| /* |
| * linux/arch/arm/common/gic.c |
| * |
| * Copyright (C) 2002 ARM Limited, All Rights Reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * Interrupt architecture for the GIC: |
| * |
| * o There is one Interrupt Distributor, which receives interrupts |
| * from system devices and sends them to the Interrupt Controllers. |
| * |
| * o There is one CPU Interface per CPU, which sends interrupts sent |
| * by the Distributor, and interrupts generated locally, to the |
| * associated CPU. The base address of the CPU interface is usually |
| * aliased so that the same address points to different chips depending |
| * on the CPU it is accessed from. |
| * |
| * Note that IRQs 0-31 are special - they are local to each CPU. |
| * As such, the enable set/clear, pending set/clear and active bit |
| * registers are banked per-cpu for these sources. |
| */ |
| #include <linux/init.h> |
| #include <linux/kernel.h> |
| #include <linux/list.h> |
| #include <linux/smp.h> |
| #include <linux/cpumask.h> |
| #include <linux/io.h> |
| |
| #include <asm/irq.h> |
| #include <asm/mach/irq.h> |
| #include <asm/hardware/gic.h> |
| |
| static DEFINE_SPINLOCK(irq_controller_lock); |
| |
| /* Address of GIC 0 CPU interface */ |
| void __iomem *gic_cpu_base_addr __read_mostly; |
| |
| struct gic_chip_data { |
| unsigned int irq_offset; |
| void __iomem *dist_base; |
| void __iomem *cpu_base; |
| }; |
| |
| /* |
| * Supported arch specific GIC irq extension. |
| * Default make them NULL. |
| */ |
| struct irq_chip gic_arch_extn = { |
| .irq_ack = NULL, |
| .irq_mask = NULL, |
| .irq_unmask = NULL, |
| .irq_retrigger = NULL, |
| .irq_set_type = NULL, |
| .irq_set_wake = NULL, |
| }; |
| |
| #ifndef MAX_GIC_NR |
| #define MAX_GIC_NR 1 |
| #endif |
| |
| static struct gic_chip_data gic_data[MAX_GIC_NR] __read_mostly; |
| |
| static inline void __iomem *gic_dist_base(struct irq_data *d) |
| { |
| struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); |
| return gic_data->dist_base; |
| } |
| |
| static inline void __iomem *gic_cpu_base(struct irq_data *d) |
| { |
| struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); |
| return gic_data->cpu_base; |
| } |
| |
| static inline unsigned int gic_irq(struct irq_data *d) |
| { |
| struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); |
| return d->irq - gic_data->irq_offset; |
| } |
| |
| /* |
| * Routines to acknowledge, disable and enable interrupts |
| */ |
| static void gic_ack_irq(struct irq_data *d) |
| { |
| spin_lock(&irq_controller_lock); |
| if (gic_arch_extn.irq_ack) |
| gic_arch_extn.irq_ack(d); |
| writel(gic_irq(d), gic_cpu_base(d) + GIC_CPU_EOI); |
| spin_unlock(&irq_controller_lock); |
| } |
| |
| static void gic_mask_irq(struct irq_data *d) |
| { |
| u32 mask = 1 << (d->irq % 32); |
| |
| spin_lock(&irq_controller_lock); |
| writel(mask, gic_dist_base(d) + GIC_DIST_ENABLE_CLEAR + (gic_irq(d) / 32) * 4); |
| if (gic_arch_extn.irq_mask) |
| gic_arch_extn.irq_mask(d); |
| spin_unlock(&irq_controller_lock); |
| } |
| |
| static void gic_unmask_irq(struct irq_data *d) |
| { |
| u32 mask = 1 << (d->irq % 32); |
| |
| spin_lock(&irq_controller_lock); |
| if (gic_arch_extn.irq_unmask) |
| gic_arch_extn.irq_unmask(d); |
| writel(mask, gic_dist_base(d) + GIC_DIST_ENABLE_SET + (gic_irq(d) / 32) * 4); |
| spin_unlock(&irq_controller_lock); |
| } |
| |
| static int gic_set_type(struct irq_data *d, unsigned int type) |
| { |
| void __iomem *base = gic_dist_base(d); |
| unsigned int gicirq = gic_irq(d); |
| u32 enablemask = 1 << (gicirq % 32); |
| u32 enableoff = (gicirq / 32) * 4; |
| u32 confmask = 0x2 << ((gicirq % 16) * 2); |
| u32 confoff = (gicirq / 16) * 4; |
| bool enabled = false; |
| u32 val; |
| |
| /* Interrupt configuration for SGIs can't be changed */ |
| if (gicirq < 16) |
| return -EINVAL; |
| |
| if (type != IRQ_TYPE_LEVEL_HIGH && type != IRQ_TYPE_EDGE_RISING) |
| return -EINVAL; |
| |
| spin_lock(&irq_controller_lock); |
| |
| if (gic_arch_extn.irq_set_type) |
| gic_arch_extn.irq_set_type(d, type); |
| |
| val = readl(base + GIC_DIST_CONFIG + confoff); |
| if (type == IRQ_TYPE_LEVEL_HIGH) |
| val &= ~confmask; |
| else if (type == IRQ_TYPE_EDGE_RISING) |
| val |= confmask; |
| |
| /* |
| * As recommended by the spec, disable the interrupt before changing |
| * the configuration |
| */ |
| if (readl(base + GIC_DIST_ENABLE_SET + enableoff) & enablemask) { |
| writel(enablemask, base + GIC_DIST_ENABLE_CLEAR + enableoff); |
| enabled = true; |
| } |
| |
| writel(val, base + GIC_DIST_CONFIG + confoff); |
| |
| if (enabled) |
| writel(enablemask, base + GIC_DIST_ENABLE_SET + enableoff); |
| |
| spin_unlock(&irq_controller_lock); |
| |
| return 0; |
| } |
| |
| static int gic_retrigger(struct irq_data *d) |
| { |
| if (gic_arch_extn.irq_retrigger) |
| return gic_arch_extn.irq_retrigger(d); |
| |
| return -ENXIO; |
| } |
| |
| #ifdef CONFIG_SMP |
| static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val, |
| bool force) |
| { |
| void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3); |
| unsigned int shift = (d->irq % 4) * 8; |
| unsigned int cpu = cpumask_first(mask_val); |
| u32 val, mask, bit; |
| |
| if (cpu >= 8) |
| return -EINVAL; |
| |
| mask = 0xff << shift; |
| bit = 1 << (cpu + shift); |
| |
| spin_lock(&irq_controller_lock); |
| d->node = cpu; |
| val = readl(reg) & ~mask; |
| writel(val | bit, reg); |
| spin_unlock(&irq_controller_lock); |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_PM |
| static int gic_set_wake(struct irq_data *d, unsigned int on) |
| { |
| int ret = -ENXIO; |
| |
| if (gic_arch_extn.irq_set_wake) |
| ret = gic_arch_extn.irq_set_wake(d, on); |
| |
| return ret; |
| } |
| |
| #else |
| #define gic_set_wake NULL |
| #endif |
| |
| static void gic_handle_cascade_irq(unsigned int irq, struct irq_desc *desc) |
| { |
| struct gic_chip_data *chip_data = irq_get_handler_data(irq); |
| struct irq_chip *chip = irq_get_chip(irq); |
| unsigned int cascade_irq, gic_irq; |
| unsigned long status; |
| |
| /* primary controller ack'ing */ |
| chip->irq_ack(&desc->irq_data); |
| |
| spin_lock(&irq_controller_lock); |
| status = readl(chip_data->cpu_base + GIC_CPU_INTACK); |
| spin_unlock(&irq_controller_lock); |
| |
| gic_irq = (status & 0x3ff); |
| if (gic_irq == 1023) |
| goto out; |
| |
| cascade_irq = gic_irq + chip_data->irq_offset; |
| if (unlikely(gic_irq < 32 || gic_irq > 1020 || cascade_irq >= NR_IRQS)) |
| do_bad_IRQ(cascade_irq, desc); |
| else |
| generic_handle_irq(cascade_irq); |
| |
| out: |
| /* primary controller unmasking */ |
| chip->irq_unmask(&desc->irq_data); |
| } |
| |
| static struct irq_chip gic_chip = { |
| .name = "GIC", |
| .irq_ack = gic_ack_irq, |
| .irq_mask = gic_mask_irq, |
| .irq_unmask = gic_unmask_irq, |
| .irq_set_type = gic_set_type, |
| .irq_retrigger = gic_retrigger, |
| #ifdef CONFIG_SMP |
| .irq_set_affinity = gic_set_affinity, |
| #endif |
| .irq_set_wake = gic_set_wake, |
| }; |
| |
| void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq) |
| { |
| if (gic_nr >= MAX_GIC_NR) |
| BUG(); |
| if (irq_set_handler_data(irq, &gic_data[gic_nr]) != 0) |
| BUG(); |
| irq_set_chained_handler(irq, gic_handle_cascade_irq); |
| } |
| |
| static void __init gic_dist_init(struct gic_chip_data *gic, |
| unsigned int irq_start) |
| { |
| unsigned int gic_irqs, irq_limit, i; |
| void __iomem *base = gic->dist_base; |
| u32 cpumask = 1 << smp_processor_id(); |
| |
| cpumask |= cpumask << 8; |
| cpumask |= cpumask << 16; |
| |
| writel(0, base + GIC_DIST_CTRL); |
| |
| /* |
| * Find out how many interrupts are supported. |
| * The GIC only supports up to 1020 interrupt sources. |
| */ |
| gic_irqs = readl(base + GIC_DIST_CTR) & 0x1f; |
| gic_irqs = (gic_irqs + 1) * 32; |
| if (gic_irqs > 1020) |
| gic_irqs = 1020; |
| |
| /* |
| * Set all global interrupts to be level triggered, active low. |
| */ |
| for (i = 32; i < gic_irqs; i += 16) |
| writel(0, base + GIC_DIST_CONFIG + i * 4 / 16); |
| |
| /* |
| * Set all global interrupts to this CPU only. |
| */ |
| for (i = 32; i < gic_irqs; i += 4) |
| writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4); |
| |
| /* |
| * Set priority on all global interrupts. |
| */ |
| for (i = 32; i < gic_irqs; i += 4) |
| writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4); |
| |
| /* |
| * Disable all interrupts. Leave the PPI and SGIs alone |
| * as these enables are banked registers. |
| */ |
| for (i = 32; i < gic_irqs; i += 32) |
| writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32); |
| |
| /* |
| * Limit number of interrupts registered to the platform maximum |
| */ |
| irq_limit = gic->irq_offset + gic_irqs; |
| if (WARN_ON(irq_limit > NR_IRQS)) |
| irq_limit = NR_IRQS; |
| |
| /* |
| * Setup the Linux IRQ subsystem. |
| */ |
| for (i = irq_start; i < irq_limit; i++) { |
| irq_set_chip_and_handler(i, &gic_chip, handle_level_irq); |
| irq_set_chip_data(i, gic); |
| set_irq_flags(i, IRQF_VALID | IRQF_PROBE); |
| } |
| |
| writel(1, base + GIC_DIST_CTRL); |
| } |
| |
| static void __cpuinit gic_cpu_init(struct gic_chip_data *gic) |
| { |
| void __iomem *dist_base = gic->dist_base; |
| void __iomem *base = gic->cpu_base; |
| int i; |
| |
| /* |
| * Deal with the banked PPI and SGI interrupts - disable all |
| * PPI interrupts, ensure all SGI interrupts are enabled. |
| */ |
| writel(0xffff0000, dist_base + GIC_DIST_ENABLE_CLEAR); |
| writel(0x0000ffff, dist_base + GIC_DIST_ENABLE_SET); |
| |
| /* |
| * Set priority on PPI and SGI interrupts |
| */ |
| for (i = 0; i < 32; i += 4) |
| writel(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4 / 4); |
| |
| writel(0xf0, base + GIC_CPU_PRIMASK); |
| writel(1, base + GIC_CPU_CTRL); |
| } |
| |
| void __init gic_init(unsigned int gic_nr, unsigned int irq_start, |
| void __iomem *dist_base, void __iomem *cpu_base) |
| { |
| struct gic_chip_data *gic; |
| |
| BUG_ON(gic_nr >= MAX_GIC_NR); |
| |
| gic = &gic_data[gic_nr]; |
| gic->dist_base = dist_base; |
| gic->cpu_base = cpu_base; |
| gic->irq_offset = (irq_start - 1) & ~31; |
| |
| if (gic_nr == 0) |
| gic_cpu_base_addr = cpu_base; |
| |
| gic_dist_init(gic, irq_start); |
| gic_cpu_init(gic); |
| } |
| |
| void __cpuinit gic_secondary_init(unsigned int gic_nr) |
| { |
| BUG_ON(gic_nr >= MAX_GIC_NR); |
| |
| gic_cpu_init(&gic_data[gic_nr]); |
| } |
| |
| void __cpuinit gic_enable_ppi(unsigned int irq) |
| { |
| unsigned long flags; |
| |
| local_irq_save(flags); |
| irq_set_status_flags(irq, IRQ_NOPROBE); |
| gic_unmask_irq(irq_get_irq_data(irq)); |
| local_irq_restore(flags); |
| } |
| |
| #ifdef CONFIG_SMP |
| void gic_raise_softirq(const struct cpumask *mask, unsigned int irq) |
| { |
| unsigned long map = *cpus_addr(*mask); |
| |
| /* this always happens on GIC0 */ |
| writel(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT); |
| } |
| #endif |