| /* |
| * arch/arm/mach-imxads/include/mach/irqs.h |
| * |
| * Copyright (C) 1999 ARM Limited |
| * Copyright (C) 2000 Deep Blue Solutions Ltd. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| */ |
| |
| #ifndef __ARM_IRQS_H__ |
| #define __ARM_IRQS_H__ |
| |
| /* Use the imx definitions */ |
| #include <mach/hardware.h> |
| |
| /* |
| * IMX Interrupt numbers |
| * |
| */ |
| #define INT_SOFTINT 0 |
| #define CSI_INT 6 |
| #define DSPA_MAC_INT 7 |
| #define DSPA_INT 8 |
| #define COMP_INT 9 |
| #define MSHC_XINT 10 |
| #define GPIO_INT_PORTA 11 |
| #define GPIO_INT_PORTB 12 |
| #define GPIO_INT_PORTC 13 |
| #define LCDC_INT 14 |
| #define SIM_INT 15 |
| #define SIM_DATA_INT 16 |
| #define RTC_INT 17 |
| #define RTC_SAMINT 18 |
| #define UART2_MINT_PFERR 19 |
| #define UART2_MINT_RTS 20 |
| #define UART2_MINT_DTR 21 |
| #define UART2_MINT_UARTC 22 |
| #define UART2_MINT_TX 23 |
| #define UART2_MINT_RX 24 |
| #define UART1_MINT_PFERR 25 |
| #define UART1_MINT_RTS 26 |
| #define UART1_MINT_DTR 27 |
| #define UART1_MINT_UARTC 28 |
| #define UART1_MINT_TX 29 |
| #define UART1_MINT_RX 30 |
| #define VOICE_DAC_INT 31 |
| #define VOICE_ADC_INT 32 |
| #define PEN_DATA_INT 33 |
| #define PWM_INT 34 |
| #define SDHC_INT 35 |
| #define I2C_INT 39 |
| #define CSPI_INT 41 |
| #define SSI_TX_INT 42 |
| #define SSI_TX_ERR_INT 43 |
| #define SSI_RX_INT 44 |
| #define SSI_RX_ERR_INT 45 |
| #define TOUCH_INT 46 |
| #define USBD_INT0 47 |
| #define USBD_INT1 48 |
| #define USBD_INT2 49 |
| #define USBD_INT3 50 |
| #define USBD_INT4 51 |
| #define USBD_INT5 52 |
| #define USBD_INT6 53 |
| #define BTSYS_INT 55 |
| #define BTTIM_INT 56 |
| #define BTWUI_INT 57 |
| #define TIM2_INT 58 |
| #define TIM1_INT 59 |
| #define DMA_ERR 60 |
| #define DMA_INT 61 |
| #define GPIO_INT_PORTD 62 |
| |
| #define IMX_IRQS (64) |
| |
| /* note: the IMX has four gpio ports (A-D), but only |
| * the following pins are connected to the outside |
| * world: |
| * |
| * PORT A: bits 0-31 |
| * PORT B: bits 8-31 |
| * PORT C: bits 3-17 |
| * PORT D: bits 6-31 |
| * |
| * We map these interrupts straight on. As a result we have |
| * several holes in the interrupt mapping. We do this for two |
| * reasons: |
| * - mapping the interrupts without holes would get |
| * far more complicated |
| * - Motorola could well decide to bring some processor |
| * with more pins connected |
| */ |
| |
| #define IRQ_GPIOA(x) (IMX_IRQS + x) |
| #define IRQ_GPIOB(x) (IRQ_GPIOA(32) + x) |
| #define IRQ_GPIOC(x) (IRQ_GPIOB(32) + x) |
| #define IRQ_GPIOD(x) (IRQ_GPIOC(32) + x) |
| |
| /* decode irq number to use with IMR(x), ISR(x) and friends */ |
| #define IRQ_TO_REG(irq) ((irq - IMX_IRQS) >> 5) |
| |
| #define NR_IRQS (IRQ_GPIOD(32) + 1) |
| #define IRQ_GPIO(x) |
| #endif |