blob: 73d34e77c39c136b0066236b7b8a2f43d8b9aa0c [file] [log] [blame]
config FRAME_POINTER
def_bool n
config ZONE_DMA
def_bool y
config XTENSA
def_bool y
select HAVE_IDE
select GENERIC_ATOMIC64
select HAVE_GENERIC_HARDIRQS
select GENERIC_IRQ_SHOW
select GENERIC_CPU_DEVICES
select MODULES_USE_ELF_RELA
select GENERIC_PCI_IOMAP
select GENERIC_KERNEL_THREAD
select GENERIC_KERNEL_EXECVE
select ARCH_WANT_OPTIONAL_GPIOLIB
select CLONE_BACKWARDS
select IRQ_DOMAIN
help
Xtensa processors are 32-bit RISC machines designed by Tensilica
primarily for embedded systems. These processors are both
configurable and extensible. The Linux port to the Xtensa
architecture supports all processor configurations and extensions,
with reasonable minimum requirements. The Xtensa Linux project has
a home page at <http://xtensa.sourceforge.net/>.
config RWSEM_XCHGADD_ALGORITHM
def_bool y
config GENERIC_HWEIGHT
def_bool y
config GENERIC_GPIO
def_bool y
config ARCH_HAS_ILOG2_U32
def_bool n
config ARCH_HAS_ILOG2_U64
def_bool n
config NO_IOPORT
def_bool n
config HZ
int
default 100
source "init/Kconfig"
source "kernel/Kconfig.freezer"
config MMU
def_bool n
config VARIANT_IRQ_SWITCH
def_bool n
menu "Processor type and features"
choice
prompt "Xtensa Processor Configuration"
default XTENSA_VARIANT_FSF
config XTENSA_VARIANT_FSF
bool "fsf - default (not generic) configuration"
select MMU
config XTENSA_VARIANT_DC232B
bool "dc232b - Diamond 232L Standard Core Rev.B (LE)"
select MMU
help
This variant refers to Tensilica's Diamond 232L Standard core Rev.B (LE).
config XTENSA_VARIANT_S6000
bool "s6000 - Stretch software configurable processor"
select VARIANT_IRQ_SWITCH
select ARCH_REQUIRE_GPIOLIB
select XTENSA_CALIBRATE_CCOUNT
endchoice
config XTENSA_UNALIGNED_USER
bool "Unaligned memory access in use space"
help
The Xtensa architecture currently does not handle unaligned
memory accesses in hardware but through an exception handler.
Per default, unaligned memory accesses are disabled in user space.
Say Y here to enable unaligned memory access in user space.
source "kernel/Kconfig.preempt"
config MATH_EMULATION
bool "Math emulation"
help
Can we use information of configuration file?
endmenu
config XTENSA_CALIBRATE_CCOUNT
def_bool n
help
On some platforms (XT2000, for example), the CPU clock rate can
vary. The frequency can be determined, however, by measuring
against a well known, fixed frequency, such as an UART oscillator.
config SERIAL_CONSOLE
def_bool n
config XTENSA_ISS_NETWORK
def_bool n
menu "Bus options"
config PCI
bool "PCI support"
default y
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
VESA. If you have PCI, say Y, otherwise N.
source "drivers/pci/Kconfig"
endmenu
menu "Platform options"
choice
prompt "Xtensa System Type"
default XTENSA_PLATFORM_ISS
config XTENSA_PLATFORM_ISS
bool "ISS"
select XTENSA_CALIBRATE_CCOUNT
select SERIAL_CONSOLE
select XTENSA_ISS_NETWORK
help
ISS is an acronym for Tensilica's Instruction Set Simulator.
config XTENSA_PLATFORM_XT2000
bool "XT2000"
help
XT2000 is the name of Tensilica's feature-rich emulation platform.
This hardware is capable of running a full Linux distribution.
config XTENSA_PLATFORM_S6105
bool "S6105"
select SERIAL_CONSOLE
select NO_IOPORT
config XTENSA_PLATFORM_XTFPGA
bool "XTFPGA"
select SERIAL_CONSOLE
select ETHOC
select XTENSA_CALIBRATE_CCOUNT
help
XTFPGA is the name of Tensilica board family (LX60, LX110, LX200, ML605).
This hardware is capable of running a full Linux distribution.
endchoice
config XTENSA_CPU_CLOCK
int "CPU clock rate [MHz]"
depends on !XTENSA_CALIBRATE_CCOUNT
default 16
config GENERIC_CALIBRATE_DELAY
bool "Auto calibration of the BogoMIPS value"
help
The BogoMIPS value can easily be derived from the CPU frequency.
config CMDLINE_BOOL
bool "Default bootloader kernel arguments"
config CMDLINE
string "Initial kernel command string"
depends on CMDLINE_BOOL
default "console=ttyS0,38400 root=/dev/ram"
help
On some architectures (EBSA110 and CATS), there is currently no way
for the boot loader to pass arguments to the kernel. For these
architectures, you should supply some command-line options at build
time by entering them here. As a minimum, you should specify the
memory size and the root device (e.g., mem=64M root=/dev/nfs).
config USE_OF
bool "Flattened Device Tree support"
select OF
select OF_EARLY_FLATTREE
help
Include support for flattened device tree machine descriptions.
config BUILTIN_DTB
string "DTB to build into the kernel image"
depends on OF
source "mm/Kconfig"
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
endmenu
menu "Executable file formats"
# only elf supported
config KCORE_ELF
def_bool y
depends on PROC_FS
help
If you enabled support for /proc file system then the file
/proc/kcore will contain the kernel core image in ELF format. This
can be used in gdb:
$ cd /usr/src/linux ; gdb vmlinux /proc/kcore
This is especially useful if you have compiled the kernel with the
"-g" option to preserve debugging information. It is mainly used
for examining kernel data structures on the live kernel.
source "fs/Kconfig.binfmt"
endmenu
source "net/Kconfig"
source "drivers/Kconfig"
source "fs/Kconfig"
source "arch/xtensa/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"