| Decoder firmware API description |
| ================================ |
| |
| Note: this API is part of the decoder firmware, so it's cx23415 only. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_PING_FW |
| Enum 0/0x00 |
| Description |
| This API call does nothing. It may be used to check if the firmware |
| is responding. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_START_PLAYBACK |
| Enum 1/0x01 |
| Description |
| Begin or resume playback. |
| Param[0] |
| 0 based frame number in GOP to begin playback from. |
| Param[1] |
| Specifies the number of muted audio frames to play before normal |
| audio resumes. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_STOP_PLAYBACK |
| Enum 2/0x02 |
| Description |
| Ends playback and clears all decoder buffers. If PTS is not zero, |
| playback stops at specified PTS. |
| Param[0] |
| Display 0=last frame, 1=black |
| Param[1] |
| PTS low |
| Param[2] |
| PTS high |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_PLAYBACK_SPEED |
| Enum 3/0x03 |
| Description |
| Playback stream at speed other than normal. There are two modes of |
| operation: |
| Smooth: host transfers entire stream and firmware drops unused |
| frames. |
| Coarse: host drops frames based on indexing as required to achieve |
| desired speed. |
| Param[0] |
| Bitmap: |
| 0:7 0 normal |
| 1 fast only "1.5 times" |
| n nX fast, 1/nX slow |
| 30 Framedrop: |
| '0' during 1.5 times play, every other B frame is dropped |
| '1' during 1.5 times play, stream is unchanged (bitrate |
| must not exceed 8mbps) |
| 31 Speed: |
| '0' slow |
| '1' fast |
| Param[1] |
| Direction: 0=forward, 1=reverse |
| Param[2] |
| Picture mask: |
| 1=I frames |
| 3=I, P frames |
| 7=I, P, B frames |
| Param[3] |
| B frames per GOP (for reverse play only) |
| Param[4] |
| Mute audio: 0=disable, 1=enable |
| Param[5] |
| Display 0=frame, 1=field |
| Param[6] |
| Specifies the number of muted audio frames to play before normal audio |
| resumes. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_STEP_VIDEO |
| Enum 5/0x05 |
| Description |
| Each call to this API steps the playback to the next unit defined below |
| in the current playback direction. |
| Param[0] |
| 0=frame, 1=top field, 2=bottom field |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_DMA_BLOCK_SIZE |
| Enum 8/0x08 |
| Description |
| Set DMA transfer block size. Counterpart to API 0xC9 |
| Param[0] |
| DMA transfer block size in bytes. A different size may be specified |
| when issuing the DMA transfer command. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_GET_XFER_INFO |
| Enum 9/0x09 |
| Description |
| This API call may be used to detect an end of stream condtion. |
| Result[0] |
| Stream type |
| Result[1] |
| Address offset |
| Result[2] |
| Maximum bytes to transfer |
| Result[3] |
| Buffer fullness |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_GET_DMA_STATUS |
| Enum 10/0x0A |
| Description |
| Status of the last DMA transfer |
| Result[0] |
| Bit 1 set means transfer complete |
| Bit 2 set means DMA error |
| Bit 3 set means linked list error |
| Result[1] |
| DMA type: 0=MPEG, 1=OSD, 2=YUV |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SCHED_DMA_FROM_HOST |
| Enum 11/0x0B |
| Description |
| Setup DMA from host operation. Counterpart to API 0xCC |
| Param[0] |
| Memory address of link list |
| Param[1] |
| Total # of bytes to transfer |
| Param[2] |
| DMA type (0=MPEG, 1=OSD, 2=YUV) |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_PAUSE_PLAYBACK |
| Enum 13/0x0D |
| Description |
| Freeze playback immediately. In this mode, when internal buffers are |
| full, no more data will be accepted and data request IRQs will be |
| masked. |
| Param[0] |
| Display: 0=last frame, 1=black |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_HALT_FW |
| Enum 14/0x0E |
| Description |
| The firmware is halted and no further API calls are serviced until |
| the firmware is uploaded again. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_STANDARD |
| Enum 16/0x10 |
| Description |
| Selects display standard |
| Param[0] |
| 0=NTSC, 1=PAL |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_GET_VERSION |
| Enum 17/0x11 |
| Description |
| Returns decoder firmware version information |
| Result[0] |
| Version bitmask: |
| Bits 0:15 build |
| Bits 16:23 minor |
| Bits 24:31 major |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_STREAM_INPUT |
| Enum 20/0x14 |
| Description |
| Select decoder stream input port |
| Param[0] |
| 0=memory (default), 1=streaming |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_GET_TIMING_INFO |
| Enum 21/0x15 |
| Description |
| Returns timing information from start of playback |
| Result[0] |
| Frame count by decode order |
| Result[1] |
| Video PTS bits 0:31 by display order |
| Result[2] |
| Video PTS bit 32 by display order |
| Result[3] |
| SCR bits 0:31 by display order |
| Result[4] |
| SCR bit 32 by display order |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_AUDIO_MODE |
| Enum 22/0x16 |
| Description |
| Select audio mode |
| Param[0] |
| Dual mono mode action |
| Param[1] |
| Stereo mode action: |
| 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_EVENT_NOTIFICATION |
| Enum 23/0x17 |
| Description |
| Setup firmware to notify the host about a particular event. |
| Counterpart to API 0xD5 |
| Param[0] |
| Event: 0=Audio mode change between stereo and dual channel |
| Param[1] |
| Notification 0=disabled, 1=enabled |
| Param[2] |
| Interrupt bit |
| Param[3] |
| Mailbox slot, -1 if no mailbox required. |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_DISPLAY_BUFFERS |
| Enum 24/0x18 |
| Description |
| Number of display buffers. To decode all frames in reverse playback you |
| must use nine buffers. |
| Param[0] |
| 0=six buffers, 1=nine buffers |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_EXTRACT_VBI |
| Enum 25/0x19 |
| Description |
| Extracts VBI data |
| Param[0] |
| 0=extract from extension & user data, 1=extract from private packets |
| Result[0] |
| VBI table location |
| Result[1] |
| VBI table size |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_DECODER_SOURCE |
| Enum 26/0x1A |
| Description |
| Selects decoder source. Ensure that the parameters passed to this |
| API match the encoder settings. |
| Param[0] |
| Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host |
| Param[1] |
| YUV picture width |
| Param[2] |
| YUV picture height |
| Param[3] |
| Bitmap: see Param[0] of API 0xBD |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_AUDIO_OUTPUT |
| Enum 27/0x1B |
| Description |
| Select audio output format |
| Param[0] |
| Bitmask: |
| 0:1 Data size: |
| '00' 16 bit |
| '01' 20 bit |
| '10' 24 bit |
| 2:7 Unused |
| 8:9 Mode: |
| '00' 2 channels |
| '01' 4 channels |
| '10' 6 channels |
| '11' 6 channels with one line data mode |
| (for left justified MSB first mode, 20 bit only) |
| 10:11 Unused |
| 12:13 Channel format: |
| '00' right justified MSB first mode |
| '01' left justified MSB first mode |
| '10' I2S mode |
| 14:15 Unused |
| 16:21 Right justify bit count |
| 22:31 Unused |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_AV_DELAY |
| Enum 28/0x1C |
| Description |
| Set audio/video delay in 90Khz ticks |
| Param[0] |
| 0=A/V in sync, negative=audio lags, positive=video lags |
| |
| ------------------------------------------------------------------------------- |
| |
| Name CX2341X_DEC_SET_PREBUFFERING |
| Enum 30/0x1E |
| Description |
| Decoder prebuffering, when enabled up to 128KB are buffered for |
| streams <8mpbs or 640KB for streams >8mbps |
| Param[0] |
| 0=off, 1=on |
