| if ARCH_DAVINCI |
| |
| config AINTC |
| bool |
| |
| config CP_INTC |
| bool |
| |
| config ARCH_DAVINCI_DMx |
| select CPU_ARM926T |
| bool |
| |
| menu "TI DaVinci Implementations" |
| |
| comment "DaVinci Core Type" |
| |
| config ARCH_DAVINCI_DM644x |
| bool "DaVinci 644x based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DM355 |
| bool "DaVinci 355 based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DM646x |
| bool "DaVinci 646x based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DA830 |
| bool "DA830/OMAP-L137/AM17x based system" |
| select CP_INTC |
| select ARCH_DAVINCI_DA8XX |
| select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1 |
| |
| config ARCH_DAVINCI_DA850 |
| bool "DA850/OMAP-L138/AM18x based system" |
| select CP_INTC |
| select ARCH_DAVINCI_DA8XX |
| select ARCH_HAS_CPUFREQ |
| |
| config ARCH_DAVINCI_DA8XX |
| select CPU_ARM926T |
| bool |
| |
| config ARCH_DAVINCI_DM365 |
| bool "DaVinci 365 based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_TNETV107X |
| select CPU_V6 |
| select CP_INTC |
| bool "TNETV107X based system" |
| |
| comment "DaVinci Board Type" |
| |
| config MACH_DAVINCI_EVM |
| bool "TI DM644x EVM" |
| default ARCH_DAVINCI_DM644x |
| depends on ARCH_DAVINCI_DM644x |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM644x EVM |
| |
| config MACH_SFFSDR |
| bool "Lyrtech SFFSDR" |
| depends on ARCH_DAVINCI_DM644x |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Say Y here to select the Lyrtech Small Form Factor |
| Software Defined Radio (SFFSDR) board. |
| |
| config MACH_NEUROS_OSD2 |
| bool "Neuros OSD2 Open Television Set Top Box" |
| depends on ARCH_DAVINCI_DM644x |
| help |
| Configure this option to specify the whether the board used |
| for development is a Neuros OSD2 Open Set Top Box. |
| |
| config MACH_DAVINCI_DM355_EVM |
| bool "TI DM355 EVM" |
| default ARCH_DAVINCI_DM355 |
| depends on ARCH_DAVINCI_DM355 |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM355 EVM |
| |
| config MACH_DM355_LEOPARD |
| bool "DM355 Leopard board" |
| depends on ARCH_DAVINCI_DM355 |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM355 Leopard board. |
| |
| config MACH_DAVINCI_DM6467_EVM |
| bool "TI DM6467 EVM" |
| default ARCH_DAVINCI_DM646x |
| depends on ARCH_DAVINCI_DM646x |
| select MACH_DAVINCI_DM6467TEVM |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM6467 EVM |
| |
| config MACH_DAVINCI_DM6467TEVM |
| bool |
| |
| config MACH_DAVINCI_DM365_EVM |
| bool "TI DM365 EVM" |
| default ARCH_DAVINCI_DM365 |
| depends on ARCH_DAVINCI_DM365 |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Configure this option to specify whether the board used |
| for development is a DM365 EVM |
| |
| config MACH_DAVINCI_DA830_EVM |
| bool "TI DA830/OMAP-L137/AM17x Reference Platform" |
| default ARCH_DAVINCI_DA830 |
| depends on ARCH_DAVINCI_DA830 |
| select GPIO_PCF857X |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module. |
| |
| choice |
| prompt "Select DA830/OMAP-L137/AM17x UI board peripheral" |
| depends on MACH_DAVINCI_DA830_EVM |
| help |
| The presence of UI card on the DA830/OMAP-L137/AM17x EVM is |
| detected automatically based on successful probe of the I2C |
| based GPIO expander on that board. This option selected in this |
| menu has an effect only in case of a successful UI card detection. |
| |
| config DA830_UI_LCD |
| bool "LCD" |
| help |
| Say Y here to use the LCD as a framebuffer or simple character |
| display. |
| |
| config DA830_UI_NAND |
| bool "NAND flash" |
| help |
| Say Y here to use the NAND flash. Do not forget to setup |
| the switch correctly. |
| endchoice |
| |
| config MACH_DAVINCI_DA850_EVM |
| bool "TI DA850/OMAP-L138/AM18x Reference Platform" |
| default ARCH_DAVINCI_DA850 |
| depends on ARCH_DAVINCI_DA850 |
| help |
| Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module. |
| |
| choice |
| prompt "Select peripherals connected to expander on UI board" |
| depends on MACH_DAVINCI_DA850_EVM |
| help |
| The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x |
| EVM is detected automatically based on successful probe of the I2C |
| based GPIO expander on that card. This option selected in this |
| menu has an effect only in case of a successful UI card detection. |
| |
| config DA850_UI_NONE |
| bool "No peripheral is enabled" |
| help |
| Say Y if you do not want to enable any of the peripherals connected |
| to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card |
| |
| config DA850_UI_RMII |
| bool "RMII Ethernet PHY" |
| help |
| Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x |
| EVM. This PHY is found on the UI daughter card that is supplied with |
| the EVM. |
| NOTE: Please take care while choosing this option, MII PHY will |
| not be functional if RMII mode is selected. |
| |
| endchoice |
| |
| config GPIO_PCA953X |
| default MACH_DAVINCI_DA850_EVM |
| |
| config KEYBOARD_GPIO_POLLED |
| default MACH_DAVINCI_DA850_EVM |
| |
| config MACH_TNETV107X |
| bool "TI TNETV107X Reference Platform" |
| default ARCH_DAVINCI_TNETV107X |
| depends on ARCH_DAVINCI_TNETV107X |
| help |
| Say Y here to select the TI TNETV107X Evaluation Module. |
| |
| config MACH_MITYOMAPL138 |
| bool "Critical Link MityDSP-L138/MityARM-1808 SoM" |
| depends on ARCH_DAVINCI_DA850 |
| select MISC_DEVICES |
| select EEPROM_AT24 |
| select I2C |
| help |
| Say Y here to select the Critical Link MityDSP-L138/MityARM-1808 |
| System on Module. Information on this SoM may be found at |
| http://www.mitydsp.com |
| |
| config MACH_OMAPL138_HAWKBOARD |
| bool "TI AM1808 / OMAPL-138 Hawkboard platform" |
| depends on ARCH_DAVINCI_DA850 |
| help |
| Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform . |
| Information of this board may be found at |
| http://www.hawkboard.org/ |
| |
| config DAVINCI_MUX |
| bool "DAVINCI multiplexing support" |
| depends on ARCH_DAVINCI |
| default y |
| help |
| Pin multiplexing support for DAVINCI boards. If your bootloader |
| sets the multiplexing correctly, say N. Otherwise, or if unsure, |
| say Y. |
| |
| config DAVINCI_MUX_DEBUG |
| bool "Multiplexing debug output" |
| depends on DAVINCI_MUX |
| help |
| Makes the multiplexing functions print out a lot of debug info. |
| This is useful if you want to find out the correct values of the |
| multiplexing registers. |
| |
| config DAVINCI_MUX_WARNINGS |
| bool "Warn about pins the bootloader didn't set up" |
| depends on DAVINCI_MUX |
| help |
| Choose Y here to warn whenever driver initialization logic needs |
| to change the pin multiplexing setup. When there are no warnings |
| printed, it's safe to deselect DAVINCI_MUX for your product. |
| |
| config DAVINCI_RESET_CLOCKS |
| bool "Reset unused clocks during boot" |
| depends on ARCH_DAVINCI |
| help |
| Say Y if you want to reset unused clocks during boot. |
| This option saves power, but assumes all drivers are |
| using the clock framework. Broken drivers that do not |
| yet use clock framework may not work with this option. |
| If you are booting from another operating system, you |
| probably do not want this option enabled until your |
| device drivers work properly. |
| |
| endmenu |
| |
| endif |
