| /* |
| * arch/arm/mach-pxa/include/mach/pcm027.h |
| * |
| * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> |
| * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| */ |
| |
| /* |
| * Definitions of CPU card resources only |
| */ |
| |
| /* phyCORE-PXA270 (PCM027) Interrupts */ |
| #define PCM027_IRQ(x) (IRQ_BOARD_START + (x)) |
| #define PCM027_BTDET_IRQ PCM027_IRQ(0) |
| #define PCM027_FF_RI_IRQ PCM027_IRQ(1) |
| #define PCM027_MMCDET_IRQ PCM027_IRQ(2) |
| #define PCM027_PM_5V_IRQ PCM027_IRQ(3) |
| |
| #define PCM027_NR_IRQS (IRQ_BOARD_START + 32) |
| |
| /* I2C RTC */ |
| #define PCM027_RTC_IRQ_GPIO 0 |
| #define PCM027_RTC_IRQ PXA_GPIO_TO_IRQ(PCM027_RTC_IRQ_GPIO) |
| #define PCM027_RTC_IRQ_EDGE IRQ_TYPE_EDGE_FALLING |
| #define ADR_PCM027_RTC 0x51 /* I2C address */ |
| |
| /* I2C EEPROM */ |
| #define ADR_PCM027_EEPROM 0x54 /* I2C address */ |
| |
| /* Ethernet chip (SMSC91C111) */ |
| #define PCM027_ETH_IRQ_GPIO 52 |
| #define PCM027_ETH_IRQ PXA_GPIO_TO_IRQ(PCM027_ETH_IRQ_GPIO) |
| #define PCM027_ETH_IRQ_EDGE IRQ_TYPE_EDGE_RISING |
| #define PCM027_ETH_PHYS PXA_CS5_PHYS |
| #define PCM027_ETH_SIZE (1*1024*1024) |
| |
| /* CAN controller SJA1000 (unsupported yet) */ |
| #define PCM027_CAN_IRQ_GPIO 114 |
| #define PCM027_CAN_IRQ PXA_GPIO_TO_IRQ(PCM027_CAN_IRQ_GPIO) |
| #define PCM027_CAN_IRQ_EDGE IRQ_TYPE_EDGE_FALLING |
| #define PCM027_CAN_PHYS 0x22000000 |
| #define PCM027_CAN_SIZE 0x100 |
| |
| /* SPI GPIO expander (unsupported yet) */ |
| #define PCM027_EGPIO_IRQ_GPIO 27 |
| #define PCM027_EGPIO_IRQ PXA_GPIO_TO_IRQ(PCM027_EGPIO_IRQ_GPIO) |
| #define PCM027_EGPIO_IRQ_EDGE IRQ_TYPE_EDGE_FALLING |
| #define PCM027_EGPIO_CS 24 |
| /* |
| * TODO: Switch this pin from dedicated usage to GPIO if |
| * more than the MAX7301 device is connected to this SPI bus |
| */ |
| #define PCM027_EGPIO_CS_MODE GPIO24_SFRM_MD |
| |
| /* Flash memory */ |
| #define PCM027_FLASH_PHYS 0x00000000 |
| #define PCM027_FLASH_SIZE 0x02000000 |
| |
| /* onboard LEDs connected to GPIO */ |
| #define PCM027_LED_CPU 90 |
| #define PCM027_LED_HEARD_BEAT 91 |
| |
| /* |
| * This CPU module needs a baseboard to work. After basic initializing |
| * its own devices, it calls baseboard's init function. |
| * TODO: Add your own basebaord init function and call it from |
| * inside pcm027_init(). This example here is for the developmen board. |
| * Refer pcm990-baseboard.c |
| */ |
| extern void pcm990_baseboard_init(void); |
