| static int prism2_enable_aux_port(struct net_device *dev, int enable) |
| { |
| u16 val, reg; |
| int i, tries; |
| unsigned long flags; |
| struct hostap_interface *iface; |
| local_info_t *local; |
| |
| iface = netdev_priv(dev); |
| local = iface->local; |
| |
| if (local->no_pri) { |
| if (enable) { |
| PDEBUG(DEBUG_EXTRA2, "%s: no PRI f/w - assuming Aux " |
| "port is already enabled\n", dev->name); |
| } |
| return 0; |
| } |
| |
| spin_lock_irqsave(&local->cmdlock, flags); |
| |
| /* wait until busy bit is clear */ |
| tries = HFA384X_CMD_BUSY_TIMEOUT; |
| while (HFA384X_INW(HFA384X_CMD_OFF) & HFA384X_CMD_BUSY && tries > 0) { |
| tries--; |
| udelay(1); |
| } |
| if (tries == 0) { |
| reg = HFA384X_INW(HFA384X_CMD_OFF); |
| spin_unlock_irqrestore(&local->cmdlock, flags); |
| printk("%s: prism2_enable_aux_port - timeout - reg=0x%04x\n", |
| dev->name, reg); |
| return -ETIMEDOUT; |
| } |
| |
| val = HFA384X_INW(HFA384X_CONTROL_OFF); |
| |
| if (enable) { |
| HFA384X_OUTW(HFA384X_AUX_MAGIC0, HFA384X_PARAM0_OFF); |
| HFA384X_OUTW(HFA384X_AUX_MAGIC1, HFA384X_PARAM1_OFF); |
| HFA384X_OUTW(HFA384X_AUX_MAGIC2, HFA384X_PARAM2_OFF); |
| |
| if ((val & HFA384X_AUX_PORT_MASK) != HFA384X_AUX_PORT_DISABLED) |
| printk("prism2_enable_aux_port: was not disabled!?\n"); |
| val &= ~HFA384X_AUX_PORT_MASK; |
| val |= HFA384X_AUX_PORT_ENABLE; |
| } else { |
| HFA384X_OUTW(0, HFA384X_PARAM0_OFF); |
| HFA384X_OUTW(0, HFA384X_PARAM1_OFF); |
| HFA384X_OUTW(0, HFA384X_PARAM2_OFF); |
| |
| if ((val & HFA384X_AUX_PORT_MASK) != HFA384X_AUX_PORT_ENABLED) |
| printk("prism2_enable_aux_port: was not enabled!?\n"); |
| val &= ~HFA384X_AUX_PORT_MASK; |
| val |= HFA384X_AUX_PORT_DISABLE; |
| } |
| HFA384X_OUTW(val, HFA384X_CONTROL_OFF); |
| |
| udelay(5); |
| |
| i = 10000; |
| while (i > 0) { |
| val = HFA384X_INW(HFA384X_CONTROL_OFF); |
| val &= HFA384X_AUX_PORT_MASK; |
| |
| if ((enable && val == HFA384X_AUX_PORT_ENABLED) || |
| (!enable && val == HFA384X_AUX_PORT_DISABLED)) |
| break; |
| |
| udelay(10); |
| i--; |
| } |
| |
| spin_unlock_irqrestore(&local->cmdlock, flags); |
| |
| if (i == 0) { |
| printk("prism2_enable_aux_port(%d) timed out\n", |
| enable); |
| return -ETIMEDOUT; |
| } |
| |
| return 0; |
| } |
| |
| |
| static int hfa384x_from_aux(struct net_device *dev, unsigned int addr, int len, |
| void *buf) |
| { |
| u16 page, offset; |
| if (addr & 1 || len & 1) |
| return -1; |
| |
| page = addr >> 7; |
| offset = addr & 0x7f; |
| |
| HFA384X_OUTW(page, HFA384X_AUXPAGE_OFF); |
| HFA384X_OUTW(offset, HFA384X_AUXOFFSET_OFF); |
| |
| udelay(5); |
| |
| #ifdef PRISM2_PCI |
| { |
| u16 *pos = (u16 *) buf; |
| while (len > 0) { |
| *pos++ = HFA384X_INW_DATA(HFA384X_AUXDATA_OFF); |
| len -= 2; |
| } |
| } |
| #else /* PRISM2_PCI */ |
| HFA384X_INSW(HFA384X_AUXDATA_OFF, buf, len / 2); |
| #endif /* PRISM2_PCI */ |
| |
| return 0; |
| } |
| |
| |
| static int hfa384x_to_aux(struct net_device *dev, unsigned int addr, int len, |
| void *buf) |
| { |
| u16 page, offset; |
| if (addr & 1 || len & 1) |
| return -1; |
| |
| page = addr >> 7; |
| offset = addr & 0x7f; |
| |
| HFA384X_OUTW(page, HFA384X_AUXPAGE_OFF); |
| HFA384X_OUTW(offset, HFA384X_AUXOFFSET_OFF); |
| |
| udelay(5); |
| |
| #ifdef PRISM2_PCI |
| { |
| u16 *pos = (u16 *) buf; |
| while (len > 0) { |
| HFA384X_OUTW_DATA(*pos++, HFA384X_AUXDATA_OFF); |
| len -= 2; |
| } |
| } |
| #else /* PRISM2_PCI */ |
| HFA384X_OUTSW(HFA384X_AUXDATA_OFF, buf, len / 2); |
| #endif /* PRISM2_PCI */ |
| |
| return 0; |
| } |
| |
| |
| static int prism2_pda_ok(u8 *buf) |
| { |
| u16 *pda = (u16 *) buf; |
| int pos; |
| u16 len, pdr; |
| |
| if (buf[0] == 0xff && buf[1] == 0x00 && buf[2] == 0xff && |
| buf[3] == 0x00) |
| return 0; |
| |
| pos = 0; |
| while (pos + 1 < PRISM2_PDA_SIZE / 2) { |
| len = le16_to_cpu(pda[pos]); |
| pdr = le16_to_cpu(pda[pos + 1]); |
| if (len == 0 || pos + len > PRISM2_PDA_SIZE / 2) |
| return 0; |
| |
| if (pdr == 0x0000 && len == 2) { |
| /* PDA end found */ |
| return 1; |
| } |
| |
| pos += len + 1; |
| } |
| |
| return 0; |
| } |
| |
| |
| static int prism2_download_aux_dump(struct net_device *dev, |
| unsigned int addr, int len, u8 *buf) |
| { |
| int res; |
| |
| prism2_enable_aux_port(dev, 1); |
| res = hfa384x_from_aux(dev, addr, len, buf); |
| prism2_enable_aux_port(dev, 0); |
| if (res) |
| return -1; |
| |
| return 0; |
| } |
| |
| |
| static u8 * prism2_read_pda(struct net_device *dev) |
| { |
| u8 *buf; |
| int res, i, found = 0; |
| #define NUM_PDA_ADDRS 4 |
| unsigned int pda_addr[NUM_PDA_ADDRS] = { |
| 0x7f0000 /* others than HFA3841 */, |
| 0x3f0000 /* HFA3841 */, |
| 0x390000 /* apparently used in older cards */, |
| 0x7f0002 /* Intel PRO/Wireless 2011B (PCI) */, |
| }; |
| |
| buf = (u8 *) kmalloc(PRISM2_PDA_SIZE, GFP_KERNEL); |
| if (buf == NULL) |
| return NULL; |
| |
| /* Note: wlan card should be in initial state (just after init cmd) |
| * and no other operations should be performed concurrently. */ |
| |
| prism2_enable_aux_port(dev, 1); |
| |
| for (i = 0; i < NUM_PDA_ADDRS; i++) { |
| PDEBUG(DEBUG_EXTRA2, "%s: trying to read PDA from 0x%08x", |
| dev->name, pda_addr[i]); |
| res = hfa384x_from_aux(dev, pda_addr[i], PRISM2_PDA_SIZE, buf); |
| if (res) |
| continue; |
| if (res == 0 && prism2_pda_ok(buf)) { |
| PDEBUG2(DEBUG_EXTRA2, ": OK\n"); |
| found = 1; |
| break; |
| } else { |
| PDEBUG2(DEBUG_EXTRA2, ": failed\n"); |
| } |
| } |
| |
| prism2_enable_aux_port(dev, 0); |
| |
| if (!found) { |
| printk(KERN_DEBUG "%s: valid PDA not found\n", dev->name); |
| kfree(buf); |
| buf = NULL; |
| } |
| |
| return buf; |
| } |
| |
| |
| static int prism2_download_volatile(local_info_t *local, |
| struct prism2_download_data *param) |
| { |
| struct net_device *dev = local->dev; |
| int ret = 0, i; |
| u16 param0, param1; |
| |
| if (local->hw_downloading) { |
| printk(KERN_WARNING "%s: Already downloading - aborting new " |
| "request\n", dev->name); |
| return -1; |
| } |
| |
| local->hw_downloading = 1; |
| if (local->pri_only) { |
| hfa384x_disable_interrupts(dev); |
| } else { |
| prism2_hw_shutdown(dev, 0); |
| |
| if (prism2_hw_init(dev, 0)) { |
| printk(KERN_WARNING "%s: Could not initialize card for" |
| " download\n", dev->name); |
| ret = -1; |
| goto out; |
| } |
| } |
| |
| if (prism2_enable_aux_port(dev, 1)) { |
| printk(KERN_WARNING "%s: Could not enable AUX port\n", |
| dev->name); |
| ret = -1; |
| goto out; |
| } |
| |
| param0 = param->start_addr & 0xffff; |
| param1 = param->start_addr >> 16; |
| |
| HFA384X_OUTW(0, HFA384X_PARAM2_OFF); |
| HFA384X_OUTW(param1, HFA384X_PARAM1_OFF); |
| if (hfa384x_cmd_wait(dev, HFA384X_CMDCODE_DOWNLOAD | |
| (HFA384X_PROGMODE_ENABLE_VOLATILE << 8), |
| param0)) { |
| printk(KERN_WARNING "%s: Download command execution failed\n", |
| dev->name); |
| ret = -1; |
| goto out; |
| } |
| |
| for (i = 0; i < param->num_areas; i++) { |
| PDEBUG(DEBUG_EXTRA2, "%s: Writing %d bytes at 0x%08x\n", |
| dev->name, param->data[i].len, param->data[i].addr); |
| if (hfa384x_to_aux(dev, param->data[i].addr, |
| param->data[i].len, param->data[i].data)) { |
| printk(KERN_WARNING "%s: RAM download at 0x%08x " |
| "(len=%d) failed\n", dev->name, |
| param->data[i].addr, param->data[i].len); |
| ret = -1; |
| goto out; |
| } |
| } |
| |
| HFA384X_OUTW(param1, HFA384X_PARAM1_OFF); |
| HFA384X_OUTW(0, HFA384X_PARAM2_OFF); |
| if (hfa384x_cmd_no_wait(dev, HFA384X_CMDCODE_DOWNLOAD | |
| (HFA384X_PROGMODE_DISABLE << 8), param0)) { |
| printk(KERN_WARNING "%s: Download command execution failed\n", |
| dev->name); |
| ret = -1; |
| goto out; |
| } |
| /* ProgMode disable causes the hardware to restart itself from the |
| * given starting address. Give hw some time and ACK command just in |
| * case restart did not happen. */ |
| mdelay(5); |
| HFA384X_OUTW(HFA384X_EV_CMD, HFA384X_EVACK_OFF); |
| |
| if (prism2_enable_aux_port(dev, 0)) { |
| printk(KERN_DEBUG "%s: Disabling AUX port failed\n", |
| dev->name); |
| /* continue anyway.. restart should have taken care of this */ |
| } |
| |
| mdelay(5); |
| local->hw_downloading = 0; |
| if (prism2_hw_config(dev, 2)) { |
| printk(KERN_WARNING "%s: Card configuration after RAM " |
| "download failed\n", dev->name); |
| ret = -1; |
| goto out; |
| } |
| |
| out: |
| local->hw_downloading = 0; |
| return ret; |
| } |
| |
| |
| static int prism2_enable_genesis(local_info_t *local, int hcr) |
| { |
| struct net_device *dev = local->dev; |
| u8 initseq[4] = { 0x00, 0xe1, 0xa1, 0xff }; |
| u8 readbuf[4]; |
| |
| printk(KERN_DEBUG "%s: test Genesis mode with HCR 0x%02x\n", |
| dev->name, hcr); |
| local->func->cor_sreset(local); |
| hfa384x_to_aux(dev, 0x7e0038, sizeof(initseq), initseq); |
| local->func->genesis_reset(local, hcr); |
| |
| /* Readback test */ |
| hfa384x_from_aux(dev, 0x7e0038, sizeof(readbuf), readbuf); |
| hfa384x_to_aux(dev, 0x7e0038, sizeof(initseq), initseq); |
| hfa384x_from_aux(dev, 0x7e0038, sizeof(readbuf), readbuf); |
| |
| if (memcmp(initseq, readbuf, sizeof(initseq)) == 0) { |
| printk(KERN_DEBUG "Readback test succeeded, HCR 0x%02x\n", |
| hcr); |
| return 0; |
| } else { |
| printk(KERN_DEBUG "Readback test failed, HCR 0x%02x " |
| "write %02x %02x %02x %02x read %02x %02x %02x %02x\n", |
| hcr, initseq[0], initseq[1], initseq[2], initseq[3], |
| readbuf[0], readbuf[1], readbuf[2], readbuf[3]); |
| return 1; |
| } |
| } |
| |
| |
| static int prism2_get_ram_size(local_info_t *local) |
| { |
| int ret; |
| |
| /* Try to enable genesis mode; 0x1F for x8 SRAM or 0x0F for x16 SRAM */ |
| if (prism2_enable_genesis(local, 0x1f) == 0) |
| ret = 8; |
| else if (prism2_enable_genesis(local, 0x0f) == 0) |
| ret = 16; |
| else |
| ret = -1; |
| |
| /* Disable genesis mode */ |
| local->func->genesis_reset(local, ret == 16 ? 0x07 : 0x17); |
| |
| return ret; |
| } |
| |
| |
| static int prism2_download_genesis(local_info_t *local, |
| struct prism2_download_data *param) |
| { |
| struct net_device *dev = local->dev; |
| int ram16 = 0, i; |
| int ret = 0; |
| |
| if (local->hw_downloading) { |
| printk(KERN_WARNING "%s: Already downloading - aborting new " |
| "request\n", dev->name); |
| return -EBUSY; |
| } |
| |
| if (!local->func->genesis_reset || !local->func->cor_sreset) { |
| printk(KERN_INFO "%s: Genesis mode downloading not supported " |
| "with this hwmodel\n", dev->name); |
| return -EOPNOTSUPP; |
| } |
| |
| local->hw_downloading = 1; |
| |
| if (prism2_enable_aux_port(dev, 1)) { |
| printk(KERN_DEBUG "%s: failed to enable AUX port\n", |
| dev->name); |
| ret = -EIO; |
| goto out; |
| } |
| |
| if (local->sram_type == -1) { |
| /* 0x1F for x8 SRAM or 0x0F for x16 SRAM */ |
| if (prism2_enable_genesis(local, 0x1f) == 0) { |
| ram16 = 0; |
| PDEBUG(DEBUG_EXTRA2, "%s: Genesis mode OK using x8 " |
| "SRAM\n", dev->name); |
| } else if (prism2_enable_genesis(local, 0x0f) == 0) { |
| ram16 = 1; |
| PDEBUG(DEBUG_EXTRA2, "%s: Genesis mode OK using x16 " |
| "SRAM\n", dev->name); |
| } else { |
| printk(KERN_DEBUG "%s: Could not initiate genesis " |
| "mode\n", dev->name); |
| ret = -EIO; |
| goto out; |
| } |
| } else { |
| if (prism2_enable_genesis(local, local->sram_type == 8 ? |
| 0x1f : 0x0f)) { |
| printk(KERN_DEBUG "%s: Failed to set Genesis " |
| "mode (sram_type=%d)\n", dev->name, |
| local->sram_type); |
| ret = -EIO; |
| goto out; |
| } |
| ram16 = local->sram_type != 8; |
| } |
| |
| for (i = 0; i < param->num_areas; i++) { |
| PDEBUG(DEBUG_EXTRA2, "%s: Writing %d bytes at 0x%08x\n", |
| dev->name, param->data[i].len, param->data[i].addr); |
| if (hfa384x_to_aux(dev, param->data[i].addr, |
| param->data[i].len, param->data[i].data)) { |
| printk(KERN_WARNING "%s: RAM download at 0x%08x " |
| "(len=%d) failed\n", dev->name, |
| param->data[i].addr, param->data[i].len); |
| ret = -EIO; |
| goto out; |
| } |
| } |
| |
| PDEBUG(DEBUG_EXTRA2, "Disable genesis mode\n"); |
| local->func->genesis_reset(local, ram16 ? 0x07 : 0x17); |
| if (prism2_enable_aux_port(dev, 0)) { |
| printk(KERN_DEBUG "%s: Failed to disable AUX port\n", |
| dev->name); |
| } |
| |
| mdelay(5); |
| local->hw_downloading = 0; |
| |
| PDEBUG(DEBUG_EXTRA2, "Trying to initialize card\n"); |
| /* |
| * Make sure the INIT command does not generate a command completion |
| * event by disabling interrupts. |
| */ |
| hfa384x_disable_interrupts(dev); |
| if (prism2_hw_init(dev, 1)) { |
| printk(KERN_DEBUG "%s: Initialization after genesis mode " |
| "download failed\n", dev->name); |
| ret = -EIO; |
| goto out; |
| } |
| |
| PDEBUG(DEBUG_EXTRA2, "Card initialized - running PRI only\n"); |
| if (prism2_hw_init2(dev, 1)) { |
| printk(KERN_DEBUG "%s: Initialization(2) after genesis mode " |
| "download failed\n", dev->name); |
| ret = -EIO; |
| goto out; |
| } |
| |
| out: |
| local->hw_downloading = 0; |
| return ret; |
| } |
| |
| |
| #ifdef PRISM2_NON_VOLATILE_DOWNLOAD |
| /* Note! Non-volatile downloading functionality has not yet been tested |
| * thoroughly and it may corrupt flash image and effectively kill the card that |
| * is being updated. You have been warned. */ |
| |
| static inline int prism2_download_block(struct net_device *dev, |
| u32 addr, u8 *data, |
| u32 bufaddr, int rest_len) |
| { |
| u16 param0, param1; |
| int block_len; |
| |
| block_len = rest_len < 4096 ? rest_len : 4096; |
| |
| param0 = addr & 0xffff; |
| param1 = addr >> 16; |
| |
| HFA384X_OUTW(block_len, HFA384X_PARAM2_OFF); |
| HFA384X_OUTW(param1, HFA384X_PARAM1_OFF); |
| |
| if (hfa384x_cmd_wait(dev, HFA384X_CMDCODE_DOWNLOAD | |
| (HFA384X_PROGMODE_ENABLE_NON_VOLATILE << 8), |
| param0)) { |
| printk(KERN_WARNING "%s: Flash download command execution " |
| "failed\n", dev->name); |
| return -1; |
| } |
| |
| if (hfa384x_to_aux(dev, bufaddr, block_len, data)) { |
| printk(KERN_WARNING "%s: flash download at 0x%08x " |
| "(len=%d) failed\n", dev->name, addr, block_len); |
| return -1; |
| } |
| |
| HFA384X_OUTW(0, HFA384X_PARAM2_OFF); |
| HFA384X_OUTW(0, HFA384X_PARAM1_OFF); |
| if (hfa384x_cmd_wait(dev, HFA384X_CMDCODE_DOWNLOAD | |
| (HFA384X_PROGMODE_PROGRAM_NON_VOLATILE << 8), |
| 0)) { |
| printk(KERN_WARNING "%s: Flash write command execution " |
| "failed\n", dev->name); |
| return -1; |
| } |
| |
| return block_len; |
| } |
| |
| |
| static int prism2_download_nonvolatile(local_info_t *local, |
| struct prism2_download_data *dl) |
| { |
| struct net_device *dev = local->dev; |
| int ret = 0, i; |
| struct { |
| u16 page; |
| u16 offset; |
| u16 len; |
| } dlbuffer; |
| u32 bufaddr; |
| |
| if (local->hw_downloading) { |
| printk(KERN_WARNING "%s: Already downloading - aborting new " |
| "request\n", dev->name); |
| return -1; |
| } |
| |
| ret = local->func->get_rid(dev, HFA384X_RID_DOWNLOADBUFFER, |
| &dlbuffer, 6, 0); |
| |
| if (ret < 0) { |
| printk(KERN_WARNING "%s: Could not read download buffer " |
| "parameters\n", dev->name); |
| goto out; |
| } |
| |
| dlbuffer.page = le16_to_cpu(dlbuffer.page); |
| dlbuffer.offset = le16_to_cpu(dlbuffer.offset); |
| dlbuffer.len = le16_to_cpu(dlbuffer.len); |
| |
| printk(KERN_DEBUG "Download buffer: %d bytes at 0x%04x:0x%04x\n", |
| dlbuffer.len, dlbuffer.page, dlbuffer.offset); |
| |
| bufaddr = (dlbuffer.page << 7) + dlbuffer.offset; |
| |
| local->hw_downloading = 1; |
| |
| if (!local->pri_only) { |
| prism2_hw_shutdown(dev, 0); |
| |
| if (prism2_hw_init(dev, 0)) { |
| printk(KERN_WARNING "%s: Could not initialize card for" |
| " download\n", dev->name); |
| ret = -1; |
| goto out; |
| } |
| } |
| |
| hfa384x_disable_interrupts(dev); |
| |
| if (prism2_enable_aux_port(dev, 1)) { |
| printk(KERN_WARNING "%s: Could not enable AUX port\n", |
| dev->name); |
| ret = -1; |
| goto out; |
| } |
| |
| printk(KERN_DEBUG "%s: starting flash download\n", dev->name); |
| for (i = 0; i < dl->num_areas; i++) { |
| int rest_len = dl->data[i].len; |
| int data_off = 0; |
| |
| while (rest_len > 0) { |
| int block_len; |
| |
| block_len = prism2_download_block( |
| dev, dl->data[i].addr + data_off, |
| dl->data[i].data + data_off, bufaddr, |
| rest_len); |
| |
| if (block_len < 0) { |
| ret = -1; |
| goto out; |
| } |
| |
| rest_len -= block_len; |
| data_off += block_len; |
| } |
| } |
| |
| HFA384X_OUTW(0, HFA384X_PARAM1_OFF); |
| HFA384X_OUTW(0, HFA384X_PARAM2_OFF); |
| if (hfa384x_cmd_wait(dev, HFA384X_CMDCODE_DOWNLOAD | |
| (HFA384X_PROGMODE_DISABLE << 8), 0)) { |
| printk(KERN_WARNING "%s: Download command execution failed\n", |
| dev->name); |
| ret = -1; |
| goto out; |
| } |
| |
| if (prism2_enable_aux_port(dev, 0)) { |
| printk(KERN_DEBUG "%s: Disabling AUX port failed\n", |
| dev->name); |
| /* continue anyway.. restart should have taken care of this */ |
| } |
| |
| mdelay(5); |
| |
| local->func->hw_reset(dev); |
| local->hw_downloading = 0; |
| if (prism2_hw_config(dev, 2)) { |
| printk(KERN_WARNING "%s: Card configuration after flash " |
| "download failed\n", dev->name); |
| ret = -1; |
| } else { |
| printk(KERN_INFO "%s: Card initialized successfully after " |
| "flash download\n", dev->name); |
| } |
| |
| out: |
| local->hw_downloading = 0; |
| return ret; |
| } |
| #endif /* PRISM2_NON_VOLATILE_DOWNLOAD */ |
| |
| |
| static void prism2_download_free_data(struct prism2_download_data *dl) |
| { |
| int i; |
| |
| if (dl == NULL) |
| return; |
| |
| for (i = 0; i < dl->num_areas; i++) |
| kfree(dl->data[i].data); |
| kfree(dl); |
| } |
| |
| |
| static int prism2_download(local_info_t *local, |
| struct prism2_download_param *param) |
| { |
| int ret = 0; |
| int i; |
| u32 total_len = 0; |
| struct prism2_download_data *dl = NULL; |
| |
| printk(KERN_DEBUG "prism2_download: dl_cmd=%d start_addr=0x%08x " |
| "num_areas=%d\n", |
| param->dl_cmd, param->start_addr, param->num_areas); |
| |
| if (param->num_areas > 100) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| dl = kmalloc(sizeof(*dl) + param->num_areas * |
| sizeof(struct prism2_download_data_area), GFP_KERNEL); |
| if (dl == NULL) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| memset(dl, 0, sizeof(*dl) + param->num_areas * |
| sizeof(struct prism2_download_data_area)); |
| dl->dl_cmd = param->dl_cmd; |
| dl->start_addr = param->start_addr; |
| dl->num_areas = param->num_areas; |
| for (i = 0; i < param->num_areas; i++) { |
| PDEBUG(DEBUG_EXTRA2, |
| " area %d: addr=0x%08x len=%d ptr=0x%p\n", |
| i, param->data[i].addr, param->data[i].len, |
| param->data[i].ptr); |
| |
| dl->data[i].addr = param->data[i].addr; |
| dl->data[i].len = param->data[i].len; |
| |
| total_len += param->data[i].len; |
| if (param->data[i].len > PRISM2_MAX_DOWNLOAD_AREA_LEN || |
| total_len > PRISM2_MAX_DOWNLOAD_LEN) { |
| ret = -E2BIG; |
| goto out; |
| } |
| |
| dl->data[i].data = kmalloc(dl->data[i].len, GFP_KERNEL); |
| if (dl->data[i].data == NULL) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| if (copy_from_user(dl->data[i].data, param->data[i].ptr, |
| param->data[i].len)) { |
| ret = -EFAULT; |
| goto out; |
| } |
| } |
| |
| switch (param->dl_cmd) { |
| case PRISM2_DOWNLOAD_VOLATILE: |
| case PRISM2_DOWNLOAD_VOLATILE_PERSISTENT: |
| ret = prism2_download_volatile(local, dl); |
| break; |
| case PRISM2_DOWNLOAD_VOLATILE_GENESIS: |
| case PRISM2_DOWNLOAD_VOLATILE_GENESIS_PERSISTENT: |
| ret = prism2_download_genesis(local, dl); |
| break; |
| case PRISM2_DOWNLOAD_NON_VOLATILE: |
| #ifdef PRISM2_NON_VOLATILE_DOWNLOAD |
| ret = prism2_download_nonvolatile(local, dl); |
| #else /* PRISM2_NON_VOLATILE_DOWNLOAD */ |
| printk(KERN_INFO "%s: non-volatile downloading not enabled\n", |
| local->dev->name); |
| ret = -EOPNOTSUPP; |
| #endif /* PRISM2_NON_VOLATILE_DOWNLOAD */ |
| break; |
| default: |
| printk(KERN_DEBUG "%s: unsupported download command %d\n", |
| local->dev->name, param->dl_cmd); |
| ret = -EINVAL; |
| break; |
| }; |
| |
| out: |
| if (ret == 0 && dl && |
| param->dl_cmd == PRISM2_DOWNLOAD_VOLATILE_GENESIS_PERSISTENT) { |
| prism2_download_free_data(local->dl_pri); |
| local->dl_pri = dl; |
| } else if (ret == 0 && dl && |
| param->dl_cmd == PRISM2_DOWNLOAD_VOLATILE_PERSISTENT) { |
| prism2_download_free_data(local->dl_sec); |
| local->dl_sec = dl; |
| } else |
| prism2_download_free_data(dl); |
| |
| return ret; |
| } |