt> for more information. |
| 690 | |
| 691 | If unsure, say N. |
| 692 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 693 | config FB_VESA |
| 694 | bool "VESA VGA graphics support" |
Brian Gerst | 0d078f6 | 2005-10-30 14:59:20 -0800 | [diff] [blame] | 695 | depends on (FB = y) && X86 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 696 | select FB_CFB_FILLRECT |
| 697 | select FB_CFB_COPYAREA |
| 698 | select FB_CFB_IMAGEBLIT |
Michal Januszewski | 4d31a2b | 2008-10-15 22:03:51 -0700 | [diff] [blame] | 699 | select FB_BOOT_VESA_SUPPORT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 700 | help |
| 701 | This is the frame buffer device driver for generic VESA 2.0 |
| 702 | compliant graphic cards. The older VESA 1.2 cards are not supported. |
| 703 | You will get a boot time penguin logo at no additional cost. Please |
| 704 | read <file:Documentation/fb/vesafb.txt>. If unsure, say Y. |
| 705 | |
Huang, Ying | 7c83172 | 2007-11-28 16:21:55 -0800 | [diff] [blame] | 706 | config FB_EFI |
| 707 | bool "EFI-based Framebuffer Support" |
Edgar Hucek | b64ef8a | 2006-08-13 23:24:16 -0700 | [diff] [blame] | 708 | depends on (FB = y) && X86 && EFI |
Edgar Hucek | 90b4f9a | 2006-06-26 00:26:59 -0700 | [diff] [blame] | 709 | select FB_CFB_FILLRECT |
| 710 | select FB_CFB_COPYAREA |
| 711 | select FB_CFB_IMAGEBLIT |
| 712 | help |
Peter Jones | 7c08c9a | 2008-10-15 22:03:43 -0700 | [diff] [blame] | 713 | This is the EFI frame buffer device driver. If the firmware on |
| 714 | your platform is EFI 1.10 or UEFI 2.0, select Y to add support for |
| 715 | using the EFI framebuffer as your console. |
Edgar Hucek | 90b4f9a | 2006-06-26 00:26:59 -0700 | [diff] [blame] | 716 | |
Jaya Kumar | 0e27aa3 | 2008-04-28 02:15:40 -0700 | [diff] [blame] | 717 | config FB_N411 |
| 718 | tristate "N411 Apollo/Hecuba devkit support" |
Jaya Kumar | aad09e5 | 2007-05-08 00:37:43 -0700 | [diff] [blame] | 719 | depends on FB && X86 && MMU |
Antonino A. Daplas | d677493 | 2007-05-08 00:39:00 -0700 | [diff] [blame] | 720 | select FB_SYS_FILLRECT |
| 721 | select FB_SYS_COPYAREA |
| 722 | select FB_SYS_IMAGEBLIT |
Antonino A. Daplas | 28d4564 | 2007-05-08 00:39:06 -0700 | [diff] [blame] | 723 | select FB_SYS_FOPS |
Jaya Kumar | aad09e5 | 2007-05-08 00:37:43 -0700 | [diff] [blame] | 724 | select FB_DEFERRED_IO |
Jaya Kumar | 0e27aa3 | 2008-04-28 02:15:40 -0700 | [diff] [blame] | 725 | select FB_HECUBA |
Jaya Kumar | aad09e5 | 2007-05-08 00:37:43 -0700 | [diff] [blame] | 726 | help |
Jaya Kumar | 0e27aa3 | 2008-04-28 02:15:40 -0700 | [diff] [blame] | 727 | This enables support for the Apollo display controller in its |
| 728 | Hecuba form using the n411 devkit. |
Jaya Kumar | aad09e5 | 2007-05-08 00:37:43 -0700 | [diff] [blame] | 729 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 730 | config FB_HGA |
| 731 | tristate "Hercules mono graphics support" |
| 732 | depends on FB && X86 |
| 733 | select FB_CFB_FILLRECT |
| 734 | select FB_CFB_COPYAREA |
| 735 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 736 | help |
| 737 | Say Y here if you have a Hercules mono graphics card. |
| 738 | |
| 739 | To compile this driver as a module, choose M here: the |
| 740 | module will be called hgafb. |
| 741 | |
| 742 | As this card technology is 15 years old, most people will answer N |
| 743 | here. |
| 744 | |
| 745 | config FB_HGA_ACCEL |
| 746 | bool "Hercules mono Acceleration functions (EXPERIMENTAL)" |
| 747 | depends on FB_HGA && EXPERIMENTAL |
| 748 | ---help--- |
| 749 | This will compile the Hercules mono graphics with |
| 750 | acceleration functions. |
| 751 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 752 | config FB_SGIVW |
| 753 | tristate "SGI Visual Workstation framebuffer support" |
| 754 | depends on FB && X86_VISWS |
| 755 | select FB_CFB_FILLRECT |
| 756 | select FB_CFB_COPYAREA |
| 757 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 758 | help |
| 759 | SGI Visual Workstation support for framebuffer graphics. |
| 760 | |
| 761 | config FB_GBE |
| 762 | bool "SGI Graphics Backend frame buffer support" |
| 763 | depends on (FB = y) && (SGI_IP32 || X86_VISWS) |
| 764 | select FB_CFB_FILLRECT |
| 765 | select FB_CFB_COPYAREA |
| 766 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 767 | help |
| 768 | This is the frame buffer device driver for SGI Graphics Backend. |
| 769 | This chip is used in SGI O2 and Visual Workstation 320/540. |
| 770 | |
| 771 | config FB_GBE_MEM |
| 772 | int "Video memory size in MB" |
| 773 | depends on FB_GBE |
Martin Michlmayr | 80c410d | 2006-02-24 13:04:16 -0800 | [diff] [blame] | 774 | default 4 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 775 | help |
| 776 | This is the amount of memory reserved for the framebuffer, |
| 777 | which can be any value between 1MB and 8MB. |
| 778 | |
Mark Fortescue | 1a57198 | 2005-11-29 19:34:44 -0800 | [diff] [blame] | 779 | config FB_SBUS |
| 780 | bool "SBUS and UPA framebuffers" |
Adrian Bunk | 0b57ee9 | 2005-12-22 21:03:47 -0800 | [diff] [blame] | 781 | depends on (FB = y) && SPARC |
Mark Fortescue | 1a57198 | 2005-11-29 19:34:44 -0800 | [diff] [blame] | 782 | help |
| 783 | Say Y if you want support for SBUS or UPA based frame buffer device. |
| 784 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 785 | config FB_BW2 |
| 786 | bool "BWtwo support" |
Adrian Bunk | e019630 | 2007-02-12 00:54:50 -0800 | [diff] [blame] | 787 | depends on (FB = y) && (SPARC && FB_SBUS) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 788 | select FB_CFB_FILLRECT |
| 789 | select FB_CFB_COPYAREA |
| 790 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 791 | help |
| 792 | This is the frame buffer device driver for the BWtwo frame buffer. |
| 793 | |
| 794 | config FB_CG3 |
| 795 | bool "CGthree support" |
Adrian Bunk | e019630 | 2007-02-12 00:54:50 -0800 | [diff] [blame] | 796 | depends on (FB = y) && (SPARC && FB_SBUS) |
Mark Fortescue | 1a57198 | 2005-11-29 19:34:44 -0800 | [diff] [blame] | 797 | select FB_CFB_FILLRECT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 798 | select FB_CFB_COPYAREA |
| 799 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 800 | help |
| 801 | This is the frame buffer device driver for the CGthree frame buffer. |
| 802 | |
| 803 | config FB_CG6 |
| 804 | bool "CGsix (GX,TurboGX) support" |
Adrian Bunk | e019630 | 2007-02-12 00:54:50 -0800 | [diff] [blame] | 805 | depends on (FB = y) && (SPARC && FB_SBUS) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 806 | select FB_CFB_COPYAREA |
| 807 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 808 | help |
| 809 | This is the frame buffer device driver for the CGsix (GX, TurboGX) |
| 810 | frame buffer. |
| 811 | |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 812 | config FB_FFB |
| 813 | bool "Creator/Creator3D/Elite3D support" |
| 814 | depends on FB_SBUS && SPARC64 |
| 815 | select FB_CFB_COPYAREA |
| 816 | select FB_CFB_IMAGEBLIT |
| 817 | help |
| 818 | This is the frame buffer device driver for the Creator, Creator3D, |
| 819 | and Elite3D graphics boards. |
| 820 | |
| 821 | config FB_TCX |
| 822 | bool "TCX (SS4/SS5 only) support" |
| 823 | depends on FB_SBUS |
| 824 | select FB_CFB_FILLRECT |
| 825 | select FB_CFB_COPYAREA |
| 826 | select FB_CFB_IMAGEBLIT |
| 827 | help |
| 828 | This is the frame buffer device driver for the TCX 24/8bit frame |
| 829 | buffer. |
| 830 | |
| 831 | config FB_CG14 |
| 832 | bool "CGfourteen (SX) support" |
| 833 | depends on FB_SBUS |
| 834 | select FB_CFB_FILLRECT |
| 835 | select FB_CFB_COPYAREA |
| 836 | select FB_CFB_IMAGEBLIT |
| 837 | help |
| 838 | This is the frame buffer device driver for the CGfourteen frame |
| 839 | buffer on Desktop SPARCsystems with the SX graphics option. |
| 840 | |
| 841 | config FB_P9100 |
| 842 | bool "P9100 (Sparcbook 3 only) support" |
| 843 | depends on FB_SBUS |
| 844 | select FB_CFB_FILLRECT |
| 845 | select FB_CFB_COPYAREA |
| 846 | select FB_CFB_IMAGEBLIT |
| 847 | help |
| 848 | This is the frame buffer device driver for the P9100 card |
| 849 | supported on Sparcbook 3 machines. |
| 850 | |
| 851 | config FB_LEO |
| 852 | bool "Leo (ZX) support" |
| 853 | depends on FB_SBUS |
| 854 | select FB_CFB_FILLRECT |
| 855 | select FB_CFB_COPYAREA |
| 856 | select FB_CFB_IMAGEBLIT |
| 857 | help |
| 858 | This is the frame buffer device driver for the SBUS-based Sun ZX |
| 859 | (leo) frame buffer cards. |
| 860 | |
| 861 | config FB_IGA |
| 862 | bool "IGA 168x display support" |
David S. Miller | e11a6c2 | 2007-06-03 17:35:24 -0700 | [diff] [blame] | 863 | depends on (FB = y) && SPARC32 |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 864 | select FB_CFB_FILLRECT |
| 865 | select FB_CFB_COPYAREA |
| 866 | select FB_CFB_IMAGEBLIT |
| 867 | help |
| 868 | This is the framebuffer device for the INTERGRAPHICS 1680 and |
| 869 | successor frame buffer cards. |
| 870 | |
| 871 | config FB_XVR500 |
| 872 | bool "Sun XVR-500 3DLABS Wildcat support" |
David S. Miller | e11a6c2 | 2007-06-03 17:35:24 -0700 | [diff] [blame] | 873 | depends on (FB = y) && PCI && SPARC64 |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 874 | select FB_CFB_FILLRECT |
| 875 | select FB_CFB_COPYAREA |
| 876 | select FB_CFB_IMAGEBLIT |
| 877 | help |
| 878 | This is the framebuffer device for the Sun XVR-500 and similar |
| 879 | graphics cards based upon the 3DLABS Wildcat chipset. The driver |
Matt LaPlante | 01dd2fb | 2007-10-20 01:34:40 +0200 | [diff] [blame] | 880 | only works on sparc64 systems where the system firmware has |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 881 | mostly initialized the card already. It is treated as a |
| 882 | completely dumb framebuffer device. |
| 883 | |
| 884 | config FB_XVR2500 |
| 885 | bool "Sun XVR-2500 3DLABS Wildcat support" |
David S. Miller | e11a6c2 | 2007-06-03 17:35:24 -0700 | [diff] [blame] | 886 | depends on (FB = y) && PCI && SPARC64 |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 887 | select FB_CFB_FILLRECT |
| 888 | select FB_CFB_COPYAREA |
| 889 | select FB_CFB_IMAGEBLIT |
| 890 | help |
| 891 | This is the framebuffer device for the Sun XVR-2500 and similar |
| 892 | graphics cards based upon the 3DLABS Wildcat chipset. The driver |
Matt LaPlante | 01dd2fb | 2007-10-20 01:34:40 +0200 | [diff] [blame] | 893 | only works on sparc64 systems where the system firmware has |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 894 | mostly initialized the card already. It is treated as a |
| 895 | completely dumb framebuffer device. |
| 896 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 897 | config FB_PVR2 |
| 898 | tristate "NEC PowerVR 2 display support" |
| 899 | depends on FB && SH_DREAMCAST |
| 900 | select FB_CFB_FILLRECT |
| 901 | select FB_CFB_COPYAREA |
| 902 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 903 | ---help--- |
| 904 | Say Y here if you have a PowerVR 2 card in your box. If you plan to |
| 905 | run linux on your Dreamcast, you will have to say Y here. |
| 906 | This driver may or may not work on other PowerVR 2 cards, but is |
| 907 | totally untested. Use at your own risk. If unsure, say N. |
| 908 | |
| 909 | To compile this driver as a module, choose M here: the |
| 910 | module will be called pvr2fb. |
| 911 | |
| 912 | You can pass several parameters to the driver at boot time or at |
| 913 | module load time. The parameters look like "video=pvr2:XXX", where |
| 914 | the meaning of XXX can be found at the end of the main source file |
| 915 | (<file:drivers/video/pvr2fb.c>). Please see the file |
| 916 | <file:Documentation/fb/pvr2fb.txt>. |
| 917 | |
| 918 | config FB_EPSON1355 |
| 919 | bool "Epson 1355 framebuffer support" |
Paul Mundt | 1a3f288 | 2007-07-17 04:05:48 -0700 | [diff] [blame] | 920 | depends on (FB = y) && ARCH_CEIVA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 921 | select FB_CFB_FILLRECT |
| 922 | select FB_CFB_COPYAREA |
| 923 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 924 | help |
| 925 | Build in support for the SED1355 Epson Research Embedded RAMDAC |
| 926 | LCD/CRT Controller (since redesignated as the S1D13505) as a |
| 927 | framebuffer. Product specs at |
| 928 | <http://www.erd.epson.com/vdc/html/products.htm>. |
| 929 | |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 930 | config FB_S1D13XXX |
| 931 | tristate "Epson S1D13XXX framebuffer support" |
| 932 | depends on FB |
| 933 | select FB_CFB_FILLRECT |
| 934 | select FB_CFB_COPYAREA |
| 935 | select FB_CFB_IMAGEBLIT |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 936 | help |
| 937 | Support for S1D13XXX framebuffer device family (currently only |
| 938 | working with S1D13806). Product specs at |
| 939 | <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm> |
| 940 | |
Nicolas Ferre | 1434058 | 2007-05-10 22:23:26 -0700 | [diff] [blame] | 941 | config FB_ATMEL |
| 942 | tristate "AT91/AT32 LCD Controller support" |
Nicolas Ferre | 0912e53 | 2009-06-23 16:30:56 +0200 | [diff] [blame] | 943 | depends on FB && HAVE_FB_ATMEL |
Nicolas Ferre | 1434058 | 2007-05-10 22:23:26 -0700 | [diff] [blame] | 944 | select FB_CFB_FILLRECT |
| 945 | select FB_CFB_COPYAREA |
| 946 | select FB_CFB_IMAGEBLIT |
| 947 | help |
| 948 | This enables support for the AT91/AT32 LCD Controller. |
| 949 | |
| 950 | config FB_INTSRAM |
| 951 | bool "Frame Buffer in internal SRAM" |
| 952 | depends on FB_ATMEL && ARCH_AT91SAM9261 |
| 953 | help |
| 954 | Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want |
| 955 | to let frame buffer in external SDRAM. |
| 956 | |
Nicolas Ferre | 250a269 | 2007-07-21 04:37:59 -0700 | [diff] [blame] | 957 | config FB_ATMEL_STN |
| 958 | bool "Use a STN display with AT91/AT32 LCD Controller" |
Nicolas Ferre | 915190f | 2009-07-21 11:31:29 +0100 | [diff] [blame] | 959 | depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK) |
Nicolas Ferre | 250a269 | 2007-07-21 04:37:59 -0700 | [diff] [blame] | 960 | default n |
| 961 | help |
| 962 | Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD |
| 963 | Controller. Say N if you want to connect a TFT. |
| 964 | |
| 965 | If unsure, say N. |
| 966 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 967 | config FB_NVIDIA |
| 968 | tristate "nVidia Framebuffer Support" |
| 969 | depends on FB && PCI |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 970 | select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 971 | select FB_MODE_HELPERS |
| 972 | select FB_CFB_FILLRECT |
| 973 | select FB_CFB_COPYAREA |
| 974 | select FB_CFB_IMAGEBLIT |
Akinobu Mita | 1c66768 | 2006-12-08 02:36:26 -0800 | [diff] [blame] | 975 | select BITREVERSE |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 976 | select VGASTATE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 977 | help |
| 978 | This driver supports graphics boards with the nVidia chips, TNT |
| 979 | and newer. For very old chipsets, such as the RIVA128, then use |
| 980 | the rivafb. |
| 981 | Say Y if you have such a graphics board. |
| 982 | |
| 983 | To compile this driver as a module, choose M here: the |
| 984 | module will be called nvidiafb. |
| 985 | |
| 986 | config FB_NVIDIA_I2C |
| 987 | bool "Enable DDC Support" |
Benjamin Herrenschmidt | 85f1503 | 2005-11-07 01:00:30 -0800 | [diff] [blame] | 988 | depends on FB_NVIDIA |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 989 | select FB_DDC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 990 | help |
| 991 | This enables I2C support for nVidia Chipsets. This is used |
| 992 | only for getting EDID information from the attached display |
| 993 | allowing for robust video mode handling and switching. |
| 994 | |
| 995 | Because fbdev-2.6 requires that drivers must be able to |
| 996 | independently validate video mode parameters, you should say Y |
| 997 | here. |
| 998 | |
Jean Delvare | 647f2e7 | 2007-05-10 22:23:29 -0700 | [diff] [blame] | 999 | config FB_NVIDIA_DEBUG |
| 1000 | bool "Lots of debug output" |
| 1001 | depends on FB_NVIDIA |
| 1002 | default n |
| 1003 | help |
| 1004 | Say Y here if you want the nVidia driver to output all sorts |
| 1005 | of debugging information to provide to the maintainer when |
| 1006 | something goes wrong. |
| 1007 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1008 | config FB_NVIDIA_BACKLIGHT |
| 1009 | bool "Support for backlight control" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1010 | depends on FB_NVIDIA |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1011 | default y |
| 1012 | help |
| 1013 | Say Y here if you want to control the backlight of your display. |
| 1014 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1015 | config FB_RIVA |
| 1016 | tristate "nVidia Riva support" |
| 1017 | depends on FB && PCI |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1018 | select FB_BACKLIGHT if FB_RIVA_BACKLIGHT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1019 | select FB_MODE_HELPERS |
| 1020 | select FB_CFB_FILLRECT |
| 1021 | select FB_CFB_COPYAREA |
| 1022 | select FB_CFB_IMAGEBLIT |
Akinobu Mita | 1c66768 | 2006-12-08 02:36:26 -0800 | [diff] [blame] | 1023 | select BITREVERSE |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 1024 | select VGASTATE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1025 | help |
| 1026 | This driver supports graphics boards with the nVidia Riva/Geforce |
| 1027 | chips. |
| 1028 | Say Y if you have such a graphics board. |
| 1029 | |
| 1030 | To compile this driver as a module, choose M here: the |
| 1031 | module will be called rivafb. |
| 1032 | |
| 1033 | config FB_RIVA_I2C |
| 1034 | bool "Enable DDC Support" |
| 1035 | depends on FB_RIVA |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 1036 | select FB_DDC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1037 | help |
| 1038 | This enables I2C support for nVidia Chipsets. This is used |
| 1039 | only for getting EDID information from the attached display |
| 1040 | allowing for robust video mode handling and switching. |
| 1041 | |
| 1042 | Because fbdev-2.6 requires that drivers must be able to |
| 1043 | independently validate video mode parameters, you should say Y |
| 1044 | here. |
| 1045 | |
| 1046 | config FB_RIVA_DEBUG |
Jean Delvare | 647f2e7 | 2007-05-10 22:23:29 -0700 | [diff] [blame] | 1047 | bool "Lots of debug output" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1048 | depends on FB_RIVA |
| 1049 | default n |
| 1050 | help |
| 1051 | Say Y here if you want the Riva driver to output all sorts |
Matt LaPlante | 0950960 | 2006-10-03 22:31:37 +0200 | [diff] [blame] | 1052 | of debugging information to provide to the maintainer when |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1053 | something goes wrong. |
| 1054 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1055 | config FB_RIVA_BACKLIGHT |
| 1056 | bool "Support for backlight control" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1057 | depends on FB_RIVA |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1058 | default y |
| 1059 | help |
| 1060 | Say Y here if you want to control the backlight of your display. |
| 1061 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1062 | config FB_I810 |
| 1063 | tristate "Intel 810/815 support (EXPERIMENTAL)" |
Krzysztof Helt | a1a5c3b | 2009-02-18 14:48:38 -0800 | [diff] [blame] | 1064 | depends on EXPERIMENTAL && FB && PCI && X86_32 && AGP_INTEL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1065 | select FB_MODE_HELPERS |
| 1066 | select FB_CFB_FILLRECT |
| 1067 | select FB_CFB_COPYAREA |
| 1068 | select FB_CFB_IMAGEBLIT |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 1069 | select VGASTATE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1070 | help |
| 1071 | This driver supports the on-board graphics built in to the Intel 810 |
| 1072 | and 815 chipsets. Say Y if you have and plan to use such a board. |
| 1073 | |
| 1074 | To compile this driver as a module, choose M here: the |
| 1075 | module will be called i810fb. |
| 1076 | |
| 1077 | For more information, please read |
| 1078 | <file:Documentation/fb/intel810.txt> |
| 1079 | |
| 1080 | config FB_I810_GTF |
| 1081 | bool "use VESA Generalized Timing Formula" |
| 1082 | depends on FB_I810 |
| 1083 | help |
| 1084 | If you say Y, then the VESA standard, Generalized Timing Formula |
| 1085 | or GTF, will be used to calculate the required video timing values |
| 1086 | per video mode. Since the GTF allows nondiscrete timings |
| 1087 | (nondiscrete being a range of values as opposed to discrete being a |
| 1088 | set of values), you'll be able to use any combination of horizontal |
| 1089 | and vertical resolutions, and vertical refresh rates without having |
| 1090 | to specify your own timing parameters. This is especially useful |
| 1091 | to maximize the performance of an aging display, or if you just |
| 1092 | have a display with nonstandard dimensions. A VESA compliant |
| 1093 | monitor is recommended, but can still work with non-compliant ones. |
| 1094 | If you need or want this, then select this option. The timings may |
| 1095 | not be compliant with Intel's recommended values. Use at your own |
| 1096 | risk. |
| 1097 | |
| 1098 | If you say N, the driver will revert to discrete video timings |
| 1099 | using a set recommended by Intel in their documentation. |
| 1100 | |
| 1101 | If unsure, say N. |
| 1102 | |
Antonino A. Daplas | 74f6ae8 | 2005-09-09 13:10:04 -0700 | [diff] [blame] | 1103 | config FB_I810_I2C |
| 1104 | bool "Enable DDC Support" |
Antonino A. Daplas | db84502 | 2005-09-13 01:25:02 -0700 | [diff] [blame] | 1105 | depends on FB_I810 && FB_I810_GTF |
Antonino A. Daplas | e80987f | 2006-10-03 01:14:44 -0700 | [diff] [blame] | 1106 | select FB_DDC |
Antonino A. Daplas | 74f6ae8 | 2005-09-09 13:10:04 -0700 | [diff] [blame] | 1107 | help |
| 1108 | |
Alan Hourihane | dbe7e42 | 2007-05-08 00:39:25 -0700 | [diff] [blame] | 1109 | config FB_LE80578 |
| 1110 | tristate "Intel LE80578 (Vermilion) support" |
| 1111 | depends on FB && PCI && X86 |
| 1112 | select FB_MODE_HELPERS |
| 1113 | select FB_CFB_FILLRECT |
| 1114 | select FB_CFB_COPYAREA |
| 1115 | select FB_CFB_IMAGEBLIT |
| 1116 | help |
| 1117 | This driver supports the LE80578 (Vermilion Range) chipset |
| 1118 | |
| 1119 | config FB_CARILLO_RANCH |
| 1120 | tristate "Intel Carillo Ranch support" |
| 1121 | depends on FB_LE80578 && FB && PCI && X86 |
| 1122 | help |
| 1123 | This driver supports the LE80578 (Carillo Ranch) board |
| 1124 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1125 | config FB_INTEL |
Maik Broemme | 0e170c7 | 2008-04-28 02:15:43 -0700 | [diff] [blame] | 1126 | tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)" |
Jesse Barnes | ba0ab82 | 2009-07-03 11:24:46 -0700 | [diff] [blame] | 1127 | depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL && EMBEDDED |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1128 | select FB_MODE_HELPERS |
| 1129 | select FB_CFB_FILLRECT |
| 1130 | select FB_CFB_COPYAREA |
| 1131 | select FB_CFB_IMAGEBLIT |
Krzysztof Helt | 4b19828 | 2009-06-18 16:49:21 -0700 | [diff] [blame] | 1132 | select FB_BOOT_VESA_SUPPORT if FB_INTEL = y |
Jesse Barnes | ba0ab82 | 2009-07-03 11:24:46 -0700 | [diff] [blame] | 1133 | depends on !DRM_I915 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1134 | help |
| 1135 | This driver supports the on-board graphics built in to the Intel |
Maik Broemme | 0e170c7 | 2008-04-28 02:15:43 -0700 | [diff] [blame] | 1136 | 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1137 | Say Y if you have and plan to use such a board. |
| 1138 | |
Krzysztof Helt | 4b19828 | 2009-06-18 16:49:21 -0700 | [diff] [blame] | 1139 | To make FB_INTELFB=Y work you need to say AGP_INTEL=y too. |
| 1140 | |
Dennis Munsie | 1f6e844 | 2006-06-20 14:55:55 -0400 | [diff] [blame] | 1141 | To compile this driver as a module, choose M here: the |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1142 | module will be called intelfb. |
| 1143 | |
Christian Merkle | d463d34 | 2006-08-22 10:07:01 +1000 | [diff] [blame] | 1144 | For more information, please read <file:Documentation/fb/intelfb.txt> |
| 1145 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1146 | config FB_INTEL_DEBUG |
Dennis Munsie | 1f6e844 | 2006-06-20 14:55:55 -0400 | [diff] [blame] | 1147 | bool "Intel driver Debug Messages" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1148 | depends on FB_INTEL |
| 1149 | ---help--- |
| 1150 | Say Y here if you want the Intel driver to output all sorts |
Matt LaPlante | 0950960 | 2006-10-03 22:31:37 +0200 | [diff] [blame] | 1151 | of debugging information to provide to the maintainer when |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1152 | something goes wrong. |
| 1153 | |
Dennis Munsie | 1f6e844 | 2006-06-20 14:55:55 -0400 | [diff] [blame] | 1154 | config FB_INTEL_I2C |
| 1155 | bool "DDC/I2C for Intel framebuffer support" |
| 1156 | depends on FB_INTEL |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 1157 | select FB_DDC |
Dennis Munsie | 1f6e844 | 2006-06-20 14:55:55 -0400 | [diff] [blame] | 1158 | default y |
| 1159 | help |
| 1160 | Say Y here if you want DDC/I2C support for your on-board Intel graphics. |
| 1161 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1162 | config FB_MATROX |
| 1163 | tristate "Matrox acceleration" |
| 1164 | depends on FB && PCI |
| 1165 | select FB_CFB_FILLRECT |
| 1166 | select FB_CFB_COPYAREA |
| 1167 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1168 | select FB_TILEBLITTING |
| 1169 | select FB_MACMODES if PPC_PMAC |
| 1170 | ---help--- |
| 1171 | Say Y here if you have a Matrox Millennium, Matrox Millennium II, |
| 1172 | Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox |
| 1173 | Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video, |
| 1174 | Matrox G400, G450 or G550 card in your box. |
| 1175 | |
| 1176 | To compile this driver as a module, choose M here: the |
| 1177 | module will be called matroxfb. |
| 1178 | |
| 1179 | You can pass several parameters to the driver at boot time or at |
| 1180 | module load time. The parameters look like "video=matrox:XXX", and |
| 1181 | are described in <file:Documentation/fb/matroxfb.txt>. |
| 1182 | |
| 1183 | config FB_MATROX_MILLENIUM |
| 1184 | bool "Millennium I/II support" |
| 1185 | depends on FB_MATROX |
| 1186 | help |
| 1187 | Say Y here if you have a Matrox Millennium or Matrox Millennium II |
| 1188 | video card. If you select "Advanced lowlevel driver options" below, |
| 1189 | you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp |
| 1190 | packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can |
| 1191 | also use font widths different from 8. |
| 1192 | |
| 1193 | config FB_MATROX_MYSTIQUE |
| 1194 | bool "Mystique support" |
| 1195 | depends on FB_MATROX |
| 1196 | help |
| 1197 | Say Y here if you have a Matrox Mystique or Matrox Mystique 220 |
| 1198 | video card. If you select "Advanced lowlevel driver options" below, |
| 1199 | you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp |
| 1200 | packed pixel and 32 bpp packed pixel. You can also use font widths |
| 1201 | different from 8. |
| 1202 | |
| 1203 | config FB_MATROX_G |
| 1204 | bool "G100/G200/G400/G450/G550 support" |
| 1205 | depends on FB_MATROX |
| 1206 | ---help--- |
| 1207 | Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based |
| 1208 | video card. If you select "Advanced lowlevel driver options", you |
| 1209 | should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed |
| 1210 | pixel and 32 bpp packed pixel. You can also use font widths |
| 1211 | different from 8. |
| 1212 | |
Jean Delvare | ee83126 | 2009-05-12 13:19:41 -0700 | [diff] [blame] | 1213 | If you need support for G400 secondary head, you must say Y to |
| 1214 | "Matrox I2C support" and "G400 second head support" right below. |
| 1215 | G450/G550 secondary head and digital output are supported without |
| 1216 | additional modules. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1217 | |
| 1218 | The driver starts in monitor mode. You must use the matroxset tool |
| 1219 | (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to |
| 1220 | swap primary and secondary head outputs, or to change output mode. |
| 1221 | Secondary head driver always start in 640x480 resolution and you |
| 1222 | must use fbset to change it. |
| 1223 | |
| 1224 | Do not forget that second head supports only 16 and 32 bpp |
| 1225 | packed pixels, so it is a good idea to compile them into the kernel |
| 1226 | too. You can use only some font widths, as the driver uses generic |
| 1227 | painting procedures (the secondary head does not use acceleration |
| 1228 | engine). |
| 1229 | |
| 1230 | G450/G550 hardware can display TV picture only from secondary CRTC, |
| 1231 | and it performs no scaling, so picture must have 525 or 625 lines. |
| 1232 | |
| 1233 | config FB_MATROX_I2C |
| 1234 | tristate "Matrox I2C support" |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 1235 | depends on FB_MATROX |
| 1236 | select FB_DDC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1237 | ---help--- |
| 1238 | This drivers creates I2C buses which are needed for accessing the |
| 1239 | DDC (I2C) bus present on all Matroxes, an I2C bus which |
| 1240 | interconnects Matrox optional devices, like MGA-TVO on G200 and |
| 1241 | G400, and the secondary head DDC bus, present on G400 only. |
| 1242 | |
| 1243 | You can say Y or M here if you want to experiment with monitor |
| 1244 | detection code. You must say Y or M here if you want to use either |
| 1245 | second head of G400 or MGA-TVO on G200 or G400. |
| 1246 | |
| 1247 | If you compile it as module, it will create a module named |
| 1248 | i2c-matroxfb. |
| 1249 | |
| 1250 | config FB_MATROX_MAVEN |
| 1251 | tristate "G400 second head support" |
| 1252 | depends on FB_MATROX_G && FB_MATROX_I2C |
| 1253 | ---help--- |
| 1254 | WARNING !!! This support does not work with G450 !!! |
| 1255 | |
| 1256 | Say Y or M here if you want to use a secondary head (meaning two |
| 1257 | monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary |
| 1258 | head is not compatible with accelerated XFree 3.3.x SVGA servers - |
| 1259 | secondary head output is blanked while you are in X. With XFree |
| 1260 | 3.9.17 preview you can use both heads if you use SVGA over fbdev or |
| 1261 | the fbdev driver on first head and the fbdev driver on second head. |
| 1262 | |
| 1263 | If you compile it as module, two modules are created, |
| 1264 | matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for |
| 1265 | both G200 and G400, matroxfb_crtc2 is needed only by G400. You must |
| 1266 | also load i2c-matroxfb to get it to run. |
| 1267 | |
| 1268 | The driver starts in monitor mode and you must use the matroxset |
| 1269 | tool (available at |
| 1270 | <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to |
| 1271 | PAL or NTSC or to swap primary and secondary head outputs. |
| 1272 | Secondary head driver also always start in 640x480 resolution, you |
| 1273 | must use fbset to change it. |
| 1274 | |
| 1275 | Also do not forget that second head supports only 16 and 32 bpp |
| 1276 | packed pixels, so it is a good idea to compile them into the kernel |
| 1277 | too. You can use only some font widths, as the driver uses generic |
| 1278 | painting procedures (the secondary head does not use acceleration |
| 1279 | engine). |
| 1280 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1281 | config FB_RADEON |
| 1282 | tristate "ATI Radeon display support" |
| 1283 | depends on FB && PCI |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1284 | select FB_BACKLIGHT if FB_RADEON_BACKLIGHT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1285 | select FB_MODE_HELPERS |
| 1286 | select FB_CFB_FILLRECT |
| 1287 | select FB_CFB_COPYAREA |
| 1288 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1289 | select FB_MACMODES if PPC_OF |
| 1290 | help |
| 1291 | Choose this option if you want to use an ATI Radeon graphics card as |
| 1292 | a framebuffer device. There are both PCI and AGP versions. You |
| 1293 | don't need to choose this to run the Radeon in plain VGA mode. |
| 1294 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1295 | There is a product page at |
Antonino A. Daplas | f510a3c | 2005-09-09 13:04:41 -0700 | [diff] [blame] | 1296 | http://apps.ati.com/ATIcompare/ |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1297 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1298 | config FB_RADEON_I2C |
| 1299 | bool "DDC/I2C for ATI Radeon support" |
| 1300 | depends on FB_RADEON |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 1301 | select FB_DDC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1302 | default y |
| 1303 | help |
| 1304 | Say Y here if you want DDC/I2C support for your Radeon board. |
| 1305 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1306 | config FB_RADEON_BACKLIGHT |
| 1307 | bool "Support for backlight control" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1308 | depends on FB_RADEON |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1309 | default y |
| 1310 | help |
| 1311 | Say Y here if you want to control the backlight of your display. |
| 1312 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1313 | config FB_RADEON_DEBUG |
| 1314 | bool "Lots of debug output from Radeon driver" |
| 1315 | depends on FB_RADEON |
| 1316 | default n |
| 1317 | help |
| 1318 | Say Y here if you want the Radeon driver to output all sorts |
Matt LaPlante | 0950960 | 2006-10-03 22:31:37 +0200 | [diff] [blame] | 1319 | of debugging information to provide to the maintainer when |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1320 | something goes wrong. |
| 1321 | |
| 1322 | config FB_ATY128 |
| 1323 | tristate "ATI Rage128 display support" |
| 1324 | depends on FB && PCI |
| 1325 | select FB_CFB_FILLRECT |
| 1326 | select FB_CFB_COPYAREA |
| 1327 | select FB_CFB_IMAGEBLIT |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1328 | select FB_BACKLIGHT if FB_ATY128_BACKLIGHT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1329 | select FB_MACMODES if PPC_PMAC |
| 1330 | help |
| 1331 | This driver supports graphics boards with the ATI Rage128 chips. |
| 1332 | Say Y if you have such a graphics board and read |
| 1333 | <file:Documentation/fb/aty128fb.txt>. |
| 1334 | |
| 1335 | To compile this driver as a module, choose M here: the |
| 1336 | module will be called aty128fb. |
| 1337 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1338 | config FB_ATY128_BACKLIGHT |
| 1339 | bool "Support for backlight control" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1340 | depends on FB_ATY128 |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1341 | default y |
| 1342 | help |
| 1343 | Say Y here if you want to control the backlight of your display. |
| 1344 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1345 | config FB_ATY |
| 1346 | tristate "ATI Mach64 display support" if PCI || ATARI |
Andrew Morton | f2e782e | 2006-04-10 22:55:45 -0700 | [diff] [blame] | 1347 | depends on FB && !SPARC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1348 | select FB_CFB_FILLRECT |
| 1349 | select FB_CFB_COPYAREA |
| 1350 | select FB_CFB_IMAGEBLIT |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1351 | select FB_BACKLIGHT if FB_ATY_BACKLIGHT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1352 | select FB_MACMODES if PPC |
| 1353 | help |
| 1354 | This driver supports graphics boards with the ATI Mach64 chips. |
| 1355 | Say Y if you have such a graphics board. |
| 1356 | |
| 1357 | To compile this driver as a module, choose M here: the |
| 1358 | module will be called atyfb. |
| 1359 | |
| 1360 | config FB_ATY_CT |
| 1361 | bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support" |
| 1362 | depends on PCI && FB_ATY |
Krzysztof Helt | 8d74c1f | 2007-05-23 13:57:46 -0700 | [diff] [blame] | 1363 | default y if SPARC64 && PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1364 | help |
| 1365 | Say Y here to support use of ATI's 64-bit Rage boards (or other |
| 1366 | boards based on the Mach64 CT, VT, GT, and LT chipsets) as a |
| 1367 | framebuffer device. The ATI product support page for these boards |
| 1368 | is at <http://support.ati.com/products/pc/mach64/>. |
| 1369 | |
| 1370 | config FB_ATY_GENERIC_LCD |
| 1371 | bool "Mach64 generic LCD support (EXPERIMENTAL)" |
| 1372 | depends on FB_ATY_CT |
| 1373 | help |
| 1374 | Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility, |
| 1375 | Rage XC, or Rage XL chipset. |
| 1376 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1377 | config FB_ATY_GX |
| 1378 | bool "Mach64 GX support" if PCI |
| 1379 | depends on FB_ATY |
| 1380 | default y if ATARI |
| 1381 | help |
| 1382 | Say Y here to support use of the ATI Mach64 Graphics Expression |
| 1383 | board (or other boards based on the Mach64 GX chipset) as a |
| 1384 | framebuffer device. The ATI product support page for these boards |
| 1385 | is at |
| 1386 | <http://support.ati.com/products/pc/mach64/graphics_xpression.html>. |
| 1387 | |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1388 | config FB_ATY_BACKLIGHT |
| 1389 | bool "Support for backlight control" |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 1390 | depends on FB_ATY |
Michael Hanselmann | 5474c12 | 2006-06-25 05:47:08 -0700 | [diff] [blame] | 1391 | default y |
| 1392 | help |
| 1393 | Say Y here if you want to control the backlight of your display. |
| 1394 | |
Ondrej Zajicek | a268422 | 2007-02-12 00:54:49 -0800 | [diff] [blame] | 1395 | config FB_S3 |
| 1396 | tristate "S3 Trio/Virge support" |
| 1397 | depends on FB && PCI |
| 1398 | select FB_CFB_FILLRECT |
| 1399 | select FB_CFB_COPYAREA |
| 1400 | select FB_CFB_IMAGEBLIT |
| 1401 | select FB_TILEBLITTING |
| 1402 | select FB_SVGALIB |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 1403 | select VGASTATE |
Antonino A. Daplas | 8db5166 | 2007-05-08 00:39:14 -0700 | [diff] [blame] | 1404 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
Ondrej Zajicek | a268422 | 2007-02-12 00:54:49 -0800 | [diff] [blame] | 1405 | ---help--- |
| 1406 | Driver for graphics boards with S3 Trio / S3 Virge chip. |
| 1407 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1408 | config FB_SAVAGE |
| 1409 | tristate "S3 Savage support" |
| 1410 | depends on FB && PCI && EXPERIMENTAL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1411 | select FB_MODE_HELPERS |
| 1412 | select FB_CFB_FILLRECT |
| 1413 | select FB_CFB_COPYAREA |
| 1414 | select FB_CFB_IMAGEBLIT |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 1415 | select VGASTATE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1416 | help |
| 1417 | This driver supports notebooks and computers with S3 Savage PCI/AGP |
| 1418 | chips. |
| 1419 | |
| 1420 | Say Y if you have such a graphics card. |
| 1421 | |
| 1422 | To compile this driver as a module, choose M here; the module |
| 1423 | will be called savagefb. |
| 1424 | |
| 1425 | config FB_SAVAGE_I2C |
| 1426 | bool "Enable DDC2 Support" |
| 1427 | depends on FB_SAVAGE |
James Simmons | 166f60d | 2007-03-06 01:42:02 -0800 | [diff] [blame] | 1428 | select FB_DDC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1429 | help |
| 1430 | This enables I2C support for S3 Savage Chipsets. This is used |
| 1431 | only for getting EDID information from the attached display |
| 1432 | allowing for robust video mode handling and switching. |
| 1433 | |
| 1434 | Because fbdev-2.6 requires that drivers must be able to |
| 1435 | independently validate video mode parameters, you should say Y |
| 1436 | here. |
| 1437 | |
| 1438 | config FB_SAVAGE_ACCEL |
| 1439 | bool "Enable Console Acceleration" |
| 1440 | depends on FB_SAVAGE |
| 1441 | default n |
| 1442 | help |
| 1443 | This option will compile in console acceleration support. If |
| 1444 | the resulting framebuffer console has bothersome glitches, then |
| 1445 | choose N here. |
| 1446 | |
| 1447 | config FB_SIS |
Thomas Winischhofer | 544393f | 2005-09-09 13:04:45 -0700 | [diff] [blame] | 1448 | tristate "SiS/XGI display support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1449 | depends on FB && PCI |
| 1450 | select FB_CFB_FILLRECT |
| 1451 | select FB_CFB_COPYAREA |
| 1452 | select FB_CFB_IMAGEBLIT |
Krzysztof Helt | 4b19828 | 2009-06-18 16:49:21 -0700 | [diff] [blame] | 1453 | select FB_BOOT_VESA_SUPPORT if FB_SIS = y |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1454 | help |
Thomas Winischhofer | 544393f | 2005-09-09 13:04:45 -0700 | [diff] [blame] | 1455 | This is the frame buffer device driver for the SiS 300, 315, 330 |
| 1456 | and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets. |
| 1457 | Specs available at <http://www.sis.com> and <http://www.xgitech.com>. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1458 | |
| 1459 | To compile this driver as a module, choose M here; the module |
| 1460 | will be called sisfb. |
| 1461 | |
| 1462 | config FB_SIS_300 |
| 1463 | bool "SiS 300 series support" |
| 1464 | depends on FB_SIS |
| 1465 | help |
| 1466 | Say Y here to support use of the SiS 300/305, 540, 630 and 730. |
| 1467 | |
| 1468 | config FB_SIS_315 |
Thomas Winischhofer | 544393f | 2005-09-09 13:04:45 -0700 | [diff] [blame] | 1469 | bool "SiS 315/330/340 series and XGI support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1470 | depends on FB_SIS |
| 1471 | help |
Thomas Winischhofer | 544393f | 2005-09-09 13:04:45 -0700 | [diff] [blame] | 1472 | Say Y here to support use of the SiS 315, 330 and 340 series |
| 1473 | (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well |
| 1474 | as XGI V3XT, V5, V8 and Z7. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1475 | |
Joseph Chan | 6bde3ed | 2008-10-15 22:03:20 -0700 | [diff] [blame] | 1476 | config FB_VIA |
| 1477 | tristate "VIA UniChrome (Pro) and Chrome9 display support" |
| 1478 | depends on FB && PCI |
| 1479 | select FB_CFB_FILLRECT |
| 1480 | select FB_CFB_COPYAREA |
| 1481 | select FB_CFB_IMAGEBLIT |
| 1482 | select FB_SOFT_CURSOR |
| 1483 | select I2C_ALGOBIT |
| 1484 | select I2C |
| 1485 | help |
| 1486 | This is the frame buffer device driver for Graphics chips of VIA |
| 1487 | UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/ |
| 1488 | CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896 |
| 1489 | /P4M900,VX800) |
| 1490 | Say Y if you have a VIA UniChrome graphics board. |
| 1491 | |
| 1492 | To compile this driver as a module, choose M here: the |
| 1493 | module will be called viafb. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1494 | config FB_NEOMAGIC |
| 1495 | tristate "NeoMagic display support" |
| 1496 | depends on FB && PCI |
| 1497 | select FB_MODE_HELPERS |
| 1498 | select FB_CFB_FILLRECT |
| 1499 | select FB_CFB_COPYAREA |
| 1500 | select FB_CFB_IMAGEBLIT |
Antonino A. Daplas | b2f594f | 2007-05-08 00:38:38 -0700 | [diff] [blame] | 1501 | select VGASTATE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1502 | help |
| 1503 | This driver supports notebooks with NeoMagic PCI chips. |
| 1504 | Say Y if you have such a graphics card. |
| 1505 | |
| 1506 | To compile this driver as a module, choose M here: the |
| 1507 | module will be called neofb. |
| 1508 | |
| 1509 | config FB_KYRO |
| 1510 | tristate "IMG Kyro support" |
| 1511 | depends on FB && PCI |
| 1512 | select FB_CFB_FILLRECT |
| 1513 | select FB_CFB_COPYAREA |
| 1514 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1515 | help |
| 1516 | Say Y here if you have a STG4000 / Kyro / PowerVR 3 based |
| 1517 | graphics board. |
| 1518 | |
| 1519 | To compile this driver as a module, choose M here: the |
| 1520 | module will be called kyrofb. |
| 1521 | |
| 1522 | config FB_3DFX |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 1523 | tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1524 | depends on FB && PCI |
| 1525 | select FB_CFB_IMAGEBLIT |
| 1526 | select FB_CFB_FILLRECT |
| 1527 | select FB_CFB_COPYAREA |
Krzysztof Helt | feff388 | 2009-04-06 19:01:03 -0700 | [diff] [blame] | 1528 | select FB_MODE_HELPERS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1529 | help |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 1530 | This driver supports graphics boards with the 3Dfx Banshee, |
| 1531 | Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have |
| 1532 | such a graphics board. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1533 | |
| 1534 | To compile this driver as a module, choose M here: the |
| 1535 | module will be called tdfxfb. |
| 1536 | |
| 1537 | config FB_3DFX_ACCEL |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 1538 | bool "3Dfx Acceleration functions (EXPERIMENTAL)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1539 | depends on FB_3DFX && EXPERIMENTAL |
| 1540 | ---help--- |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 1541 | This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer |
| 1542 | device driver with acceleration functions. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1543 | |
Krzysztof Helt | feff388 | 2009-04-06 19:01:03 -0700 | [diff] [blame] | 1544 | config FB_3DFX_I2C |
| 1545 | bool "Enable DDC/I2C support" |
| 1546 | depends on FB_3DFX && EXPERIMENTAL |
| 1547 | select FB_DDC |
| 1548 | default y |
| 1549 | help |
| 1550 | Say Y here if you want DDC/I2C support for your 3dfx Voodoo3. |
| 1551 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1552 | config FB_VOODOO1 |
| 1553 | tristate "3Dfx Voodoo Graphics (sst1) support" |
| 1554 | depends on FB && PCI |
| 1555 | select FB_CFB_FILLRECT |
| 1556 | select FB_CFB_COPYAREA |
| 1557 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1558 | ---help--- |
| 1559 | Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or |
| 1560 | Voodoo2 (cvg) based graphics card. |
| 1561 | |
| 1562 | To compile this driver as a module, choose M here: the |
| 1563 | module will be called sstfb. |
| 1564 | |
| 1565 | WARNING: Do not use any application that uses the 3D engine |
| 1566 | (namely glide) while using this driver. |
Dirk Hohndel | e403149 | 2007-10-30 13:37:19 -0700 | [diff] [blame] | 1567 | Please read the <file:Documentation/fb/sstfb.txt> for supported |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1568 | options and other important info support. |
| 1569 | |
Ondrej Zajicek | 558b7bd | 2007-05-09 02:35:31 -0700 | [diff] [blame] | 1570 | config FB_VT8623 |
| 1571 | tristate "VIA VT8623 support" |
| 1572 | depends on FB && PCI |
| 1573 | select FB_CFB_FILLRECT |
| 1574 | select FB_CFB_COPYAREA |
| 1575 | select FB_CFB_IMAGEBLIT |
| 1576 | select FB_TILEBLITTING |
| 1577 | select FB_SVGALIB |
| 1578 | select VGASTATE |
| 1579 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
| 1580 | ---help--- |
| 1581 | Driver for CastleRock integrated graphics core in the |
| 1582 | VIA VT8623 [Apollo CLE266] chipset. |
| 1583 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1584 | config FB_TRIDENT |
Krzysztof Helt | 04645fc | 2009-03-31 15:25:48 -0700 | [diff] [blame] | 1585 | tristate "Trident/CyberXXX/CyberBlade support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1586 | depends on FB && PCI |
| 1587 | select FB_CFB_FILLRECT |
| 1588 | select FB_CFB_COPYAREA |
| 1589 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1590 | ---help--- |
Krzysztof Helt | 4edad7f | 2008-10-15 22:03:32 -0700 | [diff] [blame] | 1591 | This is the frame buffer device driver for Trident PCI/AGP chipsets. |
| 1592 | Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D |
| 1593 | and Blade XP. |
| 1594 | There are also integrated versions of these chips called CyberXXXX, |
| 1595 | CyberImage or CyberBlade. These chips are mostly found in laptops |
Krzysztof Helt | ddb53d4 | 2009-03-31 15:25:40 -0700 | [diff] [blame] | 1596 | but also on some motherboards including early VIA EPIA motherboards. |
| 1597 | For more information, read <file:Documentation/fb/tridentfb.txt> |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1598 | |
| 1599 | Say Y if you have such a graphics board. |
| 1600 | |
| 1601 | To compile this driver as a module, choose M here: the |
| 1602 | module will be called tridentfb. |
| 1603 | |
Ondrej Zajicek | 681e147 | 2007-05-09 02:35:31 -0700 | [diff] [blame] | 1604 | config FB_ARK |
| 1605 | tristate "ARK 2000PV support" |
| 1606 | depends on FB && PCI |
| 1607 | select FB_CFB_FILLRECT |
| 1608 | select FB_CFB_COPYAREA |
| 1609 | select FB_CFB_IMAGEBLIT |
| 1610 | select FB_TILEBLITTING |
| 1611 | select FB_SVGALIB |
| 1612 | select VGASTATE |
| 1613 | select FONT_8x16 if FRAMEBUFFER_CONSOLE |
| 1614 | ---help--- |
| 1615 | Driver for PCI graphics boards with ARK 2000PV chip |
| 1616 | and ICS 5342 RAMDAC. |
| 1617 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1618 | config FB_PM3 |
Krzysztof Helt | f23a06f | 2007-05-10 22:23:25 -0700 | [diff] [blame] | 1619 | tristate "Permedia3 support (EXPERIMENTAL)" |
| 1620 | depends on FB && PCI && EXPERIMENTAL |
| 1621 | select FB_CFB_FILLRECT |
| 1622 | select FB_CFB_COPYAREA |
| 1623 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1624 | help |
| 1625 | This is the frame buffer device driver for the 3DLabs Permedia3 |
| 1626 | chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 & |
| 1627 | similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000 |
| 1628 | and maybe other boards. |
| 1629 | |
Sebastian Siewior | 2ece5f43 | 2008-07-23 21:30:49 -0700 | [diff] [blame] | 1630 | config FB_CARMINE |
| 1631 | tristate "Fujitsu carmine frame buffer support" |
| 1632 | depends on FB && PCI |
| 1633 | select FB_CFB_FILLRECT |
| 1634 | select FB_CFB_COPYAREA |
| 1635 | select FB_CFB_IMAGEBLIT |
| 1636 | help |
| 1637 | This is the frame buffer device driver for the Fujitsu Carmine chip. |
| 1638 | The driver provides two independent frame buffer devices. |
| 1639 | |
| 1640 | choice |
| 1641 | depends on FB_CARMINE |
| 1642 | prompt "DRAM timing" |
| 1643 | default FB_CARMINE_DRAM_EVAL |
| 1644 | |
| 1645 | config FB_CARMINE_DRAM_EVAL |
| 1646 | bool "Eval board timings" |
| 1647 | help |
| 1648 | Use timings which work on the eval card. |
| 1649 | |
| 1650 | config CARMINE_DRAM_CUSTOM |
| 1651 | bool "Custom board timings" |
| 1652 | help |
| 1653 | Use custom board timings. |
| 1654 | endchoice |
| 1655 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1656 | config FB_AU1100 |
| 1657 | bool "Au1100 LCD Driver" |
Ralf Baechle | d1709e4 | 2007-07-23 18:43:50 -0700 | [diff] [blame] | 1658 | depends on (FB = y) && MIPS && SOC_AU1100 |
| 1659 | select FB_CFB_FILLRECT |
| 1660 | select FB_CFB_COPYAREA |
| 1661 | select FB_CFB_IMAGEBLIT |
| 1662 | help |
| 1663 | This is the framebuffer driver for the AMD Au1100 SOC. It can drive |
| 1664 | various panels and CRTs by passing in kernel cmd line option |
| 1665 | au1100fb:panel=<name>. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1666 | |
Ralf Baechle | f95ec3c | 2006-03-27 01:17:27 -0800 | [diff] [blame] | 1667 | config FB_AU1200 |
| 1668 | bool "Au1200 LCD Driver" |
Geert Uytterhoeven | 833f806 | 2007-03-16 13:38:23 -0800 | [diff] [blame] | 1669 | depends on (FB = y) && MIPS && SOC_AU1200 |
Ralf Baechle | f95ec3c | 2006-03-27 01:17:27 -0800 | [diff] [blame] | 1670 | select FB_CFB_FILLRECT |
| 1671 | select FB_CFB_COPYAREA |
| 1672 | select FB_CFB_IMAGEBLIT |
| 1673 | help |
| 1674 | This is the framebuffer driver for the AMD Au1200 SOC. It can drive |
| 1675 | various panels and CRTs by passing in kernel cmd line option |
| 1676 | au1200fb:panel=<name>. |
| 1677 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1678 | source "drivers/video/geode/Kconfig" |
| 1679 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1680 | config FB_HIT |
| 1681 | tristate "HD64461 Frame Buffer support" |
| 1682 | depends on FB && HD64461 |
| 1683 | select FB_CFB_FILLRECT |
| 1684 | select FB_CFB_COPYAREA |
| 1685 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1686 | help |
| 1687 | This is the frame buffer device driver for the Hitachi HD64461 LCD |
| 1688 | frame buffer card. |
| 1689 | |
| 1690 | config FB_PMAG_AA |
| 1691 | bool "PMAG-AA TURBOchannel framebuffer support" |
Maciej W. Rozycki | a935000 | 2005-06-13 19:50:42 +0000 | [diff] [blame] | 1692 | depends on (FB = y) && TC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1693 | select FB_CFB_FILLRECT |
| 1694 | select FB_CFB_COPYAREA |
| 1695 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1696 | help |
| 1697 | Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1) |
| 1698 | used mainly in the MIPS-based DECstation series. |
| 1699 | |
| 1700 | config FB_PMAG_BA |
Maciej W. Rozycki | 335dc50 | 2007-02-05 16:28:28 -0800 | [diff] [blame] | 1701 | tristate "PMAG-BA TURBOchannel framebuffer support" |
| 1702 | depends on FB && TC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1703 | select FB_CFB_FILLRECT |
| 1704 | select FB_CFB_COPYAREA |
| 1705 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1706 | help |
| 1707 | Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8) |
| 1708 | used mainly in the MIPS-based DECstation series. |
| 1709 | |
| 1710 | config FB_PMAGB_B |
Maciej W. Rozycki | 9084b00 | 2007-02-05 16:28:29 -0800 | [diff] [blame] | 1711 | tristate "PMAGB-B TURBOchannel framebuffer support" |
Maciej W. Rozycki | 28ea28a | 2007-10-16 01:29:28 -0700 | [diff] [blame] | 1712 | depends on FB && TC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1713 | select FB_CFB_FILLRECT |
| 1714 | select FB_CFB_COPYAREA |
| 1715 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1716 | help |
| 1717 | Support for the PMAGB-B TURBOchannel framebuffer card used mainly |
| 1718 | in the MIPS-based DECstation series. The card is currently only |
| 1719 | supported in 1280x1024x8 mode. |
| 1720 | |
| 1721 | config FB_MAXINE |
| 1722 | bool "Maxine (Personal DECstation) onboard framebuffer support" |
Maciej W. Rozycki | a935000 | 2005-06-13 19:50:42 +0000 | [diff] [blame] | 1723 | depends on (FB = y) && MACH_DECSTATION |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1724 | select FB_CFB_FILLRECT |
| 1725 | select FB_CFB_COPYAREA |
| 1726 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1727 | help |
| 1728 | Support for the onboard framebuffer (1024x768x8) in the Personal |
| 1729 | DECstation series (Personal DECstation 5000/20, /25, /33, /50, |
| 1730 | Codename "Maxine"). |
| 1731 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1732 | config FB_G364 |
Yoichi Yuasa | b38817d | 2005-07-27 11:43:28 -0700 | [diff] [blame] | 1733 | bool "G364 frame buffer support" |
| 1734 | depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1735 | select FB_CFB_FILLRECT |
| 1736 | select FB_CFB_COPYAREA |
| 1737 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1738 | help |
| 1739 | The G364 driver is the framebuffer used in MIPS Magnum 4000 and |
| 1740 | Olivetti M700-10 systems. |
| 1741 | |
| 1742 | config FB_68328 |
| 1743 | bool "Motorola 68328 native frame buffer support" |
Geert Uytterhoeven | 833f806 | 2007-03-16 13:38:23 -0800 | [diff] [blame] | 1744 | depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1745 | select FB_CFB_FILLRECT |
| 1746 | select FB_CFB_COPYAREA |
| 1747 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1748 | help |
| 1749 | Say Y here if you want to support the built-in frame buffer of |
| 1750 | the Motorola 68328 CPU family. |
| 1751 | |
Lennert Buytenhek | 638772c | 2009-02-11 17:25:24 +0800 | [diff] [blame] | 1752 | config FB_PXA168 |
| 1753 | tristate "PXA168/910 LCD framebuffer support" |
| 1754 | depends on FB && (CPU_PXA168 || CPU_PXA910) |
| 1755 | select FB_CFB_FILLRECT |
| 1756 | select FB_CFB_COPYAREA |
| 1757 | select FB_CFB_IMAGEBLIT |
| 1758 | ---help--- |
| 1759 | Frame buffer driver for the built-in LCD controller in the Marvell |
| 1760 | MMP processor. |
| 1761 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1762 | config FB_PXA |
| 1763 | tristate "PXA LCD framebuffer support" |
| 1764 | depends on FB && ARCH_PXA |
| 1765 | select FB_CFB_FILLRECT |
| 1766 | select FB_CFB_COPYAREA |
| 1767 | select FB_CFB_IMAGEBLIT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1768 | ---help--- |
| 1769 | Frame buffer driver for the built-in LCD controller in the Intel |
| 1770 | PXA2x0 processor. |
| 1771 | |
| 1772 | This driver is also available as a module ( = code which can be |
| 1773 | inserted and removed from the running kernel whenever you want). The |
YOSHIFUJI Hideaki | 74b4f04 | 2006-01-09 20:53:46 -0800 | [diff] [blame] | 1774 | module will be called pxafb. If you want to compile it as a module, |
Alexander E. Patrakov | 39f5fb3 | 2007-03-16 18:28:43 +0500 | [diff] [blame] | 1775 | say M here and read <file:Documentation/kbuild/modules.txt>. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1776 | |
| 1777 | If unsure, say N. |
| 1778 | |
Eric Miao | 198fc10 | 2008-12-23 17:49:43 +0800 | [diff] [blame] | 1779 | config FB_PXA_OVERLAY |
| 1780 | bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer" |
| 1781 | default n |
| 1782 | depends on FB_PXA && (PXA27x || PXA3xx) |
| 1783 | |
Eric Miao | 3c42a44 | 2008-04-30 00:52:26 -0700 | [diff] [blame] | 1784 | config FB_PXA_SMARTPANEL |
| 1785 | bool "PXA Smartpanel LCD support" |
Eric Miao | 7f1133c | 2008-04-30 00:52:27 -0700 | [diff] [blame] | 1786 | default n |
Eric Miao | 3c42a44 | 2008-04-30 00:52:26 -0700 | [diff] [blame] | 1787 | depends on FB_PXA |
| 1788 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1789 | config FB_PXA_PARAMETERS |
| 1790 | bool "PXA LCD command line parameters" |
| 1791 | default n |
| 1792 | depends on FB_PXA |
| 1793 | ---help--- |
| 1794 | Enable the use of kernel command line or module parameters |
| 1795 | to configure the physical properties of the LCD panel when |
| 1796 | using the PXA LCD driver. |
| 1797 | |
| 1798 | This option allows you to override the panel parameters |
| 1799 | supplied by the platform in order to support multiple |
| 1800 | different models of flatpanel. If you will only be using a |
| 1801 | single model of flatpanel then you can safely leave this |
| 1802 | option disabled. |
| 1803 | |
| 1804 | <file:Documentation/fb/pxafb.txt> describes the available parameters. |
| 1805 | |
Mike Rapoport | 22caf04 | 2006-07-14 00:24:34 -0700 | [diff] [blame] | 1806 | config FB_MBX |
| 1807 | tristate "2700G LCD framebuffer support" |
| 1808 | depends on FB && ARCH_PXA |
| 1809 | select FB_CFB_FILLRECT |
| 1810 | select FB_CFB_COPYAREA |
| 1811 | select FB_CFB_IMAGEBLIT |
| 1812 | ---help--- |
| 1813 | Framebuffer driver for the Intel 2700G (Marathon) Graphics |
| 1814 | Accelerator |
| 1815 | |
| 1816 | config FB_MBX_DEBUG |
| 1817 | bool "Enable debugging info via debugfs" |
| 1818 | depends on FB_MBX && DEBUG_FS |
| 1819 | default n |
| 1820 | ---help--- |
| 1821 | Enable this if you want debugging information using the debug |
| 1822 | filesystem (debugfs) |
| 1823 | |
| 1824 | If unsure, say N. |
| 1825 | |
York Sun | 9b53a9e | 2008-04-28 02:15:34 -0700 | [diff] [blame] | 1826 | config FB_FSL_DIU |
| 1827 | tristate "Freescale DIU framebuffer support" |
| 1828 | depends on FB && FSL_SOC |
| 1829 | select FB_CFB_FILLRECT |
| 1830 | select FB_CFB_COPYAREA |
| 1831 | select FB_CFB_IMAGEBLIT |
| 1832 | select PPC_LIB_RHEAP |
| 1833 | ---help--- |
| 1834 | Framebuffer driver for the Freescale SoC DIU |
| 1835 | |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 1836 | config FB_W100 |
| 1837 | tristate "W100 frame buffer support" |
Philipp Zabel | e5dd3cb | 2008-07-04 09:59:52 -0700 | [diff] [blame] | 1838 | depends on FB && ARCH_PXA |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 1839 | select FB_CFB_FILLRECT |
| 1840 | select FB_CFB_COPYAREA |
| 1841 | select FB_CFB_IMAGEBLIT |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 1842 | ---help--- |
| 1843 | Frame buffer driver for the w100 as found on the Sharp SL-Cxx series. |
Philipp Zabel | e5dd3cb | 2008-07-04 09:59:52 -0700 | [diff] [blame] | 1844 | It can also drive the w3220 chip found on iPAQ hx4700. |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 1845 | |
| 1846 | This driver is also available as a module ( = code which can be |
| 1847 | inserted and removed from the running kernel whenever you want). The |
YOSHIFUJI Hideaki | 74b4f04 | 2006-01-09 20:53:46 -0800 | [diff] [blame] | 1848 | module will be called w100fb. If you want to compile it as a module, |
Alexander E. Patrakov | 39f5fb3 | 2007-03-16 18:28:43 +0500 | [diff] [blame] | 1849 | say M here and read <file:Documentation/kbuild/modules.txt>. |
Randy Dunlap | ecc41d5 | 2005-11-07 01:00:29 -0800 | [diff] [blame] | 1850 | |
| 1851 | If unsure, say N. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1852 | |
Magnus Damm | cfb4f5d | 2008-07-23 21:31:24 -0700 | [diff] [blame] | 1853 | config FB_SH_MOBILE_LCDC |
| 1854 | tristate "SuperH Mobile LCDC framebuffer support" |
Paul Mundt | 727dc3f | 2009-07-07 10:30:02 +0900 | [diff] [blame] | 1855 | depends on FB && SUPERH && HAVE_CLK |
Magnus Damm | 2540c11 | 2008-12-17 17:29:49 +0900 | [diff] [blame] | 1856 | select FB_SYS_FILLRECT |
| 1857 | select FB_SYS_COPYAREA |
| 1858 | select FB_SYS_IMAGEBLIT |
| 1859 | select FB_SYS_FOPS |
Magnus Damm | 8564557 | 2008-12-19 15:34:41 +0900 | [diff] [blame] | 1860 | select FB_DEFERRED_IO |
Magnus Damm | cfb4f5d | 2008-07-23 21:31:24 -0700 | [diff] [blame] | 1861 | ---help--- |
| 1862 | Frame buffer driver for the on-chip SH-Mobile LCD controller. |
| 1863 | |
Dmitry Baryshkov | b53cde3 | 2008-10-15 22:03:55 -0700 | [diff] [blame] | 1864 | config FB_TMIO |
| 1865 | tristate "Toshiba Mobile IO FrameBuffer support" |
| 1866 | depends on FB && MFD_CORE |
| 1867 | select FB_CFB_FILLRECT |
| 1868 | select FB_CFB_COPYAREA |
| 1869 | select FB_CFB_IMAGEBLIT |
| 1870 | ---help--- |
| 1871 | Frame buffer driver for the Toshiba Mobile IO integrated as found |
| 1872 | on the Sharp SL-6000 series |
| 1873 | |
| 1874 | This driver is also available as a module ( = code which can be |
| 1875 | inserted and removed from the running kernel whenever you want). The |
| 1876 | module will be called tmiofb. If you want to compile it as a module, |
| 1877 | say M here and read <file:Documentation/kbuild/modules.txt>. |
| 1878 | |
| 1879 | If unsure, say N. |
| 1880 | |
| 1881 | config FB_TMIO_ACCELL |
| 1882 | bool "tmiofb acceleration" |
| 1883 | depends on FB_TMIO |
| 1884 | default y |
| 1885 | |
Ben Dooks | ec549a0 | 2009-03-31 15:25:39 -0700 | [diff] [blame] | 1886 | config FB_S3C |
| 1887 | tristate "Samsung S3C framebuffer support" |
| 1888 | depends on FB && ARCH_S3C64XX |
| 1889 | select FB_CFB_FILLRECT |
| 1890 | select FB_CFB_COPYAREA |
| 1891 | select FB_CFB_IMAGEBLIT |
| 1892 | ---help--- |
| 1893 | Frame buffer driver for the built-in FB controller in the Samsung |
| 1894 | SoC line from the S3C2443 onwards, including the S3C2416, S3C2450, |
| 1895 | and the S3C64XX series such as the S3C6400 and S3C6410. |
| 1896 | |
| 1897 | These chips all have the same basic framebuffer design with the |
| 1898 | actual capabilities depending on the chip. For instance the S3C6400 |
| 1899 | and S3C6410 support 4 hardware windows whereas the S3C24XX series |
| 1900 | currently only have two. |
| 1901 | |
| 1902 | Currently the support is only for the S3C6400 and S3C6410 SoCs. |
| 1903 | |
| 1904 | config FB_S3C_DEBUG_REGWRITE |
| 1905 | bool "Debug register writes" |
| 1906 | depends on FB_S3C |
| 1907 | ---help--- |
| 1908 | Show all register writes via printk(KERN_DEBUG) |
| 1909 | |
Arnaud Patard | 20fd576 | 2005-09-09 13:10:07 -0700 | [diff] [blame] | 1910 | config FB_S3C2410 |
| 1911 | tristate "S3C2410 LCD framebuffer support" |
| 1912 | depends on FB && ARCH_S3C2410 |
| 1913 | select FB_CFB_FILLRECT |
| 1914 | select FB_CFB_COPYAREA |
| 1915 | select FB_CFB_IMAGEBLIT |
Arnaud Patard | 20fd576 | 2005-09-09 13:10:07 -0700 | [diff] [blame] | 1916 | ---help--- |
| 1917 | Frame buffer driver for the built-in LCD controller in the Samsung |
| 1918 | S3C2410 processor. |
| 1919 | |
| 1920 | This driver is also available as a module ( = code which can be |
| 1921 | inserted and removed from the running kernel whenever you want). The |
| 1922 | module will be called s3c2410fb. If you want to compile it as a module, |
Alexander E. Patrakov | 39f5fb3 | 2007-03-16 18:28:43 +0500 | [diff] [blame] | 1923 | say M here and read <file:Documentation/kbuild/modules.txt>. |
Arnaud Patard | 20fd576 | 2005-09-09 13:10:07 -0700 | [diff] [blame] | 1924 | |
| 1925 | If unsure, say N. |
| 1926 | config FB_S3C2410_DEBUG |
| 1927 | bool "S3C2410 lcd debug messages" |
| 1928 | depends on FB_S3C2410 |
| 1929 | help |
| 1930 | Turn on debugging messages. Note that you can set/unset at run time |
| 1931 | through sysfs |
| 1932 | |
Ben Dooks | 5fc404e | 2007-02-20 13:58:21 -0800 | [diff] [blame] | 1933 | config FB_SM501 |
| 1934 | tristate "Silicon Motion SM501 framebuffer support" |
| 1935 | depends on FB && MFD_SM501 |
| 1936 | select FB_CFB_FILLRECT |
| 1937 | select FB_CFB_COPYAREA |
| 1938 | select FB_CFB_IMAGEBLIT |
| 1939 | ---help--- |
| 1940 | Frame buffer driver for the CRT and LCD controllers in the Silicon |
| 1941 | Motion SM501. |
| 1942 | |
| 1943 | This driver is also available as a module ( = code which can be |
| 1944 | inserted and removed from the running kernel whenever you want). The |
| 1945 | module will be called sm501fb. If you want to compile it as a module, |
Dirk Hohndel | e403149 | 2007-10-30 13:37:19 -0700 | [diff] [blame] | 1946 | say M here and read <file:Documentation/kbuild/modules.txt>. |
Ben Dooks | 5fc404e | 2007-02-20 13:58:21 -0800 | [diff] [blame] | 1947 | |
| 1948 | If unsure, say N. |
| 1949 | |
| 1950 | |
Vitaly Wool | 36c9366 | 2006-07-03 00:24:19 -0700 | [diff] [blame] | 1951 | config FB_PNX4008_DUM |
| 1952 | tristate "Display Update Module support on Philips PNX4008 board" |
| 1953 | depends on FB && ARCH_PNX4008 |
| 1954 | ---help--- |
| 1955 | Say Y here to enable support for PNX4008 Display Update Module (DUM) |
| 1956 | |
| 1957 | config FB_PNX4008_DUM_RGB |
| 1958 | tristate "RGB Framebuffer support on Philips PNX4008 board" |
| 1959 | depends on FB_PNX4008_DUM |
| 1960 | select FB_CFB_FILLRECT |
| 1961 | select FB_CFB_COPYAREA |
| 1962 | select FB_CFB_IMAGEBLIT |
| 1963 | ---help--- |
| 1964 | Say Y here to enable support for PNX4008 RGB Framebuffer |
| 1965 | |
Paul Mackerras | a3d8998 | 2006-12-10 02:20:42 -0800 | [diff] [blame] | 1966 | config FB_IBM_GXT4500 |
| 1967 | tristate "Framebuffer support for IBM GXT4500P adaptor" |
Randy Dunlap | 0058f47 | 2007-10-16 01:29:35 -0700 | [diff] [blame] | 1968 | depends on FB && PPC |
Paul Mackerras | a3d8998 | 2006-12-10 02:20:42 -0800 | [diff] [blame] | 1969 | select FB_CFB_FILLRECT |
| 1970 | select FB_CFB_COPYAREA |
| 1971 | select FB_CFB_IMAGEBLIT |
| 1972 | ---help--- |
| 1973 | Say Y here to enable support for the IBM GXT4500P display |
| 1974 | adaptor, found on some IBM System P (pSeries) machines. |
| 1975 | |
Geert Uytterhoeven | 310d8c1 | 2007-02-12 00:55:23 -0800 | [diff] [blame] | 1976 | config FB_PS3 |
Geert Uytterhoeven | 9e6b99b | 2007-06-16 08:05:38 +1000 | [diff] [blame] | 1977 | tristate "PS3 GPU framebuffer driver" |
| 1978 | depends on FB && PS3_PS3AV |
Geert Uytterhoeven | 92c4579 | 2007-05-23 13:57:50 -0700 | [diff] [blame] | 1979 | select FB_SYS_FILLRECT |
| 1980 | select FB_SYS_COPYAREA |
| 1981 | select FB_SYS_IMAGEBLIT |
| 1982 | select FB_SYS_FOPS |
Geert Uytterhoeven | 23e9c94 | 2007-07-21 04:37:49 -0700 | [diff] [blame] | 1983 | select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE |
Geert Uytterhoeven | 310d8c1 | 2007-02-12 00:55:23 -0800 | [diff] [blame] | 1984 | ---help--- |
| 1985 | Include support for the virtual frame buffer in the PS3 platform. |
| 1986 | |
| 1987 | config FB_PS3_DEFAULT_SIZE_M |
| 1988 | int "PS3 default frame buffer size (in MiB)" |
| 1989 | depends on FB_PS3 |
Geert Uytterhoeven | 50b2529 | 2007-07-21 04:37:50 -0700 | [diff] [blame] | 1990 | default 9 |
Geert Uytterhoeven | 310d8c1 | 2007-02-12 00:55:23 -0800 | [diff] [blame] | 1991 | ---help--- |
| 1992 | This is the default size (in MiB) of the virtual frame buffer in |
| 1993 | the PS3. |
| 1994 | The default value can be overridden on the kernel command line |
| 1995 | using the "ps3fb" option (e.g. "ps3fb=9M"); |
| 1996 | |
Andrei Konovalov | 147394c | 2007-05-08 00:40:18 -0700 | [diff] [blame] | 1997 | config FB_XILINX |
| 1998 | tristate "Xilinx frame buffer support" |
Michal Simek | 6fa612b | 2009-05-11 15:49:12 +0200 | [diff] [blame] | 1999 | depends on FB && (XILINX_VIRTEX || MICROBLAZE) |
Andrei Konovalov | 147394c | 2007-05-08 00:40:18 -0700 | [diff] [blame] | 2000 | select FB_CFB_FILLRECT |
| 2001 | select FB_CFB_COPYAREA |
| 2002 | select FB_CFB_IMAGEBLIT |
| 2003 | ---help--- |
| 2004 | Include support for the Xilinx ML300/ML403 reference design |
| 2005 | framebuffer. ML300 carries a 640*480 LCD display on the board, |
| 2006 | ML403 uses a standard DB15 VGA connector. |
| 2007 | |
Yoichi Yuasa | 5abe3b4 | 2008-07-23 21:31:40 -0700 | [diff] [blame] | 2008 | config FB_COBALT |
| 2009 | tristate "Cobalt server LCD frame buffer support" |
| 2010 | depends on FB && MIPS_COBALT |
| 2011 | |
Nobuhiro Iwamatsu | 4a25e41 | 2008-07-23 21:31:46 -0700 | [diff] [blame] | 2012 | config FB_SH7760 |
Nobuhiro Iwamatsu | 5c72f30 | 2008-11-21 14:35:29 +0900 | [diff] [blame] | 2013 | bool "SH7760/SH7763/SH7720/SH7721 LCDC support" |
| 2014 | depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \ |
| 2015 | || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721) |
| 2016 | select FB_CFB_FILLRECT |
| 2017 | select FB_CFB_COPYAREA |
| 2018 | select FB_CFB_IMAGEBLIT |
| 2019 | ---help--- |
| 2020 | Support for the SH7760/SH7763/SH7720/SH7721 integrated |
| 2021 | (D)STN/TFT LCD Controller. |
| 2022 | Supports display resolutions up to 1024x1024 pixel, grayscale and |
| 2023 | color operation, with depths ranging from 1 bpp to 8 bpp monochrome |
| 2024 | and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for |
| 2025 | panels <= 320 pixel horizontal resolution. |
Nobuhiro Iwamatsu | 4a25e41 | 2008-07-23 21:31:46 -0700 | [diff] [blame] | 2026 | |
Sudhakar Rajashekhara | 4ed824d | 2009-09-22 16:47:06 -0700 | [diff] [blame] | 2027 | config FB_DA8XX |
| 2028 | tristate "DA8xx/OMAP-L1xx Framebuffer support" |
| 2029 | depends on FB && ARCH_DAVINCI_DA8XX |
| 2030 | select FB_CFB_FILLRECT |
| 2031 | select FB_CFB_COPYAREA |
| 2032 | select FB_CFB_IMAGEBLIT |
| 2033 | ---help--- |
| 2034 | This is the frame buffer device driver for the TI LCD controller |
| 2035 | found on DA8xx/OMAP-L1xx SoCs. |
| 2036 | If unsure, say N. |
| 2037 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2038 | config FB_VIRTUAL |
| 2039 | tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)" |
| 2040 | depends on FB |
Antonino A. Daplas | 87b4884 | 2007-05-08 00:39:01 -0700 | [diff] [blame] | 2041 | select FB_SYS_FILLRECT |
| 2042 | select FB_SYS_COPYAREA |
| 2043 | select FB_SYS_IMAGEBLIT |
Antonino A. Daplas | 52102c0 | 2007-05-08 00:39:07 -0700 | [diff] [blame] | 2044 | select FB_SYS_FOPS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2045 | ---help--- |
| 2046 | This is a `virtual' frame buffer device. It operates on a chunk of |
| 2047 | unswappable kernel memory instead of on the memory of a graphics |
| 2048 | board. This means you cannot see any output sent to this frame |
| 2049 | buffer device, while it does consume precious memory. The main use |
| 2050 | of this frame buffer device is testing and debugging the frame |
| 2051 | buffer subsystem. Do NOT enable it for normal systems! To protect |
| 2052 | the innocent, it has to be enabled explicitly at boot time using the |
| 2053 | kernel option `video=vfb:'. |
| 2054 | |
| 2055 | To compile this driver as a module, choose M here: the |
Mike Frysinger | 66cf751 | 2006-10-03 01:14:41 -0700 | [diff] [blame] | 2056 | module will be called vfb. In order to load it, you must use |
| 2057 | the vfb_enable=1 option. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2058 | |
| 2059 | If unsure, say N. |
James Simmons | e0e34ef | 2007-02-10 14:15:43 +0000 | [diff] [blame] | 2060 | |
Markus Armbruster | 4ee36dc | 2008-04-02 10:54:07 -0700 | [diff] [blame] | 2061 | config XEN_FBDEV_FRONTEND |
| 2062 | tristate "Xen virtual frame buffer support" |
| 2063 | depends on FB && XEN |
| 2064 | select FB_SYS_FILLRECT |
| 2065 | select FB_SYS_COPYAREA |
| 2066 | select FB_SYS_IMAGEBLIT |
| 2067 | select FB_SYS_FOPS |
| 2068 | select FB_DEFERRED_IO |
Konrad Rzeszutek Wilk | ba69ea4 | 2009-10-08 13:23:08 -0400 | [diff] [blame] | 2069 | select XEN_XENBUS_FRONTEND |
Markus Armbruster | 4ee36dc | 2008-04-02 10:54:07 -0700 | [diff] [blame] | 2070 | default y |
| 2071 | help |
| 2072 | This driver implements the front-end of the Xen virtual |
| 2073 | frame buffer driver. It communicates with a back-end |
| 2074 | in another domain. |
| 2075 | |
Jaya Kumar | e935508 | 2008-08-19 11:17:55 +0100 | [diff] [blame] | 2076 | config FB_METRONOME |
| 2077 | tristate "E-Ink Metronome/8track controller support" |
| 2078 | depends on FB |
| 2079 | select FB_SYS_FILLRECT |
| 2080 | select FB_SYS_COPYAREA |
| 2081 | select FB_SYS_IMAGEBLIT |
| 2082 | select FB_SYS_FOPS |
| 2083 | select FB_DEFERRED_IO |
| 2084 | help |
| 2085 | This driver implements support for the E-Ink Metronome |
| 2086 | controller. The pre-release name for this device was 8track |
| 2087 | and could also have been called by some vendors as PVI-nnnn. |
| 2088 | |
Anatolij Gustschin | 17a1217 | 2008-11-06 12:53:29 -0800 | [diff] [blame] | 2089 | config FB_MB862XX |
| 2090 | tristate "Fujitsu MB862xx GDC support" |
| 2091 | depends on FB |
| 2092 | select FB_CFB_FILLRECT |
| 2093 | select FB_CFB_COPYAREA |
| 2094 | select FB_CFB_IMAGEBLIT |
| 2095 | ---help--- |
| 2096 | Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers. |
| 2097 | |
| 2098 | config FB_MB862XX_PCI_GDC |
| 2099 | bool "Carmine/Coral-P(A) GDC" |
| 2100 | depends on PCI && FB_MB862XX |
| 2101 | ---help--- |
| 2102 | This enables framebuffer support for Fujitsu Carmine/Coral-P(A) |
| 2103 | PCI graphics controller devices. |
| 2104 | |
| 2105 | config FB_MB862XX_LIME |
| 2106 | bool "Lime GDC" |
| 2107 | depends on FB_MB862XX |
| 2108 | depends on OF && !FB_MB862XX_PCI_GDC |
Julian Calaby | 336e747 | 2009-06-16 15:34:29 -0700 | [diff] [blame] | 2109 | depends on PPC |
Anatolij Gustschin | 17a1217 | 2008-11-06 12:53:29 -0800 | [diff] [blame] | 2110 | select FB_FOREIGN_ENDIAN |
| 2111 | select FB_LITTLE_ENDIAN |
| 2112 | ---help--- |
| 2113 | Framebuffer support for Fujitsu Lime GDC on host CPU bus. |
| 2114 | |
Ryan Mallon | 88017bd | 2009-09-22 16:47:09 -0700 | [diff] [blame] | 2115 | config FB_EP93XX |
| 2116 | tristate "EP93XX frame buffer support" |
| 2117 | depends on FB && ARCH_EP93XX |
| 2118 | select FB_CFB_FILLRECT |
| 2119 | select FB_CFB_COPYAREA |
| 2120 | select FB_CFB_IMAGEBLIT |
| 2121 | ---help--- |
| 2122 | Framebuffer driver for the Cirrus Logic EP93XX series of processors. |
| 2123 | This driver is also available as a module. The module will be called |
| 2124 | ep93xx-fb. |
| 2125 | |
Anatolij Gustschin | 17a1217 | 2008-11-06 12:53:29 -0800 | [diff] [blame] | 2126 | config FB_PRE_INIT_FB |
| 2127 | bool "Don't reinitialize, use bootloader's GDC/Display configuration" |
Guennadi Liakhovetski | 93f40e6 | 2009-11-11 14:26:47 -0800 | [diff] [blame] | 2128 | depends on FB && FB_MB862XX_LIME |
Anatolij Gustschin | 17a1217 | 2008-11-06 12:53:29 -0800 | [diff] [blame] | 2129 | ---help--- |
| 2130 | Select this option if display contents should be inherited as set by |
| 2131 | the bootloader. |
| 2132 | |
Pavel Machek | d480ace | 2009-09-22 16:47:03 -0700 | [diff] [blame] | 2133 | config FB_MSM |
Pavel Machek | 4e00dc7 | 2009-12-08 11:10:28 -0800 | [diff] [blame] | 2134 | tristate "MSM Framebuffer support" |
Pavel Machek | d480ace | 2009-09-22 16:47:03 -0700 | [diff] [blame] | 2135 | depends on FB && ARCH_MSM |
| 2136 | select FB_CFB_FILLRECT |
| 2137 | select FB_CFB_COPYAREA |
| 2138 | select FB_CFB_IMAGEBLIT |
| 2139 | default y |
| 2140 | |
Guennadi Liakhovetski | 86528da | 2009-01-21 10:32:34 -0700 | [diff] [blame] | 2141 | config FB_MX3 |
Guennadi Liakhovetski | 6e1588c | 2009-02-26 21:34:28 +0100 | [diff] [blame] | 2142 | tristate "MX3 Framebuffer support" |
| 2143 | depends on FB && MX3_IPU |
| 2144 | select FB_CFB_FILLRECT |
| 2145 | select FB_CFB_COPYAREA |
| 2146 | select FB_CFB_IMAGEBLIT |
| 2147 | default y |
| 2148 | help |
| 2149 | This is a framebuffer device for the i.MX31 LCD Controller. So |
| 2150 | far only synchronous displays are supported. If you plan to use |
| 2151 | an LCD display with your i.MX31 system, say Y here. |
Guennadi Liakhovetski | 86528da | 2009-01-21 10:32:34 -0700 | [diff] [blame] | 2152 | |
Jaya Kumar | 0d4ff4d | 2009-01-01 17:49:19 +0100 | [diff] [blame] | 2153 | config FB_BROADSHEET |
| 2154 | tristate "E-Ink Broadsheet/Epson S1D13521 controller support" |
| 2155 | depends on FB |
| 2156 | select FB_SYS_FILLRECT |
| 2157 | select FB_SYS_COPYAREA |
| 2158 | select FB_SYS_IMAGEBLIT |
| 2159 | select FB_SYS_FOPS |
| 2160 | select FB_DEFERRED_IO |
| 2161 | help |
| 2162 | This driver implements support for the E-Ink Broadsheet |
| 2163 | controller. The release name for this device was Epson S1D13521 |
| 2164 | and could also have been called by other names when coupled with |
| 2165 | a bridge adapter. |
| 2166 | |
Randy Dunlap | f08f389 | 2007-10-29 14:37:16 -0700 | [diff] [blame] | 2167 | source "drivers/video/omap/Kconfig" |
Tomi Valkeinen | afedec1 | 2009-08-07 12:01:55 +0300 | [diff] [blame] | 2168 | source "drivers/video/omap2/Kconfig" |
Randy Dunlap | 0058f47 | 2007-10-16 01:29:35 -0700 | [diff] [blame] | 2169 | |
Randy Dunlap | 179b025 | 2007-10-16 01:29:39 -0700 | [diff] [blame] | 2170 | source "drivers/video/backlight/Kconfig" |
| 2171 | source "drivers/video/display/Kconfig" |
| 2172 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2173 | if VT |
| 2174 | source "drivers/video/console/Kconfig" |
| 2175 | endif |
| 2176 | |
| 2177 | if FB || SGI_NEWPORT_CONSOLE |
| 2178 | source "drivers/video/logo/Kconfig" |
| 2179 | endif |
| 2180 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2181 | endmenu |