| /* |
| * drivers/net/ethernet/freescale/gianfar_ethtool.c |
| * |
| * Gianfar Ethernet Driver |
| * Ethtool support for Gianfar Enet |
| * Based on e1000 ethtool support |
| * |
| * Author: Andy Fleming |
| * Maintainer: Kumar Gala |
| * Modifier: Sandeep Gopalpet <sandeep.kumar@freescale.com> |
| * |
| * Copyright 2003-2006, 2008-2009, 2011 Freescale Semiconductor, Inc. |
| * |
| * This software may be used and distributed according to |
| * the terms of the GNU Public License, Version 2, incorporated herein |
| * by reference. |
| */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/kernel.h> |
| #include <linux/string.h> |
| #include <linux/errno.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/net_tstamp.h> |
| #include <linux/skbuff.h> |
| #include <linux/spinlock.h> |
| #include <linux/mm.h> |
| |
| #include <asm/io.h> |
| #include <asm/irq.h> |
| #include <asm/uaccess.h> |
| #include <linux/module.h> |
| #include <linux/crc32.h> |
| #include <asm/types.h> |
| #include <linux/ethtool.h> |
| #include <linux/mii.h> |
| #include <linux/phy.h> |
| #include <linux/sort.h> |
| #include <linux/if_vlan.h> |
| |
| #include "gianfar.h" |
| |
| #define GFAR_MAX_COAL_USECS 0xffff |
| #define GFAR_MAX_COAL_FRAMES 0xff |
| static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy, |
| u64 *buf); |
| static void gfar_gstrings(struct net_device *dev, u32 stringset, u8 * buf); |
| static int gfar_gcoalesce(struct net_device *dev, |
| struct ethtool_coalesce *cvals); |
| static int gfar_scoalesce(struct net_device *dev, |
| struct ethtool_coalesce *cvals); |
| static void gfar_gringparam(struct net_device *dev, |
| struct ethtool_ringparam *rvals); |
| static int gfar_sringparam(struct net_device *dev, |
| struct ethtool_ringparam *rvals); |
| static void gfar_gdrvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *drvinfo); |
| |
| static const char stat_gstrings[][ETH_GSTRING_LEN] = { |
| "rx-large-frame-errors", |
| "rx-short-frame-errors", |
| "rx-non-octet-errors", |
| "rx-crc-errors", |
| "rx-overrun-errors", |
| "rx-busy-errors", |
| "rx-babbling-errors", |
| "rx-truncated-frames", |
| "ethernet-bus-error", |
| "tx-babbling-errors", |
| "tx-underrun-errors", |
| "rx-skb-missing-errors", |
| "tx-timeout-errors", |
| "tx-rx-64-frames", |
| "tx-rx-65-127-frames", |
| "tx-rx-128-255-frames", |
| "tx-rx-256-511-frames", |
| "tx-rx-512-1023-frames", |
| "tx-rx-1024-1518-frames", |
| "tx-rx-1519-1522-good-vlan", |
| "rx-bytes", |
| "rx-packets", |
| "rx-fcs-errors", |
| "receive-multicast-packet", |
| "receive-broadcast-packet", |
| "rx-control-frame-packets", |
| "rx-pause-frame-packets", |
| "rx-unknown-op-code", |
| "rx-alignment-error", |
| "rx-frame-length-error", |
| "rx-code-error", |
| "rx-carrier-sense-error", |
| "rx-undersize-packets", |
| "rx-oversize-packets", |
| "rx-fragmented-frames", |
| "rx-jabber-frames", |
| "rx-dropped-frames", |
| "tx-byte-counter", |
| "tx-packets", |
| "tx-multicast-packets", |
| "tx-broadcast-packets", |
| "tx-pause-control-frames", |
| "tx-deferral-packets", |
| "tx-excessive-deferral-packets", |
| "tx-single-collision-packets", |
| "tx-multiple-collision-packets", |
| "tx-late-collision-packets", |
| "tx-excessive-collision-packets", |
| "tx-total-collision", |
| "reserved", |
| "tx-dropped-frames", |
| "tx-jabber-frames", |
| "tx-fcs-errors", |
| "tx-control-frames", |
| "tx-oversize-frames", |
| "tx-undersize-frames", |
| "tx-fragmented-frames", |
| }; |
| |
| /* Fill in a buffer with the strings which correspond to the |
| * stats */ |
| static void gfar_gstrings(struct net_device *dev, u32 stringset, u8 * buf) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) |
| memcpy(buf, stat_gstrings, GFAR_STATS_LEN * ETH_GSTRING_LEN); |
| else |
| memcpy(buf, stat_gstrings, |
| GFAR_EXTRA_STATS_LEN * ETH_GSTRING_LEN); |
| } |
| |
| /* Fill in an array of 64-bit statistics from various sources. |
| * This array will be appended to the end of the ethtool_stats |
| * structure, and returned to user space |
| */ |
| static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy, |
| u64 *buf) |
| { |
| int i; |
| struct gfar_private *priv = netdev_priv(dev); |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; |
| atomic64_t *extra = (atomic64_t *)&priv->extra_stats; |
| |
| for (i = 0; i < GFAR_EXTRA_STATS_LEN; i++) |
| buf[i] = atomic64_read(&extra[i]); |
| |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { |
| u32 __iomem *rmon = (u32 __iomem *) ®s->rmon; |
| |
| for (; i < GFAR_STATS_LEN; i++, rmon++) |
| buf[i] = (u64) gfar_read(rmon); |
| } |
| } |
| |
| static int gfar_sset_count(struct net_device *dev, int sset) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| switch (sset) { |
| case ETH_SS_STATS: |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) |
| return GFAR_STATS_LEN; |
| else |
| return GFAR_EXTRA_STATS_LEN; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| /* Fills in the drvinfo structure with some basic info */ |
| static void gfar_gdrvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *drvinfo) |
| { |
| strlcpy(drvinfo->driver, DRV_NAME, sizeof(drvinfo->driver)); |
| strlcpy(drvinfo->version, gfar_driver_version, |
| sizeof(drvinfo->version)); |
| strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); |
| strlcpy(drvinfo->bus_info, "N/A", sizeof(drvinfo->bus_info)); |
| drvinfo->regdump_len = 0; |
| drvinfo->eedump_len = 0; |
| } |
| |
| |
| static int gfar_ssettings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| struct phy_device *phydev = priv->phydev; |
| |
| if (NULL == phydev) |
| return -ENODEV; |
| |
| return phy_ethtool_sset(phydev, cmd); |
| } |
| |
| |
| /* Return the current settings in the ethtool_cmd structure */ |
| static int gfar_gsettings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| struct phy_device *phydev = priv->phydev; |
| struct gfar_priv_rx_q *rx_queue = NULL; |
| struct gfar_priv_tx_q *tx_queue = NULL; |
| |
| if (NULL == phydev) |
| return -ENODEV; |
| tx_queue = priv->tx_queue[0]; |
| rx_queue = priv->rx_queue[0]; |
| |
| /* etsec-1.7 and older versions have only one txic |
| * and rxic regs although they support multiple queues */ |
| cmd->maxtxpkt = get_icft_value(tx_queue->txic); |
| cmd->maxrxpkt = get_icft_value(rx_queue->rxic); |
| |
| return phy_ethtool_gset(phydev, cmd); |
| } |
| |
| /* Return the length of the register structure */ |
| static int gfar_reglen(struct net_device *dev) |
| { |
| return sizeof (struct gfar); |
| } |
| |
| /* Return a dump of the GFAR register space */ |
| static void gfar_get_regs(struct net_device *dev, struct ethtool_regs *regs, |
| void *regbuf) |
| { |
| int i; |
| struct gfar_private *priv = netdev_priv(dev); |
| u32 __iomem *theregs = (u32 __iomem *) priv->gfargrp[0].regs; |
| u32 *buf = (u32 *) regbuf; |
| |
| for (i = 0; i < sizeof (struct gfar) / sizeof (u32); i++) |
| buf[i] = gfar_read(&theregs[i]); |
| } |
| |
| /* Convert microseconds to ethernet clock ticks, which changes |
| * depending on what speed the controller is running at */ |
| static unsigned int gfar_usecs2ticks(struct gfar_private *priv, |
| unsigned int usecs) |
| { |
| unsigned int count; |
| |
| /* The timer is different, depending on the interface speed */ |
| switch (priv->phydev->speed) { |
| case SPEED_1000: |
| count = GFAR_GBIT_TIME; |
| break; |
| case SPEED_100: |
| count = GFAR_100_TIME; |
| break; |
| case SPEED_10: |
| default: |
| count = GFAR_10_TIME; |
| break; |
| } |
| |
| /* Make sure we return a number greater than 0 |
| * if usecs > 0 */ |
| return (usecs * 1000 + count - 1) / count; |
| } |
| |
| /* Convert ethernet clock ticks to microseconds */ |
| static unsigned int gfar_ticks2usecs(struct gfar_private *priv, |
| unsigned int ticks) |
| { |
| unsigned int count; |
| |
| /* The timer is different, depending on the interface speed */ |
| switch (priv->phydev->speed) { |
| case SPEED_1000: |
| count = GFAR_GBIT_TIME; |
| break; |
| case SPEED_100: |
| count = GFAR_100_TIME; |
| break; |
| case SPEED_10: |
| default: |
| count = GFAR_10_TIME; |
| break; |
| } |
| |
| /* Make sure we return a number greater than 0 */ |
| /* if ticks is > 0 */ |
| return (ticks * count) / 1000; |
| } |
| |
| /* Get the coalescing parameters, and put them in the cvals |
| * structure. */ |
| static int gfar_gcoalesce(struct net_device *dev, |
| struct ethtool_coalesce *cvals) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| struct gfar_priv_rx_q *rx_queue = NULL; |
| struct gfar_priv_tx_q *tx_queue = NULL; |
| unsigned long rxtime; |
| unsigned long rxcount; |
| unsigned long txtime; |
| unsigned long txcount; |
| |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE)) |
| return -EOPNOTSUPP; |
| |
| if (NULL == priv->phydev) |
| return -ENODEV; |
| |
| rx_queue = priv->rx_queue[0]; |
| tx_queue = priv->tx_queue[0]; |
| |
| rxtime = get_ictt_value(rx_queue->rxic); |
| rxcount = get_icft_value(rx_queue->rxic); |
| txtime = get_ictt_value(tx_queue->txic); |
| txcount = get_icft_value(tx_queue->txic); |
| cvals->rx_coalesce_usecs = gfar_ticks2usecs(priv, rxtime); |
| cvals->rx_max_coalesced_frames = rxcount; |
| |
| cvals->tx_coalesce_usecs = gfar_ticks2usecs(priv, txtime); |
| cvals->tx_max_coalesced_frames = txcount; |
| |
| cvals->use_adaptive_rx_coalesce = 0; |
| cvals->use_adaptive_tx_coalesce = 0; |
| |
| cvals->pkt_rate_low = 0; |
| cvals->rx_coalesce_usecs_low = 0; |
| cvals->rx_max_coalesced_frames_low = 0; |
| cvals->tx_coalesce_usecs_low = 0; |
| cvals->tx_max_coalesced_frames_low = 0; |
| |
| /* When the packet rate is below pkt_rate_high but above |
| * pkt_rate_low (both measured in packets per second) the |
| * normal {rx,tx}_* coalescing parameters are used. |
| */ |
| |
| /* When the packet rate is (measured in packets per second) |
| * is above pkt_rate_high, the {rx,tx}_*_high parameters are |
| * used. |
| */ |
| cvals->pkt_rate_high = 0; |
| cvals->rx_coalesce_usecs_high = 0; |
| cvals->rx_max_coalesced_frames_high = 0; |
| cvals->tx_coalesce_usecs_high = 0; |
| cvals->tx_max_coalesced_frames_high = 0; |
| |
| /* How often to do adaptive coalescing packet rate sampling, |
| * measured in seconds. Must not be zero. |
| */ |
| cvals->rate_sample_interval = 0; |
| |
| return 0; |
| } |
| |
| /* Change the coalescing values. |
| * Both cvals->*_usecs and cvals->*_frames have to be > 0 |
| * in order for coalescing to be active |
| */ |
| static int gfar_scoalesce(struct net_device *dev, |
| struct ethtool_coalesce *cvals) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| int i, err = 0; |
| |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE)) |
| return -EOPNOTSUPP; |
| |
| if (NULL == priv->phydev) |
| return -ENODEV; |
| |
| /* Check the bounds of the values */ |
| if (cvals->rx_coalesce_usecs > GFAR_MAX_COAL_USECS) { |
| netdev_info(dev, "Coalescing is limited to %d microseconds\n", |
| GFAR_MAX_COAL_USECS); |
| return -EINVAL; |
| } |
| |
| if (cvals->rx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) { |
| netdev_info(dev, "Coalescing is limited to %d frames\n", |
| GFAR_MAX_COAL_FRAMES); |
| return -EINVAL; |
| } |
| |
| /* Check the bounds of the values */ |
| if (cvals->tx_coalesce_usecs > GFAR_MAX_COAL_USECS) { |
| netdev_info(dev, "Coalescing is limited to %d microseconds\n", |
| GFAR_MAX_COAL_USECS); |
| return -EINVAL; |
| } |
| |
| if (cvals->tx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) { |
| netdev_info(dev, "Coalescing is limited to %d frames\n", |
| GFAR_MAX_COAL_FRAMES); |
| return -EINVAL; |
| } |
| |
| while (test_and_set_bit_lock(GFAR_RESETTING, &priv->state)) |
| cpu_relax(); |
| |
| /* Set up rx coalescing */ |
| if ((cvals->rx_coalesce_usecs == 0) || |
| (cvals->rx_max_coalesced_frames == 0)) { |
| for (i = 0; i < priv->num_rx_queues; i++) |
| priv->rx_queue[i]->rxcoalescing = 0; |
| } else { |
| for (i = 0; i < priv->num_rx_queues; i++) |
| priv->rx_queue[i]->rxcoalescing = 1; |
| } |
| |
| for (i = 0; i < priv->num_rx_queues; i++) { |
| priv->rx_queue[i]->rxic = mk_ic_value( |
| cvals->rx_max_coalesced_frames, |
| gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs)); |
| } |
| |
| /* Set up tx coalescing */ |
| if ((cvals->tx_coalesce_usecs == 0) || |
| (cvals->tx_max_coalesced_frames == 0)) { |
| for (i = 0; i < priv->num_tx_queues; i++) |
| priv->tx_queue[i]->txcoalescing = 0; |
| } else { |
| for (i = 0; i < priv->num_tx_queues; i++) |
| priv->tx_queue[i]->txcoalescing = 1; |
| } |
| |
| for (i = 0; i < priv->num_tx_queues; i++) { |
| priv->tx_queue[i]->txic = mk_ic_value( |
| cvals->tx_max_coalesced_frames, |
| gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs)); |
| } |
| |
| if (dev->flags & IFF_UP) { |
| stop_gfar(dev); |
| err = startup_gfar(dev); |
| } else { |
| gfar_mac_reset(priv); |
| } |
| |
| clear_bit_unlock(GFAR_RESETTING, &priv->state); |
| |
| return err; |
| } |
| |
| /* Fills in rvals with the current ring parameters. Currently, |
| * rx, rx_mini, and rx_jumbo rings are the same size, as mini and |
| * jumbo are ignored by the driver */ |
| static void gfar_gringparam(struct net_device *dev, |
| struct ethtool_ringparam *rvals) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| struct gfar_priv_tx_q *tx_queue = NULL; |
| struct gfar_priv_rx_q *rx_queue = NULL; |
| |
| tx_queue = priv->tx_queue[0]; |
| rx_queue = priv->rx_queue[0]; |
| |
| rvals->rx_max_pending = GFAR_RX_MAX_RING_SIZE; |
| rvals->rx_mini_max_pending = GFAR_RX_MAX_RING_SIZE; |
| rvals->rx_jumbo_max_pending = GFAR_RX_MAX_RING_SIZE; |
| rvals->tx_max_pending = GFAR_TX_MAX_RING_SIZE; |
| |
| /* Values changeable by the user. The valid values are |
| * in the range 1 to the "*_max_pending" counterpart above. |
| */ |
| rvals->rx_pending = rx_queue->rx_ring_size; |
| rvals->rx_mini_pending = rx_queue->rx_ring_size; |
| rvals->rx_jumbo_pending = rx_queue->rx_ring_size; |
| rvals->tx_pending = tx_queue->tx_ring_size; |
| } |
| |
| /* Change the current ring parameters, stopping the controller if |
| * necessary so that we don't mess things up while we're in motion. |
| */ |
| static int gfar_sringparam(struct net_device *dev, |
| struct ethtool_ringparam *rvals) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| int err = 0, i; |
| |
| if (rvals->rx_pending > GFAR_RX_MAX_RING_SIZE) |
| return -EINVAL; |
| |
| if (!is_power_of_2(rvals->rx_pending)) { |
| netdev_err(dev, "Ring sizes must be a power of 2\n"); |
| return -EINVAL; |
| } |
| |
| if (rvals->tx_pending > GFAR_TX_MAX_RING_SIZE) |
| return -EINVAL; |
| |
| if (!is_power_of_2(rvals->tx_pending)) { |
| netdev_err(dev, "Ring sizes must be a power of 2\n"); |
| return -EINVAL; |
| } |
| |
| while (test_and_set_bit_lock(GFAR_RESETTING, &priv->state)) |
| cpu_relax(); |
| |
| if (dev->flags & IFF_UP) |
| stop_gfar(dev); |
| |
| /* Change the sizes */ |
| for (i = 0; i < priv->num_rx_queues; i++) |
| priv->rx_queue[i]->rx_ring_size = rvals->rx_pending; |
| |
| for (i = 0; i < priv->num_tx_queues; i++) |
| priv->tx_queue[i]->tx_ring_size = rvals->tx_pending; |
| |
| /* Rebuild the rings with the new size */ |
| if (dev->flags & IFF_UP) |
| err = startup_gfar(dev); |
| |
| clear_bit_unlock(GFAR_RESETTING, &priv->state); |
| |
| return err; |
| } |
| |
| static void gfar_gpauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *epause) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| epause->autoneg = !!priv->pause_aneg_en; |
| epause->rx_pause = !!priv->rx_pause_en; |
| epause->tx_pause = !!priv->tx_pause_en; |
| } |
| |
| static int gfar_spauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *epause) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| struct phy_device *phydev = priv->phydev; |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; |
| u32 oldadv, newadv; |
| |
| if (!(phydev->supported & SUPPORTED_Pause) || |
| (!(phydev->supported & SUPPORTED_Asym_Pause) && |
| (epause->rx_pause != epause->tx_pause))) |
| return -EINVAL; |
| |
| priv->rx_pause_en = priv->tx_pause_en = 0; |
| if (epause->rx_pause) { |
| priv->rx_pause_en = 1; |
| |
| if (epause->tx_pause) { |
| priv->tx_pause_en = 1; |
| /* FLOW_CTRL_RX & TX */ |
| newadv = ADVERTISED_Pause; |
| } else /* FLOW_CTLR_RX */ |
| newadv = ADVERTISED_Pause | ADVERTISED_Asym_Pause; |
| } else if (epause->tx_pause) { |
| priv->tx_pause_en = 1; |
| /* FLOW_CTLR_TX */ |
| newadv = ADVERTISED_Asym_Pause; |
| } else |
| newadv = 0; |
| |
| if (epause->autoneg) |
| priv->pause_aneg_en = 1; |
| else |
| priv->pause_aneg_en = 0; |
| |
| oldadv = phydev->advertising & |
| (ADVERTISED_Pause | ADVERTISED_Asym_Pause); |
| if (oldadv != newadv) { |
| phydev->advertising &= |
| ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause); |
| phydev->advertising |= newadv; |
| if (phydev->autoneg) |
| /* inform link partner of our |
| * new flow ctrl settings |
| */ |
| return phy_start_aneg(phydev); |
| |
| if (!epause->autoneg) { |
| u32 tempval; |
| tempval = gfar_read(®s->maccfg1); |
| tempval &= ~(MACCFG1_TX_FLOW | MACCFG1_RX_FLOW); |
| if (priv->tx_pause_en) |
| tempval |= MACCFG1_TX_FLOW; |
| if (priv->rx_pause_en) |
| tempval |= MACCFG1_RX_FLOW; |
| gfar_write(®s->maccfg1, tempval); |
| } |
| } |
| |
| return 0; |
| } |
| |
| int gfar_set_features(struct net_device *dev, netdev_features_t features) |
| { |
| netdev_features_t changed = dev->features ^ features; |
| struct gfar_private *priv = netdev_priv(dev); |
| int err = 0; |
| |
| if (!(changed & (NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX | |
| NETIF_F_RXCSUM))) |
| return 0; |
| |
| while (test_and_set_bit_lock(GFAR_RESETTING, &priv->state)) |
| cpu_relax(); |
| |
| dev->features = features; |
| |
| if (dev->flags & IFF_UP) { |
| /* Now we take down the rings to rebuild them */ |
| stop_gfar(dev); |
| err = startup_gfar(dev); |
| } else { |
| gfar_mac_reset(priv); |
| } |
| |
| clear_bit_unlock(GFAR_RESETTING, &priv->state); |
| |
| return err; |
| } |
| |
| static uint32_t gfar_get_msglevel(struct net_device *dev) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| return priv->msg_enable; |
| } |
| |
| static void gfar_set_msglevel(struct net_device *dev, uint32_t data) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| priv->msg_enable = data; |
| } |
| |
| #ifdef CONFIG_PM |
| static void gfar_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) { |
| wol->supported = WAKE_MAGIC; |
| wol->wolopts = priv->wol_en ? WAKE_MAGIC : 0; |
| } else { |
| wol->supported = wol->wolopts = 0; |
| } |
| } |
| |
| static int gfar_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| unsigned long flags; |
| |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) && |
| wol->wolopts != 0) |
| return -EINVAL; |
| |
| if (wol->wolopts & ~WAKE_MAGIC) |
| return -EINVAL; |
| |
| device_set_wakeup_enable(&dev->dev, wol->wolopts & WAKE_MAGIC); |
| |
| spin_lock_irqsave(&priv->bflock, flags); |
| priv->wol_en = !!device_may_wakeup(&dev->dev); |
| spin_unlock_irqrestore(&priv->bflock, flags); |
| |
| return 0; |
| } |
| #endif |
| |
| static void ethflow_to_filer_rules (struct gfar_private *priv, u64 ethflow) |
| { |
| u32 fcr = 0x0, fpr = FPR_FILER_MASK; |
| |
| if (ethflow & RXH_L2DA) { |
| fcr = RQFCR_PID_DAH |RQFCR_CMP_NOMATCH | |
| RQFCR_HASH | RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| |
| fcr = RQFCR_PID_DAL | RQFCR_AND | RQFCR_CMP_NOMATCH | |
| RQFCR_HASH | RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & RXH_VLAN) { |
| fcr = RQFCR_PID_VID | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & RXH_IP_SRC) { |
| fcr = RQFCR_PID_SIA | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & (RXH_IP_DST)) { |
| fcr = RQFCR_PID_DIA | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & RXH_L3_PROTO) { |
| fcr = RQFCR_PID_L4P | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & RXH_L4_B_0_1) { |
| fcr = RQFCR_PID_SPT | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| if (ethflow & RXH_L4_B_2_3) { |
| fcr = RQFCR_PID_DPT | RQFCR_CMP_NOMATCH | RQFCR_HASH | |
| RQFCR_AND | RQFCR_HASHTBL_0; |
| priv->ftp_rqfpr[priv->cur_filer_idx] = fpr; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = fcr; |
| gfar_write_filer(priv, priv->cur_filer_idx, fcr, fpr); |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| } |
| |
| static int gfar_ethflow_to_filer_table(struct gfar_private *priv, u64 ethflow, |
| u64 class) |
| { |
| unsigned int last_rule_idx = priv->cur_filer_idx; |
| unsigned int cmp_rqfpr; |
| unsigned int *local_rqfpr; |
| unsigned int *local_rqfcr; |
| int i = 0x0, k = 0x0; |
| int j = MAX_FILER_IDX, l = 0x0; |
| int ret = 1; |
| |
| local_rqfpr = kmalloc_array(MAX_FILER_IDX + 1, sizeof(unsigned int), |
| GFP_KERNEL); |
| local_rqfcr = kmalloc_array(MAX_FILER_IDX + 1, sizeof(unsigned int), |
| GFP_KERNEL); |
| if (!local_rqfpr || !local_rqfcr) { |
| ret = 0; |
| goto err; |
| } |
| |
| switch (class) { |
| case TCP_V4_FLOW: |
| cmp_rqfpr = RQFPR_IPV4 |RQFPR_TCP; |
| break; |
| case UDP_V4_FLOW: |
| cmp_rqfpr = RQFPR_IPV4 |RQFPR_UDP; |
| break; |
| case TCP_V6_FLOW: |
| cmp_rqfpr = RQFPR_IPV6 |RQFPR_TCP; |
| break; |
| case UDP_V6_FLOW: |
| cmp_rqfpr = RQFPR_IPV6 |RQFPR_UDP; |
| break; |
| default: |
| netdev_err(priv->ndev, |
| "Right now this class is not supported\n"); |
| ret = 0; |
| goto err; |
| } |
| |
| for (i = 0; i < MAX_FILER_IDX + 1; i++) { |
| local_rqfpr[j] = priv->ftp_rqfpr[i]; |
| local_rqfcr[j] = priv->ftp_rqfcr[i]; |
| j--; |
| if ((priv->ftp_rqfcr[i] == |
| (RQFCR_PID_PARSE | RQFCR_CLE | RQFCR_AND)) && |
| (priv->ftp_rqfpr[i] == cmp_rqfpr)) |
| break; |
| } |
| |
| if (i == MAX_FILER_IDX + 1) { |
| netdev_err(priv->ndev, |
| "No parse rule found, can't create hash rules\n"); |
| ret = 0; |
| goto err; |
| } |
| |
| /* If a match was found, then it begins the starting of a cluster rule |
| * if it was already programmed, we need to overwrite these rules |
| */ |
| for (l = i+1; l < MAX_FILER_IDX; l++) { |
| if ((priv->ftp_rqfcr[l] & RQFCR_CLE) && |
| !(priv->ftp_rqfcr[l] & RQFCR_AND)) { |
| priv->ftp_rqfcr[l] = RQFCR_CLE | RQFCR_CMP_EXACT | |
| RQFCR_HASHTBL_0 | RQFCR_PID_MASK; |
| priv->ftp_rqfpr[l] = FPR_FILER_MASK; |
| gfar_write_filer(priv, l, priv->ftp_rqfcr[l], |
| priv->ftp_rqfpr[l]); |
| break; |
| } |
| |
| if (!(priv->ftp_rqfcr[l] & RQFCR_CLE) && |
| (priv->ftp_rqfcr[l] & RQFCR_AND)) |
| continue; |
| else { |
| local_rqfpr[j] = priv->ftp_rqfpr[l]; |
| local_rqfcr[j] = priv->ftp_rqfcr[l]; |
| j--; |
| } |
| } |
| |
| priv->cur_filer_idx = l - 1; |
| last_rule_idx = l; |
| |
| /* hash rules */ |
| ethflow_to_filer_rules(priv, ethflow); |
| |
| /* Write back the popped out rules again */ |
| for (k = j+1; k < MAX_FILER_IDX; k++) { |
| priv->ftp_rqfpr[priv->cur_filer_idx] = local_rqfpr[k]; |
| priv->ftp_rqfcr[priv->cur_filer_idx] = local_rqfcr[k]; |
| gfar_write_filer(priv, priv->cur_filer_idx, |
| local_rqfcr[k], local_rqfpr[k]); |
| if (!priv->cur_filer_idx) |
| break; |
| priv->cur_filer_idx = priv->cur_filer_idx - 1; |
| } |
| |
| err: |
| kfree(local_rqfcr); |
| kfree(local_rqfpr); |
| return ret; |
| } |
| |
| static int gfar_set_hash_opts(struct gfar_private *priv, |
| struct ethtool_rxnfc *cmd) |
| { |
| /* write the filer rules here */ |
| if (!gfar_ethflow_to_filer_table(priv, cmd->data, cmd->flow_type)) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static int gfar_check_filer_hardware(struct gfar_private *priv) |
| { |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; |
| u32 i; |
| |
| /* Check if we are in FIFO mode */ |
| i = gfar_read(®s->ecntrl); |
| i &= ECNTRL_FIFM; |
| if (i == ECNTRL_FIFM) { |
| netdev_notice(priv->ndev, "Interface in FIFO mode\n"); |
| i = gfar_read(®s->rctrl); |
| i &= RCTRL_PRSDEP_MASK | RCTRL_PRSFM; |
| if (i == (RCTRL_PRSDEP_MASK | RCTRL_PRSFM)) { |
| netdev_info(priv->ndev, |
| "Receive Queue Filtering enabled\n"); |
| } else { |
| netdev_warn(priv->ndev, |
| "Receive Queue Filtering disabled\n"); |
| return -EOPNOTSUPP; |
| } |
| } |
| /* Or in standard mode */ |
| else { |
| i = gfar_read(®s->rctrl); |
| i &= RCTRL_PRSDEP_MASK; |
| if (i == RCTRL_PRSDEP_MASK) { |
| netdev_info(priv->ndev, |
| "Receive Queue Filtering enabled\n"); |
| } else { |
| netdev_warn(priv->ndev, |
| "Receive Queue Filtering disabled\n"); |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| /* Sets the properties for arbitrary filer rule |
| * to the first 4 Layer 4 Bytes |
| */ |
| gfar_write(®s->rbifx, 0xC0C1C2C3); |
| return 0; |
| } |
| |
| static int gfar_comp_asc(const void *a, const void *b) |
| { |
| return memcmp(a, b, 4); |
| } |
| |
| static int gfar_comp_desc(const void *a, const void *b) |
| { |
| return -memcmp(a, b, 4); |
| } |
| |
| static void gfar_swap(void *a, void *b, int size) |
| { |
| u32 *_a = a; |
| u32 *_b = b; |
| |
| swap(_a[0], _b[0]); |
| swap(_a[1], _b[1]); |
| swap(_a[2], _b[2]); |
| swap(_a[3], _b[3]); |
| } |
| |
| /* Write a mask to filer cache */ |
| static void gfar_set_mask(u32 mask, struct filer_table *tab) |
| { |
| tab->fe[tab->index].ctrl = RQFCR_AND | RQFCR_PID_MASK | RQFCR_CMP_EXACT; |
| tab->fe[tab->index].prop = mask; |
| tab->index++; |
| } |
| |
| /* Sets parse bits (e.g. IP or TCP) */ |
| static void gfar_set_parse_bits(u32 value, u32 mask, struct filer_table *tab) |
| { |
| gfar_set_mask(mask, tab); |
| tab->fe[tab->index].ctrl = RQFCR_CMP_EXACT | RQFCR_PID_PARSE | |
| RQFCR_AND; |
| tab->fe[tab->index].prop = value; |
| tab->index++; |
| } |
| |
| static void gfar_set_general_attribute(u32 value, u32 mask, u32 flag, |
| struct filer_table *tab) |
| { |
| gfar_set_mask(mask, tab); |
| tab->fe[tab->index].ctrl = RQFCR_CMP_EXACT | RQFCR_AND | flag; |
| tab->fe[tab->index].prop = value; |
| tab->index++; |
| } |
| |
| /* For setting a tuple of value and mask of type flag |
| * Example: |
| * IP-Src = 10.0.0.0/255.0.0.0 |
| * value: 0x0A000000 mask: FF000000 flag: RQFPR_IPV4 |
| * |
| * Ethtool gives us a value=0 and mask=~0 for don't care a tuple |
| * For a don't care mask it gives us a 0 |
| * |
| * The check if don't care and the mask adjustment if mask=0 is done for VLAN |
| * and MAC stuff on an upper level (due to missing information on this level). |
| * For these guys we can discard them if they are value=0 and mask=0. |
| * |
| * Further the all masks are one-padded for better hardware efficiency. |
| */ |
| static void gfar_set_attribute(u32 value, u32 mask, u32 flag, |
| struct filer_table *tab) |
| { |
| switch (flag) { |
| /* 3bit */ |
| case RQFCR_PID_PRI: |
| if (!(value | mask)) |
| return; |
| mask |= RQFCR_PID_PRI_MASK; |
| break; |
| /* 8bit */ |
| case RQFCR_PID_L4P: |
| case RQFCR_PID_TOS: |
| if (!~(mask | RQFCR_PID_L4P_MASK)) |
| return; |
| if (!mask) |
| mask = ~0; |
| else |
| mask |= RQFCR_PID_L4P_MASK; |
| break; |
| /* 12bit */ |
| case RQFCR_PID_VID: |
| if (!(value | mask)) |
| return; |
| mask |= RQFCR_PID_VID_MASK; |
| break; |
| /* 16bit */ |
| case RQFCR_PID_DPT: |
| case RQFCR_PID_SPT: |
| case RQFCR_PID_ETY: |
| if (!~(mask | RQFCR_PID_PORT_MASK)) |
| return; |
| if (!mask) |
| mask = ~0; |
| else |
| mask |= RQFCR_PID_PORT_MASK; |
| break; |
| /* 24bit */ |
| case RQFCR_PID_DAH: |
| case RQFCR_PID_DAL: |
| case RQFCR_PID_SAH: |
| case RQFCR_PID_SAL: |
| if (!(value | mask)) |
| return; |
| mask |= RQFCR_PID_MAC_MASK; |
| break; |
| /* for all real 32bit masks */ |
| default: |
| if (!~mask) |
| return; |
| if (!mask) |
| mask = ~0; |
| break; |
| } |
| gfar_set_general_attribute(value, mask, flag, tab); |
| } |
| |
| /* Translates value and mask for UDP, TCP or SCTP */ |
| static void gfar_set_basic_ip(struct ethtool_tcpip4_spec *value, |
| struct ethtool_tcpip4_spec *mask, |
| struct filer_table *tab) |
| { |
| gfar_set_attribute(be32_to_cpu(value->ip4src), |
| be32_to_cpu(mask->ip4src), |
| RQFCR_PID_SIA, tab); |
| gfar_set_attribute(be32_to_cpu(value->ip4dst), |
| be32_to_cpu(mask->ip4dst), |
| RQFCR_PID_DIA, tab); |
| gfar_set_attribute(be16_to_cpu(value->pdst), |
| be16_to_cpu(mask->pdst), |
| RQFCR_PID_DPT, tab); |
| gfar_set_attribute(be16_to_cpu(value->psrc), |
| be16_to_cpu(mask->psrc), |
| RQFCR_PID_SPT, tab); |
| gfar_set_attribute(value->tos, mask->tos, RQFCR_PID_TOS, tab); |
| } |
| |
| /* Translates value and mask for RAW-IP4 */ |
| static void gfar_set_user_ip(struct ethtool_usrip4_spec *value, |
| struct ethtool_usrip4_spec *mask, |
| struct filer_table *tab) |
| { |
| gfar_set_attribute(be32_to_cpu(value->ip4src), |
| be32_to_cpu(mask->ip4src), |
| RQFCR_PID_SIA, tab); |
| gfar_set_attribute(be32_to_cpu(value->ip4dst), |
| be32_to_cpu(mask->ip4dst), |
| RQFCR_PID_DIA, tab); |
| gfar_set_attribute(value->tos, mask->tos, RQFCR_PID_TOS, tab); |
| gfar_set_attribute(value->proto, mask->proto, RQFCR_PID_L4P, tab); |
| gfar_set_attribute(be32_to_cpu(value->l4_4_bytes), |
| be32_to_cpu(mask->l4_4_bytes), |
| RQFCR_PID_ARB, tab); |
| |
| } |
| |
| /* Translates value and mask for ETHER spec */ |
| static void gfar_set_ether(struct ethhdr *value, struct ethhdr *mask, |
| struct filer_table *tab) |
| { |
| u32 upper_temp_mask = 0; |
| u32 lower_temp_mask = 0; |
| |
| /* Source address */ |
| if (!is_broadcast_ether_addr(mask->h_source)) { |
| if (is_zero_ether_addr(mask->h_source)) { |
| upper_temp_mask = 0xFFFFFFFF; |
| lower_temp_mask = 0xFFFFFFFF; |
| } else { |
| upper_temp_mask = mask->h_source[0] << 16 | |
| mask->h_source[1] << 8 | |
| mask->h_source[2]; |
| lower_temp_mask = mask->h_source[3] << 16 | |
| mask->h_source[4] << 8 | |
| mask->h_source[5]; |
| } |
| /* Upper 24bit */ |
| gfar_set_attribute(value->h_source[0] << 16 | |
| value->h_source[1] << 8 | |
| value->h_source[2], |
| upper_temp_mask, RQFCR_PID_SAH, tab); |
| /* And the same for the lower part */ |
| gfar_set_attribute(value->h_source[3] << 16 | |
| value->h_source[4] << 8 | |
| value->h_source[5], |
| lower_temp_mask, RQFCR_PID_SAL, tab); |
| } |
| /* Destination address */ |
| if (!is_broadcast_ether_addr(mask->h_dest)) { |
| /* Special for destination is limited broadcast */ |
| if ((is_broadcast_ether_addr(value->h_dest) && |
| is_zero_ether_addr(mask->h_dest))) { |
| gfar_set_parse_bits(RQFPR_EBC, RQFPR_EBC, tab); |
| } else { |
| if (is_zero_ether_addr(mask->h_dest)) { |
| upper_temp_mask = 0xFFFFFFFF; |
| lower_temp_mask = 0xFFFFFFFF; |
| } else { |
| upper_temp_mask = mask->h_dest[0] << 16 | |
| mask->h_dest[1] << 8 | |
| mask->h_dest[2]; |
| lower_temp_mask = mask->h_dest[3] << 16 | |
| mask->h_dest[4] << 8 | |
| mask->h_dest[5]; |
| } |
| |
| /* Upper 24bit */ |
| gfar_set_attribute(value->h_dest[0] << 16 | |
| value->h_dest[1] << 8 | |
| value->h_dest[2], |
| upper_temp_mask, RQFCR_PID_DAH, tab); |
| /* And the same for the lower part */ |
| gfar_set_attribute(value->h_dest[3] << 16 | |
| value->h_dest[4] << 8 | |
| value->h_dest[5], |
| lower_temp_mask, RQFCR_PID_DAL, tab); |
| } |
| } |
| |
| gfar_set_attribute(be16_to_cpu(value->h_proto), |
| be16_to_cpu(mask->h_proto), |
| RQFCR_PID_ETY, tab); |
| } |
| |
| static inline u32 vlan_tci_vid(struct ethtool_rx_flow_spec *rule) |
| { |
| return be16_to_cpu(rule->h_ext.vlan_tci) & VLAN_VID_MASK; |
| } |
| |
| static inline u32 vlan_tci_vidm(struct ethtool_rx_flow_spec *rule) |
| { |
| return be16_to_cpu(rule->m_ext.vlan_tci) & VLAN_VID_MASK; |
| } |
| |
| static inline u32 vlan_tci_cfi(struct ethtool_rx_flow_spec *rule) |
| { |
| return be16_to_cpu(rule->h_ext.vlan_tci) & VLAN_CFI_MASK; |
| } |
| |
| static inline u32 vlan_tci_cfim(struct ethtool_rx_flow_spec *rule) |
| { |
| return be16_to_cpu(rule->m_ext.vlan_tci) & VLAN_CFI_MASK; |
| } |
| |
| static inline u32 vlan_tci_prio(struct ethtool_rx_flow_spec *rule) |
| { |
| return (be16_to_cpu(rule->h_ext.vlan_tci) & VLAN_PRIO_MASK) >> |
| VLAN_PRIO_SHIFT; |
| } |
| |
| static inline u32 vlan_tci_priom(struct ethtool_rx_flow_spec *rule) |
| { |
| return (be16_to_cpu(rule->m_ext.vlan_tci) & VLAN_PRIO_MASK) >> |
| VLAN_PRIO_SHIFT; |
| } |
| |
| /* Convert a rule to binary filter format of gianfar */ |
| static int gfar_convert_to_filer(struct ethtool_rx_flow_spec *rule, |
| struct filer_table *tab) |
| { |
| u32 vlan = 0, vlan_mask = 0; |
| u32 id = 0, id_mask = 0; |
| u32 cfi = 0, cfi_mask = 0; |
| u32 prio = 0, prio_mask = 0; |
| u32 old_index = tab->index; |
| |
| /* Check if vlan is wanted */ |
| if ((rule->flow_type & FLOW_EXT) && |
| (rule->m_ext.vlan_tci != cpu_to_be16(0xFFFF))) { |
| if (!rule->m_ext.vlan_tci) |
| rule->m_ext.vlan_tci = cpu_to_be16(0xFFFF); |
| |
| vlan = RQFPR_VLN; |
| vlan_mask = RQFPR_VLN; |
| |
| /* Separate the fields */ |
| id = vlan_tci_vid(rule); |
| id_mask = vlan_tci_vidm(rule); |
| cfi = vlan_tci_cfi(rule); |
| cfi_mask = vlan_tci_cfim(rule); |
| prio = vlan_tci_prio(rule); |
| prio_mask = vlan_tci_priom(rule); |
| |
| if (cfi == VLAN_TAG_PRESENT && cfi_mask == VLAN_TAG_PRESENT) { |
| vlan |= RQFPR_CFI; |
| vlan_mask |= RQFPR_CFI; |
| } else if (cfi != VLAN_TAG_PRESENT && |
| cfi_mask == VLAN_TAG_PRESENT) { |
| vlan_mask |= RQFPR_CFI; |
| } |
| } |
| |
| switch (rule->flow_type & ~FLOW_EXT) { |
| case TCP_V4_FLOW: |
| gfar_set_parse_bits(RQFPR_IPV4 | RQFPR_TCP | vlan, |
| RQFPR_IPV4 | RQFPR_TCP | vlan_mask, tab); |
| gfar_set_basic_ip(&rule->h_u.tcp_ip4_spec, |
| &rule->m_u.tcp_ip4_spec, tab); |
| break; |
| case UDP_V4_FLOW: |
| gfar_set_parse_bits(RQFPR_IPV4 | RQFPR_UDP | vlan, |
| RQFPR_IPV4 | RQFPR_UDP | vlan_mask, tab); |
| gfar_set_basic_ip(&rule->h_u.udp_ip4_spec, |
| &rule->m_u.udp_ip4_spec, tab); |
| break; |
| case SCTP_V4_FLOW: |
| gfar_set_parse_bits(RQFPR_IPV4 | vlan, RQFPR_IPV4 | vlan_mask, |
| tab); |
| gfar_set_attribute(132, 0, RQFCR_PID_L4P, tab); |
| gfar_set_basic_ip((struct ethtool_tcpip4_spec *)&rule->h_u, |
| (struct ethtool_tcpip4_spec *)&rule->m_u, |
| tab); |
| break; |
| case IP_USER_FLOW: |
| gfar_set_parse_bits(RQFPR_IPV4 | vlan, RQFPR_IPV4 | vlan_mask, |
| tab); |
| gfar_set_user_ip((struct ethtool_usrip4_spec *) &rule->h_u, |
| (struct ethtool_usrip4_spec *) &rule->m_u, |
| tab); |
| break; |
| case ETHER_FLOW: |
| if (vlan) |
| gfar_set_parse_bits(vlan, vlan_mask, tab); |
| gfar_set_ether((struct ethhdr *) &rule->h_u, |
| (struct ethhdr *) &rule->m_u, tab); |
| break; |
| default: |
| return -1; |
| } |
| |
| /* Set the vlan attributes in the end */ |
| if (vlan) { |
| gfar_set_attribute(id, id_mask, RQFCR_PID_VID, tab); |
| gfar_set_attribute(prio, prio_mask, RQFCR_PID_PRI, tab); |
| } |
| |
| /* If there has been nothing written till now, it must be a default */ |
| if (tab->index == old_index) { |
| gfar_set_mask(0xFFFFFFFF, tab); |
| tab->fe[tab->index].ctrl = 0x20; |
| tab->fe[tab->index].prop = 0x0; |
| tab->index++; |
| } |
| |
| /* Remove last AND */ |
| tab->fe[tab->index - 1].ctrl &= (~RQFCR_AND); |
| |
| /* Specify which queue to use or to drop */ |
| if (rule->ring_cookie == RX_CLS_FLOW_DISC) |
| tab->fe[tab->index - 1].ctrl |= RQFCR_RJE; |
| else |
| tab->fe[tab->index - 1].ctrl |= (rule->ring_cookie << 10); |
| |
| /* Only big enough entries can be clustered */ |
| if (tab->index > (old_index + 2)) { |
| tab->fe[old_index + 1].ctrl |= RQFCR_CLE; |
| tab->fe[tab->index - 1].ctrl |= RQFCR_CLE; |
| } |
| |
| /* In rare cases the cache can be full while there is |
| * free space in hw |
| */ |
| if (tab->index > MAX_FILER_CACHE_IDX - 1) |
| return -EBUSY; |
| |
| return 0; |
| } |
| |
| /* Copy size filer entries */ |
| static void gfar_copy_filer_entries(struct gfar_filer_entry dst[0], |
| struct gfar_filer_entry src[0], s32 size) |
| { |
| while (size > 0) { |
| size--; |
| dst[size].ctrl = src[size].ctrl; |
| dst[size].prop = src[size].prop; |
| } |
| } |
| |
| /* Delete the contents of the filer-table between start and end |
| * and collapse them |
| */ |
| static int gfar_trim_filer_entries(u32 begin, u32 end, struct filer_table *tab) |
| { |
| int length; |
| |
| if (end > MAX_FILER_CACHE_IDX || end < begin) |
| return -EINVAL; |
| |
| end++; |
| length = end - begin; |
| |
| /* Copy */ |
| while (end < tab->index) { |
| tab->fe[begin].ctrl = tab->fe[end].ctrl; |
| tab->fe[begin++].prop = tab->fe[end++].prop; |
| |
| } |
| /* Fill up with don't cares */ |
| while (begin < tab->index) { |
| tab->fe[begin].ctrl = 0x60; |
| tab->fe[begin].prop = 0xFFFFFFFF; |
| begin++; |
| } |
| |
| tab->index -= length; |
| return 0; |
| } |
| |
| /* Make space on the wanted location */ |
| static int gfar_expand_filer_entries(u32 begin, u32 length, |
| struct filer_table *tab) |
| { |
| if (length == 0 || length + tab->index > MAX_FILER_CACHE_IDX || |
| begin > MAX_FILER_CACHE_IDX) |
| return -EINVAL; |
| |
| gfar_copy_filer_entries(&(tab->fe[begin + length]), &(tab->fe[begin]), |
| tab->index - length + 1); |
| |
| tab->index += length; |
| return 0; |
| } |
| |
| static int gfar_get_next_cluster_start(int start, struct filer_table *tab) |
| { |
| for (; (start < tab->index) && (start < MAX_FILER_CACHE_IDX - 1); |
| start++) { |
| if ((tab->fe[start].ctrl & (RQFCR_AND | RQFCR_CLE)) == |
| (RQFCR_AND | RQFCR_CLE)) |
| return start; |
| } |
| return -1; |
| } |
| |
| static int gfar_get_next_cluster_end(int start, struct filer_table *tab) |
| { |
| for (; (start < tab->index) && (start < MAX_FILER_CACHE_IDX - 1); |
| start++) { |
| if ((tab->fe[start].ctrl & (RQFCR_AND | RQFCR_CLE)) == |
| (RQFCR_CLE)) |
| return start; |
| } |
| return -1; |
| } |
| |
| /* Uses hardwares clustering option to reduce |
| * the number of filer table entries |
| */ |
| static void gfar_cluster_filer(struct filer_table *tab) |
| { |
| s32 i = -1, j, iend, jend; |
| |
| while ((i = gfar_get_next_cluster_start(++i, tab)) != -1) { |
| j = i; |
| while ((j = gfar_get_next_cluster_start(++j, tab)) != -1) { |
| /* The cluster entries self and the previous one |
| * (a mask) must be identical! |
| */ |
| if (tab->fe[i].ctrl != tab->fe[j].ctrl) |
| break; |
| if (tab->fe[i].prop != tab->fe[j].prop) |
| break; |
| if (tab->fe[i - 1].ctrl != tab->fe[j - 1].ctrl) |
| break; |
| if (tab->fe[i - 1].prop != tab->fe[j - 1].prop) |
| break; |
| iend = gfar_get_next_cluster_end(i, tab); |
| jend = gfar_get_next_cluster_end(j, tab); |
| if (jend == -1 || iend == -1) |
| break; |
| |
| /* First we make some free space, where our cluster |
| * element should be. Then we copy it there and finally |
| * delete in from its old location. |
| */ |
| if (gfar_expand_filer_entries(iend, (jend - j), tab) == |
| -EINVAL) |
| break; |
| |
| gfar_copy_filer_entries(&(tab->fe[iend + 1]), |
| &(tab->fe[jend + 1]), jend - j); |
| |
| if (gfar_trim_filer_entries(jend - 1, |
| jend + (jend - j), |
| tab) == -EINVAL) |
| return; |
| |
| /* Mask out cluster bit */ |
| tab->fe[iend].ctrl &= ~(RQFCR_CLE); |
| } |
| } |
| } |
| |
| /* Swaps the masked bits of a1<>a2 and b1<>b2 */ |
| static void gfar_swap_bits(struct gfar_filer_entry *a1, |
| struct gfar_filer_entry *a2, |
| struct gfar_filer_entry *b1, |
| struct gfar_filer_entry *b2, u32 mask) |
| { |
| u32 temp[4]; |
| temp[0] = a1->ctrl & mask; |
| temp[1] = a2->ctrl & mask; |
| temp[2] = b1->ctrl & mask; |
| temp[3] = b2->ctrl & mask; |
| |
| a1->ctrl &= ~mask; |
| a2->ctrl &= ~mask; |
| b1->ctrl &= ~mask; |
| b2->ctrl &= ~mask; |
| |
| a1->ctrl |= temp[1]; |
| a2->ctrl |= temp[0]; |
| b1->ctrl |= temp[3]; |
| b2->ctrl |= temp[2]; |
| } |
| |
| /* Generate a list consisting of masks values with their start and |
| * end of validity and block as indicator for parts belonging |
| * together (glued by ANDs) in mask_table |
| */ |
| static u32 gfar_generate_mask_table(struct gfar_mask_entry *mask_table, |
| struct filer_table *tab) |
| { |
| u32 i, and_index = 0, block_index = 1; |
| |
| for (i = 0; i < tab->index; i++) { |
| |
| /* LSByte of control = 0 sets a mask */ |
| if (!(tab->fe[i].ctrl & 0xF)) { |
| mask_table[and_index].mask = tab->fe[i].prop; |
| mask_table[and_index].start = i; |
| mask_table[and_index].block = block_index; |
| if (and_index >= 1) |
| mask_table[and_index - 1].end = i - 1; |
| and_index++; |
| } |
| /* cluster starts and ends will be separated because they should |
| * hold their position |
| */ |
| if (tab->fe[i].ctrl & RQFCR_CLE) |
| block_index++; |
| /* A not set AND indicates the end of a depended block */ |
| if (!(tab->fe[i].ctrl & RQFCR_AND)) |
| block_index++; |
| } |
| |
| mask_table[and_index - 1].end = i - 1; |
| |
| return and_index; |
| } |
| |
| /* Sorts the entries of mask_table by the values of the masks. |
| * Important: The 0xFF80 flags of the first and last entry of a |
| * block must hold their position (which queue, CLusterEnable, ReJEct, |
| * AND) |
| */ |
| static void gfar_sort_mask_table(struct gfar_mask_entry *mask_table, |
| struct filer_table *temp_table, u32 and_index) |
| { |
| /* Pointer to compare function (_asc or _desc) */ |
| int (*gfar_comp)(const void *, const void *); |
| |
| u32 i, size = 0, start = 0, prev = 1; |
| u32 old_first, old_last, new_first, new_last; |
| |
| gfar_comp = &gfar_comp_desc; |
| |
| for (i = 0; i < and_index; i++) { |
| if (prev != mask_table[i].block) { |
| old_first = mask_table[start].start + 1; |
| old_last = mask_table[i - 1].end; |
| sort(mask_table + start, size, |
| sizeof(struct gfar_mask_entry), |
| gfar_comp, &gfar_swap); |
| |
| /* Toggle order for every block. This makes the |
| * thing more efficient! |
| */ |
| if (gfar_comp == gfar_comp_desc) |
| gfar_comp = &gfar_comp_asc; |
| else |
| gfar_comp = &gfar_comp_desc; |
| |
| new_first = mask_table[start].start + 1; |
| new_last = mask_table[i - 1].end; |
| |
| gfar_swap_bits(&temp_table->fe[new_first], |
| &temp_table->fe[old_first], |
| &temp_table->fe[new_last], |
| &temp_table->fe[old_last], |
| RQFCR_QUEUE | RQFCR_CLE | |
| RQFCR_RJE | RQFCR_AND); |
| |
| start = i; |
| size = 0; |
| } |
| size++; |
| prev = mask_table[i].block; |
| } |
| } |
| |
| /* Reduces the number of masks needed in the filer table to save entries |
| * This is done by sorting the masks of a depended block. A depended block is |
| * identified by gluing ANDs or CLE. The sorting order toggles after every |
| * block. Of course entries in scope of a mask must change their location with |
| * it. |
| */ |
| static int gfar_optimize_filer_masks(struct filer_table *tab) |
| { |
| struct filer_table *temp_table; |
| struct gfar_mask_entry *mask_table; |
| |
| u32 and_index = 0, previous_mask = 0, i = 0, j = 0, size = 0; |
| s32 ret = 0; |
| |
| /* We need a copy of the filer table because |
| * we want to change its order |
| */ |
| temp_table = kmemdup(tab, sizeof(*temp_table), GFP_KERNEL); |
| if (temp_table == NULL) |
| return -ENOMEM; |
| |
| mask_table = kcalloc(MAX_FILER_CACHE_IDX / 2 + 1, |
| sizeof(struct gfar_mask_entry), GFP_KERNEL); |
| |
| if (mask_table == NULL) { |
| ret = -ENOMEM; |
| goto end; |
| } |
| |
| and_index = gfar_generate_mask_table(mask_table, tab); |
| |
| gfar_sort_mask_table(mask_table, temp_table, and_index); |
| |
| /* Now we can copy the data from our duplicated filer table to |
| * the real one in the order the mask table says |
| */ |
| for (i = 0; i < and_index; i++) { |
| size = mask_table[i].end - mask_table[i].start + 1; |
| gfar_copy_filer_entries(&(tab->fe[j]), |
| &(temp_table->fe[mask_table[i].start]), size); |
| j += size; |
| } |
| |
| /* And finally we just have to check for duplicated masks and drop the |
| * second ones |
| */ |
| for (i = 0; i < tab->index && i < MAX_FILER_CACHE_IDX; i++) { |
| if (tab->fe[i].ctrl == 0x80) { |
| previous_mask = i++; |
| break; |
| } |
| } |
| for (; i < tab->index && i < MAX_FILER_CACHE_IDX; i++) { |
| if (tab->fe[i].ctrl == 0x80) { |
| if (tab->fe[i].prop == tab->fe[previous_mask].prop) { |
| /* Two identical ones found! |
| * So drop the second one! |
| */ |
| gfar_trim_filer_entries(i, i, tab); |
| } else |
| /* Not identical! */ |
| previous_mask = i; |
| } |
| } |
| |
| kfree(mask_table); |
| end: kfree(temp_table); |
| return ret; |
| } |
| |
| /* Write the bit-pattern from software's buffer to hardware registers */ |
| static int gfar_write_filer_table(struct gfar_private *priv, |
| struct filer_table *tab) |
| { |
| u32 i = 0; |
| if (tab->index > MAX_FILER_IDX - 1) |
| return -EBUSY; |
| |
| /* Fill regular entries */ |
| for (; i < MAX_FILER_IDX - 1 && (tab->fe[i].ctrl | tab->fe[i].ctrl); |
| i++) |
| gfar_write_filer(priv, i, tab->fe[i].ctrl, tab->fe[i].prop); |
| /* Fill the rest with fall-troughs */ |
| for (; i < MAX_FILER_IDX - 1; i++) |
| gfar_write_filer(priv, i, 0x60, 0xFFFFFFFF); |
| /* Last entry must be default accept |
| * because that's what people expect |
| */ |
| gfar_write_filer(priv, i, 0x20, 0x0); |
| |
| return 0; |
| } |
| |
| static int gfar_check_capability(struct ethtool_rx_flow_spec *flow, |
| struct gfar_private *priv) |
| { |
| |
| if (flow->flow_type & FLOW_EXT) { |
| if (~flow->m_ext.data[0] || ~flow->m_ext.data[1]) |
| netdev_warn(priv->ndev, |
| "User-specific data not supported!\n"); |
| if (~flow->m_ext.vlan_etype) |
| netdev_warn(priv->ndev, |
| "VLAN-etype not supported!\n"); |
| } |
| if (flow->flow_type == IP_USER_FLOW) |
| if (flow->h_u.usr_ip4_spec.ip_ver != ETH_RX_NFC_IP4) |
| netdev_warn(priv->ndev, |
| "IP-Version differing from IPv4 not supported!\n"); |
| |
| return 0; |
| } |
| |
| static int gfar_process_filer_changes(struct gfar_private *priv) |
| { |
| struct ethtool_flow_spec_container *j; |
| struct filer_table *tab; |
| s32 i = 0; |
| s32 ret = 0; |
| |
| /* So index is set to zero, too! */ |
| tab = kzalloc(sizeof(*tab), GFP_KERNEL); |
| if (tab == NULL) |
| return -ENOMEM; |
| |
| /* Now convert the existing filer data from flow_spec into |
| * filer tables binary format |
| */ |
| list_for_each_entry(j, &priv->rx_list.list, list) { |
| ret = gfar_convert_to_filer(&j->fs, tab); |
| if (ret == -EBUSY) { |
| netdev_err(priv->ndev, |
| "Rule not added: No free space!\n"); |
| goto end; |
| } |
| if (ret == -1) { |
| netdev_err(priv->ndev, |
| "Rule not added: Unsupported Flow-type!\n"); |
| goto end; |
| } |
| } |
| |
| i = tab->index; |
| |
| /* Optimizations to save entries */ |
| gfar_cluster_filer(tab); |
| gfar_optimize_filer_masks(tab); |
| |
| pr_debug("\tSummary:\n" |
| "\tData on hardware: %d\n" |
| "\tCompression rate: %d%%\n", |
| tab->index, 100 - (100 * tab->index) / i); |
| |
| /* Write everything to hardware */ |
| ret = gfar_write_filer_table(priv, tab); |
| if (ret == -EBUSY) { |
| netdev_err(priv->ndev, "Rule not added: No free space!\n"); |
| goto end; |
| } |
| |
| end: |
| kfree(tab); |
| return ret; |
| } |
| |
| static void gfar_invert_masks(struct ethtool_rx_flow_spec *flow) |
| { |
| u32 i = 0; |
| |
| for (i = 0; i < sizeof(flow->m_u); i++) |
| flow->m_u.hdata[i] ^= 0xFF; |
| |
| flow->m_ext.vlan_etype ^= cpu_to_be16(0xFFFF); |
| flow->m_ext.vlan_tci ^= cpu_to_be16(0xFFFF); |
| flow->m_ext.data[0] ^= cpu_to_be32(~0); |
| flow->m_ext.data[1] ^= cpu_to_be32(~0); |
| } |
| |
| static int gfar_add_cls(struct gfar_private *priv, |
| struct ethtool_rx_flow_spec *flow) |
| { |
| struct ethtool_flow_spec_container *temp, *comp; |
| int ret = 0; |
| |
| temp = kmalloc(sizeof(*temp), GFP_KERNEL); |
| if (temp == NULL) |
| return -ENOMEM; |
| memcpy(&temp->fs, flow, sizeof(temp->fs)); |
| |
| gfar_invert_masks(&temp->fs); |
| ret = gfar_check_capability(&temp->fs, priv); |
| if (ret) |
| goto clean_mem; |
| /* Link in the new element at the right @location */ |
| if (list_empty(&priv->rx_list.list)) { |
| ret = gfar_check_filer_hardware(priv); |
| if (ret != 0) |
| goto clean_mem; |
| list_add(&temp->list, &priv->rx_list.list); |
| goto process; |
| } else { |
| list_for_each_entry(comp, &priv->rx_list.list, list) { |
| if (comp->fs.location > flow->location) { |
| list_add_tail(&temp->list, &comp->list); |
| goto process; |
| } |
| if (comp->fs.location == flow->location) { |
| netdev_err(priv->ndev, |
| "Rule not added: ID %d not free!\n", |
| flow->location); |
| ret = -EBUSY; |
| goto clean_mem; |
| } |
| } |
| list_add_tail(&temp->list, &priv->rx_list.list); |
| } |
| |
| process: |
| ret = gfar_process_filer_changes(priv); |
| if (ret) |
| goto clean_list; |
| priv->rx_list.count++; |
| return ret; |
| |
| clean_list: |
| list_del(&temp->list); |
| clean_mem: |
| kfree(temp); |
| return ret; |
| } |
| |
| static int gfar_del_cls(struct gfar_private *priv, u32 loc) |
| { |
| struct ethtool_flow_spec_container *comp; |
| u32 ret = -EINVAL; |
| |
| if (list_empty(&priv->rx_list.list)) |
| return ret; |
| |
| list_for_each_entry(comp, &priv->rx_list.list, list) { |
| if (comp->fs.location == loc) { |
| list_del(&comp->list); |
| kfree(comp); |
| priv->rx_list.count--; |
| gfar_process_filer_changes(priv); |
| ret = 0; |
| break; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int gfar_get_cls(struct gfar_private *priv, struct ethtool_rxnfc *cmd) |
| { |
| struct ethtool_flow_spec_container *comp; |
| u32 ret = -EINVAL; |
| |
| list_for_each_entry(comp, &priv->rx_list.list, list) { |
| if (comp->fs.location == cmd->fs.location) { |
| memcpy(&cmd->fs, &comp->fs, sizeof(cmd->fs)); |
| gfar_invert_masks(&cmd->fs); |
| ret = 0; |
| break; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int gfar_get_cls_all(struct gfar_private *priv, |
| struct ethtool_rxnfc *cmd, u32 *rule_locs) |
| { |
| struct ethtool_flow_spec_container *comp; |
| u32 i = 0; |
| |
| list_for_each_entry(comp, &priv->rx_list.list, list) { |
| if (i == cmd->rule_cnt) |
| return -EMSGSIZE; |
| rule_locs[i] = comp->fs.location; |
| i++; |
| } |
| |
| cmd->data = MAX_FILER_IDX; |
| cmd->rule_cnt = i; |
| |
| return 0; |
| } |
| |
| static int gfar_set_nfc(struct net_device *dev, struct ethtool_rxnfc *cmd) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| int ret = 0; |
| |
| if (test_bit(GFAR_RESETTING, &priv->state)) |
| return -EBUSY; |
| |
| mutex_lock(&priv->rx_queue_access); |
| |
| switch (cmd->cmd) { |
| case ETHTOOL_SRXFH: |
| ret = gfar_set_hash_opts(priv, cmd); |
| break; |
| case ETHTOOL_SRXCLSRLINS: |
| if ((cmd->fs.ring_cookie != RX_CLS_FLOW_DISC && |
| cmd->fs.ring_cookie >= priv->num_rx_queues) || |
| cmd->fs.location >= MAX_FILER_IDX) { |
| ret = -EINVAL; |
| break; |
| } |
| ret = gfar_add_cls(priv, &cmd->fs); |
| break; |
| case ETHTOOL_SRXCLSRLDEL: |
| ret = gfar_del_cls(priv, cmd->fs.location); |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| mutex_unlock(&priv->rx_queue_access); |
| |
| return ret; |
| } |
| |
| static int gfar_get_nfc(struct net_device *dev, struct ethtool_rxnfc *cmd, |
| u32 *rule_locs) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| int ret = 0; |
| |
| switch (cmd->cmd) { |
| case ETHTOOL_GRXRINGS: |
| cmd->data = priv->num_rx_queues; |
| break; |
| case ETHTOOL_GRXCLSRLCNT: |
| cmd->rule_cnt = priv->rx_list.count; |
| break; |
| case ETHTOOL_GRXCLSRULE: |
| ret = gfar_get_cls(priv, cmd); |
| break; |
| case ETHTOOL_GRXCLSRLALL: |
| ret = gfar_get_cls_all(priv, cmd, rule_locs); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| |
| return ret; |
| } |
| |
| int gfar_phc_index = -1; |
| EXPORT_SYMBOL(gfar_phc_index); |
| |
| static int gfar_get_ts_info(struct net_device *dev, |
| struct ethtool_ts_info *info) |
| { |
| struct gfar_private *priv = netdev_priv(dev); |
| |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER)) { |
| info->so_timestamping = SOF_TIMESTAMPING_RX_SOFTWARE | |
| SOF_TIMESTAMPING_SOFTWARE; |
| info->phc_index = -1; |
| return 0; |
| } |
| info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE | |
| SOF_TIMESTAMPING_RX_HARDWARE | |
| SOF_TIMESTAMPING_RAW_HARDWARE; |
| info->phc_index = gfar_phc_index; |
| info->tx_types = (1 << HWTSTAMP_TX_OFF) | |
| (1 << HWTSTAMP_TX_ON); |
| info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) | |
| (1 << HWTSTAMP_FILTER_ALL); |
| return 0; |
| } |
| |
| const struct ethtool_ops gfar_ethtool_ops = { |
| .get_settings = gfar_gsettings, |
| .set_settings = gfar_ssettings, |
| .get_drvinfo = gfar_gdrvinfo, |
| .get_regs_len = gfar_reglen, |
| .get_regs = gfar_get_regs, |
| .get_link = ethtool_op_get_link, |
| .get_coalesce = gfar_gcoalesce, |
| .set_coalesce = gfar_scoalesce, |
| .get_ringparam = gfar_gringparam, |
| .set_ringparam = gfar_sringparam, |
| .get_pauseparam = gfar_gpauseparam, |
| .set_pauseparam = gfar_spauseparam, |
| .get_strings = gfar_gstrings, |
| .get_sset_count = gfar_sset_count, |
| .get_ethtool_stats = gfar_fill_stats, |
| .get_msglevel = gfar_get_msglevel, |
| .set_msglevel = gfar_set_msglevel, |
| #ifdef CONFIG_PM |
| .get_wol = gfar_get_wol, |
| .set_wol = gfar_set_wol, |
| #endif |
| .set_rxnfc = gfar_set_nfc, |
| .get_rxnfc = gfar_get_nfc, |
| .get_ts_info = gfar_get_ts_info, |
| }; |