| #ifndef _IPATH_KERNEL_H |
| #define _IPATH_KERNEL_H |
| /* |
| * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. |
| * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. |
| * |
| * This software is available to you under a choice of one of two |
| * licenses. You may choose to be licensed under the terms of the GNU |
| * General Public License (GPL) Version 2, available from the file |
| * COPYING in the main directory of this source tree, or the |
| * OpenIB.org BSD license below: |
| * |
| * Redistribution and use in source and binary forms, with or |
| * without modification, are permitted provided that the following |
| * conditions are met: |
| * |
| * - Redistributions of source code must retain the above |
| * copyright notice, this list of conditions and the following |
| * disclaimer. |
| * |
| * - Redistributions in binary form must reproduce the above |
| * copyright notice, this list of conditions and the following |
| * disclaimer in the documentation and/or other materials |
| * provided with the distribution. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS |
| * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN |
| * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN |
| * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE |
| * SOFTWARE. |
| */ |
| |
| /* |
| * This header file is the base header file for infinipath kernel code |
| * ipath_user.h serves a similar purpose for user code. |
| */ |
| |
| #include <linux/interrupt.h> |
| #include <linux/pci.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/mutex.h> |
| #include <linux/list.h> |
| #include <linux/scatterlist.h> |
| #include <asm/io.h> |
| #include <rdma/ib_verbs.h> |
| |
| #include "ipath_common.h" |
| #include "ipath_debug.h" |
| #include "ipath_registers.h" |
| |
| /* only s/w major version of InfiniPath we can handle */ |
| #define IPATH_CHIP_VERS_MAJ 2U |
| |
| /* don't care about this except printing */ |
| #define IPATH_CHIP_VERS_MIN 0U |
| |
| /* temporary, maybe always */ |
| extern struct infinipath_stats ipath_stats; |
| |
| #define IPATH_CHIP_SWVERSION IPATH_CHIP_VERS_MAJ |
| /* |
| * First-cut critierion for "device is active" is |
| * two thousand dwords combined Tx, Rx traffic per |
| * 5-second interval. SMA packets are 64 dwords, |
| * and occur "a few per second", presumably each way. |
| */ |
| #define IPATH_TRAFFIC_ACTIVE_THRESHOLD (2000) |
| /* |
| * Struct used to indicate which errors are logged in each of the |
| * error-counters that are logged to EEPROM. A counter is incremented |
| * _once_ (saturating at 255) for each event with any bits set in |
| * the error or hwerror register masks below. |
| */ |
| #define IPATH_EEP_LOG_CNT (4) |
| struct ipath_eep_log_mask { |
| u64 errs_to_log; |
| u64 hwerrs_to_log; |
| }; |
| |
| struct ipath_portdata { |
| void **port_rcvegrbuf; |
| dma_addr_t *port_rcvegrbuf_phys; |
| /* rcvhdrq base, needs mmap before useful */ |
| void *port_rcvhdrq; |
| /* kernel virtual address where hdrqtail is updated */ |
| void *port_rcvhdrtail_kvaddr; |
| /* |
| * temp buffer for expected send setup, allocated at open, instead |
| * of each setup call |
| */ |
| void *port_tid_pg_list; |
| /* when waiting for rcv or pioavail */ |
| wait_queue_head_t port_wait; |
| /* |
| * rcvegr bufs base, physical, must fit |
| * in 44 bits so 32 bit programs mmap64 44 bit works) |
| */ |
| dma_addr_t port_rcvegr_phys; |
| /* mmap of hdrq, must fit in 44 bits */ |
| dma_addr_t port_rcvhdrq_phys; |
| dma_addr_t port_rcvhdrqtailaddr_phys; |
| /* |
| * number of opens (including slave subports) on this instance |
| * (ignoring forks, dup, etc. for now) |
| */ |
| int port_cnt; |
| /* |
| * how much space to leave at start of eager TID entries for |
| * protocol use, on each TID |
| */ |
| /* instead of calculating it */ |
| unsigned port_port; |
| /* non-zero if port is being shared. */ |
| u16 port_subport_cnt; |
| /* non-zero if port is being shared. */ |
| u16 port_subport_id; |
| /* number of pio bufs for this port (all procs, if shared) */ |
| u32 port_piocnt; |
| /* first pio buffer for this port */ |
| u32 port_pio_base; |
| /* chip offset of PIO buffers for this port */ |
| u32 port_piobufs; |
| /* how many alloc_pages() chunks in port_rcvegrbuf_pages */ |
| u32 port_rcvegrbuf_chunks; |
| /* how many egrbufs per chunk */ |
| u32 port_rcvegrbufs_perchunk; |
| /* order for port_rcvegrbuf_pages */ |
| size_t port_rcvegrbuf_size; |
| /* rcvhdrq size (for freeing) */ |
| size_t port_rcvhdrq_size; |
| /* next expected TID to check when looking for free */ |
| u32 port_tidcursor; |
| /* next expected TID to check */ |
| unsigned long port_flag; |
| /* what happened */ |
| unsigned long int_flag; |
| /* WAIT_RCV that timed out, no interrupt */ |
| u32 port_rcvwait_to; |
| /* WAIT_PIO that timed out, no interrupt */ |
| u32 port_piowait_to; |
| /* WAIT_RCV already happened, no wait */ |
| u32 port_rcvnowait; |
| /* WAIT_PIO already happened, no wait */ |
| u32 port_pionowait; |
| /* total number of rcvhdrqfull errors */ |
| u32 port_hdrqfull; |
| /* |
| * Used to suppress multiple instances of same |
| * port staying stuck at same point. |
| */ |
| u32 port_lastrcvhdrqtail; |
| /* saved total number of rcvhdrqfull errors for poll edge trigger */ |
| u32 port_hdrqfull_poll; |
| /* total number of polled urgent packets */ |
| u32 port_urgent; |
| /* saved total number of polled urgent packets for poll edge trigger */ |
| u32 port_urgent_poll; |
| /* pid of process using this port */ |
| struct pid *port_pid; |
| struct pid *port_subpid[INFINIPATH_MAX_SUBPORT]; |
| /* same size as task_struct .comm[] */ |
| char port_comm[16]; |
| /* pkeys set by this use of this port */ |
| u16 port_pkeys[4]; |
| /* so file ops can get at unit */ |
| struct ipath_devdata *port_dd; |
| /* A page of memory for rcvhdrhead, rcvegrhead, rcvegrtail * N */ |
| void *subport_uregbase; |
| /* An array of pages for the eager receive buffers * N */ |
| void *subport_rcvegrbuf; |
| /* An array of pages for the eager header queue entries * N */ |
| void *subport_rcvhdr_base; |
| /* The version of the library which opened this port */ |
| u32 userversion; |
| /* Bitmask of active slaves */ |
| u32 active_slaves; |
| /* Type of packets or conditions we want to poll for */ |
| u16 poll_type; |
| /* port rcvhdrq head offset */ |
| u32 port_head; |
| /* receive packet sequence counter */ |
| u32 port_seq_cnt; |
| }; |
| |
| struct sk_buff; |
| struct ipath_sge_state; |
| struct ipath_verbs_txreq; |
| |
| /* |
| * control information for layered drivers |
| */ |
| struct _ipath_layer { |
| void *l_arg; |
| }; |
| |
| struct ipath_skbinfo { |
| struct sk_buff *skb; |
| dma_addr_t phys; |
| }; |
| |
| struct ipath_sdma_txreq { |
| int flags; |
| int sg_count; |
| union { |
| struct scatterlist *sg; |
| void *map_addr; |
| }; |
| void (*callback)(void *, int); |
| void *callback_cookie; |
| int callback_status; |
| u16 start_idx; /* sdma private */ |
| u16 next_descq_idx; /* sdma private */ |
| struct list_head list; /* sdma private */ |
| }; |
| |
| struct ipath_sdma_desc { |
| __le64 qw[2]; |
| }; |
| |
| #define IPATH_SDMA_TXREQ_F_USELARGEBUF 0x1 |
| #define IPATH_SDMA_TXREQ_F_HEADTOHOST 0x2 |
| #define IPATH_SDMA_TXREQ_F_INTREQ 0x4 |
| #define IPATH_SDMA_TXREQ_F_FREEBUF 0x8 |
| #define IPATH_SDMA_TXREQ_F_FREEDESC 0x10 |
| #define IPATH_SDMA_TXREQ_F_VL15 0x20 |
| |
| #define IPATH_SDMA_TXREQ_S_OK 0 |
| #define IPATH_SDMA_TXREQ_S_SENDERROR 1 |
| #define IPATH_SDMA_TXREQ_S_ABORTED 2 |
| #define IPATH_SDMA_TXREQ_S_SHUTDOWN 3 |
| |
| #define IPATH_SDMA_STATUS_SCORE_BOARD_DRAIN_IN_PROG (1ull << 63) |
| #define IPATH_SDMA_STATUS_ABORT_IN_PROG (1ull << 62) |
| #define IPATH_SDMA_STATUS_INTERNAL_SDMA_ENABLE (1ull << 61) |
| #define IPATH_SDMA_STATUS_SCB_EMPTY (1ull << 30) |
| |
| /* max dwords in small buffer packet */ |
| #define IPATH_SMALLBUF_DWORDS (dd->ipath_piosize2k >> 2) |
| |
| /* |
| * Possible IB config parameters for ipath_f_get/set_ib_cfg() |
| */ |
| #define IPATH_IB_CFG_LIDLMC 0 /* Get/set LID (LS16b) and Mask (MS16b) */ |
| #define IPATH_IB_CFG_HRTBT 1 /* Get/set Heartbeat off/enable/auto */ |
| #define IPATH_IB_HRTBT_ON 3 /* Heartbeat enabled, sent every 100msec */ |
| #define IPATH_IB_HRTBT_OFF 0 /* Heartbeat off */ |
| #define IPATH_IB_CFG_LWID_ENB 2 /* Get/set allowed Link-width */ |
| #define IPATH_IB_CFG_LWID 3 /* Get currently active Link-width */ |
| #define IPATH_IB_CFG_SPD_ENB 4 /* Get/set allowed Link speeds */ |
| #define IPATH_IB_CFG_SPD 5 /* Get current Link spd */ |
| #define IPATH_IB_CFG_RXPOL_ENB 6 /* Get/set Auto-RX-polarity enable */ |
| #define IPATH_IB_CFG_LREV_ENB 7 /* Get/set Auto-Lane-reversal enable */ |
| #define IPATH_IB_CFG_LINKLATENCY 8 /* Get Auto-Lane-reversal enable */ |
| |
| |
| struct ipath_devdata { |
| struct list_head ipath_list; |
| |
| struct ipath_kregs const *ipath_kregs; |
| struct ipath_cregs const *ipath_cregs; |
| |
| /* mem-mapped pointer to base of chip regs */ |
| u64 __iomem *ipath_kregbase; |
| /* end of mem-mapped chip space; range checking */ |
| u64 __iomem *ipath_kregend; |
| /* physical address of chip for io_remap, etc. */ |
| unsigned long ipath_physaddr; |
| /* base of memory alloced for ipath_kregbase, for free */ |
| u64 *ipath_kregalloc; |
| /* ipath_cfgports pointers */ |
| struct ipath_portdata **ipath_pd; |
| /* sk_buffs used by port 0 eager receive queue */ |
| struct ipath_skbinfo *ipath_port0_skbinfo; |
| /* kvirt address of 1st 2k pio buffer */ |
| void __iomem *ipath_pio2kbase; |
| /* kvirt address of 1st 4k pio buffer */ |
| void __iomem *ipath_pio4kbase; |
| /* |
| * points to area where PIOavail registers will be DMA'ed. |
| * Has to be on a page of it's own, because the page will be |
| * mapped into user program space. This copy is *ONLY* ever |
| * written by DMA, not by the driver! Need a copy per device |
| * when we get to multiple devices |
| */ |
| volatile __le64 *ipath_pioavailregs_dma; |
| /* physical address where updates occur */ |
| dma_addr_t ipath_pioavailregs_phys; |
| struct _ipath_layer ipath_layer; |
| /* setup intr */ |
| int (*ipath_f_intrsetup)(struct ipath_devdata *); |
| /* fallback to alternate interrupt type if possible */ |
| int (*ipath_f_intr_fallback)(struct ipath_devdata *); |
| /* setup on-chip bus config */ |
| int (*ipath_f_bus)(struct ipath_devdata *, struct pci_dev *); |
| /* hard reset chip */ |
| int (*ipath_f_reset)(struct ipath_devdata *); |
| int (*ipath_f_get_boardname)(struct ipath_devdata *, char *, |
| size_t); |
| void (*ipath_f_init_hwerrors)(struct ipath_devdata *); |
| void (*ipath_f_handle_hwerrors)(struct ipath_devdata *, char *, |
| size_t); |
| void (*ipath_f_quiet_serdes)(struct ipath_devdata *); |
| int (*ipath_f_bringup_serdes)(struct ipath_devdata *); |
| int (*ipath_f_early_init)(struct ipath_devdata *); |
| void (*ipath_f_clear_tids)(struct ipath_devdata *, unsigned); |
| void (*ipath_f_put_tid)(struct ipath_devdata *, u64 __iomem*, |
| u32, unsigned long); |
| void (*ipath_f_tidtemplate)(struct ipath_devdata *); |
| void (*ipath_f_cleanup)(struct ipath_devdata *); |
| void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64); |
| /* fill out chip-specific fields */ |
| int (*ipath_f_get_base_info)(struct ipath_portdata *, void *); |
| /* free irq */ |
| void (*ipath_f_free_irq)(struct ipath_devdata *); |
| struct ipath_message_header *(*ipath_f_get_msgheader) |
| (struct ipath_devdata *, __le32 *); |
| void (*ipath_f_config_ports)(struct ipath_devdata *, ushort); |
| int (*ipath_f_get_ib_cfg)(struct ipath_devdata *, int); |
| int (*ipath_f_set_ib_cfg)(struct ipath_devdata *, int, u32); |
| void (*ipath_f_config_jint)(struct ipath_devdata *, u16 , u16); |
| void (*ipath_f_read_counters)(struct ipath_devdata *, |
| struct infinipath_counters *); |
| void (*ipath_f_xgxs_reset)(struct ipath_devdata *); |
| /* per chip actions needed for IB Link up/down changes */ |
| int (*ipath_f_ib_updown)(struct ipath_devdata *, int, u64); |
| |
| unsigned ipath_lastegr_idx; |
| struct ipath_ibdev *verbs_dev; |
| struct timer_list verbs_timer; |
| /* total dwords sent (summed from counter) */ |
| u64 ipath_sword; |
| /* total dwords rcvd (summed from counter) */ |
| u64 ipath_rword; |
| /* total packets sent (summed from counter) */ |
| u64 ipath_spkts; |
| /* total packets rcvd (summed from counter) */ |
| u64 ipath_rpkts; |
| /* ipath_statusp initially points to this. */ |
| u64 _ipath_status; |
| /* GUID for this interface, in network order */ |
| __be64 ipath_guid; |
| /* |
| * aggregrate of error bits reported since last cleared, for |
| * limiting of error reporting |
| */ |
| ipath_err_t ipath_lasterror; |
| /* |
| * aggregrate of error bits reported since last cleared, for |
| * limiting of hwerror reporting |
| */ |
| ipath_err_t ipath_lasthwerror; |
| /* errors masked because they occur too fast */ |
| ipath_err_t ipath_maskederrs; |
| u64 ipath_lastlinkrecov; /* link recoveries at last ACTIVE */ |
| /* these 5 fields are used to establish deltas for IB Symbol |
| * errors and linkrecovery errors. They can be reported on |
| * some chips during link negotiation prior to INIT, and with |
| * DDR when faking DDR negotiations with non-IBTA switches. |
| * The chip counters are adjusted at driver unload if there is |
| * a non-zero delta. |
| */ |
| u64 ibdeltainprog; |
| u64 ibsymdelta; |
| u64 ibsymsnap; |
| u64 iblnkerrdelta; |
| u64 iblnkerrsnap; |
| |
| /* time in jiffies at which to re-enable maskederrs */ |
| unsigned long ipath_unmasktime; |
| /* count of egrfull errors, combined for all ports */ |
| u64 ipath_last_tidfull; |
| /* for ipath_qcheck() */ |
| u64 ipath_lastport0rcv_cnt; |
| /* template for writing TIDs */ |
| u64 ipath_tidtemplate; |
| /* value to write to free TIDs */ |
| u64 ipath_tidinvalid; |
| /* IBA6120 rcv interrupt setup */ |
| u64 ipath_rhdrhead_intr_off; |
| |
| /* size of memory at ipath_kregbase */ |
| u32 ipath_kregsize; |
| /* number of registers used for pioavail */ |
| u32 ipath_pioavregs; |
| /* IPATH_POLL, etc. */ |
| u32 ipath_flags; |
| /* ipath_flags driver is waiting for */ |
| u32 ipath_state_wanted; |
| /* last buffer for user use, first buf for kernel use is this |
| * index. */ |
| u32 ipath_lastport_piobuf; |
| /* is a stats timer active */ |
| u32 ipath_stats_timer_active; |
| /* number of interrupts for this device -- saturates... */ |
| u32 ipath_int_counter; |
| /* dwords sent read from counter */ |
| u32 ipath_lastsword; |
| /* dwords received read from counter */ |
| u32 ipath_lastrword; |
| /* sent packets read from counter */ |
| u32 ipath_lastspkts; |
| /* received packets read from counter */ |
| u32 ipath_lastrpkts; |
| /* pio bufs allocated per port */ |
| u32 ipath_pbufsport; |
| /* if remainder on bufs/port, ports < extrabuf get 1 extra */ |
| u32 ipath_ports_extrabuf; |
| u32 ipath_pioupd_thresh; /* update threshold, some chips */ |
| /* |
| * number of ports configured as max; zero is set to number chip |
| * supports, less gives more pio bufs/port, etc. |
| */ |
| u32 ipath_cfgports; |
| /* count of port 0 hdrqfull errors */ |
| u32 ipath_p0_hdrqfull; |
| /* port 0 number of receive eager buffers */ |
| u32 ipath_p0_rcvegrcnt; |
| |
| /* |
| * index of last piobuffer we used. Speeds up searching, by |
| * starting at this point. Doesn't matter if multiple cpu's use and |
| * update, last updater is only write that matters. Whenever it |
| * wraps, we update shadow copies. Need a copy per device when we |
| * get to multiple devices |
| */ |
| u32 ipath_lastpioindex; |
| u32 ipath_lastpioindexl; |
| /* max length of freezemsg */ |
| u32 ipath_freezelen; |
| /* |
| * consecutive times we wanted a PIO buffer but were unable to |
| * get one |
| */ |
| u32 ipath_consec_nopiobuf; |
| /* |
| * hint that we should update ipath_pioavailshadow before |
| * looking for a PIO buffer |
| */ |
| u32 ipath_upd_pio_shadow; |
| /* so we can rewrite it after a chip reset */ |
| u32 ipath_pcibar0; |
| /* so we can rewrite it after a chip reset */ |
| u32 ipath_pcibar1; |
| u32 ipath_x1_fix_tries; |
| u32 ipath_autoneg_tries; |
| u32 serdes_first_init_done; |
| |
| struct ipath_relock { |
| atomic_t ipath_relock_timer_active; |
| struct timer_list ipath_relock_timer; |
| unsigned int ipath_relock_interval; /* in jiffies */ |
| } ipath_relock_singleton; |
| |
| /* interrupt number */ |
| int ipath_irq; |
| /* HT/PCI Vendor ID (here for NodeInfo) */ |
| u16 ipath_vendorid; |
| /* HT/PCI Device ID (here for NodeInfo) */ |
| u16 ipath_deviceid; |
| /* offset in HT config space of slave/primary interface block */ |
| u8 ipath_ht_slave_off; |
| /* for write combining settings */ |
| unsigned long ipath_wc_cookie; |
| unsigned long ipath_wc_base; |
| unsigned long ipath_wc_len; |
| /* ref count for each pkey */ |
| atomic_t ipath_pkeyrefs[4]; |
| /* shadow copy of struct page *'s for exp tid pages */ |
| struct page **ipath_pageshadow; |
| /* shadow copy of dma handles for exp tid pages */ |
| dma_addr_t *ipath_physshadow; |
| u64 __iomem *ipath_egrtidbase; |
| /* lock to workaround chip bug 9437 and others */ |
| spinlock_t ipath_kernel_tid_lock; |
| spinlock_t ipath_user_tid_lock; |
| spinlock_t ipath_sendctrl_lock; |
| /* around ipath_pd and (user ports) port_cnt use (intr vs free) */ |
| spinlock_t ipath_uctxt_lock; |
| |
| /* |
| * IPATH_STATUS_*, |
| * this address is mapped readonly into user processes so they can |
| * get status cheaply, whenever they want. |
| */ |
| u64 *ipath_statusp; |
| /* freeze msg if hw error put chip in freeze */ |
| char *ipath_freezemsg; |
| /* pci access data structure */ |
| struct pci_dev *pcidev; |
| struct cdev *user_cdev; |
| struct cdev *diag_cdev; |
| struct device *user_dev; |
| struct device *diag_dev; |
| /* timer used to prevent stats overflow, error throttling, etc. */ |
| struct timer_list ipath_stats_timer; |
| /* timer to verify interrupts work, and fallback if possible */ |
| struct timer_list ipath_intrchk_timer; |
| void *ipath_dummy_hdrq; /* used after port close */ |
| dma_addr_t ipath_dummy_hdrq_phys; |
| |
| /* SendDMA related entries */ |
| spinlock_t ipath_sdma_lock; |
| unsigned long ipath_sdma_status; |
| unsigned long ipath_sdma_abort_jiffies; |
| unsigned long ipath_sdma_abort_intr_timeout; |
| unsigned long ipath_sdma_buf_jiffies; |
| struct ipath_sdma_desc *ipath_sdma_descq; |
| u64 ipath_sdma_descq_added; |
| u64 ipath_sdma_descq_removed; |
| int ipath_sdma_desc_nreserved; |
| u16 ipath_sdma_descq_cnt; |
| u16 ipath_sdma_descq_tail; |
| u16 ipath_sdma_descq_head; |
| u16 ipath_sdma_next_intr; |
| u16 ipath_sdma_reset_wait; |
| u8 ipath_sdma_generation; |
| struct tasklet_struct ipath_sdma_abort_task; |
| struct tasklet_struct ipath_sdma_notify_task; |
| struct list_head ipath_sdma_activelist; |
| struct list_head ipath_sdma_notifylist; |
| atomic_t ipath_sdma_vl15_count; |
| struct timer_list ipath_sdma_vl15_timer; |
| |
| dma_addr_t ipath_sdma_descq_phys; |
| volatile __le64 *ipath_sdma_head_dma; |
| dma_addr_t ipath_sdma_head_phys; |
| |
| unsigned long ipath_ureg_align; /* user register alignment */ |
| |
| struct delayed_work ipath_autoneg_work; |
| wait_queue_head_t ipath_autoneg_wait; |
| |
| /* HoL blocking / user app forward-progress state */ |
| unsigned ipath_hol_state; |
| unsigned ipath_hol_next; |
| struct timer_list ipath_hol_timer; |
| |
| /* |
| * Shadow copies of registers; size indicates read access size. |
| * Most of them are readonly, but some are write-only register, |
| * where we manipulate the bits in the shadow copy, and then write |
| * the shadow copy to infinipath. |
| * |
| * We deliberately make most of these 32 bits, since they have |
| * restricted range. For any that we read, we won't to generate 32 |
| * bit accesses, since Opteron will generate 2 separate 32 bit HT |
| * transactions for a 64 bit read, and we want to avoid unnecessary |
| * HT transactions. |
| */ |
| |
| /* This is the 64 bit group */ |
| |
| /* |
| * shadow of pioavail, check to be sure it's large enough at |
| * init time. |
| */ |
| unsigned long ipath_pioavailshadow[8]; |
| /* bitmap of send buffers available for the kernel to use with PIO. */ |
| unsigned long ipath_pioavailkernel[8]; |
| /* shadow of kr_gpio_out, for rmw ops */ |
| u64 ipath_gpio_out; |
| /* shadow the gpio mask register */ |
| u64 ipath_gpio_mask; |
| /* shadow the gpio output enable, etc... */ |
| u64 ipath_extctrl; |
| /* kr_revision shadow */ |
| u64 ipath_revision; |
| /* |
| * shadow of ibcctrl, for interrupt handling of link changes, |
| * etc. |
| */ |
| u64 ipath_ibcctrl; |
| /* |
| * last ibcstatus, to suppress "duplicate" status change messages, |
| * mostly from 2 to 3 |
| */ |
| u64 ipath_lastibcstat; |
| /* hwerrmask shadow */ |
| ipath_err_t ipath_hwerrmask; |
| ipath_err_t ipath_errormask; /* errormask shadow */ |
| /* interrupt config reg shadow */ |
| u64 ipath_intconfig; |
| /* kr_sendpiobufbase value */ |
| u64 ipath_piobufbase; |
| /* kr_ibcddrctrl shadow */ |
| u64 ipath_ibcddrctrl; |
| |
| /* these are the "32 bit" regs */ |
| |
| /* |
| * number of GUIDs in the flash for this interface; may need some |
| * rethinking for setting on other ifaces |
| */ |
| u32 ipath_nguid; |
| /* |
| * the following two are 32-bit bitmasks, but {test,clear,set}_bit |
| * all expect bit fields to be "unsigned long" |
| */ |
| /* shadow kr_rcvctrl */ |
| unsigned long ipath_rcvctrl; |
| /* shadow kr_sendctrl */ |
| unsigned long ipath_sendctrl; |
| /* to not count armlaunch after cancel */ |
| unsigned long ipath_lastcancel; |
| /* count cases where special trigger was needed (double write) */ |
| unsigned long ipath_spectriggerhit; |
| |
| /* value we put in kr_rcvhdrcnt */ |
| u32 ipath_rcvhdrcnt; |
| /* value we put in kr_rcvhdrsize */ |
| u32 ipath_rcvhdrsize; |
| /* value we put in kr_rcvhdrentsize */ |
| u32 ipath_rcvhdrentsize; |
| /* offset of last entry in rcvhdrq */ |
| u32 ipath_hdrqlast; |
| /* kr_portcnt value */ |
| u32 ipath_portcnt; |
| /* kr_pagealign value */ |
| u32 ipath_palign; |
| /* number of "2KB" PIO buffers */ |
| u32 ipath_piobcnt2k; |
| /* size in bytes of "2KB" PIO buffers */ |
| u32 ipath_piosize2k; |
| /* number of "4KB" PIO buffers */ |
| u32 ipath_piobcnt4k; |
| /* size in bytes of "4KB" PIO buffers */ |
| u32 ipath_piosize4k; |
| u32 ipath_pioreserved; /* reserved special-inkernel; */ |
| /* kr_rcvegrbase value */ |
| u32 ipath_rcvegrbase; |
| /* kr_rcvegrcnt value */ |
| u32 ipath_rcvegrcnt; |
| /* kr_rcvtidbase value */ |
| u32 ipath_rcvtidbase; |
| /* kr_rcvtidcnt value */ |
| u32 ipath_rcvtidcnt; |
| /* kr_sendregbase */ |
| u32 ipath_sregbase; |
| /* kr_userregbase */ |
| u32 ipath_uregbase; |
| /* kr_counterregbase */ |
| u32 ipath_cregbase; |
| /* shadow the control register contents */ |
| u32 ipath_control; |
| /* PCI revision register (HTC rev on FPGA) */ |
| u32 ipath_pcirev; |
| |
| /* chip address space used by 4k pio buffers */ |
| u32 ipath_4kalign; |
| /* The MTU programmed for this unit */ |
| u32 ipath_ibmtu; |
| /* |
| * The max size IB packet, included IB headers that we can send. |
| * Starts same as ipath_piosize, but is affected when ibmtu is |
| * changed, or by size of eager buffers |
| */ |
| u32 ipath_ibmaxlen; |
| /* |
| * ibmaxlen at init time, limited by chip and by receive buffer |
| * size. Not changed after init. |
| */ |
| u32 ipath_init_ibmaxlen; |
| /* size of each rcvegrbuffer */ |
| u32 ipath_rcvegrbufsize; |
| /* localbus width (1, 2,4,8,16,32) from config space */ |
| u32 ipath_lbus_width; |
| /* localbus speed (HT: 200,400,800,1000; PCIe 2500) */ |
| u32 ipath_lbus_speed; |
| /* |
| * number of sequential ibcstatus change for polling active/quiet |
| * (i.e., link not coming up). |
| */ |
| u32 ipath_ibpollcnt; |
| /* low and high portions of MSI capability/vector */ |
| u32 ipath_msi_lo; |
| /* saved after PCIe init for restore after reset */ |
| u32 ipath_msi_hi; |
| /* MSI data (vector) saved for restore */ |
| u16 ipath_msi_data; |
| /* MLID programmed for this instance */ |
| u16 ipath_mlid; |
| /* LID programmed for this instance */ |
| u16 ipath_lid; |
| /* list of pkeys programmed; 0 if not set */ |
| u16 ipath_pkeys[4]; |
| /* |
| * ASCII serial number, from flash, large enough for original |
| * all digit strings, and longer QLogic serial number format |
| */ |
| u8 ipath_serial[16]; |
| /* human readable board version */ |
| u8 ipath_boardversion[96]; |
| u8 ipath_lbus_info[32]; /* human readable localbus info */ |
| /* chip major rev, from ipath_revision */ |
| u8 ipath_majrev; |
| /* chip minor rev, from ipath_revision */ |
| u8 ipath_minrev; |
| /* board rev, from ipath_revision */ |
| u8 ipath_boardrev; |
| /* saved for restore after reset */ |
| u8 ipath_pci_cacheline; |
| /* LID mask control */ |
| u8 ipath_lmc; |
| /* link width supported */ |
| u8 ipath_link_width_supported; |
| /* link speed supported */ |
| u8 ipath_link_speed_supported; |
| u8 ipath_link_width_enabled; |
| u8 ipath_link_speed_enabled; |
| u8 ipath_link_width_active; |
| u8 ipath_link_speed_active; |
| /* Rx Polarity inversion (compensate for ~tx on partner) */ |
| u8 ipath_rx_pol_inv; |
| |
| u8 ipath_r_portenable_shift; |
| u8 ipath_r_intravail_shift; |
| u8 ipath_r_tailupd_shift; |
| u8 ipath_r_portcfg_shift; |
| |
| /* unit # of this chip, if present */ |
| int ipath_unit; |
| |
| /* local link integrity counter */ |
| u32 ipath_lli_counter; |
| /* local link integrity errors */ |
| u32 ipath_lli_errors; |
| /* |
| * Above counts only cases where _successive_ LocalLinkIntegrity |
| * errors were seen in the receive headers of kern-packets. |
| * Below are the three (monotonically increasing) counters |
| * maintained via GPIO interrupts on iba6120-rev2. |
| */ |
| u32 ipath_rxfc_unsupvl_errs; |
| u32 ipath_overrun_thresh_errs; |
| u32 ipath_lli_errs; |
| |
| /* |
| * Not all devices managed by a driver instance are the same |
| * type, so these fields must be per-device. |
| */ |
| u64 ipath_i_bitsextant; |
| ipath_err_t ipath_e_bitsextant; |
| ipath_err_t ipath_hwe_bitsextant; |
| |
| /* |
| * Below should be computable from number of ports, |
| * since they are never modified. |
| */ |
| u64 ipath_i_rcvavail_mask; |
| u64 ipath_i_rcvurg_mask; |
| u16 ipath_i_rcvurg_shift; |
| u16 ipath_i_rcvavail_shift; |
| |
| /* |
| * Register bits for selecting i2c direction and values, used for |
| * I2C serial flash. |
| */ |
| u8 ipath_gpio_sda_num; |
| u8 ipath_gpio_scl_num; |
| u8 ipath_i2c_chain_type; |
| u64 ipath_gpio_sda; |
| u64 ipath_gpio_scl; |
| |
| /* lock for doing RMW of shadows/regs for ExtCtrl and GPIO */ |
| spinlock_t ipath_gpio_lock; |
| |
| /* |
| * IB link and linktraining states and masks that vary per chip in |
| * some way. Set at init, to avoid each IB status change interrupt |
| */ |
| u8 ibcs_ls_shift; |
| u8 ibcs_lts_mask; |
| u32 ibcs_mask; |
| u32 ib_init; |
| u32 ib_arm; |
| u32 ib_active; |
| |
| u16 ipath_rhf_offset; /* offset of RHF within receive header entry */ |
| |
| /* |
| * shift/mask for linkcmd, linkinitcmd, maxpktlen in ibccontol |
| * reg. Changes for IBA7220 |
| */ |
| u8 ibcc_lic_mask; /* LinkInitCmd */ |
| u8 ibcc_lc_shift; /* LinkCmd */ |
| u8 ibcc_mpl_shift; /* Maxpktlen */ |
| |
| u8 delay_mult; |
| |
| /* used to override LED behavior */ |
| u8 ipath_led_override; /* Substituted for normal value, if non-zero */ |
| u16 ipath_led_override_timeoff; /* delta to next timer event */ |
| u8 ipath_led_override_vals[2]; /* Alternates per blink-frame */ |
| u8 ipath_led_override_phase; /* Just counts, LSB picks from vals[] */ |
| atomic_t ipath_led_override_timer_active; |
| /* Used to flash LEDs in override mode */ |
| struct timer_list ipath_led_override_timer; |
| |
| /* Support (including locks) for EEPROM logging of errors and time */ |
| /* control access to actual counters, timer */ |
| spinlock_t ipath_eep_st_lock; |
| /* control high-level access to EEPROM */ |
| struct mutex ipath_eep_lock; |
| /* Below inc'd by ipath_snap_cntrs(), locked by ipath_eep_st_lock */ |
| uint64_t ipath_traffic_wds; |
| /* active time is kept in seconds, but logged in hours */ |
| atomic_t ipath_active_time; |
| /* Below are nominal shadow of EEPROM, new since last EEPROM update */ |
| uint8_t ipath_eep_st_errs[IPATH_EEP_LOG_CNT]; |
| uint8_t ipath_eep_st_new_errs[IPATH_EEP_LOG_CNT]; |
| uint16_t ipath_eep_hrs; |
| /* |
| * masks for which bits of errs, hwerrs that cause |
| * each of the counters to increment. |
| */ |
| struct ipath_eep_log_mask ipath_eep_st_masks[IPATH_EEP_LOG_CNT]; |
| |
| /* interrupt mitigation reload register info */ |
| u16 ipath_jint_idle_ticks; /* idle clock ticks */ |
| u16 ipath_jint_max_packets; /* max packets across all ports */ |
| |
| /* |
| * lock for access to SerDes, and flags to sequence preset |
| * versus steady-state. 7220-only at the moment. |
| */ |
| spinlock_t ipath_sdepb_lock; |
| u8 ipath_presets_needed; /* Set if presets to be restored next DOWN */ |
| }; |
| |
| /* ipath_hol_state values (stopping/starting user proc, send flushing) */ |
| #define IPATH_HOL_UP 0 |
| #define IPATH_HOL_DOWN 1 |
| /* ipath_hol_next toggle values, used when hol_state IPATH_HOL_DOWN */ |
| #define IPATH_HOL_DOWNSTOP 0 |
| #define IPATH_HOL_DOWNCONT 1 |
| |
| /* bit positions for sdma_status */ |
| #define IPATH_SDMA_ABORTING 0 |
| #define IPATH_SDMA_DISARMED 1 |
| #define IPATH_SDMA_DISABLED 2 |
| #define IPATH_SDMA_LAYERBUF 3 |
| #define IPATH_SDMA_RUNNING 30 |
| #define IPATH_SDMA_SHUTDOWN 31 |
| |
| /* bit combinations that correspond to abort states */ |
| #define IPATH_SDMA_ABORT_NONE 0 |
| #define IPATH_SDMA_ABORT_ABORTING (1UL << IPATH_SDMA_ABORTING) |
| #define IPATH_SDMA_ABORT_DISARMED ((1UL << IPATH_SDMA_ABORTING) | \ |
| (1UL << IPATH_SDMA_DISARMED)) |
| #define IPATH_SDMA_ABORT_DISABLED ((1UL << IPATH_SDMA_ABORTING) | \ |
| (1UL << IPATH_SDMA_DISABLED)) |
| #define IPATH_SDMA_ABORT_ABORTED ((1UL << IPATH_SDMA_ABORTING) | \ |
| (1UL << IPATH_SDMA_DISARMED) | (1UL << IPATH_SDMA_DISABLED)) |
| #define IPATH_SDMA_ABORT_MASK ((1UL<<IPATH_SDMA_ABORTING) | \ |
| (1UL << IPATH_SDMA_DISARMED) | (1UL << IPATH_SDMA_DISABLED)) |
| |
| #define IPATH_SDMA_BUF_NONE 0 |
| #define IPATH_SDMA_BUF_MASK (1UL<<IPATH_SDMA_LAYERBUF) |
| |
| /* Private data for file operations */ |
| struct ipath_filedata { |
| struct ipath_portdata *pd; |
| unsigned subport; |
| unsigned tidcursor; |
| struct ipath_user_sdma_queue *pq; |
| }; |
| extern struct list_head ipath_dev_list; |
| extern spinlock_t ipath_devs_lock; |
| extern struct ipath_devdata *ipath_lookup(int unit); |
| |
| int ipath_init_chip(struct ipath_devdata *, int); |
| int ipath_enable_wc(struct ipath_devdata *dd); |
| void ipath_disable_wc(struct ipath_devdata *dd); |
| int ipath_count_units(int *npresentp, int *nupp, int *maxportsp); |
| void ipath_shutdown_device(struct ipath_devdata *); |
| void ipath_clear_freeze(struct ipath_devdata *); |
| |
| struct file_operations; |
| int ipath_cdev_init(int minor, char *name, const struct file_operations *fops, |
| struct cdev **cdevp, struct device **devp); |
| void ipath_cdev_cleanup(struct cdev **cdevp, |
| struct device **devp); |
| |
| int ipath_diag_add(struct ipath_devdata *); |
| void ipath_diag_remove(struct ipath_devdata *); |
| |
| extern wait_queue_head_t ipath_state_wait; |
| |
| int ipath_user_add(struct ipath_devdata *dd); |
| void ipath_user_remove(struct ipath_devdata *dd); |
| |
| struct sk_buff *ipath_alloc_skb(struct ipath_devdata *dd, gfp_t); |
| |
| extern int ipath_diag_inuse; |
| |
| irqreturn_t ipath_intr(int irq, void *devid); |
| int ipath_decode_err(struct ipath_devdata *dd, char *buf, size_t blen, |
| ipath_err_t err); |
| #if __IPATH_INFO || __IPATH_DBG |
| extern const char *ipath_ibcstatus_str[]; |
| #endif |
| |
| /* clean up any per-chip chip-specific stuff */ |
| void ipath_chip_cleanup(struct ipath_devdata *); |
| /* clean up any chip type-specific stuff */ |
| void ipath_chip_done(void); |
| |
| /* check to see if we have to force ordering for write combining */ |
| int ipath_unordered_wc(void); |
| |
| void ipath_disarm_piobufs(struct ipath_devdata *, unsigned first, |
| unsigned cnt); |
| void ipath_cancel_sends(struct ipath_devdata *, int); |
| |
| int ipath_create_rcvhdrq(struct ipath_devdata *, struct ipath_portdata *); |
| void ipath_free_pddata(struct ipath_devdata *, struct ipath_portdata *); |
| |
| int ipath_parse_ushort(const char *str, unsigned short *valp); |
| |
| void ipath_kreceive(struct ipath_portdata *); |
| int ipath_setrcvhdrsize(struct ipath_devdata *, unsigned); |
| int ipath_reset_device(int); |
| void ipath_get_faststats(unsigned long); |
| int ipath_wait_linkstate(struct ipath_devdata *, u32, int); |
| int ipath_set_linkstate(struct ipath_devdata *, u8); |
| int ipath_set_mtu(struct ipath_devdata *, u16); |
| int ipath_set_lid(struct ipath_devdata *, u32, u8); |
| int ipath_set_rx_pol_inv(struct ipath_devdata *dd, u8 new_pol_inv); |
| void ipath_enable_armlaunch(struct ipath_devdata *); |
| void ipath_disable_armlaunch(struct ipath_devdata *); |
| void ipath_hol_down(struct ipath_devdata *); |
| void ipath_hol_up(struct ipath_devdata *); |
| void ipath_hol_event(unsigned long); |
| void ipath_toggle_rclkrls(struct ipath_devdata *); |
| void ipath_sd7220_clr_ibpar(struct ipath_devdata *); |
| void ipath_set_relock_poll(struct ipath_devdata *, int); |
| void ipath_shutdown_relock_poll(struct ipath_devdata *); |
| |
| /* for use in system calls, where we want to know device type, etc. */ |
| #define port_fp(fp) ((struct ipath_filedata *)(fp)->private_data)->pd |
| #define subport_fp(fp) \ |
| ((struct ipath_filedata *)(fp)->private_data)->subport |
| #define tidcursor_fp(fp) \ |
| ((struct ipath_filedata *)(fp)->private_data)->tidcursor |
| #define user_sdma_queue_fp(fp) \ |
| ((struct ipath_filedata *)(fp)->private_data)->pq |
| |
| /* |
| * values for ipath_flags |
| */ |
| /* chip can report link latency (IB 1.2) */ |
| #define IPATH_HAS_LINK_LATENCY 0x1 |
| /* The chip is up and initted */ |
| #define IPATH_INITTED 0x2 |
| /* set if any user code has set kr_rcvhdrsize */ |
| #define IPATH_RCVHDRSZ_SET 0x4 |
| /* The chip is present and valid for accesses */ |
| #define IPATH_PRESENT 0x8 |
| /* HT link0 is only 8 bits wide, ignore upper byte crc |
| * errors, etc. */ |
| #define IPATH_8BIT_IN_HT0 0x10 |
| /* HT link1 is only 8 bits wide, ignore upper byte crc |
| * errors, etc. */ |
| #define IPATH_8BIT_IN_HT1 0x20 |
| /* The link is down */ |
| #define IPATH_LINKDOWN 0x40 |
| /* The link level is up (0x11) */ |
| #define IPATH_LINKINIT 0x80 |
| /* The link is in the armed (0x21) state */ |
| #define IPATH_LINKARMED 0x100 |
| /* The link is in the active (0x31) state */ |
| #define IPATH_LINKACTIVE 0x200 |
| /* link current state is unknown */ |
| #define IPATH_LINKUNK 0x400 |
| /* Write combining flush needed for PIO */ |
| #define IPATH_PIO_FLUSH_WC 0x1000 |
| /* DMA Receive tail pointer */ |
| #define IPATH_NODMA_RTAIL 0x2000 |
| /* no IB cable, or no device on IB cable */ |
| #define IPATH_NOCABLE 0x4000 |
| /* Supports port zero per packet receive interrupts via |
| * GPIO */ |
| #define IPATH_GPIO_INTR 0x8000 |
| /* uses the coded 4byte TID, not 8 byte */ |
| #define IPATH_4BYTE_TID 0x10000 |
| /* packet/word counters are 32 bit, else those 4 counters |
| * are 64bit */ |
| #define IPATH_32BITCOUNTERS 0x20000 |
| /* Interrupt register is 64 bits */ |
| #define IPATH_INTREG_64 0x40000 |
| /* can miss port0 rx interrupts */ |
| #define IPATH_DISABLED 0x80000 /* administratively disabled */ |
| /* Use GPIO interrupts for new counters */ |
| #define IPATH_GPIO_ERRINTRS 0x100000 |
| #define IPATH_SWAP_PIOBUFS 0x200000 |
| /* Supports Send DMA */ |
| #define IPATH_HAS_SEND_DMA 0x400000 |
| /* Supports Send Count (not just word count) in PBC */ |
| #define IPATH_HAS_PBC_CNT 0x800000 |
| /* Suppress heartbeat, even if turning off loopback */ |
| #define IPATH_NO_HRTBT 0x1000000 |
| #define IPATH_HAS_THRESH_UPDATE 0x4000000 |
| #define IPATH_HAS_MULT_IB_SPEED 0x8000000 |
| #define IPATH_IB_AUTONEG_INPROG 0x10000000 |
| #define IPATH_IB_AUTONEG_FAILED 0x20000000 |
| /* Linkdown-disable intentionally, Do not attempt to bring up */ |
| #define IPATH_IB_LINK_DISABLED 0x40000000 |
| #define IPATH_IB_FORCE_NOTIFY 0x80000000 /* force notify on next ib change */ |
| |
| /* Bits in GPIO for the added interrupts */ |
| #define IPATH_GPIO_PORT0_BIT 2 |
| #define IPATH_GPIO_RXUVL_BIT 3 |
| #define IPATH_GPIO_OVRUN_BIT 4 |
| #define IPATH_GPIO_LLI_BIT 5 |
| #define IPATH_GPIO_ERRINTR_MASK 0x38 |
| |
| /* portdata flag bit offsets */ |
| /* waiting for a packet to arrive */ |
| #define IPATH_PORT_WAITING_RCV 2 |
| /* master has not finished initializing */ |
| #define IPATH_PORT_MASTER_UNINIT 4 |
| /* waiting for an urgent packet to arrive */ |
| #define IPATH_PORT_WAITING_URG 5 |
| |
| /* free up any allocated data at closes */ |
| void ipath_free_data(struct ipath_portdata *dd); |
| u32 __iomem *ipath_getpiobuf(struct ipath_devdata *, u32, u32 *); |
| void ipath_chg_pioavailkernel(struct ipath_devdata *dd, unsigned start, |
| unsigned len, int avail); |
| void ipath_init_iba6110_funcs(struct ipath_devdata *); |
| void ipath_get_eeprom_info(struct ipath_devdata *); |
| int ipath_update_eeprom_log(struct ipath_devdata *dd); |
| void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr); |
| u64 ipath_snap_cntr(struct ipath_devdata *, ipath_creg); |
| void ipath_disarm_senderrbufs(struct ipath_devdata *); |
| void ipath_force_pio_avail_update(struct ipath_devdata *); |
| void signal_ib_event(struct ipath_devdata *dd, enum ib_event_type ev); |
| |
| /* |
| * Set LED override, only the two LSBs have "public" meaning, but |
| * any non-zero value substitutes them for the Link and LinkTrain |
| * LED states. |
| */ |
| #define IPATH_LED_PHYS 1 /* Physical (linktraining) GREEN LED */ |
| #define IPATH_LED_LOG 2 /* Logical (link) YELLOW LED */ |
| void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val); |
| |
| /* send dma routines */ |
| int setup_sdma(struct ipath_devdata *); |
| void teardown_sdma(struct ipath_devdata *); |
| void ipath_restart_sdma(struct ipath_devdata *); |
| void ipath_sdma_intr(struct ipath_devdata *); |
| int ipath_sdma_verbs_send(struct ipath_devdata *, struct ipath_sge_state *, |
| u32, struct ipath_verbs_txreq *); |
| /* ipath_sdma_lock should be locked before calling this. */ |
| int ipath_sdma_make_progress(struct ipath_devdata *dd); |
| |
| /* must be called under ipath_sdma_lock */ |
| static inline u16 ipath_sdma_descq_freecnt(const struct ipath_devdata *dd) |
| { |
| return dd->ipath_sdma_descq_cnt - |
| (dd->ipath_sdma_descq_added - dd->ipath_sdma_descq_removed) - |
| 1 - dd->ipath_sdma_desc_nreserved; |
| } |
| |
| static inline void ipath_sdma_desc_reserve(struct ipath_devdata *dd, u16 cnt) |
| { |
| dd->ipath_sdma_desc_nreserved += cnt; |
| } |
| |
| static inline void ipath_sdma_desc_unreserve(struct ipath_devdata *dd, u16 cnt) |
| { |
| dd->ipath_sdma_desc_nreserved -= cnt; |
| } |
| |
| /* |
| * number of words used for protocol header if not set by ipath_userinit(); |
| */ |
| #define IPATH_DFLT_RCVHDRSIZE 9 |
| |
| int ipath_get_user_pages(unsigned long, size_t, struct page **); |
| void ipath_release_user_pages(struct page **, size_t); |
| void ipath_release_user_pages_on_close(struct page **, size_t); |
| int ipath_eeprom_read(struct ipath_devdata *, u8, void *, int); |
| int ipath_eeprom_write(struct ipath_devdata *, u8, const void *, int); |
| int ipath_tempsense_read(struct ipath_devdata *, u8 regnum); |
| int ipath_tempsense_write(struct ipath_devdata *, u8 regnum, u8 data); |
| |
| /* these are used for the registers that vary with port */ |
| void ipath_write_kreg_port(const struct ipath_devdata *, ipath_kreg, |
| unsigned, u64); |
| |
| /* |
| * We could have a single register get/put routine, that takes a group type, |
| * but this is somewhat clearer and cleaner. It also gives us some error |
| * checking. 64 bit register reads should always work, but are inefficient |
| * on opteron (the northbridge always generates 2 separate HT 32 bit reads), |
| * so we use kreg32 wherever possible. User register and counter register |
| * reads are always 32 bit reads, so only one form of those routines. |
| */ |
| |
| /* |
| * At the moment, none of the s-registers are writable, so no |
| * ipath_write_sreg(). |
| */ |
| |
| /** |
| * ipath_read_ureg32 - read 32-bit virtualized per-port register |
| * @dd: device |
| * @regno: register number |
| * @port: port number |
| * |
| * Return the contents of a register that is virtualized to be per port. |
| * Returns -1 on errors (not distinguishable from valid contents at |
| * runtime; we may add a separate error variable at some point). |
| */ |
| static inline u32 ipath_read_ureg32(const struct ipath_devdata *dd, |
| ipath_ureg regno, int port) |
| { |
| if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) |
| return 0; |
| |
| return readl(regno + (u64 __iomem *) |
| (dd->ipath_uregbase + |
| (char __iomem *)dd->ipath_kregbase + |
| dd->ipath_ureg_align * port)); |
| } |
| |
| /** |
| * ipath_write_ureg - write 32-bit virtualized per-port register |
| * @dd: device |
| * @regno: register number |
| * @value: value |
| * @port: port |
| * |
| * Write the contents of a register that is virtualized to be per port. |
| */ |
| static inline void ipath_write_ureg(const struct ipath_devdata *dd, |
| ipath_ureg regno, u64 value, int port) |
| { |
| u64 __iomem *ubase = (u64 __iomem *) |
| (dd->ipath_uregbase + (char __iomem *) dd->ipath_kregbase + |
| dd->ipath_ureg_align * port); |
| if (dd->ipath_kregbase) |
| writeq(value, &ubase[regno]); |
| } |
| |
| static inline u32 ipath_read_kreg32(const struct ipath_devdata *dd, |
| ipath_kreg regno) |
| { |
| if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) |
| return -1; |
| return readl((u32 __iomem *) & dd->ipath_kregbase[regno]); |
| } |
| |
| static inline u64 ipath_read_kreg64(const struct ipath_devdata *dd, |
| ipath_kreg regno) |
| { |
| if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) |
| return -1; |
| |
| return readq(&dd->ipath_kregbase[regno]); |
| } |
| |
| static inline void ipath_write_kreg(const struct ipath_devdata *dd, |
| ipath_kreg regno, u64 value) |
| { |
| if (dd->ipath_kregbase) |
| writeq(value, &dd->ipath_kregbase[regno]); |
| } |
| |
| static inline u64 ipath_read_creg(const struct ipath_devdata *dd, |
| ipath_sreg regno) |
| { |
| if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) |
| return 0; |
| |
| return readq(regno + (u64 __iomem *) |
| (dd->ipath_cregbase + |
| (char __iomem *)dd->ipath_kregbase)); |
| } |
| |
| static inline u32 ipath_read_creg32(const struct ipath_devdata *dd, |
| ipath_sreg regno) |
| { |
| if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) |
| return 0; |
| return readl(regno + (u64 __iomem *) |
| (dd->ipath_cregbase + |
| (char __iomem *)dd->ipath_kregbase)); |
| } |
| |
| static inline void ipath_write_creg(const struct ipath_devdata *dd, |
| ipath_creg regno, u64 value) |
| { |
| if (dd->ipath_kregbase) |
| writeq(value, regno + (u64 __iomem *) |
| (dd->ipath_cregbase + |
| (char __iomem *)dd->ipath_kregbase)); |
| } |
| |
| static inline void ipath_clear_rcvhdrtail(const struct ipath_portdata *pd) |
| { |
| *((u64 *) pd->port_rcvhdrtail_kvaddr) = 0ULL; |
| } |
| |
| static inline u32 ipath_get_rcvhdrtail(const struct ipath_portdata *pd) |
| { |
| return (u32) le64_to_cpu(*((volatile __le64 *) |
| pd->port_rcvhdrtail_kvaddr)); |
| } |
| |
| static inline u32 ipath_get_hdrqtail(const struct ipath_portdata *pd) |
| { |
| const struct ipath_devdata *dd = pd->port_dd; |
| u32 hdrqtail; |
| |
| if (dd->ipath_flags & IPATH_NODMA_RTAIL) { |
| __le32 *rhf_addr; |
| u32 seq; |
| |
| rhf_addr = (__le32 *) pd->port_rcvhdrq + |
| pd->port_head + dd->ipath_rhf_offset; |
| seq = ipath_hdrget_seq(rhf_addr); |
| hdrqtail = pd->port_head; |
| if (seq == pd->port_seq_cnt) |
| hdrqtail++; |
| } else |
| hdrqtail = ipath_get_rcvhdrtail(pd); |
| |
| return hdrqtail; |
| } |
| |
| static inline u64 ipath_read_ireg(const struct ipath_devdata *dd, ipath_kreg r) |
| { |
| return (dd->ipath_flags & IPATH_INTREG_64) ? |
| ipath_read_kreg64(dd, r) : ipath_read_kreg32(dd, r); |
| } |
| |
| /* |
| * from contents of IBCStatus (or a saved copy), return linkstate |
| * Report ACTIVE_DEFER as ACTIVE, because we treat them the same |
| * everywhere, anyway (and should be, for almost all purposes). |
| */ |
| static inline u32 ipath_ib_linkstate(struct ipath_devdata *dd, u64 ibcs) |
| { |
| u32 state = (u32)(ibcs >> dd->ibcs_ls_shift) & |
| INFINIPATH_IBCS_LINKSTATE_MASK; |
| if (state == INFINIPATH_IBCS_L_STATE_ACT_DEFER) |
| state = INFINIPATH_IBCS_L_STATE_ACTIVE; |
| return state; |
| } |
| |
| /* from contents of IBCStatus (or a saved copy), return linktrainingstate */ |
| static inline u32 ipath_ib_linktrstate(struct ipath_devdata *dd, u64 ibcs) |
| { |
| return (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) & |
| dd->ibcs_lts_mask; |
| } |
| |
| /* |
| * from contents of IBCStatus (or a saved copy), return logical link state |
| * combination of link state and linktraining state (down, active, init, |
| * arm, etc. |
| */ |
| static inline u32 ipath_ib_state(struct ipath_devdata *dd, u64 ibcs) |
| { |
| u32 ibs; |
| ibs = (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) & |
| dd->ibcs_lts_mask; |
| ibs |= (u32)(ibcs & |
| (INFINIPATH_IBCS_LINKSTATE_MASK << dd->ibcs_ls_shift)); |
| return ibs; |
| } |
| |
| /* |
| * sysfs interface. |
| */ |
| |
| struct device_driver; |
| |
| extern const char ib_ipath_version[]; |
| |
| extern const struct attribute_group *ipath_driver_attr_groups[]; |
| |
| int ipath_device_create_group(struct device *, struct ipath_devdata *); |
| void ipath_device_remove_group(struct device *, struct ipath_devdata *); |
| int ipath_expose_reset(struct device *); |
| |
| int ipath_init_ipathfs(void); |
| void ipath_exit_ipathfs(void); |
| int ipathfs_add_device(struct ipath_devdata *); |
| int ipathfs_remove_device(struct ipath_devdata *); |
| |
| /* |
| * dma_addr wrappers - all 0's invalid for hw |
| */ |
| dma_addr_t ipath_map_page(struct pci_dev *, struct page *, unsigned long, |
| size_t, int); |
| dma_addr_t ipath_map_single(struct pci_dev *, void *, size_t, int); |
| const char *ipath_get_unit_name(int unit); |
| |
| /* |
| * Flush write combining store buffers (if present) and perform a write |
| * barrier. |
| */ |
| #if defined(CONFIG_X86_64) |
| #define ipath_flush_wc() asm volatile("sfence" ::: "memory") |
| #else |
| #define ipath_flush_wc() wmb() |
| #endif |
| |
| extern unsigned ipath_debug; /* debugging bit mask */ |
| extern unsigned ipath_linkrecovery; |
| extern unsigned ipath_mtu4096; |
| extern struct mutex ipath_mutex; |
| |
| #define IPATH_DRV_NAME "ib_ipath" |
| #define IPATH_MAJOR 233 |
| #define IPATH_USER_MINOR_BASE 0 |
| #define IPATH_DIAGPKT_MINOR 127 |
| #define IPATH_DIAG_MINOR_BASE 129 |
| #define IPATH_NMINORS 255 |
| |
| #define ipath_dev_err(dd,fmt,...) \ |
| do { \ |
| const struct ipath_devdata *__dd = (dd); \ |
| if (__dd->pcidev) \ |
| dev_err(&__dd->pcidev->dev, "%s: " fmt, \ |
| ipath_get_unit_name(__dd->ipath_unit), \ |
| ##__VA_ARGS__); \ |
| else \ |
| printk(KERN_ERR IPATH_DRV_NAME ": %s: " fmt, \ |
| ipath_get_unit_name(__dd->ipath_unit), \ |
| ##__VA_ARGS__); \ |
| } while (0) |
| |
| #if _IPATH_DEBUGGING |
| |
| # define __IPATH_DBG_WHICH(which,fmt,...) \ |
| do { \ |
| if (unlikely(ipath_debug & (which))) \ |
| printk(KERN_DEBUG IPATH_DRV_NAME ": %s: " fmt, \ |
| __func__,##__VA_ARGS__); \ |
| } while(0) |
| |
| # define ipath_dbg(fmt,...) \ |
| __IPATH_DBG_WHICH(__IPATH_DBG,fmt,##__VA_ARGS__) |
| # define ipath_cdbg(which,fmt,...) \ |
| __IPATH_DBG_WHICH(__IPATH_##which##DBG,fmt,##__VA_ARGS__) |
| |
| #else /* ! _IPATH_DEBUGGING */ |
| |
| # define ipath_dbg(fmt,...) |
| # define ipath_cdbg(which,fmt,...) |
| |
| #endif /* _IPATH_DEBUGGING */ |
| |
| /* |
| * this is used for formatting hw error messages... |
| */ |
| struct ipath_hwerror_msgs { |
| u64 mask; |
| const char *msg; |
| }; |
| |
| #define INFINIPATH_HWE_MSG(a, b) { .mask = INFINIPATH_HWE_##a, .msg = b } |
| |
| /* in ipath_intr.c... */ |
| void ipath_format_hwerrors(u64 hwerrs, |
| const struct ipath_hwerror_msgs *hwerrmsgs, |
| size_t nhwerrmsgs, |
| char *msg, size_t lmsg); |
| |
| #endif /* _IPATH_KERNEL_H */ |