| /* |
| * 6522 Versatile Interface Adapter (VIA) |
| * |
| * There are two of these on the Mac II. Some IRQ's are vectored |
| * via them as are assorted bits and bobs - eg rtc, adb. The picture |
| * is a bit incomplete as the Mac documentation doesn't cover this well |
| */ |
| |
| #ifndef _ASM_MAC_VIA_H_ |
| #define _ASM_MAC_VIA_H_ |
| |
| /* |
| * Base addresses for the VIAs. There are two in every machine, |
| * although on some machines the second is an RBV or an OSS. |
| * The OSS is different enough that it's handled separately. |
| * |
| * Do not use these values directly; use the via1 and via2 variables |
| * instead (and don't forget to check rbv_present when using via2!) |
| */ |
| |
| #define VIA1_BASE (0x50F00000) |
| #define VIA2_BASE (0x50F02000) |
| #define RBV_BASE (0x50F26000) |
| |
| /* |
| * Not all of these are true post MacII I think. |
| * CSA: probably the ones CHRP marks as 'unused' change purposes |
| * when the IWM becomes the SWIM. |
| * http://www.rs6000.ibm.com/resource/technology/chrpio/via5.mak.html |
| * ftp://ftp.austin.ibm.com/pub/technology/spec/chrp/inwork/CHRP_IORef_1.0.pdf |
| * |
| * also, http://developer.apple.com/technotes/hw/hw_09.html claims the |
| * following changes for IIfx: |
| * VIA1A_vSccWrReq not available and that VIA1A_vSync has moved to an IOP. |
| * Also, "All of the functionality of VIA2 has been moved to other chips". |
| */ |
| |
| #define VIA1A_vSccWrReq 0x80 /* SCC write. (input) |
| * [CHRP] SCC WREQ: Reflects the state of the |
| * Wait/Request pins from the SCC. |
| * [Macintosh Family Hardware] |
| * as CHRP on SE/30,II,IIx,IIcx,IIci. |
| * on IIfx, "0 means an active request" |
| */ |
| #define VIA1A_vRev8 0x40 /* Revision 8 board ??? |
| * [CHRP] En WaitReqB: Lets the WaitReq_L |
| * signal from port B of the SCC appear on |
| * the PA7 input pin. Output. |
| * [Macintosh Family] On the SE/30, this |
| * is the bit to flip screen buffers. |
| * 0=alternate, 1=main. |
| * on II,IIx,IIcx,IIci,IIfx this is a bit |
| * for Rev ID. 0=II,IIx, 1=IIcx,IIci,IIfx |
| */ |
| #define VIA1A_vHeadSel 0x20 /* Head select for IWM. |
| * [CHRP] unused. |
| * [Macintosh Family] "Floppy disk |
| * state-control line SEL" on all but IIfx |
| */ |
| #define VIA1A_vOverlay 0x10 /* [Macintosh Family] On SE/30,II,IIx,IIcx |
| * this bit enables the "Overlay" address |
| * map in the address decoders as it is on |
| * reset for mapping the ROM over the reset |
| * vector. 1=use overlay map. |
| * On the IIci,IIfx it is another bit of the |
| * CPU ID: 0=normal IIci, 1=IIci with parity |
| * feature or IIfx. |
| * [CHRP] En WaitReqA: Lets the WaitReq_L |
| * signal from port A of the SCC appear |
| * on the PA7 input pin (CHRP). Output. |
| * [MkLinux] "Drive Select" |
| * (with 0x20 being 'disk head select') |
| */ |
| #define VIA1A_vSync 0x08 /* [CHRP] Sync Modem: modem clock select: |
| * 1: select the external serial clock to |
| * drive the SCC's /RTxCA pin. |
| * 0: Select the 3.6864MHz clock to drive |
| * the SCC cell. |
| * [Macintosh Family] Correct on all but IIfx |
| */ |
| |
| /* Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control |
| * on Macs which had the PWM sound hardware. Reserved on newer models. |
| * On IIci,IIfx, bits 1-2 are the rest of the CPU ID: |
| * bit 2: 1=IIci, 0=IIfx |
| * bit 1: 1 on both IIci and IIfx. |
| * MkLinux sez bit 0 is 'burnin flag' in this case. |
| * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as |
| * inputs, these bits will read 0. |
| */ |
| #define VIA1A_vVolume 0x07 /* Audio volume mask for PWM */ |
| #define VIA1A_CPUID0 0x02 /* CPU id bit 0 on RBV, others */ |
| #define VIA1A_CPUID1 0x04 /* CPU id bit 0 on RBV, others */ |
| #define VIA1A_CPUID2 0x10 /* CPU id bit 0 on RBV, others */ |
| #define VIA1A_CPUID3 0x40 /* CPU id bit 0 on RBV, others */ |
| |
| /* Info on VIA1B is from Macintosh Family Hardware & MkLinux. |
| * CHRP offers no info. */ |
| #define VIA1B_vSound 0x80 /* Sound enable (for compatibility with |
| * PWM hardware) 0=enabled. |
| * Also, on IIci w/parity, shows parity error |
| * 0=error, 1=OK. */ |
| #define VIA1B_vMystery 0x40 /* On IIci, parity enable. 0=enabled,1=disabled |
| * On SE/30, vertical sync interrupt enable. |
| * 0=enabled. This vSync interrupt shows up |
| * as a slot $E interrupt. */ |
| #define VIA1B_vADBS2 0x20 /* ADB state input bit 1 (unused on IIfx) */ |
| #define VIA1B_vADBS1 0x10 /* ADB state input bit 0 (unused on IIfx) */ |
| #define VIA1B_vADBInt 0x08 /* ADB interrupt 0=interrupt (unused on IIfx)*/ |
| #define VIA1B_vRTCEnb 0x04 /* Enable Real time clock. 0=enabled. */ |
| #define VIA1B_vRTCClk 0x02 /* Real time clock serial-clock line. */ |
| #define VIA1B_vRTCData 0x01 /* Real time clock serial-data line. */ |
| |
| /* MkLinux defines the following "VIA1 Register B contents where they |
| * differ from standard VIA1". From the naming scheme, we assume they |
| * correspond to a VIA work-alike named 'EVR'. */ |
| #define EVRB_XCVR 0x08 /* XCVR_SESSION* */ |
| #define EVRB_FULL 0x10 /* VIA_FULL */ |
| #define EVRB_SYSES 0x20 /* SYS_SESSION */ |
| #define EVRB_AUXIE 0x00 /* Enable A/UX Interrupt Scheme */ |
| #define EVRB_AUXID 0x40 /* Disable A/UX Interrupt Scheme */ |
| #define EVRB_SFTWRIE 0x00 /* Software Interrupt ReQuest */ |
| #define EVRB_SFTWRID 0x80 /* Software Interrupt ReQuest */ |
| |
| /* |
| * VIA2 A register is the interrupt lines raised off the nubus |
| * slots. |
| * The below info is from 'Macintosh Family Hardware.' |
| * MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.' |
| * It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and |
| * defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike. |
| * Perhaps OSS uses vRAM1 and vRAM2 for ADB. |
| */ |
| |
| #define VIA2A_vRAM1 0x80 /* RAM size bit 1 (IIci: reserved) */ |
| #define VIA2A_vRAM0 0x40 /* RAM size bit 0 (IIci: internal video IRQ) */ |
| #define VIA2A_vIRQE 0x20 /* IRQ from slot $E */ |
| #define VIA2A_vIRQD 0x10 /* IRQ from slot $D */ |
| #define VIA2A_vIRQC 0x08 /* IRQ from slot $C */ |
| #define VIA2A_vIRQB 0x04 /* IRQ from slot $B */ |
| #define VIA2A_vIRQA 0x02 /* IRQ from slot $A */ |
| #define VIA2A_vIRQ9 0x01 /* IRQ from slot $9 */ |
| |
| /* RAM size bits decoded as follows: |
| * bit1 bit0 size of ICs in bank A |
| * 0 0 256 kbit |
| * 0 1 1 Mbit |
| * 1 0 4 Mbit |
| * 1 1 16 Mbit |
| */ |
| |
| /* |
| * Register B has the fun stuff in it |
| */ |
| |
| #define VIA2B_vVBL 0x80 /* VBL output to VIA1 (60.15Hz) driven by |
| * timer T1. |
| * on IIci, parity test: 0=test mode. |
| * [MkLinux] RBV_PARODD: 1=odd,0=even. */ |
| #define VIA2B_vSndJck 0x40 /* External sound jack status. |
| * 0=plug is inserted. On SE/30, always 0 */ |
| #define VIA2B_vTfr0 0x20 /* Transfer mode bit 0 ack from NuBus */ |
| #define VIA2B_vTfr1 0x10 /* Transfer mode bit 1 ack from NuBus */ |
| #define VIA2B_vMode32 0x08 /* 24/32bit switch - doubles as cache flush |
| * on II, AMU/PMMU control. |
| * if AMU, 0=24bit to 32bit translation |
| * if PMMU, 1=PMMU is accessing page table. |
| * on SE/30 tied low. |
| * on IIx,IIcx,IIfx, unused. |
| * on IIci/RBV, cache control. 0=flush cache. |
| */ |
| #define VIA2B_vPower 0x04 /* Power off, 0=shut off power. |
| * on SE/30 this signal sent to PDS card. */ |
| #define VIA2B_vBusLk 0x02 /* Lock NuBus transactions, 0=locked. |
| * on SE/30 sent to PDS card. */ |
| #define VIA2B_vCDis 0x01 /* Cache control. On IIci, 1=disable cache card |
| * on others, 0=disable processor's instruction |
| * and data caches. */ |
| |
| /* Apple sez: http://developer.apple.com/technotes/ov/ov_04.html |
| * Another example of a valid function that has no ROM support is the use |
| * of the alternate video page for page-flipping animation. Since there |
| * is no ROM call to flip pages, it is necessary to go play with the |
| * right bit in the VIA chip (6522 Versatile Interface Adapter). |
| * [CSA: don't know which one this is, but it's one of 'em!] |
| */ |
| |
| /* |
| * 6522 registers - see databook. |
| * CSA: Assignments for VIA1 confirmed from CHRP spec. |
| */ |
| |
| /* partial address decode. 0xYYXX : XX part for RBV, YY part for VIA */ |
| /* Note: 15 VIA regs, 8 RBV regs */ |
| |
| #define vBufB 0x0000 /* [VIA/RBV] Register B */ |
| #define vBufAH 0x0200 /* [VIA only] Buffer A, with handshake. DON'T USE! */ |
| #define vDirB 0x0400 /* [VIA only] Data Direction Register B. */ |
| #define vDirA 0x0600 /* [VIA only] Data Direction Register A. */ |
| #define vT1CL 0x0800 /* [VIA only] Timer one counter low. */ |
| #define vT1CH 0x0a00 /* [VIA only] Timer one counter high. */ |
| #define vT1LL 0x0c00 /* [VIA only] Timer one latches low. */ |
| #define vT1LH 0x0e00 /* [VIA only] Timer one latches high. */ |
| #define vT2CL 0x1000 /* [VIA only] Timer two counter low. */ |
| #define vT2CH 0x1200 /* [VIA only] Timer two counter high. */ |
| #define vSR 0x1400 /* [VIA only] Shift register. */ |
| #define vACR 0x1600 /* [VIA only] Auxiliary control register. */ |
| #define vPCR 0x1800 /* [VIA only] Peripheral control register. */ |
| /* CHRP sez never ever to *write* this. |
| * Mac family says never to *change* this. |
| * In fact we need to initialize it once at start. */ |
| #define vIFR 0x1a00 /* [VIA/RBV] Interrupt flag register. */ |
| #define vIER 0x1c00 /* [VIA/RBV] Interrupt enable register. */ |
| #define vBufA 0x1e00 /* [VIA/RBV] register A (no handshake) */ |
| |
| /* The RBV only decodes the bottom eight address lines; the VIA doesn't |
| * decode the bottom eight -- so vBufB | rBufB will always get you BufB */ |
| /* CSA: in fact, only bits 0,1, and 4 seem to be decoded. |
| * BUT note the values for rIER and rIFR, where the top 8 bits *do* seem |
| * to matter. In fact *all* of the top 8 bits seem to matter; |
| * setting rIER=0x1813 and rIFR=0x1803 doesn't work, either. |
| * Perhaps some sort of 'compatibility mode' is built-in? [21-May-1999] |
| */ |
| |
| #define rBufB 0x0000 /* [VIA/RBV] Register B */ |
| #define rExp 0x0001 /* [RBV only] RBV future expansion (always 0) */ |
| #define rSIFR 0x0002 /* [RBV only] RBV slot interrupts register. */ |
| #define rIFR 0x1a03 /* [VIA/RBV] RBV interrupt flag register. */ |
| #define rMonP 0x0010 /* [RBV only] RBV video monitor type. */ |
| #define rChpT 0x0011 /* [RBV only] RBV test mode register (reads as 0). */ |
| #define rSIER 0x0012 /* [RBV only] RBV slot interrupt enables. */ |
| #define rIER 0x1c13 /* [VIA/RBV] RBV interrupt flag enable register. */ |
| #define rBufA rSIFR /* the 'slot interrupts register' is BufA on a VIA */ |
| |
| /* |
| * Video monitor parameters, for rMonP: |
| */ |
| #define RBV_DEPTH 0x07 /* bits per pixel: 000=1,001=2,010=4,011=8 */ |
| #define RBV_MONID 0x38 /* monitor type, as below. */ |
| #define RBV_VIDOFF 0x40 /* 1 turns off onboard video */ |
| /* Supported monitor types: */ |
| #define MON_15BW (1<<3) /* 15" BW portrait. */ |
| #define MON_IIGS (2<<3) /* 12" color (modified IIGS monitor). */ |
| #define MON_15RGB (5<<3) /* 15" RGB portrait. */ |
| #define MON_12OR13 (6<<3) /* 12" BW or 13" RGB. */ |
| #define MON_NONE (7<<3) /* No monitor attached. */ |
| |
| /* To clarify IER manipulations */ |
| #define IER_SET_BIT(b) (0x80 | (1<<(b)) ) |
| #define IER_CLR_BIT(b) (0x7F & (1<<(b)) ) |
| |
| #ifndef __ASSEMBLY__ |
| |
| extern volatile __u8 *via1,*via2; |
| extern int rbv_present,via_alt_mapping; |
| |
| struct irq_desc; |
| |
| extern void via_register_interrupts(void); |
| extern void via_irq_enable(int); |
| extern void via_irq_disable(int); |
| extern void via_nubus_irq_startup(int irq); |
| extern void via_nubus_irq_shutdown(int irq); |
| extern void via1_irq(unsigned int irq, struct irq_desc *desc); |
| extern void via1_set_head(int); |
| extern int via2_scsi_drq_pending(void); |
| |
| static inline int rbv_set_video_bpp(int bpp) |
| { |
| char val = (bpp==1)?0:(bpp==2)?1:(bpp==4)?2:(bpp==8)?3:-1; |
| if (!rbv_present || val<0) return -1; |
| via2[rMonP] = (via2[rMonP] & ~RBV_DEPTH) | val; |
| return 0; |
| } |
| |
| #endif /* __ASSEMBLY__ */ |
| |
| #endif /* _ASM_MAC_VIA_H_ */ |
