blob: a54524cf42cc42689726547818fc55a33e3a1a94 [file] [log] [blame]
/*
* SPI master driver using generic bitbanged GPIO
*
* Copyright (C) 2006,2008 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/spi/spi_gpio.h>
/*
* This bitbanging SPI master driver should help make systems usable
* when a native hardware SPI engine is not available, perhaps because
* its driver isn't yet working or because the I/O pins it requires
* are used for other purposes.
*
* platform_device->driver_data ... points to spi_gpio
*
* spi->controller_state ... reserved for bitbang framework code
* spi->controller_data ... holds chipselect GPIO
*
* spi->master->dev.driver_data ... points to spi_gpio->bitbang
*/
struct spi_gpio {
struct spi_bitbang bitbang;
struct spi_gpio_platform_data pdata;
struct platform_device *pdev;
int cs_gpios[0];
};
/*----------------------------------------------------------------------*/
/*
* Because the overhead of going through four GPIO procedure calls
* per transferred bit can make performance a problem, this code
* is set up so that you can use it in either of two ways:
*
* - The slow generic way: set up platform_data to hold the GPIO
* numbers used for MISO/MOSI/SCK, and issue procedure calls for
* each of them. This driver can handle several such busses.
*
* - The quicker inlined way: only helps with platform GPIO code
* that inlines operations for constant GPIOs. This can give
* you tight (fast!) inner loops, but each such bus needs a
* new driver. You'll define a new C file, with Makefile and
* Kconfig support; the C code can be a total of six lines:
*
* #define DRIVER_NAME "myboard_spi2"
* #define SPI_MISO_GPIO 119
* #define SPI_MOSI_GPIO 120
* #define SPI_SCK_GPIO 121
* #define SPI_N_CHIPSEL 4
* #include "spi-gpio.c"
*/
#ifndef DRIVER_NAME
#define DRIVER_NAME "spi_gpio"
#define GENERIC_BITBANG /* vs tight inlines */
/* all functions referencing these symbols must define pdata */
#define SPI_MISO_GPIO ((pdata)->miso)
#define SPI_MOSI_GPIO ((pdata)->mosi)
#define SPI_SCK_GPIO ((pdata)->sck)
#define SPI_N_CHIPSEL ((pdata)->num_chipselect)
#endif
/*----------------------------------------------------------------------*/
static inline struct spi_gpio * __pure
spi_to_spi_gpio(const struct spi_device *spi)
{
const struct spi_bitbang *bang;
struct spi_gpio *spi_gpio;
bang = spi_master_get_devdata(spi->master);
spi_gpio = container_of(bang, struct spi_gpio, bitbang);
return spi_gpio;
}
static inline struct spi_gpio_platform_data * __pure
spi_to_pdata(const struct spi_device *spi)
{
return &spi_to_spi_gpio(spi)->pdata;
}
/* this is #defined to avoid unused-variable warnings when inlining */
#define pdata spi_to_pdata(spi)
static inline void setsck(const struct spi_device *spi, int is_on)
{
gpio_set_value(SPI_SCK_GPIO, is_on);
}
static inline void setmosi(const struct spi_device *spi, int is_on)
{
gpio_set_value(SPI_MOSI_GPIO, is_on);
}
static inline int getmiso(const struct spi_device *spi)
{
return !!gpio_get_value(SPI_MISO_GPIO);
}
#undef pdata
/*
* NOTE: this clocks "as fast as we can". It "should" be a function of the
* requested device clock. Software overhead means we usually have trouble
* reaching even one Mbit/sec (except when we can inline bitops), so for now
* we'll just assume we never need additional per-bit slowdowns.
*/
#define spidelay(nsecs) do {} while (0)
#include "spi-bitbang-txrx.h"
/*
* These functions can leverage inline expansion of GPIO calls to shrink
* costs for a txrx bit, often by factors of around ten (by instruction
* count). That is particularly visible for larger word sizes, but helps
* even with default 8-bit words.
*
* REVISIT overheads calling these functions for each word also have
* significant performance costs. Having txrx_bufs() calls that inline
* the txrx_word() logic would help performance, e.g. on larger blocks
* used with flash storage or MMC/SD. There should also be ways to make
* GCC be less stupid about reloading registers inside the I/O loops,
* even without inlined GPIO calls; __attribute__((hot)) on GCC 4.3?
*/
static u32 spi_gpio_txrx_word_mode0(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 0, 0, word, bits);
}
static u32 spi_gpio_txrx_word_mode1(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha1(spi, nsecs, 0, 0, word, bits);
}
static u32 spi_gpio_txrx_word_mode2(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 1, 0, word, bits);
}
static u32 spi_gpio_txrx_word_mode3(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha1(spi, nsecs, 1, 0, word, bits);
}
/*
* These functions do not call setmosi or getmiso if respective flag
* (SPI_MASTER_NO_RX or SPI_MASTER_NO_TX) is set, so they are safe to
* call when such pin is not present or defined in the controller.
* A separate set of callbacks is defined to get highest possible
* speed in the generic case (when both MISO and MOSI lines are
* available), as optimiser will remove the checks when argument is
* constant.
*/
static u32 spi_gpio_spec_txrx_word_mode0(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
unsigned flags = spi->master->flags;
return bitbang_txrx_be_cpha0(spi, nsecs, 0, flags, word, bits);
}
static u32 spi_gpio_spec_txrx_word_mode1(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
unsigned flags = spi->master->flags;
return bitbang_txrx_be_cpha1(spi, nsecs, 0, flags, word, bits);
}
static u32 spi_gpio_spec_txrx_word_mode2(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
unsigned flags = spi->master->flags;
return bitbang_txrx_be_cpha0(spi, nsecs, 1, flags, word, bits);
}
static u32 spi_gpio_spec_txrx_word_mode3(struct spi_device *spi,
unsigned nsecs, u32 word, u8 bits)
{
unsigned flags = spi->master->flags;
return bitbang_txrx_be_cpha1(spi, nsecs, 1, flags, word, bits);
}
/*----------------------------------------------------------------------*/
static void spi_gpio_chipselect(struct spi_device *spi, int is_active)
{
struct spi_gpio *spi_gpio = spi_to_spi_gpio(spi);
unsigned int cs = spi_gpio->cs_gpios[spi->chip_select];
/* set initial clock polarity */
if (is_active)
setsck(spi, spi->mode & SPI_CPOL);
if (cs != SPI_GPIO_NO_CHIPSELECT) {
/* SPI is normally active-low */
gpio_set_value(cs, (spi->mode & SPI_CS_HIGH) ? is_active : !is_active);
}
}
static int spi_gpio_setup(struct spi_device *spi)
{
unsigned int cs;
int status = 0;
struct spi_gpio *spi_gpio = spi_to_spi_gpio(spi);
struct device_node *np = spi->master->dev.of_node;
if (np) {
/*
* In DT environments, the CS GPIOs have already been
* initialized from the "cs-gpios" property of the node.
*/
cs = spi_gpio->cs_gpios[spi->chip_select];
} else {
/*
* ... otherwise, take it from spi->controller_data
*/
cs = (unsigned int) spi->controller_data;
}
if (!spi->controller_state) {
if (cs != SPI_GPIO_NO_CHIPSELECT) {
status = gpio_request(cs, dev_name(&spi->dev));
if (status)
return status;
status = gpio_direction_output(cs,
!(spi->mode & SPI_CS_HIGH));
}
}
if (!status) {
/* in case it was initialized from static board data */
spi_gpio->cs_gpios[spi->chip_select] = cs;
status = spi_bitbang_setup(spi);
}
if (status) {
if (!spi->controller_state && cs != SPI_GPIO_NO_CHIPSELECT)
gpio_free(cs);
}
return status;
}
static void spi_gpio_cleanup(struct spi_device *spi)
{
struct spi_gpio *spi_gpio = spi_to_spi_gpio(spi);
unsigned int cs = spi_gpio->cs_gpios[spi->chip_select];
if (cs != SPI_GPIO_NO_CHIPSELECT)
gpio_free(cs);
spi_bitbang_cleanup(spi);
}
static int spi_gpio_alloc(unsigned pin, const char *label, bool is_in)
{
int value;
value = gpio_request(pin, label);
if (value == 0) {
if (is_in)
value = gpio_direction_input(pin);
else
value = gpio_direction_output(pin, 0);
}
return value;
}
static int spi_gpio_request(struct spi_gpio_platform_data *pdata,
const char *label, u16 *res_flags)
{
int value;
/* NOTE: SPI_*_GPIO symbols may reference "pdata" */
if (SPI_MOSI_GPIO != SPI_GPIO_NO_MOSI) {
value = spi_gpio_alloc(SPI_MOSI_GPIO, label, false);
if (value)
goto done;
} else {
/* HW configuration without MOSI pin */
*res_flags |= SPI_MASTER_NO_TX;
}
if (SPI_MISO_GPIO != SPI_GPIO_NO_MISO) {
value = spi_gpio_alloc(SPI_MISO_GPIO, label, true);
if (value)
goto free_mosi;
} else {
/* HW configuration without MISO pin */
*res_flags |= SPI_MASTER_NO_RX;
}
value = spi_gpio_alloc(SPI_SCK_GPIO, label, false);
if (value)
goto free_miso;
goto done;
free_miso:
if (SPI_MISO_GPIO != SPI_GPIO_NO_MISO)
gpio_free(SPI_MISO_GPIO);
free_mosi:
if (SPI_MOSI_GPIO != SPI_GPIO_NO_MOSI)
gpio_free(SPI_MOSI_GPIO);
done:
return value;
}
#ifdef CONFIG_OF
static struct of_device_id spi_gpio_dt_ids[] = {
{ .compatible = "spi-gpio" },
{}
};
MODULE_DEVICE_TABLE(of, spi_gpio_dt_ids);
static int spi_gpio_probe_dt(struct platform_device *pdev)
{
int ret;
u32 tmp;
struct spi_gpio_platform_data *pdata;
struct device_node *np = pdev->dev.of_node;
const struct of_device_id *of_id =
of_match_device(spi_gpio_dt_ids, &pdev->dev);
if (!of_id)
return 0;
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
ret = of_get_named_gpio(np, "gpio-sck", 0);
if (ret < 0) {
dev_err(&pdev->dev, "gpio-sck property not found\n");
goto error_free;
}
pdata->sck = ret;
ret = of_get_named_gpio(np, "gpio-miso", 0);
if (ret < 0) {
dev_info(&pdev->dev, "gpio-miso property not found, switching to no-rx mode\n");
pdata->miso = SPI_GPIO_NO_MISO;
} else
pdata->miso = ret;
ret = of_get_named_gpio(np, "gpio-mosi", 0);
if (ret < 0) {
dev_info(&pdev->dev, "gpio-mosi property not found, switching to no-tx mode\n");
pdata->mosi = SPI_GPIO_NO_MOSI;
} else
pdata->mosi = ret;
ret = of_property_read_u32(np, "num-chipselects", &tmp);
if (ret < 0) {
dev_err(&pdev->dev, "num-chipselects property not found\n");
goto error_free;
}
pdata->num_chipselect = tmp;
pdev->dev.platform_data = pdata;
return 1;
error_free:
devm_kfree(&pdev->dev, pdata);
return ret;
}
#else
static inline int spi_gpio_probe_dt(struct platform_device *pdev)
{
return 0;
}
#endif
static int spi_gpio_probe(struct platform_device *pdev)
{
int status;
struct spi_master *master;
struct spi_gpio *spi_gpio;
struct spi_gpio_platform_data *pdata;
u16 master_flags = 0;
bool use_of = 0;
status = spi_gpio_probe_dt(pdev);
if (status < 0)
return status;
if (status > 0)
use_of = 1;
pdata = pdev->dev.platform_data;
#ifdef GENERIC_BITBANG
if (!pdata || !pdata->num_chipselect)
return -ENODEV;
#endif
status = spi_gpio_request(pdata, dev_name(&pdev->dev), &master_flags);
if (status < 0)
return status;
master = spi_alloc_master(&pdev->dev, sizeof(*spi_gpio) +
(sizeof(int) * SPI_N_CHIPSEL));
if (!master) {
status = -ENOMEM;
goto gpio_free;
}
spi_gpio = spi_master_get_devdata(master);
platform_set_drvdata(pdev, spi_gpio);
spi_gpio->pdev = pdev;
if (pdata)
spi_gpio->pdata = *pdata;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
master->flags = master_flags;
master->bus_num = pdev->id;
master->num_chipselect = SPI_N_CHIPSEL;
master->setup = spi_gpio_setup;
master->cleanup = spi_gpio_cleanup;
#ifdef CONFIG_OF
master->dev.of_node = pdev->dev.of_node;
if (use_of) {
int i;
struct device_node *np = pdev->dev.of_node;
/*
* In DT environments, take the CS GPIO from the "cs-gpios"
* property of the node.
*/
for (i = 0; i < SPI_N_CHIPSEL; i++)
spi_gpio->cs_gpios[i] =
of_get_named_gpio(np, "cs-gpios", i);
}
#endif
spi_gpio->bitbang.master = spi_master_get(master);
spi_gpio->bitbang.chipselect = spi_gpio_chipselect;
if ((master_flags & (SPI_MASTER_NO_TX | SPI_MASTER_NO_RX)) == 0) {
spi_gpio->bitbang.txrx_word[SPI_MODE_0] = spi_gpio_txrx_word_mode0;
spi_gpio->bitbang.txrx_word[SPI_MODE_1] = spi_gpio_txrx_word_mode1;
spi_gpio->bitbang.txrx_word[SPI_MODE_2] = spi_gpio_txrx_word_mode2;
spi_gpio->bitbang.txrx_word[SPI_MODE_3] = spi_gpio_txrx_word_mode3;
} else {
spi_gpio->bitbang.txrx_word[SPI_MODE_0] = spi_gpio_spec_txrx_word_mode0;
spi_gpio->bitbang.txrx_word[SPI_MODE_1] = spi_gpio_spec_txrx_word_mode1;
spi_gpio->bitbang.txrx_word[SPI_MODE_2] = spi_gpio_spec_txrx_word_mode2;
spi_gpio->bitbang.txrx_word[SPI_MODE_3] = spi_gpio_spec_txrx_word_mode3;
}
spi_gpio->bitbang.setup_transfer = spi_bitbang_setup_transfer;
spi_gpio->bitbang.flags = SPI_CS_HIGH;
status = spi_bitbang_start(&spi_gpio->bitbang);
if (status < 0) {
spi_master_put(spi_gpio->bitbang.master);
gpio_free:
if (SPI_MISO_GPIO != SPI_GPIO_NO_MISO)
gpio_free(SPI_MISO_GPIO);
if (SPI_MOSI_GPIO != SPI_GPIO_NO_MOSI)
gpio_free(SPI_MOSI_GPIO);
gpio_free(SPI_SCK_GPIO);
spi_master_put(master);
}
return status;
}
static int spi_gpio_remove(struct platform_device *pdev)
{
struct spi_gpio *spi_gpio;
struct spi_gpio_platform_data *pdata;
int status;
spi_gpio = platform_get_drvdata(pdev);
pdata = pdev->dev.platform_data;
/* stop() unregisters child devices too */
status = spi_bitbang_stop(&spi_gpio->bitbang);
spi_master_put(spi_gpio->bitbang.master);
if (SPI_MISO_GPIO != SPI_GPIO_NO_MISO)
gpio_free(SPI_MISO_GPIO);
if (SPI_MOSI_GPIO != SPI_GPIO_NO_MOSI)
gpio_free(SPI_MOSI_GPIO);
gpio_free(SPI_SCK_GPIO);
return status;
}
MODULE_ALIAS("platform:" DRIVER_NAME);
static struct platform_driver spi_gpio_driver = {
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(spi_gpio_dt_ids),
},
.probe = spi_gpio_probe,
.remove = spi_gpio_remove,
};
module_platform_driver(spi_gpio_driver);
MODULE_DESCRIPTION("SPI master driver using generic bitbanged GPIO ");
MODULE_AUTHOR("David Brownell");
MODULE_LICENSE("GPL");