blob: 4adceb0bdb6d3c0dc8f762bb9c921d20516ded04 [file] [log] [blame]
/*
* Copyright 2004-2009 Analog Devices Inc.
* 2007-2008 HV Sistemas S.L.
* Javier Herrero <jherrero@hvsistemas.es>
* 2005 National ICT Australia (NICTA)
* Aidan Williams <aidan@nicta.com.au>
*
* Licensed under the GPL-2 or later.
*/
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
*/
const char bfin_board_name[] = "HV Sistemas H8606";
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
/*
* Driver needs to know address, irq and flag pin.
*/
#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x20300000,
.end = 0x20300002,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = 0x20300004,
.end = 0x20300006,
.flags = IORESOURCE_MEM,
},
[2] = {
.start = IRQ_PF10,
.end = IRQ_PF10,
.flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE | IRQF_SHARED | IRQF_TRIGGER_HIGH),
},
};
static struct platform_device dm9000_device = {
.id = 0,
.name = "dm9000",
.resource = dm9000_resources,
.num_resources = ARRAY_SIZE(dm9000_resources),
};
#endif
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource smc91x_resources[] = {
{
.name = "smc91x-regs",
.start = 0x20300300,
.end = 0x20300300 + 16,
.flags = IORESOURCE_MEM,
}, {
.start = IRQ_PROG_INTB,
.end = IRQ_PROG_INTB,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}, {
.start = IRQ_PF7,
.end = IRQ_PF7,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
.dev = {
.platform_data = &smc91x_info,
},
};
#endif
#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
.end = 0x20300000 + 0x100,
.flags = IORESOURCE_MEM,
}, {
.start = IRQ_PF10,
.end = IRQ_PF10,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
static struct platform_device net2272_bfin_device = {
.name = "net2272",
.id = -1,
.num_resources = ARRAY_SIZE(net2272_bfin_resources),
.resource = net2272_bfin_resources,
};
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* all SPI peripherals info goes here */
#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader (spi)",
.size = 0x40000,
.offset = 0,
.mask_flags = MTD_CAP_ROM
}, {
.name = "fpga (spi)",
.size = 0x30000,
.offset = 0x40000
}, {
.name = "linux kernel (spi)",
.size = 0x150000,
.offset = 0x70000
}, {
.name = "jffs2 root file system (spi)",
.size = 0x640000,
.offset = 0x1c0000,
}
};
static struct flash_platform_data bfin_spi_flash_data = {
.name = "m25p80",
.parts = bfin_spi_flash_partitions,
.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
.type = "m25p64",
};
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
/* this value is the baudrate divisor */
.max_speed_hz = 50000000, /* actual baudrate is SCLK/(2xspeed_hz) */
.bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
.mode = SPI_MODE_3,
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 4, /* actual baudrate is SCLK/(2xspeed_hz) */
.bus_num = 1, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
{
.modalias = "ad1836",
.max_speed_hz = 16,
.bus_num = 1,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
#endif
};
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
.start = SPI0_REGBASE,
.end = SPI0_REGBASE + 0xFF,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = CH_SPI,
.end = CH_SPI,
.flags = IORESOURCE_DMA,
},
[2] = {
.start = IRQ_SPI,
.end = IRQ_SPI,
.flags = IORESOURCE_IRQ,
}
};
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
.name = "bfin-spi",
.id = 0, /* Bus number */
.num_resources = ARRAY_SIZE(bfin_spi0_resource),
.resource = bfin_spi0_resource,
.dev = {
.platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
static struct resource bfin_uart_resources[] = {
{
.start = 0xFFC00400,
.end = 0xFFC004FF,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device bfin_uart_device = {
.name = "bfin-uart",
.id = 1,
.num_resources = ARRAY_SIZE(bfin_uart_resources),
.resource = bfin_uart_resources,
};
#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
.start = 0xFFC00400,
.end = 0xFFC004FF,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_UART0_RX,
.end = IRQ_UART0_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = CH_UART0_RX,
.end = CH_UART0_RX+1,
.flags = IORESOURCE_DMA,
},
};
static struct platform_device bfin_sir0_device = {
.name = "bfin_sir",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_sir0_resources),
.resource = bfin_sir0_resources,
};
#endif
#endif
#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
#include <linux/serial_8250.h>
#include <linux/serial.h>
/*
* Configuration for two 16550 UARTS in FPGA at addresses 0x20200000 and 0x202000010.
* running at half system clock, both with interrupt output or-ed to PF8. Change to
* suit different FPGA configuration, or to suit real 16550 UARTS connected to the bus
*/
static struct plat_serial8250_port serial8250_platform_data [] = {
{
.membase = (void *)0x20200000,
.mapbase = 0x20200000,
.irq = IRQ_PF8,
.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = 66666667,
}, {
.membase = (void *)0x20200010,
.mapbase = 0x20200010,
.irq = IRQ_PF8,
.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = 66666667,
}, {
}
};
static struct platform_device serial8250_device = {
.id = PLAT8250_DEV_PLATFORM,
.name = "serial8250",
.dev = {
.platform_data = serial8250_platform_data,
},
};
#endif
#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
/*
* Configuration for one OpenCores keyboard controller in FPGA at address 0x20200030,
* interrupt output wired to PF9. Change to suit different FPGA configuration
*/
static struct resource opencores_kbd_resources[] = {
[0] = {
.start = 0x20200030,
.end = 0x20300030 + 2,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PF9,
.end = IRQ_PF9,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
static struct platform_device opencores_kbd_device = {
.id = -1,
.name = "opencores-kbd",
.resource = opencores_kbd_resources,
.num_resources = ARRAY_SIZE(opencores_kbd_resources),
};
#endif
static struct platform_device *h8606_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
#endif
#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
&dm9000_device,
#endif
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
&smc91x_device,
#endif
#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
&net2272_bfin_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&bfin_spi0_device,
#endif
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
&serial8250_device,
#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
&opencores_kbd_device,
#endif
};
static int __init H8606_init(void)
{
printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n");
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(h8606_devices, ARRAY_SIZE(h8606_devices));
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
return 0;
}
arch_initcall(H8606_init);