| /* |
| * include/asm-arm/arch-pxa/pcm990_baseboard.h |
| * |
| * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> |
| * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| */ |
| |
| #include <asm/arch/pcm027.h> |
| |
| /* |
| * definitions relevant only when the PCM-990 |
| * development base board is in use |
| */ |
| |
| /* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */ |
| #define PCM990_CTRL_INT_IRQ_GPIO 9 |
| #define PCM990_CTRL_INT_IRQ IRQ_GPIO(PCM990_CTRL_INT_IRQ_GPIO) |
| #define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| #define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */ |
| #define PCM990_CTRL_BASE 0xea000000 |
| #define PCM990_CTRL_SIZE (1*1024*1024) |
| |
| #define PCM990_CTRL_PWR_IRQ_GPIO 14 |
| #define PCM990_CTRL_PWR_IRQ IRQ_GPIO(PCM990_CTRL_PWR_IRQ_GPIO) |
| #define PCM990_CTRL_PWR_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| |
| /* visible CPLD (U7) registers */ |
| #define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */ |
| #define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */ |
| #define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */ |
| #define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */ |
| |
| #define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */ |
| #define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */ |
| #define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */ |
| #define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */ |
| |
| #define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */ |
| #define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */ |
| #define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */ |
| #define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */ |
| |
| #define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */ |
| #define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */ |
| #define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */ |
| #define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */ |
| #define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */ |
| |
| #define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */ |
| #define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */ |
| |
| #define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */ |
| #define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */ |
| #define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */ |
| #define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */ |
| #define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */ |
| |
| #define PCM990_CTRL_REG6 0x000C /* Interrupt Clear REGISTER */ |
| #define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */ |
| #define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */ |
| #define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */ |
| #define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */ |
| |
| #define PCM990_CTRL_REG7 0x000E /* Interrupt Enable REGISTER */ |
| #define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */ |
| #define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */ |
| #define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */ |
| #define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */ |
| |
| #define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */ |
| #define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */ |
| #define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */ |
| #define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */ |
| #define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */ |
| |
| #define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */ |
| #define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */ |
| #define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */ |
| #define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */ |
| |
| #define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */ |
| #define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */ |
| #define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */ |
| |
| #define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */ |
| #define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */ |
| #define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */ |
| #define PCM990_CTRL_ACPRES 0x0004 /* DC Present */ |
| #define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */ |
| |
| #define PCM990_CTRL_P2V(x) ((x) - PCM990_CTRL_PHYS + PCM990_CTRL_BASE) |
| #define PCM990_CTRL_V2P(x) ((x) - PCM990_CTRL_BASE + PCM990_CTRL_PHYS) |
| |
| #ifndef __ASSEMBLY__ |
| # define __PCM990_CTRL_REG(x) \ |
| (*((volatile unsigned char *)PCM990_CTRL_P2V(x))) |
| #else |
| # define __PCM990_CTRL_REG(x) PCM990_CTRL_P2V(x) |
| #endif |
| |
| #define PCM990_INTMSKENA __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7) |
| #define PCM990_INTSETCLR __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6) |
| #define PCM990_CTRL0 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG0) |
| #define PCM990_CTRL1 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG1) |
| #define PCM990_CTRL2 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG2) |
| #define PCM990_CTRL3 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) |
| #define PCM990_CTRL4 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG4) |
| #define PCM990_CTRL5 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) |
| #define PCM990_CTRL6 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6) |
| #define PCM990_CTRL7 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7) |
| #define PCM990_CTRL8 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG8) |
| #define PCM990_CTRL9 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG9) |
| #define PCM990_CTRL10 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG10) |
| #define PCM990_CTRL11 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG11) |
| |
| |
| /* |
| * IDE |
| */ |
| #define PCM990_IDE_IRQ_GPIO 13 |
| #define PCM990_IDE_IRQ IRQ_GPIO(PCM990_IDE_IRQ_GPIO) |
| #define PCM990_IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| #define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */ |
| #define PCM990_IDE_PLD_BASE 0xee000000 |
| #define PCM990_IDE_PLD_SIZE (1*1024*1024) |
| |
| /* visible CPLD (U6) registers */ |
| #define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */ |
| #define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */ |
| #define PCM990_IDE_STBY 0x0008 /* R System StandBy */ |
| |
| #define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */ |
| #define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */ |
| #define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */ |
| #define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */ |
| |
| #define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */ |
| #define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */ |
| #define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */ |
| #define PCM990_IDE_RDY 0x0008 /* RDY */ |
| |
| #define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */ |
| #define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */ |
| #define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */ |
| #define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */ |
| |
| #define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */ |
| #define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */ |
| #define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */ |
| #define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */ |
| |
| #define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE) |
| #define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS) |
| |
| #ifndef __ASSEMBLY__ |
| # define __PCM990_IDE_PLD_REG(x) \ |
| (*((volatile unsigned char *)PCM990_IDE_PLD_P2V(x))) |
| #else |
| # define __PCM990_IDE_PLD_REG(x) PCM990_IDE_PLD_P2V(x) |
| #endif |
| |
| #define PCM990_IDE0 \ |
| __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG0) |
| #define PCM990_IDE1 \ |
| __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG1) |
| #define PCM990_IDE2 \ |
| __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG2) |
| #define PCM990_IDE3 \ |
| __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG3) |
| #define PCM990_IDE4 \ |
| __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG4) |
| |
| /* |
| * Compact Flash |
| */ |
| #define PCM990_CF_IRQ_GPIO 11 |
| #define PCM990_CF_IRQ IRQ_GPIO(PCM990_CF_IRQ_GPIO) |
| #define PCM990_CF_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| |
| #define PCM990_CF_CD_GPIO 12 |
| #define PCM990_CF_CD IRQ_GPIO(PCM990_CF_CD_GPIO) |
| #define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING |
| |
| #define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */ |
| #define PCM990_CF_PLD_BASE 0xef000000 |
| #define PCM990_CF_PLD_SIZE (1*1024*1024) |
| #define PCM990_CF_PLD_P2V(x) ((x) - PCM990_CF_PLD_PHYS + PCM990_CF_PLD_BASE) |
| #define PCM990_CF_PLD_V2P(x) ((x) - PCM990_CF_PLD_BASE + PCM990_CF_PLD_PHYS) |
| |
| /* visible CPLD (U6) registers */ |
| #define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */ |
| #define PCM990_CF_REG0_LED 0x0001 /* RW LED on */ |
| #define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */ |
| #define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */ |
| #define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */ |
| |
| #define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */ |
| #define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */ |
| #define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */ |
| |
| #define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */ |
| #define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */ |
| #define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */ |
| #define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */ |
| |
| #define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */ |
| #define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */ |
| #define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */ |
| #define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */ |
| #define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */ |
| |
| #define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */ |
| #define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */ |
| #define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */ |
| #define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */ |
| #define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */ |
| |
| #define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */ |
| #define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */ |
| #define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */ |
| #define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */ |
| #define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */ |
| |
| #define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */ |
| #define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */ |
| #define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */ |
| |
| #ifndef __ASSEMBLY__ |
| # define __PCM990_CF_PLD_REG(x) \ |
| (*((volatile unsigned char *)PCM990_CF_PLD_P2V(x))) |
| #else |
| # define __PCM990_CF_PLD_REG(x) PCM990_CF_PLD_P2V(x) |
| #endif |
| |
| #define PCM990_CF0 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG0) |
| #define PCM990_CF1 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG1) |
| #define PCM990_CF2 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG2) |
| #define PCM990_CF3 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG3) |
| #define PCM990_CF4 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG4) |
| #define PCM990_CF5 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG5) |
| #define PCM990_CF6 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG6) |
| |
| /* |
| * Wolfson AC97 Touch |
| */ |
| #define PCM990_AC97_IRQ_GPIO 10 |
| #define PCM990_AC97_IRQ IRQ_GPIO(PCM990_AC97_IRQ_GPIO) |
| #define PCM990_AC97_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| |
| /* |
| * MMC phyCORE |
| */ |
| #define PCM990_MMC0_IRQ_GPIO 9 |
| #define PCM990_MMC0_IRQ IRQ_GPIO(PCM990_MMC0_IRQ_GPIO) |
| #define PCM990_MMC0_IRQ_EDGE IRQ_TYPE_EDGE_FALLING |
| |
| /* |
| * USB phyCore |
| */ |
| #define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN) |
| #define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT) |
