| # |
| # USB device configuration |
| # |
| |
| menuconfig USB_SUPPORT |
| bool "USB support" |
| depends on HAS_IOMEM |
| default y |
| ---help--- |
| This option adds core support for Universal Serial Bus (USB). |
| You will also need drivers from the following menu to make use of it. |
| |
| if USB_SUPPORT |
| |
| config USB_COMMON |
| tristate |
| default y |
| depends on USB || USB_GADGET |
| |
| # Host-side USB depends on having a host controller |
| # NOTE: dummy_hcd is always an option, but it's ignored here ... |
| # NOTE: SL-811 option should be board-specific ... |
| config USB_ARCH_HAS_HCD |
| boolean |
| default y if USB_ARCH_HAS_OHCI |
| default y if USB_ARCH_HAS_EHCI |
| default y if USB_ARCH_HAS_XHCI |
| default y if PCMCIA && !M32R # sl811_cs |
| default y if ARM # SL-811 |
| default y if BLACKFIN # SL-811 |
| default y if SUPERH # r8a66597-hcd |
| default PCI |
| |
| # many non-PCI SOC chips embed OHCI |
| config USB_ARCH_HAS_OHCI |
| boolean |
| # ARM: |
| default y if SA1111 |
| default y if ARCH_OMAP |
| default y if ARCH_S3C2410 |
| default y if PXA27x |
| default y if PXA3xx |
| default y if ARCH_EP93XX |
| default y if ARCH_AT91 |
| default y if ARCH_PNX4008 && I2C |
| default y if MFD_TC6393XB |
| default y if ARCH_W90X900 |
| default y if ARCH_DAVINCI_DA8XX |
| default y if ARCH_CNS3XXX |
| default y if PLAT_SPEAR |
| # PPC: |
| default y if STB03xxx |
| default y if PPC_MPC52xx |
| # MIPS: |
| default y if MIPS_ALCHEMY |
| default y if MACH_JZ4740 |
| # more: |
| default PCI |
| |
| # some non-PCI hcds implement EHCI |
| config USB_ARCH_HAS_EHCI |
| boolean |
| default y if FSL_SOC |
| default y if PPC_MPC512x |
| default y if ARCH_IXP4XX |
| default y if ARCH_W90X900 |
| default y if ARCH_AT91SAM9G45 |
| default y if ARCH_MXC |
| default y if ARCH_OMAP3 |
| default y if ARCH_CNS3XXX |
| default y if ARCH_VT8500 |
| default y if PLAT_SPEAR |
| default y if PLAT_S5P |
| default y if ARCH_MSM |
| default y if MICROBLAZE |
| default y if SPARC_LEON |
| default y if ARCH_MMP |
| default PCI |
| |
| # some non-PCI HCDs implement xHCI |
| config USB_ARCH_HAS_XHCI |
| boolean |
| default PCI |
| |
| # ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface. |
| config USB |
| tristate "Support for Host-side USB" |
| depends on USB_ARCH_HAS_HCD |
| select NLS # for UTF-8 strings |
| ---help--- |
| Universal Serial Bus (USB) is a specification for a serial bus |
| subsystem which offers higher speeds and more features than the |
| traditional PC serial port. The bus supplies power to peripherals |
| and allows for hot swapping. Up to 127 USB peripherals can be |
| connected to a single USB host in a tree structure. |
| |
| The USB host is the root of the tree, the peripherals are the |
| leaves and the inner nodes are special USB devices called hubs. |
| Most PCs now have USB host ports, used to connect peripherals |
| such as scanners, keyboards, mice, modems, cameras, disks, |
| flash memory, network links, and printers to the PC. |
| |
| Say Y here if your computer has a host-side USB port and you want |
| to use USB devices. You then need to say Y to at least one of the |
| Host Controller Driver (HCD) options below. Choose a USB 1.1 |
| controller, such as "UHCI HCD support" or "OHCI HCD support", |
| and "EHCI HCD (USB 2.0) support" except for older systems that |
| do not have USB 2.0 support. It doesn't normally hurt to select |
| them all if you are not certain. |
| |
| If your system has a device-side USB port, used in the peripheral |
| side of the USB protocol, see the "USB Gadget" framework instead. |
| |
| After choosing your HCD, then select drivers for the USB peripherals |
| you'll be using. You may want to check out the information provided |
| in <file:Documentation/usb/> and especially the links given in |
| <file:Documentation/usb/usb-help.txt>. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called usbcore. |
| |
| source "drivers/usb/core/Kconfig" |
| |
| source "drivers/usb/dwc3/Kconfig" |
| |
| source "drivers/usb/mon/Kconfig" |
| |
| source "drivers/usb/wusbcore/Kconfig" |
| |
| source "drivers/usb/host/Kconfig" |
| |
| source "drivers/usb/musb/Kconfig" |
| |
| source "drivers/usb/renesas_usbhs/Kconfig" |
| |
| source "drivers/usb/class/Kconfig" |
| |
| source "drivers/usb/storage/Kconfig" |
| |
| source "drivers/usb/image/Kconfig" |
| |
| comment "USB port drivers" |
| depends on USB |
| |
| config USB_USS720 |
| tristate "USS720 parport driver" |
| depends on USB && PARPORT |
| select PARPORT_NOT_PC |
| ---help--- |
| This driver is for USB parallel port adapters that use the Lucent |
| Technologies USS-720 chip. These cables are plugged into your USB |
| port and provide USB compatibility to peripherals designed with |
| parallel port interfaces. |
| |
| The chip has two modes: automatic mode and manual mode. In automatic |
| mode, it looks to the computer like a standard USB printer. Only |
| printers may be connected to the USS-720 in this mode. The generic |
| USB printer driver ("USB Printer support", above) may be used in |
| that mode, and you can say N here if you want to use the chip only |
| in this mode. |
| |
| Manual mode is not limited to printers, any parallel port |
| device should work. This driver utilizes manual mode. |
| Note however that some operations are three orders of magnitude |
| slower than on a PCI/ISA Parallel Port, so timing critical |
| applications might not work. |
| |
| Say Y here if you own an USS-720 USB->Parport cable and intend to |
| connect anything other than a printer to it. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called uss720. |
| |
| source "drivers/usb/serial/Kconfig" |
| |
| source "drivers/usb/misc/Kconfig" |
| |
| source "drivers/usb/atm/Kconfig" |
| |
| source "drivers/usb/gadget/Kconfig" |
| |
| source "drivers/usb/otg/Kconfig" |
| |
| endif # USB_SUPPORT |