| /* |
| * xHCI host controller driver |
| * |
| * Copyright (C) 2008 Intel Corp. |
| * |
| * Author: Sarah Sharp |
| * Some code borrowed from the Linux EHCI driver. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY |
| * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License |
| * for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software Foundation, |
| * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| /* |
| * Ring initialization rules: |
| * 1. Each segment is initialized to zero, except for link TRBs. |
| * 2. Ring cycle state = 0. This represents Producer Cycle State (PCS) or |
| * Consumer Cycle State (CCS), depending on ring function. |
| * 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment. |
| * |
| * Ring behavior rules: |
| * 1. A ring is empty if enqueue == dequeue. This means there will always be at |
| * least one free TRB in the ring. This is useful if you want to turn that |
| * into a link TRB and expand the ring. |
| * 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a |
| * link TRB, then load the pointer with the address in the link TRB. If the |
| * link TRB had its toggle bit set, you may need to update the ring cycle |
| * state (see cycle bit rules). You may have to do this multiple times |
| * until you reach a non-link TRB. |
| * 3. A ring is full if enqueue++ (for the definition of increment above) |
| * equals the dequeue pointer. |
| * |
| * Cycle bit rules: |
| * 1. When a consumer increments a dequeue pointer and encounters a toggle bit |
| * in a link TRB, it must toggle the ring cycle state. |
| * 2. When a producer increments an enqueue pointer and encounters a toggle bit |
| * in a link TRB, it must toggle the ring cycle state. |
| * |
| * Producer rules: |
| * 1. Check if ring is full before you enqueue. |
| * 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing. |
| * Update enqueue pointer between each write (which may update the ring |
| * cycle state). |
| * 3. Notify consumer. If SW is producer, it rings the doorbell for command |
| * and endpoint rings. If HC is the producer for the event ring, |
| * and it generates an interrupt according to interrupt modulation rules. |
| * |
| * Consumer rules: |
| * 1. Check if TRB belongs to you. If the cycle bit == your ring cycle state, |
| * the TRB is owned by the consumer. |
| * 2. Update dequeue pointer (which may update the ring cycle state) and |
| * continue processing TRBs until you reach a TRB which is not owned by you. |
| * 3. Notify the producer. SW is the consumer for the event ring, and it |
| * updates event ring dequeue pointer. HC is the consumer for the command and |
| * endpoint rings; it generates events on the event ring for these. |
| */ |
| |
| #include <linux/scatterlist.h> |
| #include "xhci.h" |
| |
| /* |
| * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA |
| * address of the TRB. |
| */ |
| dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg, |
| union xhci_trb *trb) |
| { |
| unsigned long segment_offset; |
| |
| if (!seg || !trb || trb < seg->trbs) |
| return 0; |
| /* offset in TRBs */ |
| segment_offset = trb - seg->trbs; |
| if (segment_offset > TRBS_PER_SEGMENT) |
| return 0; |
| return seg->dma + (segment_offset * sizeof(*trb)); |
| } |
| |
| /* Does this link TRB point to the first segment in a ring, |
| * or was the previous TRB the last TRB on the last segment in the ERST? |
| */ |
| static inline bool last_trb_on_last_seg(struct xhci_hcd *xhci, struct xhci_ring *ring, |
| struct xhci_segment *seg, union xhci_trb *trb) |
| { |
| if (ring == xhci->event_ring) |
| return (trb == &seg->trbs[TRBS_PER_SEGMENT]) && |
| (seg->next == xhci->event_ring->first_seg); |
| else |
| return trb->link.control & LINK_TOGGLE; |
| } |
| |
| /* Is this TRB a link TRB or was the last TRB the last TRB in this event ring |
| * segment? I.e. would the updated event TRB pointer step off the end of the |
| * event seg? |
| */ |
| static inline int last_trb(struct xhci_hcd *xhci, struct xhci_ring *ring, |
| struct xhci_segment *seg, union xhci_trb *trb) |
| { |
| if (ring == xhci->event_ring) |
| return trb == &seg->trbs[TRBS_PER_SEGMENT]; |
| else |
| return (trb->link.control & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK); |
| } |
| |
| /* Updates trb to point to the next TRB in the ring, and updates seg if the next |
| * TRB is in a new segment. This does not skip over link TRBs, and it does not |
| * effect the ring dequeue or enqueue pointers. |
| */ |
| static void next_trb(struct xhci_hcd *xhci, |
| struct xhci_ring *ring, |
| struct xhci_segment **seg, |
| union xhci_trb **trb) |
| { |
| if (last_trb(xhci, ring, *seg, *trb)) { |
| *seg = (*seg)->next; |
| *trb = ((*seg)->trbs); |
| } else { |
| *trb = (*trb)++; |
| } |
| } |
| |
| /* |
| * See Cycle bit rules. SW is the consumer for the event ring only. |
| * Don't make a ring full of link TRBs. That would be dumb and this would loop. |
| */ |
| static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer) |
| { |
| union xhci_trb *next = ++(ring->dequeue); |
| unsigned long long addr; |
| |
| ring->deq_updates++; |
| /* Update the dequeue pointer further if that was a link TRB or we're at |
| * the end of an event ring segment (which doesn't have link TRBS) |
| */ |
| while (last_trb(xhci, ring, ring->deq_seg, next)) { |
| if (consumer && last_trb_on_last_seg(xhci, ring, ring->deq_seg, next)) { |
| ring->cycle_state = (ring->cycle_state ? 0 : 1); |
| if (!in_interrupt()) |
| xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n", |
| ring, |
| (unsigned int) ring->cycle_state); |
| } |
| ring->deq_seg = ring->deq_seg->next; |
| ring->dequeue = ring->deq_seg->trbs; |
| next = ring->dequeue; |
| } |
| addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue); |
| if (ring == xhci->event_ring) |
| xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr); |
| else if (ring == xhci->cmd_ring) |
| xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr); |
| else |
| xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr); |
| } |
| |
| /* |
| * See Cycle bit rules. SW is the consumer for the event ring only. |
| * Don't make a ring full of link TRBs. That would be dumb and this would loop. |
| * |
| * If we've just enqueued a TRB that is in the middle of a TD (meaning the |
| * chain bit is set), then set the chain bit in all the following link TRBs. |
| * If we've enqueued the last TRB in a TD, make sure the following link TRBs |
| * have their chain bit cleared (so that each Link TRB is a separate TD). |
| * |
| * Section 6.4.4.1 of the 0.95 spec says link TRBs cannot have the chain bit |
| * set, but other sections talk about dealing with the chain bit set. |
| * Assume section 6.4.4.1 is wrong, and the chain bit can be set in a Link TRB. |
| */ |
| static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer) |
| { |
| u32 chain; |
| union xhci_trb *next; |
| unsigned long long addr; |
| |
| chain = ring->enqueue->generic.field[3] & TRB_CHAIN; |
| next = ++(ring->enqueue); |
| |
| ring->enq_updates++; |
| /* Update the dequeue pointer further if that was a link TRB or we're at |
| * the end of an event ring segment (which doesn't have link TRBS) |
| */ |
| while (last_trb(xhci, ring, ring->enq_seg, next)) { |
| if (!consumer) { |
| if (ring != xhci->event_ring) { |
| next->link.control &= ~TRB_CHAIN; |
| next->link.control |= chain; |
| /* Give this link TRB to the hardware */ |
| wmb(); |
| if (next->link.control & TRB_CYCLE) |
| next->link.control &= (u32) ~TRB_CYCLE; |
| else |
| next->link.control |= (u32) TRB_CYCLE; |
| } |
| /* Toggle the cycle bit after the last ring segment. */ |
| if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) { |
| ring->cycle_state = (ring->cycle_state ? 0 : 1); |
| if (!in_interrupt()) |
| xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n", |
| ring, |
| (unsigned int) ring->cycle_state); |
| } |
| } |
| ring->enq_seg = ring->enq_seg->next; |
| ring->enqueue = ring->enq_seg->trbs; |
| next = ring->enqueue; |
| } |
| addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue); |
| if (ring == xhci->event_ring) |
| xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr); |
| else if (ring == xhci->cmd_ring) |
| xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr); |
| else |
| xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr); |
| } |
| |
| /* |
| * Check to see if there's room to enqueue num_trbs on the ring. See rules |
| * above. |
| * FIXME: this would be simpler and faster if we just kept track of the number |
| * of free TRBs in a ring. |
| */ |
| static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, |
| unsigned int num_trbs) |
| { |
| int i; |
| union xhci_trb *enq = ring->enqueue; |
| struct xhci_segment *enq_seg = ring->enq_seg; |
| |
| /* Check if ring is empty */ |
| if (enq == ring->dequeue) |
| return 1; |
| /* Make sure there's an extra empty TRB available */ |
| for (i = 0; i <= num_trbs; ++i) { |
| if (enq == ring->dequeue) |
| return 0; |
| enq++; |
| while (last_trb(xhci, ring, enq_seg, enq)) { |
| enq_seg = enq_seg->next; |
| enq = enq_seg->trbs; |
| } |
| } |
| return 1; |
| } |
| |
| void xhci_set_hc_event_deq(struct xhci_hcd *xhci) |
| { |
| u64 temp; |
| dma_addr_t deq; |
| |
| deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, |
| xhci->event_ring->dequeue); |
| if (deq == 0 && !in_interrupt()) |
| xhci_warn(xhci, "WARN something wrong with SW event ring " |
| "dequeue ptr.\n"); |
| /* Update HC event ring dequeue pointer */ |
| temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); |
| temp &= ERST_PTR_MASK; |
| /* Don't clear the EHB bit (which is RW1C) because |
| * there might be more events to service. |
| */ |
| temp &= ~ERST_EHB; |
| xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); |
| xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, |
| &xhci->ir_set->erst_dequeue); |
| } |
| |
| /* Ring the host controller doorbell after placing a command on the ring */ |
| void xhci_ring_cmd_db(struct xhci_hcd *xhci) |
| { |
| u32 temp; |
| |
| xhci_dbg(xhci, "// Ding dong!\n"); |
| temp = xhci_readl(xhci, &xhci->dba->doorbell[0]) & DB_MASK; |
| xhci_writel(xhci, temp | DB_TARGET_HOST, &xhci->dba->doorbell[0]); |
| /* Flush PCI posted writes */ |
| xhci_readl(xhci, &xhci->dba->doorbell[0]); |
| } |
| |
| static void ring_ep_doorbell(struct xhci_hcd *xhci, |
| unsigned int slot_id, |
| unsigned int ep_index) |
| { |
| struct xhci_ring *ep_ring; |
| u32 field; |
| __u32 __iomem *db_addr = &xhci->dba->doorbell[slot_id]; |
| |
| ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; |
| /* Don't ring the doorbell for this endpoint if there are pending |
| * cancellations because the we don't want to interrupt processing. |
| */ |
| if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING) |
| && !(ep_ring->state & EP_HALTED)) { |
| field = xhci_readl(xhci, db_addr) & DB_MASK; |
| xhci_writel(xhci, field | EPI_TO_DB(ep_index), db_addr); |
| /* Flush PCI posted writes - FIXME Matthew Wilcox says this |
| * isn't time-critical and we shouldn't make the CPU wait for |
| * the flush. |
| */ |
| xhci_readl(xhci, db_addr); |
| } |
| } |
| |
| /* |
| * Find the segment that trb is in. Start searching in start_seg. |
| * If we must move past a segment that has a link TRB with a toggle cycle state |
| * bit set, then we will toggle the value pointed at by cycle_state. |
| */ |
| static struct xhci_segment *find_trb_seg( |
| struct xhci_segment *start_seg, |
| union xhci_trb *trb, int *cycle_state) |
| { |
| struct xhci_segment *cur_seg = start_seg; |
| struct xhci_generic_trb *generic_trb; |
| |
| while (cur_seg->trbs > trb || |
| &cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) { |
| generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic; |
| if (TRB_TYPE(generic_trb->field[3]) == TRB_LINK && |
| (generic_trb->field[3] & LINK_TOGGLE)) |
| *cycle_state = ~(*cycle_state) & 0x1; |
| cur_seg = cur_seg->next; |
| if (cur_seg == start_seg) |
| /* Looped over the entire list. Oops! */ |
| return 0; |
| } |
| return cur_seg; |
| } |
| |
| struct dequeue_state { |
| struct xhci_segment *new_deq_seg; |
| union xhci_trb *new_deq_ptr; |
| int new_cycle_state; |
| }; |
| |
| /* |
| * Move the xHC's endpoint ring dequeue pointer past cur_td. |
| * Record the new state of the xHC's endpoint ring dequeue segment, |
| * dequeue pointer, and new consumer cycle state in state. |
| * Update our internal representation of the ring's dequeue pointer. |
| * |
| * We do this in three jumps: |
| * - First we update our new ring state to be the same as when the xHC stopped. |
| * - Then we traverse the ring to find the segment that contains |
| * the last TRB in the TD. We toggle the xHC's new cycle state when we pass |
| * any link TRBs with the toggle cycle bit set. |
| * - Finally we move the dequeue state one TRB further, toggling the cycle bit |
| * if we've moved it past a link TRB with the toggle cycle bit set. |
| */ |
| static void find_new_dequeue_state(struct xhci_hcd *xhci, |
| unsigned int slot_id, unsigned int ep_index, |
| struct xhci_td *cur_td, struct dequeue_state *state) |
| { |
| struct xhci_virt_device *dev = xhci->devs[slot_id]; |
| struct xhci_ring *ep_ring = dev->ep_rings[ep_index]; |
| struct xhci_generic_trb *trb; |
| struct xhci_ep_ctx *ep_ctx; |
| |
| state->new_cycle_state = 0; |
| state->new_deq_seg = find_trb_seg(cur_td->start_seg, |
| ep_ring->stopped_trb, |
| &state->new_cycle_state); |
| if (!state->new_deq_seg) |
| BUG(); |
| /* Dig out the cycle state saved by the xHC during the stop ep cmd */ |
| ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); |
| state->new_cycle_state = 0x1 & ep_ctx->deq; |
| |
| state->new_deq_ptr = cur_td->last_trb; |
| state->new_deq_seg = find_trb_seg(state->new_deq_seg, |
| state->new_deq_ptr, |
| &state->new_cycle_state); |
| if (!state->new_deq_seg) |
| BUG(); |
| |
| trb = &state->new_deq_ptr->generic; |
| if (TRB_TYPE(trb->field[3]) == TRB_LINK && |
| (trb->field[3] & LINK_TOGGLE)) |
| state->new_cycle_state = ~(state->new_cycle_state) & 0x1; |
| next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr); |
| |
| /* Don't update the ring cycle state for the producer (us). */ |
| ep_ring->dequeue = state->new_deq_ptr; |
| ep_ring->deq_seg = state->new_deq_seg; |
| } |
| |
| static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, |
| struct xhci_td *cur_td) |
| { |
| struct xhci_segment *cur_seg; |
| union xhci_trb *cur_trb; |
| |
| for (cur_seg = cur_td->start_seg, cur_trb = cur_td->first_trb; |
| true; |
| next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) { |
| if ((cur_trb->generic.field[3] & TRB_TYPE_BITMASK) == |
| TRB_TYPE(TRB_LINK)) { |
| /* Unchain any chained Link TRBs, but |
| * leave the pointers intact. |
| */ |
| cur_trb->generic.field[3] &= ~TRB_CHAIN; |
| xhci_dbg(xhci, "Cancel (unchain) link TRB\n"); |
| xhci_dbg(xhci, "Address = %p (0x%llx dma); " |
| "in seg %p (0x%llx dma)\n", |
| cur_trb, |
| (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb), |
| cur_seg, |
| (unsigned long long)cur_seg->dma); |
| } else { |
| cur_trb->generic.field[0] = 0; |
| cur_trb->generic.field[1] = 0; |
| cur_trb->generic.field[2] = 0; |
| /* Preserve only the cycle bit of this TRB */ |
| cur_trb->generic.field[3] &= TRB_CYCLE; |
| cur_trb->generic.field[3] |= TRB_TYPE(TRB_TR_NOOP); |
| xhci_dbg(xhci, "Cancel TRB %p (0x%llx dma) " |
| "in seg %p (0x%llx dma)\n", |
| cur_trb, |
| (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb), |
| cur_seg, |
| (unsigned long long)cur_seg->dma); |
| } |
| if (cur_trb == cur_td->last_trb) |
| break; |
| } |
| } |
| |
| static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, |
| unsigned int ep_index, struct xhci_segment *deq_seg, |
| union xhci_trb *deq_ptr, u32 cycle_state); |
| |
| /* |
| * When we get a command completion for a Stop Endpoint Command, we need to |
| * unlink any cancelled TDs from the ring. There are two ways to do that: |
| * |
| * 1. If the HW was in the middle of processing the TD that needs to be |
| * cancelled, then we must move the ring's dequeue pointer past the last TRB |
| * in the TD with a Set Dequeue Pointer Command. |
| * 2. Otherwise, we turn all the TRBs in the TD into No-op TRBs (with the chain |
| * bit cleared) so that the HW will skip over them. |
| */ |
| static void handle_stopped_endpoint(struct xhci_hcd *xhci, |
| union xhci_trb *trb) |
| { |
| unsigned int slot_id; |
| unsigned int ep_index; |
| struct xhci_ring *ep_ring; |
| struct list_head *entry; |
| struct xhci_td *cur_td = 0; |
| struct xhci_td *last_unlinked_td; |
| |
| struct dequeue_state deq_state; |
| #ifdef CONFIG_USB_HCD_STAT |
| ktime_t stop_time = ktime_get(); |
| #endif |
| |
| memset(&deq_state, 0, sizeof(deq_state)); |
| slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); |
| ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); |
| ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; |
| |
| if (list_empty(&ep_ring->cancelled_td_list)) |
| return; |
| |
| /* Fix up the ep ring first, so HW stops executing cancelled TDs. |
| * We have the xHCI lock, so nothing can modify this list until we drop |
| * it. We're also in the event handler, so we can't get re-interrupted |
| * if another Stop Endpoint command completes |
| */ |
| list_for_each(entry, &ep_ring->cancelled_td_list) { |
| cur_td = list_entry(entry, struct xhci_td, cancelled_td_list); |
| xhci_dbg(xhci, "Cancelling TD starting at %p, 0x%llx (dma).\n", |
| cur_td->first_trb, |
| (unsigned long long)xhci_trb_virt_to_dma(cur_td->start_seg, cur_td->first_trb)); |
| /* |
| * If we stopped on the TD we need to cancel, then we have to |
| * move the xHC endpoint ring dequeue pointer past this TD. |
| */ |
| if (cur_td == ep_ring->stopped_td) |
| find_new_dequeue_state(xhci, slot_id, ep_index, cur_td, |
| &deq_state); |
| else |
| td_to_noop(xhci, ep_ring, cur_td); |
| /* |
| * The event handler won't see a completion for this TD anymore, |
| * so remove it from the endpoint ring's TD list. Keep it in |
| * the cancelled TD list for URB completion later. |
| */ |
| list_del(&cur_td->td_list); |
| ep_ring->cancels_pending--; |
| } |
| last_unlinked_td = cur_td; |
| |
| /* If necessary, queue a Set Transfer Ring Dequeue Pointer command */ |
| if (deq_state.new_deq_ptr && deq_state.new_deq_seg) { |
| xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), " |
| "new deq ptr = %p (0x%llx dma), new cycle = %u\n", |
| deq_state.new_deq_seg, |
| (unsigned long long)deq_state.new_deq_seg->dma, |
| deq_state.new_deq_ptr, |
| (unsigned long long)xhci_trb_virt_to_dma(deq_state.new_deq_seg, deq_state.new_deq_ptr), |
| deq_state.new_cycle_state); |
| queue_set_tr_deq(xhci, slot_id, ep_index, |
| deq_state.new_deq_seg, |
| deq_state.new_deq_ptr, |
| (u32) deq_state.new_cycle_state); |
| /* Stop the TD queueing code from ringing the doorbell until |
| * this command completes. The HC won't set the dequeue pointer |
| * if the ring is running, and ringing the doorbell starts the |
| * ring running. |
| */ |
| ep_ring->state |= SET_DEQ_PENDING; |
| xhci_ring_cmd_db(xhci); |
| } else { |
| /* Otherwise just ring the doorbell to restart the ring */ |
| ring_ep_doorbell(xhci, slot_id, ep_index); |
| } |
| |
| /* |
| * Drop the lock and complete the URBs in the cancelled TD list. |
| * New TDs to be cancelled might be added to the end of the list before |
| * we can complete all the URBs for the TDs we already unlinked. |
| * So stop when we've completed the URB for the last TD we unlinked. |
| */ |
| do { |
| cur_td = list_entry(ep_ring->cancelled_td_list.next, |
| struct xhci_td, cancelled_td_list); |
| list_del(&cur_td->cancelled_td_list); |
| |
| /* Clean up the cancelled URB */ |
| #ifdef CONFIG_USB_HCD_STAT |
| hcd_stat_update(xhci->tp_stat, cur_td->urb->actual_length, |
| ktime_sub(stop_time, cur_td->start_time)); |
| #endif |
| cur_td->urb->hcpriv = NULL; |
| usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), cur_td->urb); |
| |
| xhci_dbg(xhci, "Giveback cancelled URB %p\n", cur_td->urb); |
| spin_unlock(&xhci->lock); |
| /* Doesn't matter what we pass for status, since the core will |
| * just overwrite it (because the URB has been unlinked). |
| */ |
| usb_hcd_giveback_urb(xhci_to_hcd(xhci), cur_td->urb, 0); |
| kfree(cur_td); |
| |
| spin_lock(&xhci->lock); |
| } while (cur_td != last_unlinked_td); |
| |
| /* Return to the event handler with xhci->lock re-acquired */ |
| } |
| |
| /* |
| * When we get a completion for a Set Transfer Ring Dequeue Pointer command, |
| * we need to clear the set deq pending flag in the endpoint ring state, so that |
| * the TD queueing code can ring the doorbell again. We also need to ring the |
| * endpoint doorbell to restart the ring, but only if there aren't more |
| * cancellations pending. |
| */ |
| static void handle_set_deq_completion(struct xhci_hcd *xhci, |
| struct xhci_event_cmd *event, |
| union xhci_trb *trb) |
| { |
| unsigned int slot_id; |
| unsigned int ep_index; |
| struct xhci_ring *ep_ring; |
| struct xhci_virt_device *dev; |
| struct xhci_ep_ctx *ep_ctx; |
| struct xhci_slot_ctx *slot_ctx; |
| |
| slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); |
| ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); |
| dev = xhci->devs[slot_id]; |
| ep_ring = dev->ep_rings[ep_index]; |
| ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); |
| slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx); |
| |
| if (GET_COMP_CODE(event->status) != COMP_SUCCESS) { |
| unsigned int ep_state; |
| unsigned int slot_state; |
| |
| switch (GET_COMP_CODE(event->status)) { |
| case COMP_TRB_ERR: |
| xhci_warn(xhci, "WARN Set TR Deq Ptr cmd invalid because " |
| "of stream ID configuration\n"); |
| break; |
| case COMP_CTX_STATE: |
| xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due " |
| "to incorrect slot or ep state.\n"); |
| ep_state = ep_ctx->ep_info; |
| ep_state &= EP_STATE_MASK; |
| slot_state = slot_ctx->dev_state; |
| slot_state = GET_SLOT_STATE(slot_state); |
| xhci_dbg(xhci, "Slot state = %u, EP state = %u\n", |
| slot_state, ep_state); |
| break; |
| case COMP_EBADSLT: |
| xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed because " |
| "slot %u was not enabled.\n", slot_id); |
| break; |
| default: |
| xhci_warn(xhci, "WARN Set TR Deq Ptr cmd with unknown " |
| "completion code of %u.\n", |
| GET_COMP_CODE(event->status)); |
| break; |
| } |
| /* OK what do we do now? The endpoint state is hosed, and we |
| * should never get to this point if the synchronization between |
| * queueing, and endpoint state are correct. This might happen |
| * if the device gets disconnected after we've finished |
| * cancelling URBs, which might not be an error... |
| */ |
| } else { |
| xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n", |
| ep_ctx->deq); |
| } |
| |
| ep_ring->state &= ~SET_DEQ_PENDING; |
| ring_ep_doorbell(xhci, slot_id, ep_index); |
| } |
| |
| static void handle_reset_ep_completion(struct xhci_hcd *xhci, |
| struct xhci_event_cmd *event, |
| union xhci_trb *trb) |
| { |
| int slot_id; |
| unsigned int ep_index; |
| |
| slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); |
| ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); |
| /* This command will only fail if the endpoint wasn't halted, |
| * but we don't care. |
| */ |
| xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n", |
| (unsigned int) GET_COMP_CODE(event->status)); |
| |
| /* Clear our internal halted state and restart the ring */ |
| xhci->devs[slot_id]->ep_rings[ep_index]->state &= ~EP_HALTED; |
| ring_ep_doorbell(xhci, slot_id, ep_index); |
| } |
| |
| static void handle_cmd_completion(struct xhci_hcd *xhci, |
| struct xhci_event_cmd *event) |
| { |
| int slot_id = TRB_TO_SLOT_ID(event->flags); |
| u64 cmd_dma; |
| dma_addr_t cmd_dequeue_dma; |
| |
| cmd_dma = event->cmd_trb; |
| cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, |
| xhci->cmd_ring->dequeue); |
| /* Is the command ring deq ptr out of sync with the deq seg ptr? */ |
| if (cmd_dequeue_dma == 0) { |
| xhci->error_bitmask |= 1 << 4; |
| return; |
| } |
| /* Does the DMA address match our internal dequeue pointer address? */ |
| if (cmd_dma != (u64) cmd_dequeue_dma) { |
| xhci->error_bitmask |= 1 << 5; |
| return; |
| } |
| switch (xhci->cmd_ring->dequeue->generic.field[3] & TRB_TYPE_BITMASK) { |
| case TRB_TYPE(TRB_ENABLE_SLOT): |
| if (GET_COMP_CODE(event->status) == COMP_SUCCESS) |
| xhci->slot_id = slot_id; |
| else |
| xhci->slot_id = 0; |
| complete(&xhci->addr_dev); |
| break; |
| case TRB_TYPE(TRB_DISABLE_SLOT): |
| if (xhci->devs[slot_id]) |
| xhci_free_virt_device(xhci, slot_id); |
| break; |
| case TRB_TYPE(TRB_CONFIG_EP): |
| xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status); |
| complete(&xhci->devs[slot_id]->cmd_completion); |
| break; |
| case TRB_TYPE(TRB_ADDR_DEV): |
| xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status); |
| complete(&xhci->addr_dev); |
| break; |
| case TRB_TYPE(TRB_STOP_RING): |
| handle_stopped_endpoint(xhci, xhci->cmd_ring->dequeue); |
| break; |
| case TRB_TYPE(TRB_SET_DEQ): |
| handle_set_deq_completion(xhci, event, xhci->cmd_ring->dequeue); |
| break; |
| case TRB_TYPE(TRB_CMD_NOOP): |
| ++xhci->noops_handled; |
| break; |
| case TRB_TYPE(TRB_RESET_EP): |
| handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue); |
| break; |
| default: |
| /* Skip over unknown commands on the event ring */ |
| xhci->error_bitmask |= 1 << 6; |
| break; |
| } |
| inc_deq(xhci, xhci->cmd_ring, false); |
| } |
| |
| static void handle_port_status(struct xhci_hcd *xhci, |
| union xhci_trb *event) |
| { |
| u32 port_id; |
| |
| /* Port status change events always have a successful completion code */ |
| if (GET_COMP_CODE(event->generic.field[2]) != COMP_SUCCESS) { |
| xhci_warn(xhci, "WARN: xHC returned failed port status event\n"); |
| xhci->error_bitmask |= 1 << 8; |
| } |
| /* FIXME: core doesn't care about all port link state changes yet */ |
| port_id = GET_PORT_ID(event->generic.field[0]); |
| xhci_dbg(xhci, "Port Status Change Event for port %d\n", port_id); |
| |
| /* Update event ring dequeue pointer before dropping the lock */ |
| inc_deq(xhci, xhci->event_ring, true); |
| xhci_set_hc_event_deq(xhci); |
| |
| spin_unlock(&xhci->lock); |
| /* Pass this up to the core */ |
| usb_hcd_poll_rh_status(xhci_to_hcd(xhci)); |
| spin_lock(&xhci->lock); |
| } |
| |
| /* |
| * This TD is defined by the TRBs starting at start_trb in start_seg and ending |
| * at end_trb, which may be in another segment. If the suspect DMA address is a |
| * TRB in this TD, this function returns that TRB's segment. Otherwise it |
| * returns 0. |
| */ |
| static struct xhci_segment *trb_in_td( |
| struct xhci_segment *start_seg, |
| union xhci_trb *start_trb, |
| union xhci_trb *end_trb, |
| dma_addr_t suspect_dma) |
| { |
| dma_addr_t start_dma; |
| dma_addr_t end_seg_dma; |
| dma_addr_t end_trb_dma; |
| struct xhci_segment *cur_seg; |
| |
| start_dma = xhci_trb_virt_to_dma(start_seg, start_trb); |
| cur_seg = start_seg; |
| |
| do { |
| /* We may get an event for a Link TRB in the middle of a TD */ |
| end_seg_dma = xhci_trb_virt_to_dma(cur_seg, |
| &start_seg->trbs[TRBS_PER_SEGMENT - 1]); |
| /* If the end TRB isn't in this segment, this is set to 0 */ |
| end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb); |
| |
| if (end_trb_dma > 0) { |
| /* The end TRB is in this segment, so suspect should be here */ |
| if (start_dma <= end_trb_dma) { |
| if (suspect_dma >= start_dma && suspect_dma <= end_trb_dma) |
| return cur_seg; |
| } else { |
| /* Case for one segment with |
| * a TD wrapped around to the top |
| */ |
| if ((suspect_dma >= start_dma && |
| suspect_dma <= end_seg_dma) || |
| (suspect_dma >= cur_seg->dma && |
| suspect_dma <= end_trb_dma)) |
| return cur_seg; |
| } |
| return 0; |
| } else { |
| /* Might still be somewhere in this segment */ |
| if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma) |
| return cur_seg; |
| } |
| cur_seg = cur_seg->next; |
| start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]); |
| } while (1); |
| |
| } |
| |
| /* |
| * If this function returns an error condition, it means it got a Transfer |
| * event with a corrupted Slot ID, Endpoint ID, or TRB DMA address. |
| * At this point, the host controller is probably hosed and should be reset. |
| */ |
| static int handle_tx_event(struct xhci_hcd *xhci, |
| struct xhci_transfer_event *event) |
| { |
| struct xhci_virt_device *xdev; |
| struct xhci_ring *ep_ring; |
| int ep_index; |
| struct xhci_td *td = 0; |
| dma_addr_t event_dma; |
| struct xhci_segment *event_seg; |
| union xhci_trb *event_trb; |
| struct urb *urb = 0; |
| int status = -EINPROGRESS; |
| struct xhci_ep_ctx *ep_ctx; |
| |
| xhci_dbg(xhci, "In %s\n", __func__); |
| xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)]; |
| if (!xdev) { |
| xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n"); |
| return -ENODEV; |
| } |
| |
| /* Endpoint ID is 1 based, our index is zero based */ |
| ep_index = TRB_TO_EP_ID(event->flags) - 1; |
| xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); |
| ep_ring = xdev->ep_rings[ep_index]; |
| ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); |
| if (!ep_ring || (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { |
| xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n"); |
| return -ENODEV; |
| } |
| |
| event_dma = event->buffer; |
| /* This TRB should be in the TD at the head of this ring's TD list */ |
| xhci_dbg(xhci, "%s - checking for list empty\n", __func__); |
| if (list_empty(&ep_ring->td_list)) { |
| xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", |
| TRB_TO_SLOT_ID(event->flags), ep_index); |
| xhci_dbg(xhci, "Event TRB with TRB type ID %u\n", |
| (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10); |
| xhci_print_trb_offsets(xhci, (union xhci_trb *) event); |
| urb = NULL; |
| goto cleanup; |
| } |
| xhci_dbg(xhci, "%s - getting list entry\n", __func__); |
| td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list); |
| |
| /* Is this a TRB in the currently executing TD? */ |
| xhci_dbg(xhci, "%s - looking for TD\n", __func__); |
| event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue, |
| td->last_trb, event_dma); |
| xhci_dbg(xhci, "%s - found event_seg = %p\n", __func__, event_seg); |
| if (!event_seg) { |
| /* HC is busted, give up! */ |
| xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not part of current TD\n"); |
| return -ESHUTDOWN; |
| } |
| event_trb = &event_seg->trbs[(event_dma - event_seg->dma) / sizeof(*event_trb)]; |
| xhci_dbg(xhci, "Event TRB with TRB type ID %u\n", |
| (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10); |
| xhci_dbg(xhci, "Offset 0x00 (buffer lo) = 0x%x\n", |
| lower_32_bits(event->buffer)); |
| xhci_dbg(xhci, "Offset 0x04 (buffer hi) = 0x%x\n", |
| upper_32_bits(event->buffer)); |
| xhci_dbg(xhci, "Offset 0x08 (transfer length) = 0x%x\n", |
| (unsigned int) event->transfer_len); |
| xhci_dbg(xhci, "Offset 0x0C (flags) = 0x%x\n", |
| (unsigned int) event->flags); |
| |
| /* Look for common error cases */ |
| switch (GET_COMP_CODE(event->transfer_len)) { |
| /* Skip codes that require special handling depending on |
| * transfer type |
| */ |
| case COMP_SUCCESS: |
| case COMP_SHORT_TX: |
| break; |
| case COMP_STOP: |
| xhci_dbg(xhci, "Stopped on Transfer TRB\n"); |
| break; |
| case COMP_STOP_INVAL: |
| xhci_dbg(xhci, "Stopped on No-op or Link TRB\n"); |
| break; |
| case COMP_STALL: |
| xhci_warn(xhci, "WARN: Stalled endpoint\n"); |
| ep_ring->state |= EP_HALTED; |
| status = -EPIPE; |
| break; |
| case COMP_TRB_ERR: |
| xhci_warn(xhci, "WARN: TRB error on endpoint\n"); |
| status = -EILSEQ; |
| break; |
| case COMP_TX_ERR: |
| xhci_warn(xhci, "WARN: transfer error on endpoint\n"); |
| status = -EPROTO; |
| break; |
| case COMP_BABBLE: |
| xhci_warn(xhci, "WARN: babble error on endpoint\n"); |
| status = -EOVERFLOW; |
| break; |
| case COMP_DB_ERR: |
| xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n"); |
| status = -ENOSR; |
| break; |
| default: |
| xhci_warn(xhci, "ERROR Unknown event condition, HC probably busted\n"); |
| urb = NULL; |
| goto cleanup; |
| } |
| /* Now update the urb's actual_length and give back to the core */ |
| /* Was this a control transfer? */ |
| if (usb_endpoint_xfer_control(&td->urb->ep->desc)) { |
| xhci_debug_trb(xhci, xhci->event_ring->dequeue); |
| switch (GET_COMP_CODE(event->transfer_len)) { |
| case COMP_SUCCESS: |
| if (event_trb == ep_ring->dequeue) { |
| xhci_warn(xhci, "WARN: Success on ctrl setup TRB without IOC set??\n"); |
| status = -ESHUTDOWN; |
| } else if (event_trb != td->last_trb) { |
| xhci_warn(xhci, "WARN: Success on ctrl data TRB without IOC set??\n"); |
| status = -ESHUTDOWN; |
| } else { |
| xhci_dbg(xhci, "Successful control transfer!\n"); |
| status = 0; |
| } |
| break; |
| case COMP_SHORT_TX: |
| xhci_warn(xhci, "WARN: short transfer on control ep\n"); |
| status = -EREMOTEIO; |
| break; |
| default: |
| /* Others already handled above */ |
| break; |
| } |
| /* |
| * Did we transfer any data, despite the errors that might have |
| * happened? I.e. did we get past the setup stage? |
| */ |
| if (event_trb != ep_ring->dequeue) { |
| /* The event was for the status stage */ |
| if (event_trb == td->last_trb) { |
| /* Did we already see a short data stage? */ |
| if (td->urb->actual_length != 0) |
| status = -EREMOTEIO; |
| else |
| td->urb->actual_length = |
| td->urb->transfer_buffer_length; |
| } else { |
| /* Maybe the event was for the data stage? */ |
| if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) { |
| /* We didn't stop on a link TRB in the middle */ |
| td->urb->actual_length = |
| td->urb->transfer_buffer_length - |
| TRB_LEN(event->transfer_len); |
| xhci_dbg(xhci, "Waiting for status stage event\n"); |
| urb = NULL; |
| goto cleanup; |
| } |
| } |
| } |
| } else { |
| switch (GET_COMP_CODE(event->transfer_len)) { |
| case COMP_SUCCESS: |
| /* Double check that the HW transferred everything. */ |
| if (event_trb != td->last_trb) { |
| xhci_warn(xhci, "WARN Successful completion " |
| "on short TX\n"); |
| if (td->urb->transfer_flags & URB_SHORT_NOT_OK) |
| status = -EREMOTEIO; |
| else |
| status = 0; |
| } else { |
| xhci_dbg(xhci, "Successful bulk transfer!\n"); |
| status = 0; |
| } |
| break; |
| case COMP_SHORT_TX: |
| if (td->urb->transfer_flags & URB_SHORT_NOT_OK) |
| status = -EREMOTEIO; |
| else |
| status = 0; |
| break; |
| default: |
| /* Others already handled above */ |
| break; |
| } |
| dev_dbg(&td->urb->dev->dev, |
| "ep %#x - asked for %d bytes, " |
| "%d bytes untransferred\n", |
| td->urb->ep->desc.bEndpointAddress, |
| td->urb->transfer_buffer_length, |
| TRB_LEN(event->transfer_len)); |
| /* Fast path - was this the last TRB in the TD for this URB? */ |
| if (event_trb == td->last_trb) { |
| if (TRB_LEN(event->transfer_len) != 0) { |
| td->urb->actual_length = |
| td->urb->transfer_buffer_length - |
| TRB_LEN(event->transfer_len); |
| if (td->urb->actual_length < 0) { |
| xhci_warn(xhci, "HC gave bad length " |
| "of %d bytes left\n", |
| TRB_LEN(event->transfer_len)); |
| td->urb->actual_length = 0; |
| } |
| if (td->urb->transfer_flags & URB_SHORT_NOT_OK) |
| status = -EREMOTEIO; |
| else |
| status = 0; |
| } else { |
| td->urb->actual_length = td->urb->transfer_buffer_length; |
| /* Ignore a short packet completion if the |
| * untransferred length was zero. |
| */ |
| status = 0; |
| } |
| } else { |
| /* Slow path - walk the list, starting from the dequeue |
| * pointer, to get the actual length transferred. |
| */ |
| union xhci_trb *cur_trb; |
| struct xhci_segment *cur_seg; |
| |
| td->urb->actual_length = 0; |
| for (cur_trb = ep_ring->dequeue, cur_seg = ep_ring->deq_seg; |
| cur_trb != event_trb; |
| next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) { |
| if (TRB_TYPE(cur_trb->generic.field[3]) != TRB_TR_NOOP && |
| TRB_TYPE(cur_trb->generic.field[3]) != TRB_LINK) |
| td->urb->actual_length += |
| TRB_LEN(cur_trb->generic.field[2]); |
| } |
| /* If the ring didn't stop on a Link or No-op TRB, add |
| * in the actual bytes transferred from the Normal TRB |
| */ |
| if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) |
| td->urb->actual_length += |
| TRB_LEN(cur_trb->generic.field[2]) - |
| TRB_LEN(event->transfer_len); |
| } |
| } |
| /* The Endpoint Stop Command completion will take care of |
| * any stopped TDs. A stopped TD may be restarted, so don't update the |
| * ring dequeue pointer or take this TD off any lists yet. |
| */ |
| if (GET_COMP_CODE(event->transfer_len) == COMP_STOP_INVAL || |
| GET_COMP_CODE(event->transfer_len) == COMP_STOP) { |
| ep_ring->stopped_td = td; |
| ep_ring->stopped_trb = event_trb; |
| } else { |
| /* Update ring dequeue pointer */ |
| while (ep_ring->dequeue != td->last_trb) |
| inc_deq(xhci, ep_ring, false); |
| inc_deq(xhci, ep_ring, false); |
| |
| /* Clean up the endpoint's TD list */ |
| urb = td->urb; |
| list_del(&td->td_list); |
| /* Was this TD slated to be cancelled but completed anyway? */ |
| if (!list_empty(&td->cancelled_td_list)) { |
| list_del(&td->cancelled_td_list); |
| ep_ring->cancels_pending--; |
| } |
| kfree(td); |
| urb->hcpriv = NULL; |
| } |
| cleanup: |
| inc_deq(xhci, xhci->event_ring, true); |
| xhci_set_hc_event_deq(xhci); |
| |
| /* FIXME for multi-TD URBs (who have buffers bigger than 64MB) */ |
| if (urb) { |
| usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb); |
| xhci_dbg(xhci, "Giveback URB %p, len = %d, status = %d\n", |
| urb, td->urb->actual_length, status); |
| spin_unlock(&xhci->lock); |
| usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status); |
| spin_lock(&xhci->lock); |
| } |
| return 0; |
| } |
| |
| /* |
| * This function handles all OS-owned events on the event ring. It may drop |
| * xhci->lock between event processing (e.g. to pass up port status changes). |
| */ |
| void xhci_handle_event(struct xhci_hcd *xhci) |
| { |
| union xhci_trb *event; |
| int update_ptrs = 1; |
| int ret; |
| |
| xhci_dbg(xhci, "In %s\n", __func__); |
| if (!xhci->event_ring || !xhci->event_ring->dequeue) { |
| xhci->error_bitmask |= 1 << 1; |
| return; |
| } |
| |
| event = xhci->event_ring->dequeue; |
| /* Does the HC or OS own the TRB? */ |
| if ((event->event_cmd.flags & TRB_CYCLE) != |
| xhci->event_ring->cycle_state) { |
| xhci->error_bitmask |= 1 << 2; |
| return; |
| } |
| xhci_dbg(xhci, "%s - OS owns TRB\n", __func__); |
| |
| /* FIXME: Handle more event types. */ |
| switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) { |
| case TRB_TYPE(TRB_COMPLETION): |
| xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__); |
| handle_cmd_completion(xhci, &event->event_cmd); |
| xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__); |
| break; |
| case TRB_TYPE(TRB_PORT_STATUS): |
| xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__); |
| handle_port_status(xhci, event); |
| xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__); |
| update_ptrs = 0; |
| break; |
| case TRB_TYPE(TRB_TRANSFER): |
| xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__); |
| ret = handle_tx_event(xhci, &event->trans_event); |
| xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__); |
| if (ret < 0) |
| xhci->error_bitmask |= 1 << 9; |
| else |
| update_ptrs = 0; |
| break; |
| default: |
| xhci->error_bitmask |= 1 << 3; |
| } |
| |
| if (update_ptrs) { |
| /* Update SW and HC event ring dequeue pointer */ |
| inc_deq(xhci, xhci->event_ring, true); |
| xhci_set_hc_event_deq(xhci); |
| } |
| /* Are there more items on the event ring? */ |
| xhci_handle_event(xhci); |
| } |
| |
| /**** Endpoint Ring Operations ****/ |
| |
| /* |
| * Generic function for queueing a TRB on a ring. |
| * The caller must have checked to make sure there's room on the ring. |
| */ |
| static void queue_trb(struct xhci_hcd *xhci, struct xhci_ring *ring, |
| bool consumer, |
| u32 field1, u32 field2, u32 field3, u32 field4) |
| { |
| struct xhci_generic_trb *trb; |
| |
| trb = &ring->enqueue->generic; |
| trb->field[0] = field1; |
| trb->field[1] = field2; |
| trb->field[2] = field3; |
| trb->field[3] = field4; |
| inc_enq(xhci, ring, consumer); |
| } |
| |
| /* |
| * Does various checks on the endpoint ring, and makes it ready to queue num_trbs. |
| * FIXME allocate segments if the ring is full. |
| */ |
| static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, |
| u32 ep_state, unsigned int num_trbs, gfp_t mem_flags) |
| { |
| /* Make sure the endpoint has been added to xHC schedule */ |
| xhci_dbg(xhci, "Endpoint state = 0x%x\n", ep_state); |
| switch (ep_state) { |
| case EP_STATE_DISABLED: |
| /* |
| * USB core changed config/interfaces without notifying us, |
| * or hardware is reporting the wrong state. |
| */ |
| xhci_warn(xhci, "WARN urb submitted to disabled ep\n"); |
| return -ENOENT; |
| case EP_STATE_HALTED: |
| case EP_STATE_ERROR: |
| xhci_warn(xhci, "WARN waiting for halt or error on ep " |
| "to be cleared\n"); |
| /* FIXME event handling code for error needs to clear it */ |
| /* XXX not sure if this should be -ENOENT or not */ |
| return -EINVAL; |
| case EP_STATE_STOPPED: |
| case EP_STATE_RUNNING: |
| break; |
| default: |
| xhci_err(xhci, "ERROR unknown endpoint state for ep\n"); |
| /* |
| * FIXME issue Configure Endpoint command to try to get the HC |
| * back into a known state. |
| */ |
| return -EINVAL; |
| } |
| if (!room_on_ring(xhci, ep_ring, num_trbs)) { |
| /* FIXME allocate more room */ |
| xhci_err(xhci, "ERROR no room on ep ring\n"); |
| return -ENOMEM; |
| } |
| return 0; |
| } |
| |
| static int prepare_transfer(struct xhci_hcd *xhci, |
| struct xhci_virt_device *xdev, |
| unsigned int ep_index, |
| unsigned int num_trbs, |
| struct urb *urb, |
| struct xhci_td **td, |
| gfp_t mem_flags) |
| { |
| int ret; |
| struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); |
| ret = prepare_ring(xhci, xdev->ep_rings[ep_index], |
| ep_ctx->ep_info & EP_STATE_MASK, |
| num_trbs, mem_flags); |
| if (ret) |
| return ret; |
| *td = kzalloc(sizeof(struct xhci_td), mem_flags); |
| if (!*td) |
| return -ENOMEM; |
| INIT_LIST_HEAD(&(*td)->td_list); |
| INIT_LIST_HEAD(&(*td)->cancelled_td_list); |
| |
| ret = usb_hcd_link_urb_to_ep(xhci_to_hcd(xhci), urb); |
| if (unlikely(ret)) { |
| kfree(*td); |
| return ret; |
| } |
| |
| (*td)->urb = urb; |
| urb->hcpriv = (void *) (*td); |
| /* Add this TD to the tail of the endpoint ring's TD list */ |
| list_add_tail(&(*td)->td_list, &xdev->ep_rings[ep_index]->td_list); |
| (*td)->start_seg = xdev->ep_rings[ep_index]->enq_seg; |
| (*td)->first_trb = xdev->ep_rings[ep_index]->enqueue; |
| |
| return 0; |
| } |
| |
| static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb) |
| { |
| int num_sgs, num_trbs, running_total, temp, i; |
| struct scatterlist *sg; |
| |
| sg = NULL; |
| num_sgs = urb->num_sgs; |
| temp = urb->transfer_buffer_length; |
| |
| xhci_dbg(xhci, "count sg list trbs: \n"); |
| num_trbs = 0; |
| for_each_sg(urb->sg->sg, sg, num_sgs, i) { |
| unsigned int previous_total_trbs = num_trbs; |
| unsigned int len = sg_dma_len(sg); |
| |
| /* Scatter gather list entries may cross 64KB boundaries */ |
| running_total = TRB_MAX_BUFF_SIZE - |
| (sg_dma_address(sg) & ((1 << TRB_MAX_BUFF_SHIFT) - 1)); |
| if (running_total != 0) |
| num_trbs++; |
| |
| /* How many more 64KB chunks to transfer, how many more TRBs? */ |
| while (running_total < sg_dma_len(sg)) { |
| num_trbs++; |
| running_total += TRB_MAX_BUFF_SIZE; |
| } |
| xhci_dbg(xhci, " sg #%d: dma = %#llx, len = %#x (%d), num_trbs = %d\n", |
| i, (unsigned long long)sg_dma_address(sg), |
| len, len, num_trbs - previous_total_trbs); |
| |
| len = min_t(int, len, temp); |
| temp -= len; |
| if (temp == 0) |
| break; |
| } |
| xhci_dbg(xhci, "\n"); |
| if (!in_interrupt()) |
| dev_dbg(&urb->dev->dev, "ep %#x - urb len = %d, sglist used, num_trbs = %d\n", |
| urb->ep->desc.bEndpointAddress, |
| urb->transfer_buffer_length, |
| num_trbs); |
| return num_trbs; |
| } |
| |
| static void check_trb_math(struct urb *urb, int num_trbs, int running_total) |
| { |
| if (num_trbs != 0) |
| dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated number of " |
| "TRBs, %d left\n", __func__, |
| urb->ep->desc.bEndpointAddress, num_trbs); |
| if (running_total != urb->transfer_buffer_length) |
| dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated tx length, " |
| "queued %#x (%d), asked for %#x (%d)\n", |
| __func__, |
| urb->ep->desc.bEndpointAddress, |
| running_total, running_total, |
| urb->transfer_buffer_length, |
| urb->transfer_buffer_length); |
| } |
| |
| static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, |
| unsigned int ep_index, int start_cycle, |
| struct xhci_generic_trb *start_trb, struct xhci_td *td) |
| { |
| /* |
| * Pass all the TRBs to the hardware at once and make sure this write |
| * isn't reordered. |
| */ |
| wmb(); |
| start_trb->field[3] |= start_cycle; |
| ring_ep_doorbell(xhci, slot_id, ep_index); |
| } |
| |
| static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, |
| struct urb *urb, int slot_id, unsigned int ep_index) |
| { |
| struct xhci_ring *ep_ring; |
| unsigned int num_trbs; |
| struct xhci_td *td; |
| struct scatterlist *sg; |
| int num_sgs; |
| int trb_buff_len, this_sg_len, running_total; |
| bool first_trb; |
| u64 addr; |
| |
| struct xhci_generic_trb *start_trb; |
| int start_cycle; |
| |
| ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; |
| num_trbs = count_sg_trbs_needed(xhci, urb); |
| num_sgs = urb->num_sgs; |
| |
| trb_buff_len = prepare_transfer(xhci, xhci->devs[slot_id], |
| ep_index, num_trbs, urb, &td, mem_flags); |
| if (trb_buff_len < 0) |
| return trb_buff_len; |
| /* |
| * Don't give the first TRB to the hardware (by toggling the cycle bit) |
| * until we've finished creating all the other TRBs. The ring's cycle |
| * state may change as we enqueue the other TRBs, so save it too. |
| */ |
| start_trb = &ep_ring->enqueue->generic; |
| start_cycle = ep_ring->cycle_state; |
| |
| running_total = 0; |
| /* |
| * How much data is in the first TRB? |
| * |
| * There are three forces at work for TRB buffer pointers and lengths: |
| * 1. We don't want to walk off the end of this sg-list entry buffer. |
| * 2. The transfer length that the driver requested may be smaller than |
| * the amount of memory allocated for this scatter-gather list. |
| * 3. TRBs buffers can't cross 64KB boundaries. |
| */ |
| sg = urb->sg->sg; |
| addr = (u64) sg_dma_address(sg); |
| this_sg_len = sg_dma_len(sg); |
| trb_buff_len = TRB_MAX_BUFF_SIZE - |
| (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1)); |
| trb_buff_len = min_t(int, trb_buff_len, this_sg_len); |
| if (trb_buff_len > urb->transfer_buffer_length) |
| trb_buff_len = urb->transfer_buffer_length; |
| xhci_dbg(xhci, "First length to xfer from 1st sglist entry = %u\n", |
| trb_buff_len); |
| |
| first_trb = true; |
| /* Queue the first TRB, even if it's zero-length */ |
| do { |
| u32 field = 0; |
| u32 length_field = 0; |
| |
| /* Don't change the cycle bit of the first TRB until later */ |
| if (first_trb) |
| first_trb = false; |
| else |
| field |= ep_ring->cycle_state; |
| |
| /* Chain all the TRBs together; clear the chain bit in the last |
| * TRB to indicate it's the last TRB in the chain. |
| */ |
| if (num_trbs > 1) { |
| field |= TRB_CHAIN; |
| } else { |
| /* FIXME - add check for ZERO_PACKET flag before this */ |
| td->last_trb = ep_ring->enqueue; |
| field |= TRB_IOC; |
| } |
| xhci_dbg(xhci, " sg entry: dma = %#x, len = %#x (%d), " |
| "64KB boundary at %#x, end dma = %#x\n", |
| (unsigned int) addr, trb_buff_len, trb_buff_len, |
| (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1), |
| (unsigned int) addr + trb_buff_len); |
| if (TRB_MAX_BUFF_SIZE - |
| (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1)) < trb_buff_len) { |
| xhci_warn(xhci, "WARN: sg dma xfer crosses 64KB boundaries!\n"); |
| xhci_dbg(xhci, "Next boundary at %#x, end dma = %#x\n", |
| (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1), |
| (unsigned int) addr + trb_buff_len); |
| } |
| length_field = TRB_LEN(trb_buff_len) | |
| TD_REMAINDER(urb->transfer_buffer_length - running_total) | |
| TRB_INTR_TARGET(0); |
| queue_trb(xhci, ep_ring, false, |
| lower_32_bits(addr), |
| upper_32_bits(addr), |
| length_field, |
| /* We always want to know if the TRB was short, |
| * or we won't get an event when it completes. |
| * (Unless we use event data TRBs, which are a |
| * waste of space and HC resources.) |
| */ |
| field | TRB_ISP | TRB_TYPE(TRB_NORMAL)); |
| --num_trbs; |
| running_total += trb_buff_len; |
| |
| /* Calculate length for next transfer -- |
| * Are we done queueing all the TRBs for this sg entry? |
| */ |
| this_sg_len -= trb_buff_len; |
| if (this_sg_len == 0) { |
| --num_sgs; |
| if (num_sgs == 0) |
| break; |
| sg = sg_next(sg); |
| addr = (u64) sg_dma_address(sg); |
| this_sg_len = sg_dma_len(sg); |
| } else { |
| addr += trb_buff_len; |
| } |
| |
| trb_buff_len = TRB_MAX_BUFF_SIZE - |
| (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1)); |
| trb_buff_len = min_t(int, trb_buff_len, this_sg_len); |
| if (running_total + trb_buff_len > urb->transfer_buffer_length) |
| trb_buff_len = |
| urb->transfer_buffer_length - running_total; |
| } while (running_total < urb->transfer_buffer_length); |
| |
| check_trb_math(urb, num_trbs, running_total); |
| giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td); |
| return 0; |
| } |
| |
| /* This is very similar to what ehci-q.c qtd_fill() does */ |
| int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, |
| struct urb *urb, int slot_id, unsigned int ep_index) |
| { |
| struct xhci_ring *ep_ring; |
| struct xhci_td *td; |
| int num_trbs; |
| struct xhci_generic_trb *start_trb; |
| bool first_trb; |
| int start_cycle; |
| u32 field, length_field; |
| |
| int running_total, trb_buff_len, ret; |
| u64 addr; |
| |
| if (urb->sg) |
| return queue_bulk_sg_tx(xhci, mem_flags, urb, slot_id, ep_index); |
| |
| ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; |
| |
| num_trbs = 0; |
| /* How much data is (potentially) left before the 64KB boundary? */ |
| running_total = TRB_MAX_BUFF_SIZE - |
| (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1)); |
| |
| /* If there's some data on this 64KB chunk, or we have to send a |
| * zero-length transfer, we need at least one TRB |
| */ |
| if (running_total != 0 || urb->transfer_buffer_length == 0) |
| num_trbs++; |
| /* How many more 64KB chunks to transfer, how many more TRBs? */ |
| while (running_total < urb->transfer_buffer_length) { |
| num_trbs++; |
| running_total += TRB_MAX_BUFF_SIZE; |
| } |
| /* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */ |
| |
| if (!in_interrupt()) |
| dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d), addr = %#llx, num_trbs = %d\n", |
| urb->ep->desc.bEndpointAddress, |
| urb->transfer_buffer_length, |
| urb->transfer_buffer_length, |
| (unsigned long long)urb->transfer_dma, |
| num_trbs); |
| |
| ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index, |
| num_trbs, urb, &td, mem_flags); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Don't give the first TRB to the hardware (by toggling the cycle bit) |
| * until we've finished creating all the other TRBs. The ring's cycle |
| * state may change as we enqueue the other TRBs, so save it too. |
| */ |
| start_trb = &ep_ring->enqueue->generic; |
| start_cycle = ep_ring->cycle_state; |
| |
| running_total = 0; |
| /* How much data is in the first TRB? */ |
| addr = (u64) urb->transfer_dma; |
| trb_buff_len = TRB_MAX_BUFF_SIZE - |
| (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1)); |
| if (urb->transfer_buffer_length < trb_buff_len) |
| trb_buff_len = urb->transfer_buffer_length; |
| |
| first_trb = true; |
| |
| /* Queue the first TRB, even if it's zero-length */ |
| do { |
| field = 0; |
| |
| /* Don't change the cycle bit of the first TRB until later */ |
| if (first_trb) |
| first_trb = false; |
| else |
| field |= ep_ring->cycle_state; |
| |
| /* Chain all the TRBs together; clear the chain bit in the last |
| * TRB to indicate it's the last TRB in the chain. |
| */ |
| if (num_trbs > 1) { |
| field |= TRB_CHAIN; |
| } else { |
| /* FIXME - add check for ZERO_PACKET flag before this */ |
| td->last_trb = ep_ring->enqueue; |
| field |= TRB_IOC; |
| } |
| length_field = TRB_LEN(trb_buff_len) | |
| TD_REMAINDER(urb->transfer_buffer_length - running_total) | |
| TRB_INTR_TARGET(0); |
| queue_trb(xhci, ep_ring, false, |
| lower_32_bits(addr), |
| upper_32_bits(addr), |
| length_field, |
| /* We always want to know if the TRB was short, |
| * or we won't get an event when it completes. |
| * (Unless we use event data TRBs, which are a |
| * waste of space and HC resources.) |
| */ |
| field | TRB_ISP | TRB_TYPE(TRB_NORMAL)); |
| --num_trbs; |
| running_total += trb_buff_len; |
| |
| /* Calculate length for next transfer */ |
| addr += trb_buff_len; |
| trb_buff_len = urb->transfer_buffer_length - running_total; |
| if (trb_buff_len > TRB_MAX_BUFF_SIZE) |
| trb_buff_len = TRB_MAX_BUFF_SIZE; |
| } while (running_total < urb->transfer_buffer_length); |
| |
| check_trb_math(urb, num_trbs, running_total); |
| giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td); |
| return 0; |
| } |
| |
| /* Caller must have locked xhci->lock */ |
| int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, |
| struct urb *urb, int slot_id, unsigned int ep_index) |
| { |
| struct xhci_ring *ep_ring; |
| int num_trbs; |
| int ret; |
| struct usb_ctrlrequest *setup; |
| struct xhci_generic_trb *start_trb; |
| int start_cycle; |
| u32 field, length_field; |
| struct xhci_td *td; |
| |
| ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; |
| |
| /* |
| * Need to copy setup packet into setup TRB, so we can't use the setup |
| * DMA address. |
| */ |
| if (!urb->setup_packet) |
| return -EINVAL; |
| |
| if (!in_interrupt()) |
| xhci_dbg(xhci, "Queueing ctrl tx for slot id %d, ep %d\n", |
| slot_id, ep_index); |
| /* 1 TRB for setup, 1 for status */ |
| num_trbs = 2; |
| /* |
| * Don't need to check if we need additional event data and normal TRBs, |
| * since data in control transfers will never get bigger than 16MB |
| * XXX: can we get a buffer that crosses 64KB boundaries? |
| */ |
| if (urb->transfer_buffer_length > 0) |
| num_trbs++; |
| ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index, num_trbs, |
| urb, &td, mem_flags); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Don't give the first TRB to the hardware (by toggling the cycle bit) |
| * until we've finished creating all the other TRBs. The ring's cycle |
| * state may change as we enqueue the other TRBs, so save it too. |
| */ |
| start_trb = &ep_ring->enqueue->generic; |
| start_cycle = ep_ring->cycle_state; |
| |
| /* Queue setup TRB - see section 6.4.1.2.1 */ |
| /* FIXME better way to translate setup_packet into two u32 fields? */ |
| setup = (struct usb_ctrlrequest *) urb->setup_packet; |
| queue_trb(xhci, ep_ring, false, |
| /* FIXME endianness is probably going to bite my ass here. */ |
| setup->bRequestType | setup->bRequest << 8 | setup->wValue << 16, |
| setup->wIndex | setup->wLength << 16, |
| TRB_LEN(8) | TRB_INTR_TARGET(0), |
| /* Immediate data in pointer */ |
| TRB_IDT | TRB_TYPE(TRB_SETUP)); |
| |
| /* If there's data, queue data TRBs */ |
| field = 0; |
| length_field = TRB_LEN(urb->transfer_buffer_length) | |
| TD_REMAINDER(urb->transfer_buffer_length) | |
| TRB_INTR_TARGET(0); |
| if (urb->transfer_buffer_length > 0) { |
| if (setup->bRequestType & USB_DIR_IN) |
| field |= TRB_DIR_IN; |
| queue_trb(xhci, ep_ring, false, |
| lower_32_bits(urb->transfer_dma), |
| upper_32_bits(urb->transfer_dma), |
| length_field, |
| /* Event on short tx */ |
| field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state); |
| } |
| |
| /* Save the DMA address of the last TRB in the TD */ |
| td->last_trb = ep_ring->enqueue; |
| |
| /* Queue status TRB - see Table 7 and sections 4.11.2.2 and 6.4.1.2.3 */ |
| /* If the device sent data, the status stage is an OUT transfer */ |
| if (urb->transfer_buffer_length > 0 && setup->bRequestType & USB_DIR_IN) |
| field = 0; |
| else |
| field = TRB_DIR_IN; |
| queue_trb(xhci, ep_ring, false, |
| 0, |
| 0, |
| TRB_INTR_TARGET(0), |
| /* Event on completion */ |
| field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state); |
| |
| giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td); |
| return 0; |
| } |
| |
| /**** Command Ring Operations ****/ |
| |
| /* Generic function for queueing a command TRB on the command ring */ |
| static int queue_command(struct xhci_hcd *xhci, u32 field1, u32 field2, u32 field3, u32 field4) |
| { |
| if (!room_on_ring(xhci, xhci->cmd_ring, 1)) { |
| if (!in_interrupt()) |
| xhci_err(xhci, "ERR: No room for command on command ring\n"); |
| return -ENOMEM; |
| } |
| queue_trb(xhci, xhci->cmd_ring, false, field1, field2, field3, |
| field4 | xhci->cmd_ring->cycle_state); |
| return 0; |
| } |
| |
| /* Queue a no-op command on the command ring */ |
| static int queue_cmd_noop(struct xhci_hcd *xhci) |
| { |
| return queue_command(xhci, 0, 0, 0, TRB_TYPE(TRB_CMD_NOOP)); |
| } |
| |
| /* |
| * Place a no-op command on the command ring to test the command and |
| * event ring. |
| */ |
| void *xhci_setup_one_noop(struct xhci_hcd *xhci) |
| { |
| if (queue_cmd_noop(xhci) < 0) |
| return NULL; |
| xhci->noops_submitted++; |
| return xhci_ring_cmd_db; |
| } |
| |
| /* Queue a slot enable or disable request on the command ring */ |
| int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id) |
| { |
| return queue_command(xhci, 0, 0, 0, |
| TRB_TYPE(trb_type) | SLOT_ID_FOR_TRB(slot_id)); |
| } |
| |
| /* Queue an address device command TRB */ |
| int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, |
| u32 slot_id) |
| { |
| return queue_command(xhci, lower_32_bits(in_ctx_ptr), |
| upper_32_bits(in_ctx_ptr), 0, |
| TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id)); |
| } |
| |
| /* Queue a configure endpoint command TRB */ |
| int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, |
| u32 slot_id) |
| { |
| return queue_command(xhci, lower_32_bits(in_ctx_ptr), |
| upper_32_bits(in_ctx_ptr), 0, |
| TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id)); |
| } |
| |
| int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, int slot_id, |
| unsigned int ep_index) |
| { |
| u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); |
| u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); |
| u32 type = TRB_TYPE(TRB_STOP_RING); |
| |
| return queue_command(xhci, 0, 0, 0, |
| trb_slot_id | trb_ep_index | type); |
| } |
| |
| /* Set Transfer Ring Dequeue Pointer command. |
| * This should not be used for endpoints that have streams enabled. |
| */ |
| static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, |
| unsigned int ep_index, struct xhci_segment *deq_seg, |
| union xhci_trb *deq_ptr, u32 cycle_state) |
| { |
| dma_addr_t addr; |
| u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); |
| u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); |
| u32 type = TRB_TYPE(TRB_SET_DEQ); |
| |
| addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr); |
| if (addr == 0) |
| xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n"); |
| xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n", |
| deq_seg, deq_ptr); |
| return queue_command(xhci, lower_32_bits(addr) | cycle_state, |
| upper_32_bits(addr), 0, |
| trb_slot_id | trb_ep_index | type); |
| } |
| |
| int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, |
| unsigned int ep_index) |
| { |
| u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); |
| u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); |
| u32 type = TRB_TYPE(TRB_RESET_EP); |
| |
| return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type); |
| } |