| /* |
| * drivers/net/ibm_emac/ibm_emac_phy.c |
| * |
| * Driver for PowerPC 4xx on-chip ethernet controller, PHY support. |
| * Borrowed from sungem_phy.c, though I only kept the generic MII |
| * driver for now. |
| * |
| * This file should be shared with other drivers or eventually |
| * merged as the "low level" part of miilib |
| * |
| * (c) 2003, Benjamin Herrenscmidt (benh@kernel.crashing.org) |
| * (c) 2004-2005, Eugene Surovegin <ebs@ebshome.net> |
| * |
| */ |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/types.h> |
| #include <linux/netdevice.h> |
| #include <linux/mii.h> |
| #include <linux/ethtool.h> |
| #include <linux/delay.h> |
| |
| #include <asm/ocp.h> |
| |
| #include "ibm_emac_phy.h" |
| |
| static inline int phy_read(struct mii_phy *phy, int reg) |
| { |
| return phy->mdio_read(phy->dev, phy->address, reg); |
| } |
| |
| static inline void phy_write(struct mii_phy *phy, int reg, int val) |
| { |
| phy->mdio_write(phy->dev, phy->address, reg, val); |
| } |
| |
| int mii_reset_phy(struct mii_phy *phy) |
| { |
| int val; |
| int limit = 10000; |
| |
| val = phy_read(phy, MII_BMCR); |
| val &= ~BMCR_ISOLATE; |
| val |= BMCR_RESET; |
| phy_write(phy, MII_BMCR, val); |
| |
| udelay(300); |
| |
| while (limit--) { |
| val = phy_read(phy, MII_BMCR); |
| if (val >= 0 && (val & BMCR_RESET) == 0) |
| break; |
| udelay(10); |
| } |
| if ((val & BMCR_ISOLATE) && limit > 0) |
| phy_write(phy, MII_BMCR, val & ~BMCR_ISOLATE); |
| |
| return limit <= 0; |
| } |
| |
| static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise) |
| { |
| int ctl, adv; |
| |
| phy->autoneg = AUTONEG_ENABLE; |
| phy->speed = SPEED_10; |
| phy->duplex = DUPLEX_HALF; |
| phy->pause = phy->asym_pause = 0; |
| phy->advertising = advertise; |
| |
| /* Setup standard advertise */ |
| adv = phy_read(phy, MII_ADVERTISE); |
| if (adv < 0) |
| return adv; |
| adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP | |
| ADVERTISE_PAUSE_ASYM); |
| if (advertise & ADVERTISED_10baseT_Half) |
| adv |= ADVERTISE_10HALF; |
| if (advertise & ADVERTISED_10baseT_Full) |
| adv |= ADVERTISE_10FULL; |
| if (advertise & ADVERTISED_100baseT_Half) |
| adv |= ADVERTISE_100HALF; |
| if (advertise & ADVERTISED_100baseT_Full) |
| adv |= ADVERTISE_100FULL; |
| if (advertise & ADVERTISED_Pause) |
| adv |= ADVERTISE_PAUSE_CAP; |
| if (advertise & ADVERTISED_Asym_Pause) |
| adv |= ADVERTISE_PAUSE_ASYM; |
| phy_write(phy, MII_ADVERTISE, adv); |
| |
| if (phy->features & |
| (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) { |
| adv = phy_read(phy, MII_CTRL1000); |
| if (adv < 0) |
| return adv; |
| adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF); |
| if (advertise & ADVERTISED_1000baseT_Full) |
| adv |= ADVERTISE_1000FULL; |
| if (advertise & ADVERTISED_1000baseT_Half) |
| adv |= ADVERTISE_1000HALF; |
| phy_write(phy, MII_CTRL1000, adv); |
| } |
| |
| /* Start/Restart aneg */ |
| ctl = phy_read(phy, MII_BMCR); |
| ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); |
| phy_write(phy, MII_BMCR, ctl); |
| |
| return 0; |
| } |
| |
| static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd) |
| { |
| int ctl; |
| |
| phy->autoneg = AUTONEG_DISABLE; |
| phy->speed = speed; |
| phy->duplex = fd; |
| phy->pause = phy->asym_pause = 0; |
| |
| ctl = phy_read(phy, MII_BMCR); |
| if (ctl < 0) |
| return ctl; |
| ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_ANENABLE); |
| |
| /* First reset the PHY */ |
| phy_write(phy, MII_BMCR, ctl | BMCR_RESET); |
| |
| /* Select speed & duplex */ |
| switch (speed) { |
| case SPEED_10: |
| break; |
| case SPEED_100: |
| ctl |= BMCR_SPEED100; |
| break; |
| case SPEED_1000: |
| ctl |= BMCR_SPEED1000; |
| break; |
| default: |
| return -EINVAL; |
| } |
| if (fd == DUPLEX_FULL) |
| ctl |= BMCR_FULLDPLX; |
| phy_write(phy, MII_BMCR, ctl); |
| |
| return 0; |
| } |
| |
| static int genmii_poll_link(struct mii_phy *phy) |
| { |
| int status; |
| |
| /* Clear latched value with dummy read */ |
| phy_read(phy, MII_BMSR); |
| status = phy_read(phy, MII_BMSR); |
| if (status < 0 || (status & BMSR_LSTATUS) == 0) |
| return 0; |
| if (phy->autoneg == AUTONEG_ENABLE && !(status & BMSR_ANEGCOMPLETE)) |
| return 0; |
| return 1; |
| } |
| |
| static int genmii_read_link(struct mii_phy *phy) |
| { |
| if (phy->autoneg == AUTONEG_ENABLE) { |
| int glpa = 0; |
| int lpa = phy_read(phy, MII_LPA) & phy_read(phy, MII_ADVERTISE); |
| if (lpa < 0) |
| return lpa; |
| |
| if (phy->features & |
| (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) { |
| int adv = phy_read(phy, MII_CTRL1000); |
| glpa = phy_read(phy, MII_STAT1000); |
| |
| if (glpa < 0 || adv < 0) |
| return adv; |
| |
| glpa &= adv << 2; |
| } |
| |
| phy->speed = SPEED_10; |
| phy->duplex = DUPLEX_HALF; |
| phy->pause = phy->asym_pause = 0; |
| |
| if (glpa & (LPA_1000FULL | LPA_1000HALF)) { |
| phy->speed = SPEED_1000; |
| if (glpa & LPA_1000FULL) |
| phy->duplex = DUPLEX_FULL; |
| } else if (lpa & (LPA_100FULL | LPA_100HALF)) { |
| phy->speed = SPEED_100; |
| if (lpa & LPA_100FULL) |
| phy->duplex = DUPLEX_FULL; |
| } else if (lpa & LPA_10FULL) |
| phy->duplex = DUPLEX_FULL; |
| |
| if (phy->duplex == DUPLEX_FULL) { |
| phy->pause = lpa & LPA_PAUSE_CAP ? 1 : 0; |
| phy->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0; |
| } |
| } else { |
| int bmcr = phy_read(phy, MII_BMCR); |
| if (bmcr < 0) |
| return bmcr; |
| |
| if (bmcr & BMCR_FULLDPLX) |
| phy->duplex = DUPLEX_FULL; |
| else |
| phy->duplex = DUPLEX_HALF; |
| if (bmcr & BMCR_SPEED1000) |
| phy->speed = SPEED_1000; |
| else if (bmcr & BMCR_SPEED100) |
| phy->speed = SPEED_100; |
| else |
| phy->speed = SPEED_10; |
| |
| phy->pause = phy->asym_pause = 0; |
| } |
| return 0; |
| } |
| |
| /* Generic implementation for most 10/100/1000 PHYs */ |
| static struct mii_phy_ops generic_phy_ops = { |
| .setup_aneg = genmii_setup_aneg, |
| .setup_forced = genmii_setup_forced, |
| .poll_link = genmii_poll_link, |
| .read_link = genmii_read_link |
| }; |
| |
| static struct mii_phy_def genmii_phy_def = { |
| .phy_id = 0x00000000, |
| .phy_id_mask = 0x00000000, |
| .name = "Generic MII", |
| .ops = &generic_phy_ops |
| }; |
| |
| /* CIS8201 */ |
| #define MII_CIS8201_10BTCSR 0x16 |
| #define TENBTCSR_ECHO_DISABLE 0x2000 |
| #define MII_CIS8201_EPCR 0x17 |
| #define EPCR_MODE_MASK 0x3000 |
| #define EPCR_GMII_MODE 0x0000 |
| #define EPCR_RGMII_MODE 0x1000 |
| #define EPCR_TBI_MODE 0x2000 |
| #define EPCR_RTBI_MODE 0x3000 |
| #define MII_CIS8201_ACSR 0x1c |
| #define ACSR_PIN_PRIO_SELECT 0x0004 |
| |
| static int cis8201_init(struct mii_phy *phy) |
| { |
| int epcr; |
| |
| epcr = phy_read(phy, MII_CIS8201_EPCR); |
| if (epcr < 0) |
| return epcr; |
| |
| epcr &= ~EPCR_MODE_MASK; |
| |
| switch (phy->mode) { |
| case PHY_MODE_TBI: |
| epcr |= EPCR_TBI_MODE; |
| break; |
| case PHY_MODE_RTBI: |
| epcr |= EPCR_RTBI_MODE; |
| break; |
| case PHY_MODE_GMII: |
| epcr |= EPCR_GMII_MODE; |
| break; |
| case PHY_MODE_RGMII: |
| default: |
| epcr |= EPCR_RGMII_MODE; |
| } |
| |
| phy_write(phy, MII_CIS8201_EPCR, epcr); |
| |
| /* MII regs override strap pins */ |
| phy_write(phy, MII_CIS8201_ACSR, |
| phy_read(phy, MII_CIS8201_ACSR) | ACSR_PIN_PRIO_SELECT); |
| |
| /* Disable TX_EN -> CRS echo mode, otherwise 10/HDX doesn't work */ |
| phy_write(phy, MII_CIS8201_10BTCSR, |
| phy_read(phy, MII_CIS8201_10BTCSR) | TENBTCSR_ECHO_DISABLE); |
| |
| return 0; |
| } |
| |
| static struct mii_phy_ops cis8201_phy_ops = { |
| .init = cis8201_init, |
| .setup_aneg = genmii_setup_aneg, |
| .setup_forced = genmii_setup_forced, |
| .poll_link = genmii_poll_link, |
| .read_link = genmii_read_link |
| }; |
| |
| static struct mii_phy_def cis8201_phy_def = { |
| .phy_id = 0x000fc410, |
| .phy_id_mask = 0x000ffff0, |
| .name = "CIS8201 Gigabit Ethernet", |
| .ops = &cis8201_phy_ops |
| }; |
| |
| static struct mii_phy_def *mii_phy_table[] = { |
| &cis8201_phy_def, |
| &genmii_phy_def, |
| NULL |
| }; |
| |
| int mii_phy_probe(struct mii_phy *phy, int address) |
| { |
| struct mii_phy_def *def; |
| int i; |
| u32 id; |
| |
| phy->autoneg = AUTONEG_DISABLE; |
| phy->advertising = 0; |
| phy->address = address; |
| phy->speed = SPEED_10; |
| phy->duplex = DUPLEX_HALF; |
| phy->pause = phy->asym_pause = 0; |
| |
| /* Take PHY out of isolate mode and reset it. */ |
| if (mii_reset_phy(phy)) |
| return -ENODEV; |
| |
| /* Read ID and find matching entry */ |
| id = (phy_read(phy, MII_PHYSID1) << 16) | phy_read(phy, MII_PHYSID2); |
| for (i = 0; (def = mii_phy_table[i]) != NULL; i++) |
| if ((id & def->phy_id_mask) == def->phy_id) |
| break; |
| /* Should never be NULL (we have a generic entry), but... */ |
| if (!def) |
| return -ENODEV; |
| |
| phy->def = def; |
| |
| /* Determine PHY features if needed */ |
| phy->features = def->features; |
| if (!phy->features) { |
| u16 bmsr = phy_read(phy, MII_BMSR); |
| if (bmsr & BMSR_ANEGCAPABLE) |
| phy->features |= SUPPORTED_Autoneg; |
| if (bmsr & BMSR_10HALF) |
| phy->features |= SUPPORTED_10baseT_Half; |
| if (bmsr & BMSR_10FULL) |
| phy->features |= SUPPORTED_10baseT_Full; |
| if (bmsr & BMSR_100HALF) |
| phy->features |= SUPPORTED_100baseT_Half; |
| if (bmsr & BMSR_100FULL) |
| phy->features |= SUPPORTED_100baseT_Full; |
| if (bmsr & BMSR_ESTATEN) { |
| u16 esr = phy_read(phy, MII_ESTATUS); |
| if (esr & ESTATUS_1000_TFULL) |
| phy->features |= SUPPORTED_1000baseT_Full; |
| if (esr & ESTATUS_1000_THALF) |
| phy->features |= SUPPORTED_1000baseT_Half; |
| } |
| phy->features |= SUPPORTED_MII; |
| } |
| |
| /* Setup default advertising */ |
| phy->advertising = phy->features; |
| |
| return 0; |
| } |
| |
| MODULE_LICENSE("GPL"); |