blob: db8963f5fbcec11988390b32e02a693c787e2727 [file] [log] [blame]
/*
* OHCI HCD (Host Controller Driver) for USB.
*
* Copyright (C) 2004 SAN People (Pty) Ltd.
* Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
*
* AT91 Bus Glue
*
* Based on fragments of 2.4 driver by Rick Bronson.
* Based on ohci-omap.c
*
* This file is licenced under the GPL.
*/
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
#include <mach/hardware.h>
#include <asm/gpio.h>
#include <mach/board.h>
#include <mach/cpu.h>
#ifndef CONFIG_ARCH_AT91
#error "CONFIG_ARCH_AT91 must be defined."
#endif
/* interface and function clocks; sometimes also an AHB clock */
static struct clk *iclk, *fclk, *hclk;
static int clocked;
extern int usb_disabled(void);
/*-------------------------------------------------------------------------*/
static void at91_start_clock(void)
{
clk_enable(hclk);
clk_enable(iclk);
clk_enable(fclk);
clocked = 1;
}
static void at91_stop_clock(void)
{
clk_disable(fclk);
clk_disable(iclk);
clk_disable(hclk);
clocked = 0;
}
static void at91_start_hc(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_regs __iomem *regs = hcd->regs;
dev_dbg(&pdev->dev, "start\n");
/*
* Start the USB clocks.
*/
at91_start_clock();
/*
* The USB host controller must remain in reset.
*/
writel(0, &regs->control);
}
static void at91_stop_hc(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_regs __iomem *regs = hcd->regs;
dev_dbg(&pdev->dev, "stop\n");
/*
* Put the USB host controller into reset.
*/
writel(0, &regs->control);
/*
* Stop the USB clocks.
*/
at91_stop_clock();
}
/*-------------------------------------------------------------------------*/
static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *);
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
/**
* usb_hcd_at91_probe - initialize AT91-based HCDs
* Context: !in_interrupt()
*
* Allocates basic resources for this USB host controller, and
* then invokes the start() method for the HCD associated with it
* through the hotplug entry's driver_data.
*/
static int usb_hcd_at91_probe(const struct hc_driver *driver,
struct platform_device *pdev)
{
int retval;
struct usb_hcd *hcd = NULL;
if (pdev->num_resources != 2) {
pr_debug("hcd probe: invalid num_resources");
return -ENODEV;
}
if ((pdev->resource[0].flags != IORESOURCE_MEM)
|| (pdev->resource[1].flags != IORESOURCE_IRQ)) {
pr_debug("hcd probe: invalid resource type\n");
return -ENODEV;
}
hcd = usb_create_hcd(driver, &pdev->dev, "at91");
if (!hcd)
return -ENOMEM;
hcd->rsrc_start = pdev->resource[0].start;
hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed\n");
retval = -EBUSY;
goto err1;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed\n");
retval = -EIO;
goto err2;
}
iclk = clk_get(&pdev->dev, "ohci_clk");
if (IS_ERR(iclk)) {
dev_err(&pdev->dev, "failed to get ohci_clk\n");
retval = PTR_ERR(iclk);
goto err3;
}
fclk = clk_get(&pdev->dev, "uhpck");
if (IS_ERR(fclk)) {
dev_err(&pdev->dev, "failed to get uhpck\n");
retval = PTR_ERR(fclk);
goto err4;
}
hclk = clk_get(&pdev->dev, "hclk");
if (IS_ERR(hclk)) {
dev_err(&pdev->dev, "failed to get hclk\n");
retval = PTR_ERR(hclk);
goto err5;
}
at91_start_hc(pdev);
ohci_hcd_init(hcd_to_ohci(hcd));
retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_SHARED);
if (retval == 0)
return retval;
/* Error handling */
at91_stop_hc(pdev);
clk_put(hclk);
err5:
clk_put(fclk);
err4:
clk_put(iclk);
err3:
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
usb_put_hcd(hcd);
return retval;
}
/* may be called with controller, bus, and devices active */
/**
* usb_hcd_at91_remove - shutdown processing for AT91-based HCDs
* @dev: USB Host Controller being removed
* Context: !in_interrupt()
*
* Reverses the effect of usb_hcd_at91_probe(), first invoking
* the HCD's stop() method. It is always called from a thread
* context, "rmmod" or something similar.
*
*/
static void usb_hcd_at91_remove(struct usb_hcd *hcd,
struct platform_device *pdev)
{
usb_remove_hcd(hcd);
at91_stop_hc(pdev);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
clk_put(hclk);
clk_put(fclk);
clk_put(iclk);
fclk = iclk = hclk = NULL;
dev_set_drvdata(&pdev->dev, NULL);
}
/*-------------------------------------------------------------------------*/
static int __devinit
ohci_at91_start (struct usb_hcd *hcd)
{
struct at91_usbh_data *board = hcd->self.controller->platform_data;
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int ret;
if ((ret = ohci_init(ohci)) < 0)
return ret;
ohci->num_ports = board->ports;
if ((ret = ohci_run(ohci)) < 0) {
err("can't start %s", hcd->self.bus_name);
ohci_stop(hcd);
return ret;
}
return 0;
}
static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable)
{
if (port < 0 || port >= 2)
return;
if (!gpio_is_valid(pdata->vbus_pin[port]))
return;
gpio_set_value(pdata->vbus_pin[port],
!pdata->vbus_pin_active_low[port] ^ enable);
}
static int ohci_at91_usb_get_power(struct at91_usbh_data *pdata, int port)
{
if (port < 0 || port >= 2)
return -EINVAL;
if (!gpio_is_valid(pdata->vbus_pin[port]))
return -EINVAL;
return gpio_get_value(pdata->vbus_pin[port]) ^
!pdata->vbus_pin_active_low[port];
}
/*
* Update the status data from the hub with the over-current indicator change.
*/
static int ohci_at91_hub_status_data(struct usb_hcd *hcd, char *buf)
{
struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
int length = ohci_hub_status_data(hcd, buf);
int port;
for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
if (pdata->overcurrent_changed[port]) {
if (! length)
length = 1;
buf[0] |= 1 << (port + 1);
}
}
return length;
}
/*
* Look at the control requests to the root hub and see if we need to override.
*/
static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u16 wIndex, char *buf, u16 wLength)
{
struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
struct usb_hub_descriptor *desc;
int ret = -EINVAL;
u32 *data = (u32 *)buf;
dev_dbg(hcd->self.controller,
"ohci_at91_hub_control(%p,0x%04x,0x%04x,0x%04x,%p,%04x)\n",
hcd, typeReq, wValue, wIndex, buf, wLength);
switch (typeReq) {
case SetPortFeature:
if (wValue == USB_PORT_FEAT_POWER) {
dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
ohci_at91_usb_set_power(pdata, wIndex - 1, 1);
goto out;
}
break;
case ClearPortFeature:
switch (wValue) {
case USB_PORT_FEAT_C_OVER_CURRENT:
dev_dbg(hcd->self.controller,
"ClearPortFeature: C_OVER_CURRENT\n");
if (wIndex == 1 || wIndex == 2) {
pdata->overcurrent_changed[wIndex-1] = 0;
pdata->overcurrent_status[wIndex-1] = 0;
}
goto out;
case USB_PORT_FEAT_OVER_CURRENT:
dev_dbg(hcd->self.controller,
"ClearPortFeature: OVER_CURRENT\n");
if (wIndex == 1 || wIndex == 2) {
pdata->overcurrent_status[wIndex-1] = 0;
}
goto out;
case USB_PORT_FEAT_POWER:
dev_dbg(hcd->self.controller,
"ClearPortFeature: POWER\n");
if (wIndex == 1 || wIndex == 2) {
ohci_at91_usb_set_power(pdata, wIndex - 1, 0);
return 0;
}
}
break;
}
ret = ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
if (ret)
goto out;
switch (typeReq) {
case GetHubDescriptor:
/* update the hub's descriptor */
desc = (struct usb_hub_descriptor *)buf;
dev_dbg(hcd->self.controller, "wHubCharacteristics 0x%04x\n",
desc->wHubCharacteristics);
/* remove the old configurations for power-switching, and
* over-current protection, and insert our new configuration
*/
desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_LPSM);
desc->wHubCharacteristics |= cpu_to_le16(0x0001);
if (pdata->overcurrent_supported) {
desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_OCPM);
desc->wHubCharacteristics |= cpu_to_le16(0x0008|0x0001);
}
dev_dbg(hcd->self.controller, "wHubCharacteristics after 0x%04x\n",
desc->wHubCharacteristics);
return ret;
case GetPortStatus:
/* check port status */
dev_dbg(hcd->self.controller, "GetPortStatus(%d)\n", wIndex);
if (wIndex == 1 || wIndex == 2) {
if (! ohci_at91_usb_get_power(pdata, wIndex-1)) {
*data &= ~cpu_to_le32(RH_PS_PPS);
}
if (pdata->overcurrent_changed[wIndex-1]) {
*data |= cpu_to_le32(RH_PS_OCIC);
}
if (pdata->overcurrent_status[wIndex-1]) {
*data |= cpu_to_le32(RH_PS_POCI);
}
}
}
out:
return ret;
}
/*-------------------------------------------------------------------------*/
static const struct hc_driver ohci_at91_hc_driver = {
.description = hcd_name,
.product_desc = "AT91 OHCI",
.hcd_priv_size = sizeof(struct ohci_hcd),
/*
* generic hardware linkage
*/
.irq = ohci_irq,
.flags = HCD_USB11 | HCD_MEMORY,
/*
* basic lifecycle operations
*/
.start = ohci_at91_start,
.stop = ohci_stop,
.shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
*/
.urb_enqueue = ohci_urb_enqueue,
.urb_dequeue = ohci_urb_dequeue,
.endpoint_disable = ohci_endpoint_disable,
/*
* scheduling support
*/
.get_frame_number = ohci_get_frame,
/*
* root hub support
*/
.hub_status_data = ohci_at91_hub_status_data,
.hub_control = ohci_at91_hub_control,
#ifdef CONFIG_PM
.bus_suspend = ohci_bus_suspend,
.bus_resume = ohci_bus_resume,
#endif
.start_port_reset = ohci_start_port_reset,
};
/*-------------------------------------------------------------------------*/
static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
{
struct platform_device *pdev = data;
struct at91_usbh_data *pdata = pdev->dev.platform_data;
int val, gpio, port;
/* From the GPIO notifying the over-current situation, find
* out the corresponding port */
for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) {
gpio = pdata->overcurrent_pin[port];
break;
}
}
if (port == ARRAY_SIZE(pdata->overcurrent_pin)) {
dev_err(& pdev->dev, "overcurrent interrupt from unknown GPIO\n");
return IRQ_HANDLED;
}
val = gpio_get_value(gpio);
/* When notified of an over-current situation, disable power
on the corresponding port, and mark this port in
over-current. */
if (! val) {
ohci_at91_usb_set_power(pdata, port, 0);
pdata->overcurrent_status[port] = 1;
pdata->overcurrent_changed[port] = 1;
}
dev_dbg(& pdev->dev, "overcurrent situation %s\n",
val ? "exited" : "notified");
return IRQ_HANDLED;
}
#ifdef CONFIG_OF
static const struct of_device_id at91_ohci_dt_ids[] = {
{ .compatible = "atmel,at91rm9200-ohci" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, at91_ohci_dt_ids);
static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32);
static int __devinit ohci_at91_of_init(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
int i, ret, gpio;
enum of_gpio_flags flags;
struct at91_usbh_data *pdata;
u32 ports;
if (!np)
return 0;
/* Right now device-tree probed devices don't get dma_mask set.
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
pdev->dev.dma_mask = &at91_ohci_dma_mask;
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
if (!of_property_read_u32(np, "num-ports", &ports))
pdata->ports = ports;
for (i = 0; i < 2; i++) {
gpio = of_get_named_gpio_flags(np, "atmel,vbus-gpio", i, &flags);
pdata->vbus_pin[i] = gpio;
if (!gpio_is_valid(gpio))
continue;
pdata->vbus_pin_active_low[i] = flags & OF_GPIO_ACTIVE_LOW;
ret = gpio_request(gpio, "ohci_vbus");
if (ret) {
dev_warn(&pdev->dev, "can't request vbus gpio %d", gpio);
continue;
}
ret = gpio_direction_output(gpio, !(flags & OF_GPIO_ACTIVE_LOW) ^ 1);
if (ret)
dev_warn(&pdev->dev, "can't put vbus gpio %d as output %d",
!(flags & OF_GPIO_ACTIVE_LOW) ^ 1, gpio);
}
for (i = 0; i < 2; i++) {
gpio = of_get_named_gpio_flags(np, "atmel,oc-gpio", i, &flags);
pdata->overcurrent_pin[i] = gpio;
if (!gpio_is_valid(gpio))
continue;
ret = gpio_request(gpio, "ohci_overcurrent");
if (ret) {
dev_err(&pdev->dev, "can't request overcurrent gpio %d", gpio);
continue;
}
ret = gpio_direction_input(gpio);
if (ret) {
dev_err(&pdev->dev, "can't configure overcurrent gpio %d as input", gpio);
continue;
}
ret = request_irq(gpio_to_irq(gpio),
ohci_hcd_at91_overcurrent_irq,
IRQF_SHARED, "ohci_overcurrent", pdev);
if (ret) {
gpio_free(gpio);
dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n");
}
}
pdev->dev.platform_data = pdata;
return 0;
}
#else
static int __devinit ohci_at91_of_init(struct platform_device *pdev)
{
return 0;
}
#endif
/*-------------------------------------------------------------------------*/
static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
{
struct at91_usbh_data *pdata;
int i;
i = ohci_at91_of_init(pdev);
if (i)
return i;
pdata = pdev->dev.platform_data;
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
gpio_request(pdata->vbus_pin[i], "ohci_vbus");
ohci_at91_usb_set_power(pdata, i, 1);
}
for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
int ret;
if (!gpio_is_valid(pdata->overcurrent_pin[i]))
continue;
gpio_request(pdata->overcurrent_pin[i], "ohci_overcurrent");
ret = request_irq(gpio_to_irq(pdata->overcurrent_pin[i]),
ohci_hcd_at91_overcurrent_irq,
IRQF_SHARED, "ohci_overcurrent", pdev);
if (ret) {
gpio_free(pdata->overcurrent_pin[i]);
dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n");
}
}
}
device_init_wakeup(&pdev->dev, 1);
return usb_hcd_at91_probe(&ohci_at91_hc_driver, pdev);
}
static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
{
struct at91_usbh_data *pdata = pdev->dev.platform_data;
int i;
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
ohci_at91_usb_set_power(pdata, i, 0);
gpio_free(pdata->vbus_pin[i]);
}
for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
if (!gpio_is_valid(pdata->overcurrent_pin[i]))
continue;
free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev);
gpio_free(pdata->overcurrent_pin[i]);
}
}
device_init_wakeup(&pdev->dev, 0);
usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev);
return 0;
}
#ifdef CONFIG_PM
static int
ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
if (device_may_wakeup(&pdev->dev))
enable_irq_wake(hcd->irq);
/*
* The integrated transceivers seem unable to notice disconnect,
* reconnect, or wakeup without the 48 MHz clock active. so for
* correctness, always discard connection state (using reset).
*
* REVISIT: some boards will be able to turn VBUS off...
*/
if (at91_suspend_entering_slow_clock()) {
ohci_usb_reset (ohci);
/* flush the writes */
(void) ohci_readl (ohci, &ohci->regs->control);
at91_stop_clock();
}
return 0;
}
static int ohci_hcd_at91_drv_resume(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
if (device_may_wakeup(&pdev->dev))
disable_irq_wake(hcd->irq);
if (!clocked)
at91_start_clock();
ohci_finish_controller_resume(hcd);
return 0;
}
#else
#define ohci_hcd_at91_drv_suspend NULL
#define ohci_hcd_at91_drv_resume NULL
#endif
MODULE_ALIAS("platform:at91_ohci");
static struct platform_driver ohci_hcd_at91_driver = {
.probe = ohci_hcd_at91_drv_probe,
.remove = ohci_hcd_at91_drv_remove,
.shutdown = usb_hcd_platform_shutdown,
.suspend = ohci_hcd_at91_drv_suspend,
.resume = ohci_hcd_at91_drv_resume,
.driver = {
.name = "at91_ohci",
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(at91_ohci_dt_ids),
},
};