| /* |
| * Copyright (C) 2010 Marvell International Ltd. |
| * Zhangfei Gao <zhangfei.gao@marvell.com> |
| * Kevin Wang <dwang4@marvell.com> |
| * Mingwei Wang <mwwang@marvell.com> |
| * Philip Rakity <prakity@marvell.com> |
| * Mark Brown <markb@marvell.com> |
| * |
| * This software is licensed under the terms of the GNU General Public |
| * License version 2, as published by the Free Software Foundation, and |
| * may be copied, distributed, and modified under those terms. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| #include <linux/err.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/clk.h> |
| #include <linux/io.h> |
| #include <linux/gpio.h> |
| #include <linux/mmc/card.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/slot-gpio.h> |
| #include <linux/platform_data/pxa_sdhci.h> |
| #include <linux/slab.h> |
| #include <linux/delay.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_gpio.h> |
| |
| #include "sdhci.h" |
| #include "sdhci-pltfm.h" |
| |
| #define SD_CLOCK_BURST_SIZE_SETUP 0x10A |
| #define SDCLK_SEL 0x100 |
| #define SDCLK_DELAY_SHIFT 9 |
| #define SDCLK_DELAY_MASK 0x1f |
| |
| #define SD_CFG_FIFO_PARAM 0x100 |
| #define SDCFG_GEN_PAD_CLK_ON (1<<6) |
| #define SDCFG_GEN_PAD_CLK_CNT_MASK 0xFF |
| #define SDCFG_GEN_PAD_CLK_CNT_SHIFT 24 |
| |
| #define SD_SPI_MODE 0x108 |
| #define SD_CE_ATA_1 0x10C |
| |
| #define SD_CE_ATA_2 0x10E |
| #define SDCE_MISC_INT (1<<2) |
| #define SDCE_MISC_INT_EN (1<<1) |
| |
| static void pxav3_set_private_registers(struct sdhci_host *host, u8 mask) |
| { |
| struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc)); |
| struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; |
| |
| if (mask == SDHCI_RESET_ALL) { |
| /* |
| * tune timing of read data/command when crc error happen |
| * no performance impact |
| */ |
| if (pdata && 0 != pdata->clk_delay_cycles) { |
| u16 tmp; |
| |
| tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); |
| tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK) |
| << SDCLK_DELAY_SHIFT; |
| tmp |= SDCLK_SEL; |
| writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); |
| } |
| } |
| } |
| |
| #define MAX_WAIT_COUNT 5 |
| static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_pxa *pxa = pltfm_host->priv; |
| u16 tmp; |
| int count; |
| |
| if (pxa->power_mode == MMC_POWER_UP |
| && power_mode == MMC_POWER_ON) { |
| |
| dev_dbg(mmc_dev(host->mmc), |
| "%s: slot->power_mode = %d," |
| "ios->power_mode = %d\n", |
| __func__, |
| pxa->power_mode, |
| power_mode); |
| |
| /* set we want notice of when 74 clocks are sent */ |
| tmp = readw(host->ioaddr + SD_CE_ATA_2); |
| tmp |= SDCE_MISC_INT_EN; |
| writew(tmp, host->ioaddr + SD_CE_ATA_2); |
| |
| /* start sending the 74 clocks */ |
| tmp = readw(host->ioaddr + SD_CFG_FIFO_PARAM); |
| tmp |= SDCFG_GEN_PAD_CLK_ON; |
| writew(tmp, host->ioaddr + SD_CFG_FIFO_PARAM); |
| |
| /* slowest speed is about 100KHz or 10usec per clock */ |
| udelay(740); |
| count = 0; |
| |
| while (count++ < MAX_WAIT_COUNT) { |
| if ((readw(host->ioaddr + SD_CE_ATA_2) |
| & SDCE_MISC_INT) == 0) |
| break; |
| udelay(10); |
| } |
| |
| if (count == MAX_WAIT_COUNT) |
| dev_warn(mmc_dev(host->mmc), "74 clock interrupt not cleared\n"); |
| |
| /* clear the interrupt bit if posted */ |
| tmp = readw(host->ioaddr + SD_CE_ATA_2); |
| tmp |= SDCE_MISC_INT; |
| writew(tmp, host->ioaddr + SD_CE_ATA_2); |
| } |
| pxa->power_mode = power_mode; |
| } |
| |
| static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) |
| { |
| u16 ctrl_2; |
| |
| /* |
| * Set V18_EN -- UHS modes do not work without this. |
| * does not change signaling voltage |
| */ |
| ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); |
| |
| /* Select Bus Speed Mode for host */ |
| ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; |
| switch (uhs) { |
| case MMC_TIMING_UHS_SDR12: |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR12; |
| break; |
| case MMC_TIMING_UHS_SDR25: |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR25; |
| break; |
| case MMC_TIMING_UHS_SDR50: |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180; |
| break; |
| case MMC_TIMING_UHS_SDR104: |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180; |
| break; |
| case MMC_TIMING_UHS_DDR50: |
| ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180; |
| break; |
| } |
| |
| sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); |
| dev_dbg(mmc_dev(host->mmc), |
| "%s uhs = %d, ctrl_2 = %04X\n", |
| __func__, uhs, ctrl_2); |
| |
| return 0; |
| } |
| |
| static u32 pxav3_get_max_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| |
| return clk_get_rate(pltfm_host->clk); |
| } |
| |
| static struct sdhci_ops pxav3_sdhci_ops = { |
| .platform_reset_exit = pxav3_set_private_registers, |
| .set_uhs_signaling = pxav3_set_uhs_signaling, |
| .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, |
| .get_max_clock = pxav3_get_max_clock, |
| }; |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id sdhci_pxav3_of_match[] = { |
| { |
| .compatible = "mrvl,pxav3-mmc", |
| }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, sdhci_pxav3_of_match); |
| |
| static struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) |
| { |
| struct sdhci_pxa_platdata *pdata; |
| struct device_node *np = dev->of_node; |
| u32 bus_width; |
| u32 clk_delay_cycles; |
| enum of_gpio_flags gpio_flags; |
| |
| pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); |
| if (!pdata) |
| return NULL; |
| |
| if (of_find_property(np, "non-removable", NULL)) |
| pdata->flags |= PXA_FLAG_CARD_PERMANENT; |
| |
| of_property_read_u32(np, "bus-width", &bus_width); |
| if (bus_width == 8) |
| pdata->flags |= PXA_FLAG_SD_8_BIT_CAPABLE_SLOT; |
| |
| of_property_read_u32(np, "mrvl,clk-delay-cycles", &clk_delay_cycles); |
| if (clk_delay_cycles > 0) |
| pdata->clk_delay_cycles = clk_delay_cycles; |
| |
| pdata->ext_cd_gpio = of_get_named_gpio_flags(np, "cd-gpios", 0, &gpio_flags); |
| if (gpio_flags != OF_GPIO_ACTIVE_LOW) |
| pdata->host_caps2 |= MMC_CAP2_CD_ACTIVE_HIGH; |
| |
| return pdata; |
| } |
| #else |
| static inline struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) |
| { |
| return NULL; |
| } |
| #endif |
| |
| static int sdhci_pxav3_probe(struct platform_device *pdev) |
| { |
| struct sdhci_pltfm_host *pltfm_host; |
| struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; |
| struct device *dev = &pdev->dev; |
| struct sdhci_host *host = NULL; |
| struct sdhci_pxa *pxa = NULL; |
| const struct of_device_id *match; |
| |
| int ret; |
| struct clk *clk; |
| |
| pxa = kzalloc(sizeof(struct sdhci_pxa), GFP_KERNEL); |
| if (!pxa) |
| return -ENOMEM; |
| |
| host = sdhci_pltfm_init(pdev, NULL); |
| if (IS_ERR(host)) { |
| kfree(pxa); |
| return PTR_ERR(host); |
| } |
| pltfm_host = sdhci_priv(host); |
| pltfm_host->priv = pxa; |
| |
| clk = clk_get(dev, NULL); |
| if (IS_ERR(clk)) { |
| dev_err(dev, "failed to get io clock\n"); |
| ret = PTR_ERR(clk); |
| goto err_clk_get; |
| } |
| pltfm_host->clk = clk; |
| clk_prepare_enable(clk); |
| |
| host->quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL |
| | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
| | SDHCI_QUIRK_32BIT_ADMA_SIZE |
| | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; |
| |
| /* enable 1/8V DDR capable */ |
| host->mmc->caps |= MMC_CAP_1_8V_DDR; |
| |
| match = of_match_device(of_match_ptr(sdhci_pxav3_of_match), &pdev->dev); |
| if (match) |
| pdata = pxav3_get_mmc_pdata(dev); |
| |
| if (pdata) { |
| if (pdata->flags & PXA_FLAG_CARD_PERMANENT) { |
| /* on-chip device */ |
| host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION; |
| host->mmc->caps |= MMC_CAP_NONREMOVABLE; |
| } |
| |
| /* If slot design supports 8 bit data, indicate this to MMC. */ |
| if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT) |
| host->mmc->caps |= MMC_CAP_8_BIT_DATA; |
| |
| if (pdata->quirks) |
| host->quirks |= pdata->quirks; |
| if (pdata->quirks2) |
| host->quirks2 |= pdata->quirks2; |
| if (pdata->host_caps) |
| host->mmc->caps |= pdata->host_caps; |
| if (pdata->host_caps2) |
| host->mmc->caps2 |= pdata->host_caps2; |
| if (pdata->pm_caps) |
| host->mmc->pm_caps |= pdata->pm_caps; |
| |
| if (gpio_is_valid(pdata->ext_cd_gpio)) { |
| ret = mmc_gpio_request_cd(host->mmc, pdata->ext_cd_gpio); |
| if (ret) { |
| dev_err(mmc_dev(host->mmc), |
| "failed to allocate card detect gpio\n"); |
| goto err_cd_req; |
| } |
| } |
| } |
| |
| host->ops = &pxav3_sdhci_ops; |
| |
| sdhci_get_of_property(pdev); |
| |
| ret = sdhci_add_host(host); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to add host\n"); |
| goto err_add_host; |
| } |
| |
| platform_set_drvdata(pdev, host); |
| |
| return 0; |
| |
| err_add_host: |
| clk_disable_unprepare(clk); |
| clk_put(clk); |
| mmc_gpio_free_cd(host->mmc); |
| err_cd_req: |
| err_clk_get: |
| sdhci_pltfm_free(pdev); |
| kfree(pxa); |
| return ret; |
| } |
| |
| static int sdhci_pxav3_remove(struct platform_device *pdev) |
| { |
| struct sdhci_host *host = platform_get_drvdata(pdev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_pxa *pxa = pltfm_host->priv; |
| struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; |
| |
| sdhci_remove_host(host, 1); |
| |
| clk_disable_unprepare(pltfm_host->clk); |
| clk_put(pltfm_host->clk); |
| |
| if (gpio_is_valid(pdata->ext_cd_gpio)) |
| mmc_gpio_free_cd(host->mmc); |
| |
| sdhci_pltfm_free(pdev); |
| kfree(pxa); |
| |
| platform_set_drvdata(pdev, NULL); |
| |
| return 0; |
| } |
| |
| static struct platform_driver sdhci_pxav3_driver = { |
| .driver = { |
| .name = "sdhci-pxav3", |
| #ifdef CONFIG_OF |
| .of_match_table = sdhci_pxav3_of_match, |
| #endif |
| .owner = THIS_MODULE, |
| .pm = SDHCI_PLTFM_PMOPS, |
| }, |
| .probe = sdhci_pxav3_probe, |
| .remove = sdhci_pxav3_remove, |
| }; |
| |
| module_platform_driver(sdhci_pxav3_driver); |
| |
| MODULE_DESCRIPTION("SDHCI driver for pxav3"); |
| MODULE_AUTHOR("Marvell International Ltd."); |
| MODULE_LICENSE("GPL v2"); |
| |