Google Git
Sign in
googlers / maze / linux / be1bc2889a4db4961ef69f47fb471ecae9f23ade / . / drivers / serial / 68360serial.c
blob: 16f5f2fab0323fcc2c75ac5a2da55079632745e2 [file] [log] [blame]
/*
* UART driver for 68360 CPM SCC or SMC
* Copyright (c) 2000 D. Jeff Dionne <jeff@uclinux.org>,
* Copyright (c) 2000 Michael Leslie <mleslie@lineo.ca>
* Copyright (c) 1997 Dan Malek <dmalek@jlc.net>
*
* I used the serial.c driver as the framework for this driver.
* Give credit to those guys.
* The original code was written for the MBX860 board. I tried to make
* it generic, but there may be some assumptions in the structures that
* have to be fixed later.
* To save porting time, I did not bother to change any object names
* that are not accessed outside of this file.
* It still needs lots of work........When it was easy, I included code
* to support the SCCs, but this has never been tested, nor is it complete.
* Only the SCCs support modem control, so that is not complete either.
*
* This module exports the following rs232 io functions:
*
* int rs_360_init(void);
*/
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial.h>
#include <linux/serialP.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/fcntl.h>
#include <linux/ptrace.h>
#include <linux/mm.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <asm/irq.h>
#include <asm/m68360.h>
#include <asm/commproc.h>
#ifdef CONFIG_KGDB
extern void breakpoint(void);
extern void set_debug_traps(void);
extern int kgdb_output_string (const char* s, unsigned int count);
#endif
/* #ifdef CONFIG_SERIAL_CONSOLE */ /* This seems to be a post 2.0 thing - mles */
#include <linux/console.h>
#include <linux/jiffies.h>
/* this defines the index into rs_table for the port to use
*/
#ifndef CONFIG_SERIAL_CONSOLE_PORT
#define CONFIG_SERIAL_CONSOLE_PORT 1 /* ie SMC2 - note USE_SMC2 must be defined */
#endif
/* #endif */
#if 0
/* SCC2 for console
*/
#undef CONFIG_SERIAL_CONSOLE_PORT
#define CONFIG_SERIAL_CONSOLE_PORT 2
#endif
#define TX_WAKEUP ASYNC_SHARE_IRQ
static char *serial_name = "CPM UART driver";
static char *serial_version = "0.03";
static struct tty_driver *serial_driver;
int serial_console_setup(struct console *co, char *options);
/*
* Serial driver configuration section. Here are the various options:
*/
#define SERIAL_PARANOIA_CHECK
#define CONFIG_SERIAL_NOPAUSE_IO
#define SERIAL_DO_RESTART
/* Set of debugging defines */
#undef SERIAL_DEBUG_INTR
#undef SERIAL_DEBUG_OPEN
#undef SERIAL_DEBUG_FLOW
#undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
#define _INLINE_ inline
#define DBG_CNT(s)
/* We overload some of the items in the data structure to meet our
* needs. For example, the port address is the CPM parameter ram
* offset for the SCC or SMC. The maximum number of ports is 4 SCCs and
* 2 SMCs. The "hub6" field is used to indicate the channel number, with
* a flag indicating SCC or SMC, and the number is used as an index into
* the CPM parameter area for this device.
* The "type" field is currently set to 0, for PORT_UNKNOWN. It is
* not currently used. I should probably use it to indicate the port
* type of SMC or SCC.
* The SMCs do not support any modem control signals.
*/
#define smc_scc_num hub6
#define NUM_IS_SCC ((int)0x00010000)
#define PORT_NUM(P) ((P) & 0x0000ffff)
#if defined (CONFIG_UCQUICC)
volatile extern void *_periph_base;
/* sipex transceiver
* mode bits for are on pins
*
* SCC2 d16..19
* SCC3 d20..23
* SCC4 d24..27
*/
#define SIPEX_MODE(n,m) ((m & 0x0f)<<(16+4*(n-1)))
static uint sipex_mode_bits = 0x00000000;
#endif
/* There is no `serial_state' defined back here in 2.0.
* Try to get by with serial_struct
*/
/* #define serial_state serial_struct */
/* 2.4 -> 2.0 portability problem: async_icount in 2.4 has a few
* extras: */
#if 0
struct async_icount_24 {
__u32 cts, dsr, rng, dcd, tx, rx;
__u32 frame, parity, overrun, brk;
__u32 buf_overrun;
} icount;
#endif
#if 0
struct serial_state {
int magic;
int baud_base;
unsigned long port;
int irq;
int flags;
int hub6;
int type;
int line;
int revision; /* Chip revision (950) */
int xmit_fifo_size;
int custom_divisor;
int count;
u8 *iomem_base;
u16 iomem_reg_shift;
unsigned short close_delay;
unsigned short closing_wait; /* time to wait before closing */
struct async_icount_24 icount;
int io_type;
struct async_struct *info;
};
#endif
#define SSTATE_MAGIC 0x5302
/* SMC2 is sometimes used for low performance TDM interfaces. Define
* this as 1 if you want SMC2 as a serial port UART managed by this driver.
* Define this as 0 if you wish to use SMC2 for something else.
*/
#define USE_SMC2 1
#if 0
/* Define SCC to ttySx mapping. */
#define SCC_NUM_BASE (USE_SMC2 + 1) /* SCC base tty "number" */
/* Define which SCC is the first one to use for a serial port. These
* are 0-based numbers, i.e. this assumes the first SCC (SCC1) is used
* for Ethernet, and the first available SCC for serial UART is SCC2.
* NOTE: IF YOU CHANGE THIS, you have to change the PROFF_xxx and
* interrupt vectors in the table below to match.
*/
#define SCC_IDX_BASE 1 /* table index */
#endif
/* Processors other than the 860 only get SMCs configured by default.
* Either they don't have SCCs or they are allocated somewhere else.
* Of course, there are now 860s without some SCCs, so we will need to
* address that someday.
* The Embedded Planet Multimedia I/O cards use TDM interfaces to the
* stereo codec parts, and we use SMC2 to help support that.
*/
static struct serial_state rs_table[] = {
/* type line PORT IRQ FLAGS smc_scc_num (F.K.A. hub6) */
{ 0, 0, PRSLOT_SMC1, CPMVEC_SMC1, 0, 0 } /* SMC1 ttyS0 */
#if USE_SMC2
,{ 0, 0, PRSLOT_SMC2, CPMVEC_SMC2, 0, 1 } /* SMC2 ttyS1 */
#endif
#if defined(CONFIG_SERIAL_68360_SCC)
,{ 0, 0, PRSLOT_SCC2, CPMVEC_SCC2, 0, (NUM_IS_SCC | 1) } /* SCC2 ttyS2 */
,{ 0, 0, PRSLOT_SCC3, CPMVEC_SCC3, 0, (NUM_IS_SCC | 2) } /* SCC3 ttyS3 */
,{ 0, 0, PRSLOT_SCC4, CPMVEC_SCC4, 0, (NUM_IS_SCC | 3) } /* SCC4 ttyS4 */
#endif
};
#define NR_PORTS (sizeof(rs_table)/sizeof(struct serial_state))
/* The number of buffer descriptors and their sizes.
*/
#define RX_NUM_FIFO 4
#define RX_BUF_SIZE 32
#define TX_NUM_FIFO 4
#define TX_BUF_SIZE 32
#define CONSOLE_NUM_FIFO 2
#define CONSOLE_BUF_SIZE 4
char *console_fifos[CONSOLE_NUM_FIFO * CONSOLE_BUF_SIZE];
/* The async_struct in serial.h does not really give us what we
* need, so define our own here.
*/
typedef struct serial_info {
int magic;
int flags;
struct serial_state *state;
/* struct serial_struct *state; */
/* struct async_struct *state; */
struct tty_struct *tty;
int read_status_mask;
int ignore_status_mask;
int timeout;
int line;
int x_char; /* xon/xoff character */
int close_delay;
unsigned short closing_wait;
unsigned short closing_wait2;
unsigned long event;
unsigned long last_active;
int blocked_open; /* # of blocked opens */
struct work_struct tqueue;
struct work_struct tqueue_hangup;
wait_queue_head_t open_wait;
wait_queue_head_t close_wait;
/* CPM Buffer Descriptor pointers.
*/
QUICC_BD *rx_bd_base;
QUICC_BD *rx_cur;
QUICC_BD *tx_bd_base;
QUICC_BD *tx_cur;
} ser_info_t;
/* since kmalloc_init() does not get called until much after this initialization: */
static ser_info_t quicc_ser_info[NR_PORTS];
static char rx_buf_pool[NR_PORTS * RX_NUM_FIFO * RX_BUF_SIZE];
static char tx_buf_pool[NR_PORTS * TX_NUM_FIFO * TX_BUF_SIZE];
static void change_speed(ser_info_t *info);
static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout);
static inline int serial_paranoia_check(ser_info_t *info,
char *name, const char *routine)
{
#ifdef SERIAL_PARANOIA_CHECK
static const char *badmagic =
"Warning: bad magic number for serial struct (%s) in %s\n";
static const char *badinfo =
"Warning: null async_struct for (%s) in %s\n";
if (!info) {
printk(badinfo, name, routine);
return 1;
}
if (info->magic != SERIAL_MAGIC) {
printk(badmagic, name, routine);
return 1;
}
#endif
return 0;
}
/*
* This is used to figure out the divisor speeds and the timeouts,
* indexed by the termio value. The generic CPM functions are responsible
* for setting and assigning baud rate generators for us.
*/
static int baud_table[] = {
0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
9600, 19200, 38400, 57600, 115200, 230400, 460800, 0 };
/* This sucks. There is a better way: */
#if defined(CONFIG_CONSOLE_9600)
#define CONSOLE_BAUDRATE 9600
#elif defined(CONFIG_CONSOLE_19200)
#define CONSOLE_BAUDRATE 19200
#elif defined(CONFIG_CONSOLE_115200)
#define CONSOLE_BAUDRATE 115200
#else
#warning "console baud rate undefined"
#define CONSOLE_BAUDRATE 9600
#endif
/*
* ------------------------------------------------------------
* rs_stop() and rs_start()
*
* This routines are called before setting or resetting tty->stopped.
* They enable or disable transmitter interrupts, as necessary.
* ------------------------------------------------------------
*/
static void rs_360_stop(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
int idx;
unsigned long flags;
volatile struct scc_regs *sccp;
volatile struct smc_regs *smcp;
if (serial_paranoia_check(info, tty->name, "rs_stop"))
return;
local_irq_save(flags);
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
sccp->scc_sccm &= ~UART_SCCM_TX;
} else {
/* smcp = &cpmp->cp_smc[idx]; */
smcp = &pquicc->smc_regs[idx];
smcp->smc_smcm &= ~SMCM_TX;
}
local_irq_restore(flags);
}
static void rs_360_start(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
int idx;
unsigned long flags;
volatile struct scc_regs *sccp;
volatile struct smc_regs *smcp;
if (serial_paranoia_check(info, tty->name, "rs_stop"))
return;
local_irq_save(flags);
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
sccp->scc_sccm |= UART_SCCM_TX;
} else {
smcp = &pquicc->smc_regs[idx];
smcp->smc_smcm |= SMCM_TX;
}
local_irq_restore(flags);
}
/*
* ----------------------------------------------------------------------
*
* Here starts the interrupt handling routines. All of the following
* subroutines are declared as inline and are folded into
* rs_interrupt(). They were separated out for readability's sake.
*
* Note: rs_interrupt() is a "fast" interrupt, which means that it
* runs with interrupts turned off. People who may want to modify
* rs_interrupt() should try to keep the interrupt handler as fast as
* possible. After you are done making modifications, it is not a bad
* idea to do:
*
* gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
*
* and look at the resulting assemble code in serial.s.
*
* - Ted Ts'o (tytso@mit.edu), 7-Mar-93
* -----------------------------------------------------------------------
*/
static _INLINE_ void receive_chars(ser_info_t *info)
{
struct tty_struct *tty = info->port.tty;
unsigned char ch, flag, *cp;
/*int ignored = 0;*/
int i;
ushort status;
struct async_icount *icount;
/* struct async_icount_24 *icount; */
volatile QUICC_BD *bdp;
icount = &info->state->icount;
/* Just loop through the closed BDs and copy the characters into
* the buffer.
*/
bdp = info->rx_cur;
for (;;) {
if (bdp->status & BD_SC_EMPTY) /* If this one is empty */
break; /* we are all done */
/* The read status mask tell us what we should do with
* incoming characters, especially if errors occur.
* One special case is the use of BD_SC_EMPTY. If
* this is not set, we are supposed to be ignoring
* inputs. In this case, just mark the buffer empty and
* continue.
*/
if (!(info->read_status_mask & BD_SC_EMPTY)) {
bdp->status |= BD_SC_EMPTY;
bdp->status &=
~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV);
if (bdp->status & BD_SC_WRAP)
bdp = info->rx_bd_base;
else
bdp++;
continue;
}
/* Get the number of characters and the buffer pointer.
*/
i = bdp->length;
/* cp = (unsigned char *)__va(bdp->buf); */
cp = (char *)bdp->buf;
status = bdp->status;
while (i-- > 0) {
ch = *cp++;
icount->rx++;
#ifdef SERIAL_DEBUG_INTR
printk("DR%02x:%02x...", ch, status);
#endif
flag = TTY_NORMAL;
if (status & (BD_SC_BR | BD_SC_FR |
BD_SC_PR | BD_SC_OV)) {
/*
* For statistics only
*/
if (status & BD_SC_BR)
icount->brk++;
else if (status & BD_SC_PR)
icount->parity++;
else if (status & BD_SC_FR)
icount->frame++;
if (status & BD_SC_OV)
icount->overrun++;
/*
* Now check to see if character should be
* ignored, and mask off conditions which
* should be ignored.
if (status & info->ignore_status_mask) {
if (++ignored > 100)
break;
continue;
}
*/
status &= info->read_status_mask;
if (status & (BD_SC_BR)) {
#ifdef SERIAL_DEBUG_INTR
printk("handling break....");
#endif
*tty->flip.flag_buf_ptr = TTY_BREAK;
if (info->flags & ASYNC_SAK)
do_SAK(tty);
} else if (status & BD_SC_PR)
flag = TTY_PARITY;
else if (status & BD_SC_FR)
flag = TTY_FRAME;
}
tty_insert_flip_char(tty, ch, flag);
if (status & BD_SC_OV)
/*
* Overrun is special, since it's
* reported immediately, and doesn't
* affect the current character
*/
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
}
/* This BD is ready to be used again. Clear status.
* Get next BD.
*/
bdp->status |= BD_SC_EMPTY;
bdp->status &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV);
if (bdp->status & BD_SC_WRAP)
bdp = info->rx_bd_base;
else
bdp++;
}
info->rx_cur = (QUICC_BD *)bdp;
tty_schedule_flip(tty);
}
static _INLINE_ void receive_break(ser_info_t *info)
{
struct tty_struct *tty = info->port.tty;
info->state->icount.brk++;
/* Check to see if there is room in the tty buffer for
* the break. If not, we exit now, losing the break. FIXME
*/
tty_insert_flip_char(tty, 0, TTY_BREAK);
tty_schedule_flip(tty);
}
static _INLINE_ void transmit_chars(ser_info_t *info)
{
if ((info->flags & TX_WAKEUP) ||
(info->port.tty->flags & (1 << TTY_DO_WRITE_WAKEUP))) {
schedule_work(&info->tqueue);
}
#ifdef SERIAL_DEBUG_INTR
printk("THRE...");
#endif
}
#ifdef notdef
/* I need to do this for the SCCs, so it is left as a reminder.
*/
static _INLINE_ void check_modem_status(struct async_struct *info)
{
int status;
/* struct async_icount *icount; */
struct async_icount_24 *icount;
status = serial_in(info, UART_MSR);
if (status & UART_MSR_ANY_DELTA) {
icount = &info->state->icount;
/* update input line counters */
if (status & UART_MSR_TERI)
icount->rng++;
if (status & UART_MSR_DDSR)
icount->dsr++;
if (status & UART_MSR_DDCD) {
icount->dcd++;
#ifdef CONFIG_HARD_PPS
if ((info->flags & ASYNC_HARDPPS_CD) &&
(status & UART_MSR_DCD))
hardpps();
#endif
}
if (status & UART_MSR_DCTS)
icount->cts++;
wake_up_interruptible(&info->delta_msr_wait);
}
if ((info->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
printk("ttys%d CD now %s...", info->line,
(status & UART_MSR_DCD) ? "on" : "off");
#endif
if (status & UART_MSR_DCD)
wake_up_interruptible(&info->open_wait);
else {
#ifdef SERIAL_DEBUG_OPEN
printk("scheduling hangup...");
#endif
queue_task(&info->tqueue_hangup,
&tq_scheduler);
}
}
if (info->flags & ASYNC_CTS_FLOW) {
if (info->port.tty->hw_stopped) {
if (status & UART_MSR_CTS) {
#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
printk("CTS tx start...");
#endif
info->port.tty->hw_stopped = 0;
info->IER |= UART_IER_THRI;
serial_out(info, UART_IER, info->IER);
rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
return;
}
} else {
if (!(status & UART_MSR_CTS)) {
#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
printk("CTS tx stop...");
#endif
info->port.tty->hw_stopped = 1;
info->IER &= ~UART_IER_THRI;
serial_out(info, UART_IER, info->IER);
}
}
}
}
#endif
/*
* This is the serial driver's interrupt routine for a single port
*/
/* static void rs_360_interrupt(void *dev_id) */ /* until and if we start servicing irqs here */
static void rs_360_interrupt(int vec, void *dev_id)
{
u_char events;
int idx;
ser_info_t *info;
volatile struct smc_regs *smcp;
volatile struct scc_regs *sccp;
info = dev_id;
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
events = sccp->scc_scce;
if (events & SCCM_RX)
receive_chars(info);
if (events & SCCM_TX)
transmit_chars(info);
sccp->scc_scce = events;
} else {
smcp = &pquicc->smc_regs[idx];
events = smcp->smc_smce;
if (events & SMCM_BRKE)
receive_break(info);
if (events & SMCM_RX)
receive_chars(info);
if (events & SMCM_TX)
transmit_chars(info);
smcp->smc_smce = events;
}
#ifdef SERIAL_DEBUG_INTR
printk("rs_interrupt_single(%d, %x)...",
info->state->smc_scc_num, events);
#endif
#ifdef modem_control
check_modem_status(info);
#endif
info->last_active = jiffies;
#ifdef SERIAL_DEBUG_INTR
printk("end.\n");
#endif
}
/*
* -------------------------------------------------------------------
* Here ends the serial interrupt routines.
* -------------------------------------------------------------------
*/
static void do_softint(void *private_)
{
ser_info_t *info = (ser_info_t *) private_;
struct tty_struct *tty;
tty = info->port.tty;
if (!tty)
return;
if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
tty_wakeup(tty);
}
/*
* This routine is called from the scheduler tqueue when the interrupt
* routine has signalled that a hangup has occurred. The path of
* hangup processing is:
*
* serial interrupt routine -> (scheduler tqueue) ->
* do_serial_hangup() -> tty->hangup() -> rs_hangup()
*
*/
static void do_serial_hangup(void *private_)
{
struct async_struct *info = (struct async_struct *) private_;
struct tty_struct *tty;
tty = info->port.tty;
if (!tty)
return;
tty_hangup(tty);
}
static int startup(ser_info_t *info)
{
unsigned long flags;
int retval=0;
int idx;
/*struct serial_state *state = info->state;*/
volatile struct smc_regs *smcp;
volatile struct scc_regs *sccp;
volatile struct smc_uart_pram *up;
volatile struct uart_pram *scup;
local_irq_save(flags);
if (info->flags & ASYNC_INITIALIZED) {
goto errout;
}
#ifdef maybe
if (!state->port || !state->type) {
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
goto errout;
}
#endif
#ifdef SERIAL_DEBUG_OPEN
printk("starting up ttys%d (irq %d)...", info->line, state->irq);
#endif
#ifdef modem_control
info->MCR = 0;
if (info->port.tty->termios->c_cflag & CBAUD)
info->MCR = UART_MCR_DTR | UART_MCR_RTS;
#endif
if (info->port.tty)
clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
/*
* and set the speed of the serial port
*/
change_speed(info);
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
scup = &pquicc->pram[info->state->port].scc.pscc.u;
scup->mrblr = RX_BUF_SIZE;
scup->max_idl = RX_BUF_SIZE;
sccp->scc_sccm |= (UART_SCCM_TX | UART_SCCM_RX);
sccp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
} else {
smcp = &pquicc->smc_regs[idx];
/* Enable interrupts and I/O.
*/
smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
smcp->smc_smcmr |= (SMCMR_REN | SMCMR_TEN);
/* We can tune the buffer length and idle characters
* to take advantage of the entire incoming buffer size.
* If mrblr is something other than 1, maxidl has to be
* non-zero or we never get an interrupt. The maxidl
* is the number of character times we wait after reception
* of the last character before we decide no more characters
* are coming.
*/
/* up = (smc_uart_t *)&pquicc->cp_dparam[state->port]; */
/* holy unionized structures, Batman: */
up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
up->mrblr = RX_BUF_SIZE;
up->max_idl = RX_BUF_SIZE;
up->brkcr = 1; /* number of break chars */
}
info->flags |= ASYNC_INITIALIZED;
local_irq_restore(flags);
return 0;
errout:
local_irq_restore(flags);
return retval;
}
/*
* This routine will shutdown a serial port; interrupts are disabled, and
* DTR is dropped if the hangup on close termio flag is on.
*/
static void shutdown(ser_info_t *info)
{
unsigned long flags;
struct serial_state *state;
int idx;
volatile struct smc_regs *smcp;
volatile struct scc_regs *sccp;
if (!(info->flags & ASYNC_INITIALIZED))
return;
state = info->state;
#ifdef SERIAL_DEBUG_OPEN
printk("Shutting down serial port %d (irq %d)....", info->line,
state->irq);
#endif
local_irq_save(flags);
idx = PORT_NUM(state->smc_scc_num);
if (state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
sccp->scc_gsmr.w.low &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
#ifdef CONFIG_SERIAL_CONSOLE
/* We can't disable the transmitter if this is the
* system console.
*/
if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT)
#endif
sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX);
} else {
smcp = &pquicc->smc_regs[idx];
/* Disable interrupts and I/O.
*/
smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX);
#ifdef CONFIG_SERIAL_CONSOLE
/* We can't disable the transmitter if this is the
* system console.
*/
if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT)
#endif
smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
}
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
info->flags &= ~ASYNC_INITIALIZED;
local_irq_restore(flags);
}
/*
* This routine is called to set the UART divisor registers to match
* the specified baud rate for a serial port.
*/
static void change_speed(ser_info_t *info)
{
int baud_rate;
unsigned cflag, cval, scval, prev_mode;
int i, bits, sbits, idx;
unsigned long flags;
struct serial_state *state;
volatile struct smc_regs *smcp;
volatile struct scc_regs *sccp;
if (!info->port.tty || !info->port.tty->termios)
return;
cflag = info->port.tty->termios->c_cflag;
state = info->state;
/* Character length programmed into the mode register is the
* sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
* 1 or 2 stop bits, minus 1.
* The value 'bits' counts this for us.
*/
cval = 0;
scval = 0;
/* byte size and parity */
switch (cflag & CSIZE) {
case CS5: bits = 5; break;
case CS6: bits = 6; break;
case CS7: bits = 7; break;
case CS8: bits = 8; break;
/* Never happens, but GCC is too dumb to figure it out */
default: bits = 8; break;
}
sbits = bits - 5;
if (cflag & CSTOPB) {
cval |= SMCMR_SL; /* Two stops */
scval |= SCU_PMSR_SL;
bits++;
}
if (cflag & PARENB) {
cval |= SMCMR_PEN;
scval |= SCU_PMSR_PEN;
bits++;
}
if (!(cflag & PARODD)) {
cval |= SMCMR_PM_EVEN;
scval |= (SCU_PMSR_REVP | SCU_PMSR_TEVP);
}
/* Determine divisor based on baud rate */
i = cflag & CBAUD;
if (i >= (sizeof(baud_table)/sizeof(int)))
baud_rate = 9600;
else
baud_rate = baud_table[i];
info->timeout = (TX_BUF_SIZE*HZ*bits);
info->timeout += HZ/50; /* Add .02 seconds of slop */
#ifdef modem_control
/* CTS flow control flag and modem status interrupts */
info->IER &= ~UART_IER_MSI;
if (info->flags & ASYNC_HARDPPS_CD)
info->IER |= UART_IER_MSI;
if (cflag & CRTSCTS) {
info->flags |= ASYNC_CTS_FLOW;
info->IER |= UART_IER_MSI;
} else
info->flags &= ~ASYNC_CTS_FLOW;
if (cflag & CLOCAL)
info->flags &= ~ASYNC_CHECK_CD;
else {
info->flags |= ASYNC_CHECK_CD;
info->IER |= UART_IER_MSI;
}
serial_out(info, UART_IER, info->IER);
#endif
/*
* Set up parity check flag
*/
info->read_status_mask = (BD_SC_EMPTY | BD_SC_OV);
if (I_INPCK(info->port.tty))
info->read_status_mask |= BD_SC_FR | BD_SC_PR;
if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
info->read_status_mask |= BD_SC_BR;
/*
* Characters to ignore
*/
info->ignore_status_mask = 0;
if (I_IGNPAR(info->port.tty))
info->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
if (I_IGNBRK(info->port.tty)) {
info->ignore_status_mask |= BD_SC_BR;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
if (I_IGNPAR(info->port.tty))
info->ignore_status_mask |= BD_SC_OV;
}
/*
* !!! ignore all characters if CREAD is not set
*/
if ((cflag & CREAD) == 0)
info->read_status_mask &= ~BD_SC_EMPTY;
local_irq_save(flags);
/* Start bit has not been added (so don't, because we would just
* subtract it later), and we need to add one for the number of
* stops bits (there is always at least one).
*/
bits++;
idx = PORT_NUM(state->smc_scc_num);
if (state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
sccp->scc_psmr = (sbits << 12) | scval;
} else {
smcp = &pquicc->smc_regs[idx];
/* Set the mode register. We want to keep a copy of the
* enables, because we want to put them back if they were
* present.
*/
prev_mode = smcp->smc_smcmr;
smcp->smc_smcmr = smcr_mk_clen(bits) | cval | SMCMR_SM_UART;
smcp->smc_smcmr |= (prev_mode & (SMCMR_REN | SMCMR_TEN));
}
m360_cpm_setbrg((state - rs_table), baud_rate);
local_irq_restore(flags);
}
static void rs_360_put_char(struct tty_struct *tty, unsigned char ch)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
volatile QUICC_BD *bdp;
if (serial_paranoia_check(info, tty->name, "rs_put_char"))
return 0;
if (!tty)
return 0;
bdp = info->tx_cur;
while (bdp->status & BD_SC_READY);
/* *((char *)__va(bdp->buf)) = ch; */
*((char *)bdp->buf) = ch;
bdp->length = 1;
bdp->status |= BD_SC_READY;
/* Get next BD.
*/
if (bdp->status & BD_SC_WRAP)
bdp = info->tx_bd_base;
else
bdp++;
info->tx_cur = (QUICC_BD *)bdp;
return 1;
}
static int rs_360_write(struct tty_struct * tty,
const unsigned char *buf, int count)
{
int c, ret = 0;
ser_info_t *info = (ser_info_t *)tty->driver_data;
volatile QUICC_BD *bdp;
#ifdef CONFIG_KGDB
/* Try to let stub handle output. Returns true if it did. */
if (kgdb_output_string(buf, count))
return ret;
#endif
if (serial_paranoia_check(info, tty->name, "rs_write"))
return 0;
if (!tty)
return 0;
bdp = info->tx_cur;
while (1) {
c = min(count, TX_BUF_SIZE);
if (c <= 0)
break;
if (bdp->status & BD_SC_READY) {
info->flags |= TX_WAKEUP;
break;
}
/* memcpy(__va(bdp->buf), buf, c); */
memcpy((void *)bdp->buf, buf, c);
bdp->length = c;
bdp->status |= BD_SC_READY;
buf += c;
count -= c;
ret += c;
/* Get next BD.
*/
if (bdp->status & BD_SC_WRAP)
bdp = info->tx_bd_base;
else
bdp++;
info->tx_cur = (QUICC_BD *)bdp;
}
return ret;
}
static int rs_360_write_room(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
int ret;
if (serial_paranoia_check(info, tty->name, "rs_write_room"))
return 0;
if ((info->tx_cur->status & BD_SC_READY) == 0) {
info->flags &= ~TX_WAKEUP;
ret = TX_BUF_SIZE;
}
else {
info->flags |= TX_WAKEUP;
ret = 0;
}
return ret;
}
/* I could track this with transmit counters....maybe later.
*/
static int rs_360_chars_in_buffer(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer"))
return 0;
return 0;
}
static void rs_360_flush_buffer(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
return;
/* There is nothing to "flush", whatever we gave the CPM
* is on its way out.
*/
tty_wakeup(tty);
info->flags &= ~TX_WAKEUP;
}
/*
* This function is used to send a high-priority XON/XOFF character to
* the device
*/
static void rs_360_send_xchar(struct tty_struct *tty, char ch)
{
volatile QUICC_BD *bdp;
ser_info_t *info = (ser_info_t *)tty->driver_data;
if (serial_paranoia_check(info, tty->name, "rs_send_char"))
return;
bdp = info->tx_cur;
while (bdp->status & BD_SC_READY);
/* *((char *)__va(bdp->buf)) = ch; */
*((char *)bdp->buf) = ch;
bdp->length = 1;
bdp->status |= BD_SC_READY;
/* Get next BD.
*/
if (bdp->status & BD_SC_WRAP)
bdp = info->tx_bd_base;
else
bdp++;
info->tx_cur = (QUICC_BD *)bdp;
}
/*
* ------------------------------------------------------------
* rs_throttle()
*
* This routine is called by the upper-layer tty layer to signal that
* incoming characters should be throttled.
* ------------------------------------------------------------
*/
static void rs_360_throttle(struct tty_struct * tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
#ifdef SERIAL_DEBUG_THROTTLE
char buf[64];
printk("throttle %s: %d....\n", _tty_name(tty, buf),
tty->ldisc.chars_in_buffer(tty));
#endif
if (serial_paranoia_check(info, tty->name, "rs_throttle"))
return;
if (I_IXOFF(tty))
rs_360_send_xchar(tty, STOP_CHAR(tty));
#ifdef modem_control
if (tty->termios->c_cflag & CRTSCTS)
info->MCR &= ~UART_MCR_RTS;
local_irq_disable();
serial_out(info, UART_MCR, info->MCR);
local_irq_enable();
#endif
}
static void rs_360_unthrottle(struct tty_struct * tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
#ifdef SERIAL_DEBUG_THROTTLE
char buf[64];
printk("unthrottle %s: %d....\n", _tty_name(tty, buf),
tty->ldisc.chars_in_buffer(tty));
#endif
if (serial_paranoia_check(info, tty->name, "rs_unthrottle"))
return;
if (I_IXOFF(tty)) {
if (info->x_char)
info->x_char = 0;
else
rs_360_send_xchar(tty, START_CHAR(tty));
}
#ifdef modem_control
if (tty->termios->c_cflag & CRTSCTS)
info->MCR |= UART_MCR_RTS;
local_irq_disable();
serial_out(info, UART_MCR, info->MCR);
local_irq_enable();
#endif
}
/*
* ------------------------------------------------------------
* rs_ioctl() and friends
* ------------------------------------------------------------
*/
#ifdef maybe
/*
* get_lsr_info - get line status register info
*
* Purpose: Let user call ioctl() to get info when the UART physically
* is emptied. On bus types like RS485, the transmitter must
* release the bus after transmitting. This must be done when
* the transmit shift register is empty, not be done when the
* transmit holding register is empty. This functionality
* allows an RS485 driver to be written in user space.
*/
static int get_lsr_info(struct async_struct * info, unsigned int *value)
{
unsigned char status;
unsigned int result;
local_irq_disable();
status = serial_in(info, UART_LSR);
local_irq_enable();
result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
return put_user(result,value);
}
#endif
static int rs_360_tiocmget(struct tty_struct *tty, struct file *file)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
unsigned int result = 0;
#ifdef modem_control
unsigned char control, status;
if (serial_paranoia_check(info, tty->name, __func__))
return -ENODEV;
if (tty->flags & (1 << TTY_IO_ERROR))
return -EIO;
control = info->MCR;
local_irq_disable();
status = serial_in(info, UART_MSR);
local_irq_enable();
result = ((control & UART_MCR_RTS) ? TIOCM_RTS : 0)
| ((control & UART_MCR_DTR) ? TIOCM_DTR : 0)
#ifdef TIOCM_OUT1
| ((control & UART_MCR_OUT1) ? TIOCM_OUT1 : 0)
| ((control & UART_MCR_OUT2) ? TIOCM_OUT2 : 0)
#endif
| ((status & UART_MSR_DCD) ? TIOCM_CAR : 0)
| ((status & UART_MSR_RI) ? TIOCM_RNG : 0)
| ((status & UART_MSR_DSR) ? TIOCM_DSR : 0)
| ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
#endif
return result;
}
static int rs_360_tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
#ifdef modem_control
ser_info_t *info = (ser_info_t *)tty->driver_data;
unsigned int arg;
if (serial_paranoia_check(info, tty->name, __func__))
return -ENODEV;
if (tty->flags & (1 << TTY_IO_ERROR))
return -EIO;
/* FIXME: locking on info->mcr */
if (set & TIOCM_RTS)
info->mcr |= UART_MCR_RTS;
if (set & TIOCM_DTR)
info->mcr |= UART_MCR_DTR;
if (clear & TIOCM_RTS)
info->MCR &= ~UART_MCR_RTS;
if (clear & TIOCM_DTR)
info->MCR &= ~UART_MCR_DTR;
#ifdef TIOCM_OUT1
if (set & TIOCM_OUT1)
info->MCR |= UART_MCR_OUT1;
if (set & TIOCM_OUT2)
info->MCR |= UART_MCR_OUT2;
if (clear & TIOCM_OUT1)
info->MCR &= ~UART_MCR_OUT1;
if (clear & TIOCM_OUT2)
info->MCR &= ~UART_MCR_OUT2;
#endif
local_irq_disable();
serial_out(info, UART_MCR, info->MCR);
local_irq_enable();
#endif
return 0;
}
/* Sending a break is a two step process on the SMC/SCC. It is accomplished
* by sending a STOP TRANSMIT command followed by a RESTART TRANSMIT
* command. We take advantage of the begin/end functions to make this
* happen.
*/
static ushort smc_chan_map[] = {
CPM_CR_CH_SMC1,
CPM_CR_CH_SMC2
};
static ushort scc_chan_map[] = {
CPM_CR_CH_SCC1,
CPM_CR_CH_SCC2,
CPM_CR_CH_SCC3,
CPM_CR_CH_SCC4
};
static void begin_break(ser_info_t *info)
{
volatile QUICC *cp;
ushort chan;
int idx;
cp = pquicc;
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC)
chan = scc_chan_map[idx];
else
chan = smc_chan_map[idx];
cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG;
while (cp->cp_cr & CPM_CR_FLG);
}
static void end_break(ser_info_t *info)
{
volatile QUICC *cp;
ushort chan;
int idx;
cp = pquicc;
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC)
chan = scc_chan_map[idx];
else
chan = smc_chan_map[idx];
cp->cp_cr = mk_cr_cmd(chan, CPM_CR_RESTART_TX) | CPM_CR_FLG;
while (cp->cp_cr & CPM_CR_FLG);
}
/*
* This routine sends a break character out the serial port.
*/
static void send_break(ser_info_t *info, unsigned int duration)
{
#ifdef SERIAL_DEBUG_SEND_BREAK
printk("rs_send_break(%d) jiff=%lu...", duration, jiffies);
#endif
begin_break(info);
msleep_interruptible(duration);
end_break(info);
#ifdef SERIAL_DEBUG_SEND_BREAK
printk("done jiffies=%lu\n", jiffies);
#endif
}
static int rs_360_ioctl(struct tty_struct *tty, struct file * file,
unsigned int cmd, unsigned long arg)
{
int error;
ser_info_t *info = (ser_info_t *)tty->driver_data;
int retval;
struct async_icount cnow;
/* struct async_icount_24 cnow;*/ /* kernel counter temps */
struct serial_icounter_struct *p_cuser; /* user space */
if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
return -ENODEV;
if ((cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
if (tty->flags & (1 << TTY_IO_ERROR))
return -EIO;
}
switch (cmd) {
case TCSBRK: /* SVID version: non-zero arg --> no break */
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
if (signal_pending(current))
return -EINTR;
if (!arg) {
send_break(info, 250); /* 1/4 second */
if (signal_pending(current))
return -EINTR;
}
return 0;
case TCSBRKP: /* support for POSIX tcsendbreak() */
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
if (signal_pending(current))
return -EINTR;
send_break(info, arg ? arg*100 : 250);
if (signal_pending(current))
return -EINTR;
return 0;
case TIOCSBRK:
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
begin_break(info);
return 0;
case TIOCCBRK:
retval = tty_check_change(tty);
if (retval)
return retval;
end_break(info);
return 0;
#ifdef maybe
case TIOCSERGETLSR: /* Get line status register */
return get_lsr_info(info, (unsigned int *) arg);
#endif
/*
* Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
* - mask passed in arg for lines of interest
* (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
* Caller should use TIOCGICOUNT to see which one it was
*/
case TIOCMIWAIT:
#ifdef modem_control
local_irq_disable();
/* note the counters on entry */
cprev = info->state->icount;
local_irq_enable();
while (1) {
interruptible_sleep_on(&info->delta_msr_wait);
/* see if a signal did it */
if (signal_pending(current))
return -ERESTARTSYS;
local_irq_disable();
cnow = info->state->icount; /* atomic copy */
local_irq_enable();
if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
return -EIO; /* no change => error */
if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) {
return 0;
}
cprev = cnow;
}
/* NOTREACHED */
#else
return 0;
#endif
/*
* Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
* Return: write counters to the user passed counter struct
* NB: both 1->0 and 0->1 transitions are counted except for
* RI where only 0->1 is counted.
*/
case TIOCGICOUNT:
local_irq_disable();
cnow = info->state->icount;
local_irq_enable();
p_cuser = (struct serial_icounter_struct *) arg;
/* error = put_user(cnow.cts, &p_cuser->cts); */
/* if (error) return error; */
/* error = put_user(cnow.dsr, &p_cuser->dsr); */
/* if (error) return error; */
/* error = put_user(cnow.rng, &p_cuser->rng); */
/* if (error) return error; */
/* error = put_user(cnow.dcd, &p_cuser->dcd); */
/* if (error) return error; */
put_user(cnow.cts, &p_cuser->cts);
put_user(cnow.dsr, &p_cuser->dsr);
put_user(cnow.rng, &p_cuser->rng);
put_user(cnow.dcd, &p_cuser->dcd);
return 0;
default:
return -ENOIOCTLCMD;
}
return 0;
}
/* FIX UP modem control here someday......
*/
static void rs_360_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
change_speed(info);
#ifdef modem_control
/* Handle transition to B0 status */
if ((old_termios->c_cflag & CBAUD) &&
!(tty->termios->c_cflag & CBAUD)) {
info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);
local_irq_disable();
serial_out(info, UART_MCR, info->MCR);
local_irq_enable();
}
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
(tty->termios->c_cflag & CBAUD)) {
info->MCR |= UART_MCR_DTR;
if (!tty->hw_stopped ||
!(tty->termios->c_cflag & CRTSCTS)) {
info->MCR |= UART_MCR_RTS;
}
local_irq_disable();
serial_out(info, UART_MCR, info->MCR);
local_irq_enable();
}
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
!(tty->termios->c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
rs_360_start(tty);
}
#endif
#if 0
/*
* No need to wake up processes in open wait, since they
* sample the CLOCAL flag once, and don't recheck it.
* XXX It's not clear whether the current behavior is correct
* or not. Hence, this may change.....
*/
if (!(old_termios->c_cflag & CLOCAL) &&
(tty->termios->c_cflag & CLOCAL))
wake_up_interruptible(&info->open_wait);
#endif
}
/*
* ------------------------------------------------------------
* rs_close()
*
* This routine is called when the serial port gets closed. First, we
* wait for the last remaining data to be sent. Then, we unlink its
* async structure from the interrupt chain if necessary, and we free
* that IRQ if nothing is left in the chain.
* ------------------------------------------------------------
*/
static void rs_360_close(struct tty_struct *tty, struct file * filp)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
/* struct async_state *state; */
struct serial_state *state;
unsigned long flags;
int idx;
volatile struct smc_regs *smcp;
volatile struct scc_regs *sccp;
if (!info || serial_paranoia_check(info, tty->name, "rs_close"))
return;
state = info->state;
local_irq_save(flags);
if (tty_hung_up_p(filp)) {
DBG_CNT("before DEC-hung");
local_irq_restore(flags);
return;
}
#ifdef SERIAL_DEBUG_OPEN
printk("rs_close ttys%d, count = %d\n", info->line, state->count);
#endif
if ((tty->count == 1) && (state->count != 1)) {
/*
* Uh, oh. tty->count is 1, which means that the tty
* structure will be freed. state->count should always
* be one in these conditions. If it's greater than
* one, we've got real problems, since it means the
* serial port won't be shutdown.
*/
printk("rs_close: bad serial port count; tty->count is 1, "
"state->count is %d\n", state->count);
state->count = 1;
}
if (--state->count < 0) {
printk("rs_close: bad serial port count for ttys%d: %d\n",
info->line, state->count);
state->count = 0;
}
if (state->count) {
DBG_CNT("before DEC-2");
local_irq_restore(flags);
return;
}
info->flags |= ASYNC_CLOSING;
/*
* Now we wait for the transmit buffer to clear; and we notify
* the line discipline to only process XON/XOFF characters.
*/
tty->closing = 1;
if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
tty_wait_until_sent(tty, info->closing_wait);
/*
* At this point we stop accepting input. To do this, we
* disable the receive line status interrupts, and tell the
* interrupt driver to stop checking the data ready bit in the
* line status register.
*/
info->read_status_mask &= ~BD_SC_EMPTY;
if (info->flags & ASYNC_INITIALIZED) {
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
sccp = &pquicc->scc_regs[idx];
sccp->scc_sccm &= ~UART_SCCM_RX;
sccp->scc_gsmr.w.low &= ~SCC_GSMRL_ENR;
} else {
smcp = &pquicc->smc_regs[idx];
smcp->smc_smcm &= ~SMCM_RX;
smcp->smc_smcmr &= ~SMCMR_REN;
}
/*
* Before we drop DTR, make sure the UART transmitter
* has completely drained; this is especially
* important if there is a transmit FIFO!
*/
rs_360_wait_until_sent(tty, info->timeout);
}
shutdown(info);
rs_360_flush_buffer(tty);
tty_ldisc_flush(tty);
tty->closing = 0;
info->event = 0;
info->port.tty = NULL;
if (info->blocked_open) {
if (info->close_delay) {
msleep_interruptible(jiffies_to_msecs(info->close_delay));
}
wake_up_interruptible(&info->open_wait);
}
info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
wake_up_interruptible(&info->close_wait);
local_irq_restore(flags);
}
/*
* rs_wait_until_sent() --- wait until the transmitter is empty
*/
static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
unsigned long orig_jiffies, char_time;
/*int lsr;*/
volatile QUICC_BD *bdp;
if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent"))
return;
#ifdef maybe
if (info->state->type == PORT_UNKNOWN)
return;
#endif
orig_jiffies = jiffies;
/*
* Set the check interval to be 1/5 of the estimated time to
* send a single character, and make it at least 1. The check
* interval should also be less than the timeout.
*
* Note: we have to use pretty tight timings here to satisfy
* the NIST-PCTS.
*/
char_time = 1;
if (timeout)
char_time = min(char_time, (unsigned long)timeout);
#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time);
printk("jiff=%lu...", jiffies);
#endif
tty_lock_nested(); /* always held already since we come from ->close */
/* We go through the loop at least once because we can't tell
* exactly when the last character exits the shifter. There can
* be at least two characters waiting to be sent after the buffers
* are empty.
*/
do {
#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
printk("lsr = %d (jiff=%lu)...", lsr, jiffies);
#endif
/* current->counter = 0; make us low-priority */
msleep_interruptible(jiffies_to_msecs(char_time));
if (signal_pending(current))
break;
if (timeout && (time_after(jiffies, orig_jiffies + timeout)))
break;
/* The 'tx_cur' is really the next buffer to send. We
* have to back up to the previous BD and wait for it
* to go. This isn't perfect, because all this indicates
* is the buffer is available. There are still characters
* in the CPM FIFO.
*/
bdp = info->tx_cur;
if (bdp == info->tx_bd_base)
bdp += (TX_NUM_FIFO-1);
else
bdp--;
} while (bdp->status & BD_SC_READY);
current->state = TASK_RUNNING;
tty_unlock();
#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
#endif
}
/*
* rs_hangup() --- called by tty_hangup() when a hangup is signaled.
*/
static void rs_360_hangup(struct tty_struct *tty)
{
ser_info_t *info = (ser_info_t *)tty->driver_data;
struct serial_state *state = info->state;
if (serial_paranoia_check(info, tty->name, "rs_hangup"))
return;
state = info->state;
rs_360_flush_buffer(tty);
shutdown(info);
info->event = 0;
state->count = 0;
info->flags &= ~ASYNC_NORMAL_ACTIVE;
info->port.tty = NULL;
wake_up_interruptible(&info->open_wait);
}
/*
* ------------------------------------------------------------
* rs_open() and friends
* ------------------------------------------------------------
*/
static int block_til_ready(struct tty_struct *tty, struct file * filp,
ser_info_t *info)
{
#ifdef DO_THIS_LATER
DECLARE_WAITQUEUE(wait, current);
#endif
struct serial_state *state = info->state;
int retval;
int do_clocal = 0;
/*
* If the device is in the middle of being closed, then block
* until it's done, and then try again.
*/
if (tty_hung_up_p(filp) ||
(info->flags & ASYNC_CLOSING)) {
if (info->flags & ASYNC_CLOSING)
interruptible_sleep_on(&info->close_wait);
#ifdef SERIAL_DO_RESTART
if (info->flags & ASYNC_HUP_NOTIFY)
return -EAGAIN;
else
return -ERESTARTSYS;
#else
return -EAGAIN;
#endif
}
/*
* If non-blocking mode is set, or the port is not enabled,
* then make the check up front and then exit.
* If this is an SMC port, we don't have modem control to wait
* for, so just get out here.
*/
if ((filp->f_flags & O_NONBLOCK) ||
(tty->flags & (1 << TTY_IO_ERROR)) ||
!(info->state->smc_scc_num & NUM_IS_SCC)) {
info->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
if (tty->termios->c_cflag & CLOCAL)
do_clocal = 1;
/*
* Block waiting for the carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
* this loop, state->count is dropped by one, so that
* rs_close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
#ifdef DO_THIS_LATER
add_wait_queue(&info->open_wait, &wait);
#ifdef SERIAL_DEBUG_OPEN
printk("block_til_ready before block: ttys%d, count = %d\n",
state->line, state->count);
#endif
local_irq_disable();
if (!tty_hung_up_p(filp))
state->count--;
local_irq_enable();
info->blocked_open++;
while (1) {
local_irq_disable();
if (tty->termios->c_cflag & CBAUD)
serial_out(info, UART_MCR,
serial_inp(info, UART_MCR) |
(UART_MCR_DTR | UART_MCR_RTS));
local_irq_enable();
set_current_state(TASK_INTERRUPTIBLE);
if (tty_hung_up_p(filp) ||
!(info->flags & ASYNC_INITIALIZED)) {
#ifdef SERIAL_DO_RESTART
if (info->flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
else
retval = -ERESTARTSYS;
#else
retval = -EAGAIN;
#endif
break;
}
if (!(info->flags & ASYNC_CLOSING) &&
(do_clocal || (serial_in(info, UART_MSR) &
UART_MSR_DCD)))
break;
if (signal_pending(current)) {
retval = -ERESTARTSYS;
break;
}
#ifdef SERIAL_DEBUG_OPEN
printk("block_til_ready blocking: ttys%d, count = %d\n",
info->line, state->count);
#endif
schedule();
}
current->state = TASK_RUNNING;
remove_wait_queue(&info->open_wait, &wait);
if (!tty_hung_up_p(filp))
state->count++;
info->blocked_open--;
#ifdef SERIAL_DEBUG_OPEN
printk("block_til_ready after blocking: ttys%d, count = %d\n",
info->line, state->count);
#endif
#endif /* DO_THIS_LATER */
if (retval)
return retval;
info->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
static int get_async_struct(int line, ser_info_t **ret_info)
{
struct serial_state *sstate;
sstate = rs_table + line;
if (sstate->info) {
sstate->count++;
*ret_info = (ser_info_t *)sstate->info;
return 0;
}
else {
return -ENOMEM;
}
}
/*
* This routine is called whenever a serial port is opened. It
* enables interrupts for a serial port, linking in its async structure into
* the IRQ chain. It also performs the serial-specific
* initialization for the tty structure.
*/
static int rs_360_open(struct tty_struct *tty, struct file * filp)
{
ser_info_t *info;
int retval, line;
line = tty->index;
if ((line < 0) || (line >= NR_PORTS))
return -ENODEV;
retval = get_async_struct(line, &info);
if (retval)
return retval;
if (serial_paranoia_check(info, tty->name, "rs_open"))
return -ENODEV;
#ifdef SERIAL_DEBUG_OPEN
printk("rs_open %s, count = %d\n", tty->name, info->state->count);
#endif
tty->driver_data = info;
info->port.tty = tty;
/*
* Start up serial port
*/
retval = startup(info);
if (retval)
return retval;
retval = block_til_ready(tty, filp, info);
if (retval) {
#ifdef SERIAL_DEBUG_OPEN
printk("rs_open returning after block_til_ready with %d\n",
retval);
#endif
return retval;
}
#ifdef SERIAL_DEBUG_OPEN
printk("rs_open %s successful...", tty->name);
#endif
return 0;
}
/*
* /proc fs routines....
*/
static inline int line_info(char *buf, struct serial_state *state)
{
#ifdef notdef
struct async_struct *info = state->info, scr_info;
char stat_buf[30], control, status;
#endif
int ret;
ret = sprintf(buf, "%d: uart:%s port:%X irq:%d",
state->line,
(state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC",
(unsigned int)(state->port), state->irq);
if (!state->port || (state->type == PORT_UNKNOWN)) {
ret += sprintf(buf+ret, "\n");
return ret;
}
#ifdef notdef
/*
* Figure out the current RS-232 lines
*/
if (!info) {
info = &scr_info; /* This is just for serial_{in,out} */
info->magic = SERIAL_MAGIC;
info->port = state->port;
info->flags = state->flags;
info->quot = 0;
info->port.tty = NULL;
}
local_irq_disable();
status = serial_in(info, UART_MSR);
control = info ? info->MCR : serial_in(info, UART_MCR);
local_irq_enable();
stat_buf[0] = 0;
stat_buf[1] = 0;
if (control & UART_MCR_RTS)
strcat(stat_buf, "|RTS");
if (status & UART_MSR_CTS)
strcat(stat_buf, "|CTS");
if (control & UART_MCR_DTR)
strcat(stat_buf, "|DTR");
if (status & UART_MSR_DSR)
strcat(stat_buf, "|DSR");
if (status & UART_MSR_DCD)
strcat(stat_buf, "|CD");
if (status & UART_MSR_RI)
strcat(stat_buf, "|RI");
if (info->quot) {
ret += sprintf(buf+ret, " baud:%d",
state->baud_base / info->quot);
}
ret += sprintf(buf+ret, " tx:%d rx:%d",
state->icount.tx, state->icount.rx);
if (state->icount.frame)
ret += sprintf(buf+ret, " fe:%d", state->icount.frame);
if (state->icount.parity)
ret += sprintf(buf+ret, " pe:%d", state->icount.parity);
if (state->icount.brk)
ret += sprintf(buf+ret, " brk:%d", state->icount.brk);
if (state->icount.overrun)
ret += sprintf(buf+ret, " oe:%d", state->icount.overrun);
/*
* Last thing is the RS-232 status lines
*/
ret += sprintf(buf+ret, " %s\n", stat_buf+1);
#endif
return ret;
}
int rs_360_read_proc(char *page, char **start, off_t off, int count,
int *eof, void *data)
{
int i, len = 0;
off_t begin = 0;
len += sprintf(page, "serinfo:1.0 driver:%s\n", serial_version);
for (i = 0; i < NR_PORTS && len < 4000; i++) {
len += line_info(page + len, &rs_table[i]);
if (len+begin > off+count)
goto done;
if (len+begin < off) {
begin += len;
len = 0;
}
}
*eof = 1;
done:
if (off >= len+begin)
return 0;
*start = page + (begin-off);
return ((count < begin+len-off) ? count : begin+len-off);
}
/*
* ---------------------------------------------------------------------
* rs_init() and friends
*
* rs_init() is called at boot-time to initialize the serial driver.
* ---------------------------------------------------------------------
*/
/*
* This routine prints out the appropriate serial driver version
* number, and identifies which options were configured into this
* driver.
*/
static _INLINE_ void show_serial_version(void)
{
printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
}
/*
* The serial console driver used during boot. Note that these names
* clash with those found in "serial.c", so we currently can't support
* the 16xxx uarts and these at the same time. I will fix this to become
* an indirect function call from tty_io.c (or something).
*/
#ifdef CONFIG_SERIAL_CONSOLE
/*
* Print a string to the serial port trying not to disturb any possible
* real use of the port...
*/
static void my_console_write(int idx, const char *s,
unsigned count)
{
struct serial_state *ser;
ser_info_t *info;
unsigned i;
QUICC_BD *bdp, *bdbase;
volatile struct smc_uart_pram *up;
volatile u_char *cp;
ser = rs_table + idx;
/* If the port has been initialized for general use, we have
* to use the buffer descriptors allocated there. Otherwise,
* we simply use the single buffer allocated.
*/
if ((info = (ser_info_t *)ser->info) != NULL) {
bdp = info->tx_cur;
bdbase = info->tx_bd_base;
}
else {
/* Pointer to UART in parameter ram.
*/
/* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */
up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u;
/* Get the address of the host memory buffer.
*/
bdp = bdbase = (QUICC_BD *)((uint)pquicc + (uint)up->tbase);
}
/*
* We need to gracefully shut down the transmitter, disable
* interrupts, then send our bytes out.
*/
/*
* Now, do each character. This is not as bad as it looks
* since this is a holding FIFO and not a transmitting FIFO.
* We could add the complexity of filling the entire transmit
* buffer, but we would just wait longer between accesses......
*/
for (i = 0; i < count; i++, s++) {
/* Wait for transmitter fifo to empty.
* Ready indicates output is ready, and xmt is doing
* that, not that it is ready for us to send.
*/
while (bdp->status & BD_SC_READY);
/* Send the character out.
*/
cp = bdp->buf;
*cp = *s;
bdp->length = 1;
bdp->status |= BD_SC_READY;
if (bdp->status & BD_SC_WRAP)
bdp = bdbase;
else
bdp++;
/* if a LF, also do CR... */
if (*s == 10) {
while (bdp->status & BD_SC_READY);
/* cp = __va(bdp->buf); */
cp = bdp->buf;
*cp = 13;
bdp->length = 1;
bdp->status |= BD_SC_READY;
if (bdp->status & BD_SC_WRAP) {
bdp = bdbase;
}
else {
bdp++;
}
}
}
/*
* Finally, Wait for transmitter & holding register to empty
* and restore the IER
*/
while (bdp->status & BD_SC_READY);
if (info)
info->tx_cur = (QUICC_BD *)bdp;
}
static void serial_console_write(struct console *c, const char *s,
unsigned count)
{
#ifdef CONFIG_KGDB
/* Try to let stub handle output. Returns true if it did. */
if (kgdb_output_string(s, count))
return;
#endif
my_console_write(c->index, s, count);
}
/*void console_print_68360(const char *p)
{
const char *cp = p;
int i;
for (i=0;cp[i]!=0;i++);
serial_console_write (p, i);
//Comment this if you want to have a strict interrupt-driven output
//rs_fair_output();
return;
}*/
#ifdef CONFIG_XMON
int
xmon_360_write(const char *s, unsigned count)
{
my_console_write(0, s, count);
return(count);
}
#endif
#ifdef CONFIG_KGDB
void
putDebugChar(char ch)
{
my_console_write(0, &ch, 1);
}
#endif
/*
* Receive character from the serial port. This only works well
* before the port is initialized for real use.
*/
static int my_console_wait_key(int idx, int xmon, char *obuf)
{
struct serial_state *ser;
u_char c, *cp;
ser_info_t *info;
QUICC_BD *bdp;
volatile struct smc_uart_pram *up;
int i;
ser = rs_table + idx;
/* Get the address of the host memory buffer.
* If the port has been initialized for general use, we must
* use information from the port structure.
*/
if ((info = (ser_info_t *)ser->info))
bdp = info->rx_cur;
else
/* bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase]; */
bdp = (QUICC_BD *)((uint)pquicc + (uint)up->tbase);
/* Pointer to UART in parameter ram.
*/
/* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */
up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
/*
* We need to gracefully shut down the receiver, disable
* interrupts, then read the input.
* XMON just wants a poll. If no character, return -1, else
* return the character.
*/
if (!xmon) {
while (bdp->status & BD_SC_EMPTY);
}
else {
if (bdp->status & BD_SC_EMPTY)
return -1;
}
cp = (char *)bdp->buf;
if (obuf) {
i = c = bdp->length;
while (i-- > 0)
*obuf++ = *cp++;
}
else {
c = *cp;
}
bdp->status |= BD_SC_EMPTY;
if (info) {
if (bdp->status & BD_SC_WRAP) {
bdp = info->rx_bd_base;
}
else {
bdp++;
}
info->rx_cur = (QUICC_BD *)bdp;
}
return((int)c);
}
static int serial_console_wait_key(struct console *co)
{
return(my_console_wait_key(co->index, 0, NULL));
}
#ifdef CONFIG_XMON
int
xmon_360_read_poll(void)
{
return(my_console_wait_key(0, 1, NULL));
}
int
xmon_360_read_char(void)
{
return(my_console_wait_key(0, 0, NULL));
}
#endif
#ifdef CONFIG_KGDB
static char kgdb_buf[RX_BUF_SIZE], *kgdp;
static int kgdb_chars;
unsigned char
getDebugChar(void)
{
if (kgdb_chars <= 0) {
kgdb_chars = my_console_wait_key(0, 0, kgdb_buf);
kgdp = kgdb_buf;
}
kgdb_chars--;
return(*kgdp++);
}
void kgdb_interruptible(int state)
{
}
void kgdb_map_scc(void)
{
struct serial_state *ser;
uint mem_addr;
volatile QUICC_BD *bdp;
volatile smc_uart_t *up;
cpmp = (cpm360_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
/* To avoid data cache CPM DMA coherency problems, allocate a
* buffer in the CPM DPRAM. This will work until the CPM and
* serial ports are initialized. At that time a memory buffer
* will be allocated.
* The port is already initialized from the boot procedure, all
* we do here is give it a different buffer and make it a FIFO.
*/
ser = rs_table;
/* Right now, assume we are using SMCs.
*/
up = (smc_uart_t *)&cpmp->cp_dparam[ser->port];
/* Allocate space for an input FIFO, plus a few bytes for output.
* Allocate bytes to maintain word alignment.
*/
mem_addr = (uint)(&cpmp->cp_dpmem[0x1000]);
/* Set the physical address of the host memory buffers in
* the buffer descriptors.
*/
bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase];
bdp->buf = mem_addr;
bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_tbase];
bdp->buf = mem_addr+RX_BUF_SIZE;
up->smc_mrblr = RX_BUF_SIZE; /* receive buffer length */
up->smc_maxidl = RX_BUF_SIZE;
}
#endif
static struct tty_struct *serial_console_device(struct console *c, int *index)
{
*index = c->index;
return serial_driver;
}
struct console sercons = {
.name = "ttyS",
.write = serial_console_write,
.device = serial_console_device,
.wait_key = serial_console_wait_key,
.setup = serial_console_setup,
.flags = CON_PRINTBUFFER,
.index = CONFIG_SERIAL_CONSOLE_PORT,
};
/*
* Register console.
*/
long console_360_init(long kmem_start, long kmem_end)
{
register_console(&sercons);
/*register_console (console_print_68360); - 2.0.38 only required a write
function pointer. */
return kmem_start;
}
#endif
/* Index in baud rate table of the default console baud rate.
*/
static int baud_idx;
static const struct tty_operations rs_360_ops = {
.owner = THIS_MODULE,
.open = rs_360_open,
.close = rs_360_close,
.write = rs_360_write,
.put_char = rs_360_put_char,
.write_room = rs_360_write_room,
.chars_in_buffer = rs_360_chars_in_buffer,
.flush_buffer = rs_360_flush_buffer,
.ioctl = rs_360_ioctl,
.throttle = rs_360_throttle,
.unthrottle = rs_360_unthrottle,
/* .send_xchar = rs_360_send_xchar, */
.set_termios = rs_360_set_termios,
.stop = rs_360_stop,
.start = rs_360_start,
.hangup = rs_360_hangup,
/* .wait_until_sent = rs_360_wait_until_sent, */
/* .read_proc = rs_360_read_proc, */
.tiocmget = rs_360_tiocmget,
.tiocmset = rs_360_tiocmset,
};
static int __init rs_360_init(void)
{
struct serial_state * state;
ser_info_t *info;
void *mem_addr;
uint dp_addr, iobits;
int i, j, idx;
ushort chan;
QUICC_BD *bdp;
volatile QUICC *cp;
volatile struct smc_regs *sp;
volatile struct smc_uart_pram *up;
volatile struct scc_regs *scp;
volatile struct uart_pram *sup;
/* volatile immap_t *immap; */
serial_driver = alloc_tty_driver(NR_PORTS);
if (!serial_driver)
return -1;
show_serial_version();
serial_driver->name = "ttyS";
serial_driver->major = TTY_MAJOR;
serial_driver->minor_start = 64;
serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
serial_driver->subtype = SERIAL_TYPE_NORMAL;
serial_driver->init_termios = tty_std_termios;
serial_driver->init_termios.c_cflag =
baud_idx | CS8 | CREAD | HUPCL | CLOCAL;
serial_driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(serial_driver, &rs_360_ops);
if (tty_register_driver(serial_driver))
panic("Couldn't register serial driver\n");
cp = pquicc; /* Get pointer to Communication Processor */
/* immap = (immap_t *)IMAP_ADDR; */ /* and to internal registers */
/* Configure SCC2, SCC3, and SCC4 instead of port A parallel I/O.
*/
/* The "standard" configuration through the 860.
*/
/* immap->im_ioport.iop_papar |= 0x00fc; */
/* immap->im_ioport.iop_padir &= ~0x00fc; */
/* immap->im_ioport.iop_paodr &= ~0x00fc; */
cp->pio_papar |= 0x00fc;
cp->pio_padir &= ~0x00fc;
/* cp->pio_paodr &= ~0x00fc; */
/* Since we don't yet do modem control, connect the port C pins
* as general purpose I/O. This will assert CTS and CD for the
* SCC ports.
*/
/* FIXME: see 360um p.7-365 and 860um p.34-12
* I can't make sense of these bits - mleslie*/
/* immap->im_ioport.iop_pcdir |= 0x03c6; */
/* immap->im_ioport.iop_pcpar &= ~0x03c6; */
/* cp->pio_pcdir |= 0x03c6; */
/* cp->pio_pcpar &= ~0x03c6; */
/* Connect SCC2 and SCC3 to NMSI. Connect BRG3 to SCC2 and
* BRG4 to SCC3.
*/
cp->si_sicr &= ~0x00ffff00;
cp->si_sicr |= 0x001b1200;
#ifdef CONFIG_PP04
/* Frequentis PP04 forced to RS-232 until we know better.
* Port C 12 and 13 low enables RS-232 on SCC3 and SCC4.
*/
immap->im_ioport.iop_pcdir |= 0x000c;
immap->im_ioport.iop_pcpar &= ~0x000c;
immap->im_ioport.iop_pcdat &= ~0x000c;
/* This enables the TX driver.
*/
cp->cp_pbpar &= ~0x6000;
cp->cp_pbdat &= ~0x6000;
#endif
for (i = 0, state = rs_table; i < NR_PORTS; i++,state++) {
state->magic = SSTATE_MAGIC;
state->line = i;
state->type = PORT_UNKNOWN;
state->custom_divisor = 0;
state->close_delay = 5*HZ/10;
state->closing_wait = 30*HZ;
state->icount.cts = state->icount.dsr =
state->icount.rng = state->icount.dcd = 0;
state->icount.rx = state->icount.tx = 0;
state->icount.frame = state->icount.parity = 0;
state->icount.overrun = state->icount.brk = 0;
printk(KERN_INFO "ttyS%d at irq 0x%02x is an %s\n",
i, (unsigned int)(state->irq),
(state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC");
#ifdef CONFIG_SERIAL_CONSOLE
/* If we just printed the message on the console port, and
* we are about to initialize it for general use, we have
* to wait a couple of character times for the CR/NL to
* make it out of the transmit buffer.
*/
if (i == CONFIG_SERIAL_CONSOLE_PORT)
mdelay(8);
/* idx = PORT_NUM(info->state->smc_scc_num); */
/* if (info->state->smc_scc_num & NUM_IS_SCC) */
/* chan = scc_chan_map[idx]; */
/* else */
/* chan = smc_chan_map[idx]; */
/* cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG; */
/* while (cp->cp_cr & CPM_CR_FLG); */
#endif
/* info = kmalloc(sizeof(ser_info_t), GFP_KERNEL); */
info = &quicc_ser_info[i];
if (info) {
memset (info, 0, sizeof(ser_info_t));
info->magic = SERIAL_MAGIC;
info->line = i;
info->flags = state->flags;
INIT_WORK(&info->tqueue, do_softint, info);
INIT_WORK(&info->tqueue_hangup, do_serial_hangup, info);
init_waitqueue_head(&info->open_wait);
init_waitqueue_head(&info->close_wait);
info->state = state;
state->info = (struct async_struct *)info;
/* We need to allocate a transmit and receive buffer
* descriptors from dual port ram, and a character
* buffer area from host mem.
*/
dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * RX_NUM_FIFO);
/* Allocate space for FIFOs in the host memory.
* (for now this is from a static array of buffers :(
*/
/* mem_addr = m360_cpm_hostalloc(RX_NUM_FIFO * RX_BUF_SIZE); */
/* mem_addr = kmalloc (RX_NUM_FIFO * RX_BUF_SIZE, GFP_BUFFER); */
mem_addr = &rx_buf_pool[i * RX_NUM_FIFO * RX_BUF_SIZE];
/* Set the physical address of the host memory
* buffers in the buffer descriptors, and the
* virtual address for us to work with.
*/
bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
info->rx_cur = info->rx_bd_base = bdp;
/* initialize rx buffer descriptors */
for (j=0; j<(RX_NUM_FIFO-1); j++) {
bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE];
bdp->status = BD_SC_EMPTY | BD_SC_INTRPT;
mem_addr += RX_BUF_SIZE;
bdp++;
}
bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE];
bdp->status = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT;
idx = PORT_NUM(info->state->smc_scc_num);
if (info->state->smc_scc_num & NUM_IS_SCC) {
#if defined (CONFIG_UCQUICC) && 1
/* set the transceiver mode to RS232 */
sipex_mode_bits &= ~(uint)SIPEX_MODE(idx,0x0f); /* clear current mode */
sipex_mode_bits |= (uint)SIPEX_MODE(idx,0x02);
*(uint *)_periph_base = sipex_mode_bits;
/* printk ("sipex bits = 0x%08x\n", sipex_mode_bits); */
#endif
}
dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * TX_NUM_FIFO);
/* Allocate space for FIFOs in the host memory.
*/
/* mem_addr = m360_cpm_hostalloc(TX_NUM_FIFO * TX_BUF_SIZE); */
/* mem_addr = kmalloc (TX_NUM_FIFO * TX_BUF_SIZE, GFP_BUFFER); */
mem_addr = &tx_buf_pool[i * TX_NUM_FIFO * TX_BUF_SIZE];
/* Set the physical address of the host memory
* buffers in the buffer descriptors, and the
* virtual address for us to work with.
*/
/* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */
bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
info->tx_cur = info->tx_bd_base = (QUICC_BD *)bdp;
/* initialize tx buffer descriptors */
for (j=0; j<(TX_NUM_FIFO-1); j++) {
bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE];
bdp->status = BD_SC_INTRPT;
mem_addr += TX_BUF_SIZE;
bdp++;
}
bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE];
bdp->status = (BD_SC_WRAP | BD_SC_INTRPT);
if (info->state->smc_scc_num & NUM_IS_SCC) {
scp = &pquicc->scc_regs[idx];
sup = &pquicc->pram[info->state->port].scc.pscc.u;
sup->rbase = dp_addr;
sup->tbase = dp_addr;
/* Set up the uart parameters in the
* parameter ram.
*/
sup->rfcr = SMC_EB;
sup->tfcr = SMC_EB;
/* Set this to 1 for now, so we get single
* character interrupts. Using idle character
* time requires some additional tuning.
*/
sup->mrblr = 1;
sup->max_idl = 0;
sup->brkcr = 1;
sup->parec = 0;
sup->frmer = 0;
sup->nosec = 0;
sup->brkec = 0;
sup->uaddr1 = 0;
sup->uaddr2 = 0;
sup->toseq = 0;
{
int i;
for (i=0;i<8;i++)
sup->cc[i] = 0x8000;
}
sup->rccm = 0xc0ff;
/* Send the CPM an initialize command.
*/
chan = scc_chan_map[idx];
/* execute the INIT RX & TX PARAMS command for this channel. */
cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cr & CPM_CR_FLG);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
scp->scc_gsmr.w.high = 0;
scp->scc_gsmr.w.low =
(SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
/* Disable all interrupts and clear all pending
* events.
*/
scp->scc_sccm = 0;
scp->scc_scce = 0xffff;
scp->scc_dsr = 0x7e7e;
scp->scc_psmr = 0x3000;
/* If the port is the console, enable Rx and Tx.
*/
#ifdef CONFIG_SERIAL_CONSOLE
if (i == CONFIG_SERIAL_CONSOLE_PORT)
scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
#endif
}
else {
/* Configure SMCs Tx/Rx instead of port B
* parallel I/O.
*/
up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
up->rbase = dp_addr;
iobits = 0xc0 << (idx * 4);
cp->pip_pbpar |= iobits;
cp->pip_pbdir &= ~iobits;
cp->pip_pbodr &= ~iobits;
/* Connect the baud rate generator to the
* SMC based upon index in rs_table. Also
* make sure it is connected to NMSI.
*/
cp->si_simode &= ~(0xffff << (idx * 16));
cp->si_simode |= (i << ((idx * 16) + 12));
up->tbase = dp_addr;
/* Set up the uart parameters in the
* parameter ram.
*/
up->rfcr = SMC_EB;
up->tfcr = SMC_EB;
/* Set this to 1 for now, so we get single
* character interrupts. Using idle character
* time requires some additional tuning.
*/
up->mrblr = 1;
up->max_idl = 0;
up->brkcr = 1;
/* Send the CPM an initialize command.
*/
chan = smc_chan_map[idx];
cp->cp_cr = mk_cr_cmd(chan,
CPM_CR_INIT_TRX) | CPM_CR_FLG;
#ifdef CONFIG_SERIAL_CONSOLE
if (i == CONFIG_SERIAL_CONSOLE_PORT)
printk("");
#endif
while (cp->cp_cr & CPM_CR_FLG);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
sp = &cp->smc_regs[idx];
sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
/* Disable all interrupts and clear all pending
* events.
*/
sp->smc_smcm = 0;
sp->smc_smce = 0xff;
/* If the port is the console, enable Rx and Tx.
*/
#ifdef CONFIG_SERIAL_CONSOLE
if (i == CONFIG_SERIAL_CONSOLE_PORT)
sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
#endif
}
/* Install interrupt handler.
*/
/* cpm_install_handler(IRQ_MACHSPEC | state->irq, rs_360_interrupt, info); */
/*request_irq(IRQ_MACHSPEC | state->irq, rs_360_interrupt, */
request_irq(state->irq, rs_360_interrupt,
IRQ_FLG_LOCK, "ttyS", (void *)info);
/* Set up the baud rate generator.
*/
m360_cpm_setbrg(i, baud_table[baud_idx]);
}
}
return 0;
}
module_init(rs_360_init);
/* This must always be called before the rs_360_init() function, otherwise
* it blows away the port control information.
*/
//static int __init serial_console_setup( struct console *co, char *options)
int serial_console_setup( struct console *co, char *options)
{
struct serial_state *ser;
uint mem_addr, dp_addr, bidx, idx, iobits;
ushort chan;
QUICC_BD *bdp;
volatile QUICC *cp;
volatile struct smc_regs *sp;
volatile struct scc_regs *scp;
volatile struct smc_uart_pram *up;
volatile struct uart_pram *sup;
/* mleslie TODO:
* add something to the 68k bootloader to store a desired initial console baud rate */
/* bd_t *bd; */ /* a board info struct used by EPPC-bug */
/* bd = (bd_t *)__res; */
for (bidx = 0; bidx < (sizeof(baud_table) / sizeof(int)); bidx++)
/* if (bd->bi_baudrate == baud_table[bidx]) */
if (CONSOLE_BAUDRATE == baud_table[bidx])
break;
/* co->cflag = CREAD|CLOCAL|bidx|CS8; */
baud_idx = bidx;
ser = rs_table + CONFIG_SERIAL_CONSOLE_PORT;
cp = pquicc; /* Get pointer to Communication Processor */
idx = PORT_NUM(ser->smc_scc_num);
if (ser->smc_scc_num & NUM_IS_SCC) {
/* TODO: need to set up SCC pin assignment etc. here */
}
else {
iobits = 0xc0 << (idx * 4);
cp->pip_pbpar |= iobits;
cp->pip_pbdir &= ~iobits;
cp->pip_pbodr &= ~iobits;
/* Connect the baud rate generator to the
* SMC based upon index in rs_table. Also
* make sure it is connected to NMSI.
*/
cp->si_simode &= ~(0xffff << (idx * 16));
cp->si_simode |= (idx << ((idx * 16) + 12));
}
/* When we get here, the CPM has been reset, so we need
* to configure the port.
* We need to allocate a transmit and receive buffer descriptor
* from dual port ram, and a character buffer area from host mem.
*/
/* Allocate space for two buffer descriptors in the DP ram.
*/
dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * CONSOLE_NUM_FIFO);
/* Allocate space for two 2 byte FIFOs in the host memory.
*/
/* mem_addr = m360_cpm_hostalloc(8); */
mem_addr = (uint)console_fifos;
/* Set the physical address of the host memory buffers in
* the buffer descriptors.
*/
/* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */
bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
bdp->buf = (char *)mem_addr;
(bdp+1)->buf = (char *)(mem_addr+4);
/* For the receive, set empty and wrap.
* For transmit, set wrap.
*/
bdp->status = BD_SC_EMPTY | BD_SC_WRAP;
(bdp+1)->status = BD_SC_WRAP;
/* Set up the uart parameters in the parameter ram.
*/
if (ser->smc_scc_num & NUM_IS_SCC) {
scp = &cp->scc_regs[idx];
/* sup = (scc_uart_t *)&cp->cp_dparam[ser->port]; */
sup = &pquicc->pram[ser->port].scc.pscc.u;
sup->rbase = dp_addr;
sup->tbase = dp_addr + sizeof(QUICC_BD);
/* Set up the uart parameters in the
* parameter ram.
*/
sup->rfcr = SMC_EB;
sup->tfcr = SMC_EB;
/* Set this to 1 for now, so we get single
* character interrupts. Using idle character
* time requires some additional tuning.
*/
sup->mrblr = 1;
sup->max_idl = 0;
sup->brkcr = 1;
sup->parec = 0;
sup->frmer = 0;
sup->nosec = 0;
sup->brkec = 0;
sup->uaddr1 = 0;
sup->uaddr2 = 0;
sup->toseq = 0;
{
int i;
for (i=0;i<8;i++)
sup->cc[i] = 0x8000;
}
sup->rccm = 0xc0ff;
/* Send the CPM an initialize command.
*/
chan = scc_chan_map[idx];
cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cr & CPM_CR_FLG);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
scp->scc_gsmr.w.high = 0;
scp->scc_gsmr.w.low =
(SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
/* Disable all interrupts and clear all pending
* events.
*/
scp->scc_sccm = 0;
scp->scc_scce = 0xffff;
scp->scc_dsr = 0x7e7e;
scp->scc_psmr = 0x3000;
scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
else {
/* up = (smc_uart_t *)&cp->cp_dparam[ser->port]; */
up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u;
up->rbase = dp_addr; /* Base of receive buffer desc. */
up->tbase = dp_addr+sizeof(QUICC_BD); /* Base of xmt buffer desc. */
up->rfcr = SMC_EB;
up->tfcr = SMC_EB;
/* Set this to 1 for now, so we get single character interrupts.
*/
up->mrblr = 1; /* receive buffer length */
up->max_idl = 0; /* wait forever for next char */
/* Send the CPM an initialize command.
*/
chan = smc_chan_map[idx];
cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cr & CPM_CR_FLG);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
sp = &cp->smc_regs[idx];
sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
/* And finally, enable Rx and Tx.
*/
sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
}
/* Set up the baud rate generator.
*/
/* m360_cpm_setbrg((ser - rs_table), bd->bi_baudrate); */
m360_cpm_setbrg((ser - rs_table), CONSOLE_BAUDRATE);
return 0;
}
/*
* Local variables:
* c-indent-level: 4
* c-basic-offset: 4
* tab-width: 4
* End:
*/