| # |
| # 8390 device configuration |
| # |
| |
| config NET_VENDOR_8390 |
| bool "National Semi-conductor 8390 devices" |
| depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \ |
| ISA || MCA || EISA || MAC || M32R || MACH_TX49XX || \ |
| MCA_LEGACY || H8300 || ARM || MIPS || ZORRO || PCMCIA || \ |
| EXPERIMENTAL) |
| ---help--- |
| If you have a network (Ethernet) card belonging to this class, say Y |
| and read the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| Note that the answer to this question doesn't directly affect the |
| kernel: saying N will just cause the configurator to skip all |
| the questions about Western Digital cards. If you say Y, you will be |
| asked for your specific card in the following questions. |
| |
| if NET_VENDOR_8390 |
| |
| config EL2 |
| tristate "3c503 \"EtherLink II\" support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called 3c503. |
| |
| config AC3200 |
| tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" |
| depends on PCI && (ISA || EISA) && EXPERIMENTAL |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called ac3200. |
| |
| config PCMCIA_AXNET |
| tristate "Asix AX88190 PCMCIA support" |
| depends on PCMCIA |
| ---help--- |
| Say Y here if you intend to attach an Asix AX88190-based PCMCIA |
| (PC-card) Fast Ethernet card to your computer. These cards are |
| nearly NE2000 compatible but need a separate driver due to a few |
| misfeatures. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called axnet_cs. If unsure, say N. |
| |
| config AX88796 |
| tristate "ASIX AX88796 NE2000 clone support" |
| depends on (ARM || MIPS || SUPERH) |
| select PHYLIB |
| select MDIO_BITBANG |
| ---help--- |
| AX88796 driver, using platform bus to provide |
| chip detection and resources |
| |
| config AX88796_93CX6 |
| bool "ASIX AX88796 external 93CX6 eeprom support" |
| depends on AX88796 |
| select EEPROM_93CX6 |
| ---help--- |
| Select this if your platform comes with an external 93CX6 eeprom. |
| |
| config E2100 |
| tristate "Cabletron E21xx support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called e2100. |
| |
| config ES3210 |
| tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)" |
| depends on PCI && EISA && EXPERIMENTAL |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called es3210. |
| |
| config HPLAN_PLUS |
| tristate "HP PCLAN+ (27247B and 27252A) support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called hp-plus. |
| |
| config HPLAN |
| tristate "HP PCLAN (27245 and other 27xxx series) support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called hp. |
| |
| config HYDRA |
| tristate "Hydra support" |
| depends on ZORRO |
| select CRC32 |
| ---help--- |
| If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called hydra. |
| |
| config ARM_ETHERH |
| tristate "I-cubed EtherH/ANT EtherM support" |
| depends on ARM && ARCH_ACORN |
| select CRC32 |
| ---help--- |
| If you have an Acorn system with one of these network cards, you |
| should say Y to this option if you wish to use it with Linux. |
| |
| config LNE390 |
| tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)" |
| depends on PCI && EISA && EXPERIMENTAL |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called lne390. |
| |
| config MAC8390 |
| bool "Macintosh NS 8390 based ethernet cards" |
| depends on MAC |
| select CRC32 |
| ---help--- |
| If you want to include a driver to support Nubus or LC-PDS |
| Ethernet cards using an NS8390 chipset or its equivalent, say Y |
| and read the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| config NE2000 |
| tristate "NE2000/NE1000 support" |
| depends on (ISA || (Q40 && m) || M32R || MACH_TX49XX) |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. Many Ethernet cards |
| without a specific driver are compatible with NE2000. |
| |
| If you have a PCI NE2000 card however, say N here and Y to "PCI |
| NE2000 and clone support" under "EISA, VLB, PCI and on board |
| controllers" below. If you have a NE2000 card and are running on |
| an MCA system (a bus system used on some IBM PS/2 computers and |
| laptops), say N here and Y to "NE/2 (ne2000 MCA version) support", |
| below. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called ne. |
| |
| config NE2_MCA |
| tristate "NE/2 (ne2000 MCA version) support" |
| depends on MCA_LEGACY |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called ne2. |
| |
| config NE2K_PCI |
| tristate "PCI NE2000 and clones support (see help)" |
| depends on PCI |
| select CRC32 |
| ---help--- |
| This driver is for NE2000 compatible PCI cards. It will not work |
| with ISA NE2000 cards (they have their own driver, "NE2000/NE1000 |
| support" below). If you have a PCI NE2000 network (Ethernet) card, |
| say Y and read the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| This driver also works for the following NE2000 clone cards: |
| RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2 |
| NetVin NV5000SC Via 86C926 SureCom NE34 Winbond |
| Holtek HT80232 Holtek HT80229 |
| |
| To compile this driver as a module, choose M here. The module |
| will be called ne2k-pci. |
| |
| config APNE |
| tristate "PCMCIA NE2000 support" |
| depends on AMIGA_PCMCIA |
| select CRC32 |
| ---help--- |
| If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, |
| say N. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called apne. |
| |
| config NE3210 |
| tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)" |
| depends on PCI && EISA && EXPERIMENTAL |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. Note that this driver |
| will NOT WORK for NE3200 cards as they are completely different. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called ne3210. |
| |
| config PCMCIA_PCNET |
| tristate "NE2000 compatible PCMCIA support" |
| depends on PCMCIA |
| select CRC32 |
| ---help--- |
| Say Y here if you intend to attach an NE2000 compatible PCMCIA |
| (PC-card) Ethernet or Fast Ethernet card to your computer. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called pcnet_cs. If unsure, say N. |
| |
| config NE_H8300 |
| tristate "NE2000 compatible support for H8/300" |
| depends on H8300 |
| ---help--- |
| Say Y here if you want to use the NE2000 compatible |
| controller on the Renesas H8/300 processor. |
| |
| config STNIC |
| tristate "National DP83902AV support" |
| depends on SUPERH |
| select CRC32 |
| ---help--- |
| Support for cards based on the National Semiconductor DP83902AV |
| ST-NIC Serial Network Interface Controller for Twisted Pair. This |
| is a 10Mbit/sec Ethernet controller. Product overview and specs at |
| <http://www.national.com/pf/DP/DP83902A.html>. |
| |
| If unsure, say N. |
| |
| config ULTRAMCA |
| tristate "SMC Ultra MCA support" |
| depends on MCA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type and are running |
| an MCA based system (PS/2), say Y and read the Ethernet-HOWTO, |
| available from <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called smc-mca. |
| |
| config ULTRA |
| tristate "SMC Ultra support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| Important: There have been many reports that, with some motherboards |
| mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible, |
| such as some BusLogic models) causes corruption problems with many |
| operating systems. The Linux smc-ultra driver has a work-around for |
| this but keep it in mind if you have such a SCSI card and have |
| problems. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called smc-ultra. |
| |
| config ULTRA32 |
| tristate "SMC Ultra32 EISA support" |
| depends on EISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called smc-ultra32. |
| |
| config WD80x3 |
| tristate "WD80*3 support" |
| depends on ISA |
| select CRC32 |
| ---help--- |
| If you have a network (Ethernet) card of this type, say Y and read |
| the Ethernet-HOWTO, available from |
| <http://www.tldp.org/docs.html#howto>. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called wd. |
| |
| config ZORRO8390 |
| tristate "Zorro NS8390-based Ethernet support" |
| depends on ZORRO |
| select CRC32 |
| ---help--- |
| This driver is for Zorro Ethernet cards using an NS8390-compatible |
| chipset, like the Village Tronic Ariadne II and the Individual |
| Computers X-Surf Ethernet cards. If you have such a card, say Y. |
| Otherwise, say N. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called zorro8390. |
| |
| endif # NET_VENDOR_8390 |
