| /* |
| * Device Tree Source for OMAP3 SoC |
| * |
| * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/pinctrl/omap.h> |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| compatible = "ti,omap3430", "ti,omap3"; |
| interrupt-parent = <&intc>; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| compatible = "arm,cortex-a8"; |
| device_type = "cpu"; |
| reg = <0x0>; |
| |
| clocks = <&dpll1_ck>; |
| clock-names = "cpu"; |
| |
| clock-latency = <300000>; /* From omap-cpufreq driver */ |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a8-pmu"; |
| reg = <0x54000000 0x800000>; |
| interrupts = <3>; |
| ti,hwmods = "debugss"; |
| }; |
| |
| /* |
| * The soc node represents the soc top level view. It is used for IPs |
| * that are not memory mapped in the MPU view or for the MPU itself. |
| */ |
| soc { |
| compatible = "ti,omap-infra"; |
| mpu { |
| compatible = "ti,omap3-mpu"; |
| ti,hwmods = "mpu"; |
| }; |
| |
| iva { |
| compatible = "ti,iva2.2"; |
| ti,hwmods = "iva"; |
| |
| dsp { |
| compatible = "ti,omap3-c64"; |
| }; |
| }; |
| }; |
| |
| /* |
| * XXX: Use a flat representation of the OMAP3 interconnect. |
| * The real OMAP interconnect network is quite complex. |
| * Since that will not bring real advantage to represent that in DT for |
| * the moment, just use a fake OCP bus entry to represent the whole bus |
| * hierarchy. |
| */ |
| ocp { |
| compatible = "simple-bus"; |
| reg = <0x68000000 0x10000>; |
| interrupts = <9 10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main"; |
| |
| aes: aes@480c5000 { |
| compatible = "ti,omap3-aes"; |
| ti,hwmods = "aes"; |
| reg = <0x480c5000 0x50>; |
| interrupts = <0>; |
| }; |
| |
| prm: prm@48306000 { |
| compatible = "ti,omap3-prm"; |
| reg = <0x48306000 0x4000>; |
| |
| prm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| prm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| cm: cm@48004000 { |
| compatible = "ti,omap3-cm"; |
| reg = <0x48004000 0x4000>; |
| |
| cm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| cm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| scrm: scrm@48002000 { |
| compatible = "ti,omap3-scrm"; |
| reg = <0x48002000 0x2000>; |
| |
| scrm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| scrm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| counter32k: counter@48320000 { |
| compatible = "ti,omap-counter32k"; |
| reg = <0x48320000 0x20>; |
| ti,hwmods = "counter_32k"; |
| }; |
| |
| intc: interrupt-controller@48200000 { |
| compatible = "ti,omap2-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| ti,intc-size = <96>; |
| reg = <0x48200000 0x1000>; |
| }; |
| |
| sdma: dma-controller@48056000 { |
| compatible = "ti,omap3630-sdma", "ti,omap3430-sdma"; |
| reg = <0x48056000 0x1000>; |
| interrupts = <12>, |
| <13>, |
| <14>, |
| <15>; |
| #dma-cells = <1>; |
| #dma-channels = <32>; |
| #dma-requests = <96>; |
| }; |
| |
| omap3_pmx_core: pinmux@48002030 { |
| compatible = "ti,omap3-padconf", "pinctrl-single"; |
| reg = <0x48002030 0x0238>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <16>; |
| pinctrl-single,function-mask = <0xff1f>; |
| }; |
| |
| omap3_pmx_wkup: pinmux@48002a00 { |
| compatible = "ti,omap3-padconf", "pinctrl-single"; |
| reg = <0x48002a00 0x5c>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <16>; |
| pinctrl-single,function-mask = <0xff1f>; |
| }; |
| |
| omap3_scm_general: tisyscon@48002270 { |
| compatible = "syscon"; |
| reg = <0x48002270 0x2f0>; |
| }; |
| |
| pbias_regulator: pbias_regulator { |
| compatible = "ti,pbias-omap"; |
| reg = <0x2b0 0x4>; |
| syscon = <&omap3_scm_general>; |
| pbias_mmc_reg: pbias_mmc_omap2430 { |
| regulator-name = "pbias_mmc_omap2430"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| }; |
| |
| gpio1: gpio@48310000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x48310000 0x200>; |
| interrupts = <29>; |
| ti,hwmods = "gpio1"; |
| ti,gpio-always-on; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@49050000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x49050000 0x200>; |
| interrupts = <30>; |
| ti,hwmods = "gpio2"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@49052000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x49052000 0x200>; |
| interrupts = <31>; |
| ti,hwmods = "gpio3"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@49054000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x49054000 0x200>; |
| interrupts = <32>; |
| ti,hwmods = "gpio4"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@49056000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x49056000 0x200>; |
| interrupts = <33>; |
| ti,hwmods = "gpio5"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@49058000 { |
| compatible = "ti,omap3-gpio"; |
| reg = <0x49058000 0x200>; |
| interrupts = <34>; |
| ti,hwmods = "gpio6"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| uart1: serial@4806a000 { |
| compatible = "ti,omap3-uart"; |
| reg = <0x4806a000 0x2000>; |
| interrupts = <72>; |
| dmas = <&sdma 49 &sdma 50>; |
| dma-names = "tx", "rx"; |
| ti,hwmods = "uart1"; |
| clock-frequency = <48000000>; |
| }; |
| |
| uart2: serial@4806c000 { |
| compatible = "ti,omap3-uart"; |
| reg = <0x4806c000 0x400>; |
| interrupts = <73>; |
| dmas = <&sdma 51 &sdma 52>; |
| dma-names = "tx", "rx"; |
| ti,hwmods = "uart2"; |
| clock-frequency = <48000000>; |
| }; |
| |
| uart3: serial@49020000 { |
| compatible = "ti,omap3-uart"; |
| reg = <0x49020000 0x400>; |
| interrupts = <74>; |
| dmas = <&sdma 53 &sdma 54>; |
| dma-names = "tx", "rx"; |
| ti,hwmods = "uart3"; |
| clock-frequency = <48000000>; |
| }; |
| |
| i2c1: i2c@48070000 { |
| compatible = "ti,omap3-i2c"; |
| reg = <0x48070000 0x80>; |
| interrupts = <56>; |
| dmas = <&sdma 27 &sdma 28>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c1"; |
| }; |
| |
| i2c2: i2c@48072000 { |
| compatible = "ti,omap3-i2c"; |
| reg = <0x48072000 0x80>; |
| interrupts = <57>; |
| dmas = <&sdma 29 &sdma 30>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c2"; |
| }; |
| |
| i2c3: i2c@48060000 { |
| compatible = "ti,omap3-i2c"; |
| reg = <0x48060000 0x80>; |
| interrupts = <61>; |
| dmas = <&sdma 25 &sdma 26>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c3"; |
| }; |
| |
| mailbox: mailbox@48094000 { |
| compatible = "ti,omap3-mailbox"; |
| ti,hwmods = "mailbox"; |
| reg = <0x48094000 0x200>; |
| interrupts = <26>; |
| }; |
| |
| mcspi1: spi@48098000 { |
| compatible = "ti,omap2-mcspi"; |
| reg = <0x48098000 0x100>; |
| interrupts = <65>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi1"; |
| ti,spi-num-cs = <4>; |
| dmas = <&sdma 35>, |
| <&sdma 36>, |
| <&sdma 37>, |
| <&sdma 38>, |
| <&sdma 39>, |
| <&sdma 40>, |
| <&sdma 41>, |
| <&sdma 42>; |
| dma-names = "tx0", "rx0", "tx1", "rx1", |
| "tx2", "rx2", "tx3", "rx3"; |
| }; |
| |
| mcspi2: spi@4809a000 { |
| compatible = "ti,omap2-mcspi"; |
| reg = <0x4809a000 0x100>; |
| interrupts = <66>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi2"; |
| ti,spi-num-cs = <2>; |
| dmas = <&sdma 43>, |
| <&sdma 44>, |
| <&sdma 45>, |
| <&sdma 46>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| }; |
| |
| mcspi3: spi@480b8000 { |
| compatible = "ti,omap2-mcspi"; |
| reg = <0x480b8000 0x100>; |
| interrupts = <91>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi3"; |
| ti,spi-num-cs = <2>; |
| dmas = <&sdma 15>, |
| <&sdma 16>, |
| <&sdma 23>, |
| <&sdma 24>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| }; |
| |
| mcspi4: spi@480ba000 { |
| compatible = "ti,omap2-mcspi"; |
| reg = <0x480ba000 0x100>; |
| interrupts = <48>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi4"; |
| ti,spi-num-cs = <1>; |
| dmas = <&sdma 70>, <&sdma 71>; |
| dma-names = "tx0", "rx0"; |
| }; |
| |
| hdqw1w: 1w@480b2000 { |
| compatible = "ti,omap3-1w"; |
| reg = <0x480b2000 0x1000>; |
| interrupts = <58>; |
| ti,hwmods = "hdq1w"; |
| }; |
| |
| mmc1: mmc@4809c000 { |
| compatible = "ti,omap3-hsmmc"; |
| reg = <0x4809c000 0x200>; |
| interrupts = <83>; |
| ti,hwmods = "mmc1"; |
| ti,dual-volt; |
| dmas = <&sdma 61>, <&sdma 62>; |
| dma-names = "tx", "rx"; |
| pbias-supply = <&pbias_mmc_reg>; |
| }; |
| |
| mmc2: mmc@480b4000 { |
| compatible = "ti,omap3-hsmmc"; |
| reg = <0x480b4000 0x200>; |
| interrupts = <86>; |
| ti,hwmods = "mmc2"; |
| dmas = <&sdma 47>, <&sdma 48>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmc3: mmc@480ad000 { |
| compatible = "ti,omap3-hsmmc"; |
| reg = <0x480ad000 0x200>; |
| interrupts = <94>; |
| ti,hwmods = "mmc3"; |
| dmas = <&sdma 77>, <&sdma 78>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmu_isp: mmu@480bd400 { |
| compatible = "ti,omap2-iommu"; |
| reg = <0x480bd400 0x80>; |
| interrupts = <24>; |
| ti,hwmods = "mmu_isp"; |
| ti,#tlb-entries = <8>; |
| }; |
| |
| mmu_iva: mmu@5d000000 { |
| compatible = "ti,omap2-iommu"; |
| reg = <0x5d000000 0x80>; |
| interrupts = <28>; |
| ti,hwmods = "mmu_iva"; |
| status = "disabled"; |
| }; |
| |
| wdt2: wdt@48314000 { |
| compatible = "ti,omap3-wdt"; |
| reg = <0x48314000 0x80>; |
| ti,hwmods = "wd_timer2"; |
| }; |
| |
| mcbsp1: mcbsp@48074000 { |
| compatible = "ti,omap3-mcbsp"; |
| reg = <0x48074000 0xff>; |
| reg-names = "mpu"; |
| interrupts = <16>, /* OCP compliant interrupt */ |
| <59>, /* TX interrupt */ |
| <60>; /* RX interrupt */ |
| interrupt-names = "common", "tx", "rx"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp1"; |
| dmas = <&sdma 31>, |
| <&sdma 32>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp2: mcbsp@49022000 { |
| compatible = "ti,omap3-mcbsp"; |
| reg = <0x49022000 0xff>, |
| <0x49028000 0xff>; |
| reg-names = "mpu", "sidetone"; |
| interrupts = <17>, /* OCP compliant interrupt */ |
| <62>, /* TX interrupt */ |
| <63>, /* RX interrupt */ |
| <4>; /* Sidetone */ |
| interrupt-names = "common", "tx", "rx", "sidetone"; |
| ti,buffer-size = <1280>; |
| ti,hwmods = "mcbsp2", "mcbsp2_sidetone"; |
| dmas = <&sdma 33>, |
| <&sdma 34>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp3: mcbsp@49024000 { |
| compatible = "ti,omap3-mcbsp"; |
| reg = <0x49024000 0xff>, |
| <0x4902a000 0xff>; |
| reg-names = "mpu", "sidetone"; |
| interrupts = <22>, /* OCP compliant interrupt */ |
| <89>, /* TX interrupt */ |
| <90>, /* RX interrupt */ |
| <5>; /* Sidetone */ |
| interrupt-names = "common", "tx", "rx", "sidetone"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp3", "mcbsp3_sidetone"; |
| dmas = <&sdma 17>, |
| <&sdma 18>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp4: mcbsp@49026000 { |
| compatible = "ti,omap3-mcbsp"; |
| reg = <0x49026000 0xff>; |
| reg-names = "mpu"; |
| interrupts = <23>, /* OCP compliant interrupt */ |
| <54>, /* TX interrupt */ |
| <55>; /* RX interrupt */ |
| interrupt-names = "common", "tx", "rx"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp4"; |
| dmas = <&sdma 19>, |
| <&sdma 20>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp5: mcbsp@48096000 { |
| compatible = "ti,omap3-mcbsp"; |
| reg = <0x48096000 0xff>; |
| reg-names = "mpu"; |
| interrupts = <27>, /* OCP compliant interrupt */ |
| <81>, /* TX interrupt */ |
| <82>; /* RX interrupt */ |
| interrupt-names = "common", "tx", "rx"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp5"; |
| dmas = <&sdma 21>, |
| <&sdma 22>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| sham: sham@480c3000 { |
| compatible = "ti,omap3-sham"; |
| ti,hwmods = "sham"; |
| reg = <0x480c3000 0x64>; |
| interrupts = <49>; |
| }; |
| |
| smartreflex_core: smartreflex@480cb000 { |
| compatible = "ti,omap3-smartreflex-core"; |
| ti,hwmods = "smartreflex_core"; |
| reg = <0x480cb000 0x400>; |
| interrupts = <19>; |
| }; |
| |
| smartreflex_mpu_iva: smartreflex@480c9000 { |
| compatible = "ti,omap3-smartreflex-iva"; |
| ti,hwmods = "smartreflex_mpu_iva"; |
| reg = <0x480c9000 0x400>; |
| interrupts = <18>; |
| }; |
| |
| timer1: timer@48318000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48318000 0x400>; |
| interrupts = <37>; |
| ti,hwmods = "timer1"; |
| ti,timer-alwon; |
| }; |
| |
| timer2: timer@49032000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x49032000 0x400>; |
| interrupts = <38>; |
| ti,hwmods = "timer2"; |
| }; |
| |
| timer3: timer@49034000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x49034000 0x400>; |
| interrupts = <39>; |
| ti,hwmods = "timer3"; |
| }; |
| |
| timer4: timer@49036000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x49036000 0x400>; |
| interrupts = <40>; |
| ti,hwmods = "timer4"; |
| }; |
| |
| timer5: timer@49038000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x49038000 0x400>; |
| interrupts = <41>; |
| ti,hwmods = "timer5"; |
| ti,timer-dsp; |
| }; |
| |
| timer6: timer@4903a000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x4903a000 0x400>; |
| interrupts = <42>; |
| ti,hwmods = "timer6"; |
| ti,timer-dsp; |
| }; |
| |
| timer7: timer@4903c000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x4903c000 0x400>; |
| interrupts = <43>; |
| ti,hwmods = "timer7"; |
| ti,timer-dsp; |
| }; |
| |
| timer8: timer@4903e000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x4903e000 0x400>; |
| interrupts = <44>; |
| ti,hwmods = "timer8"; |
| ti,timer-pwm; |
| ti,timer-dsp; |
| }; |
| |
| timer9: timer@49040000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x49040000 0x400>; |
| interrupts = <45>; |
| ti,hwmods = "timer9"; |
| ti,timer-pwm; |
| }; |
| |
| timer10: timer@48086000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48086000 0x400>; |
| interrupts = <46>; |
| ti,hwmods = "timer10"; |
| ti,timer-pwm; |
| }; |
| |
| timer11: timer@48088000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48088000 0x400>; |
| interrupts = <47>; |
| ti,hwmods = "timer11"; |
| ti,timer-pwm; |
| }; |
| |
| timer12: timer@48304000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48304000 0x400>; |
| interrupts = <95>; |
| ti,hwmods = "timer12"; |
| ti,timer-alwon; |
| ti,timer-secure; |
| }; |
| |
| usbhstll: usbhstll@48062000 { |
| compatible = "ti,usbhs-tll"; |
| reg = <0x48062000 0x1000>; |
| interrupts = <78>; |
| ti,hwmods = "usb_tll_hs"; |
| }; |
| |
| usbhshost: usbhshost@48064000 { |
| compatible = "ti,usbhs-host"; |
| reg = <0x48064000 0x400>; |
| ti,hwmods = "usb_host_hs"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| usbhsohci: ohci@48064400 { |
| compatible = "ti,ohci-omap3"; |
| reg = <0x48064400 0x400>; |
| interrupt-parent = <&intc>; |
| interrupts = <76>; |
| }; |
| |
| usbhsehci: ehci@48064800 { |
| compatible = "ti,ehci-omap"; |
| reg = <0x48064800 0x400>; |
| interrupt-parent = <&intc>; |
| interrupts = <77>; |
| }; |
| }; |
| |
| gpmc: gpmc@6e000000 { |
| compatible = "ti,omap3430-gpmc"; |
| ti,hwmods = "gpmc"; |
| reg = <0x6e000000 0x02d0>; |
| interrupts = <20>; |
| gpmc,num-cs = <8>; |
| gpmc,num-waitpins = <4>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| }; |
| |
| usb_otg_hs: usb_otg_hs@480ab000 { |
| compatible = "ti,omap3-musb"; |
| reg = <0x480ab000 0x1000>; |
| interrupts = <92>, <93>; |
| interrupt-names = "mc", "dma"; |
| ti,hwmods = "usb_otg_hs"; |
| multipoint = <1>; |
| num-eps = <16>; |
| ram-bits = <12>; |
| }; |
| |
| dss: dss@48050000 { |
| compatible = "ti,omap3-dss"; |
| reg = <0x48050000 0x200>; |
| status = "disabled"; |
| ti,hwmods = "dss_core"; |
| clocks = <&dss1_alwon_fck>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| dispc@48050400 { |
| compatible = "ti,omap3-dispc"; |
| reg = <0x48050400 0x400>; |
| interrupts = <25>; |
| ti,hwmods = "dss_dispc"; |
| clocks = <&dss1_alwon_fck>; |
| clock-names = "fck"; |
| }; |
| |
| dsi: encoder@4804fc00 { |
| compatible = "ti,omap3-dsi"; |
| reg = <0x4804fc00 0x200>, |
| <0x4804fe00 0x40>, |
| <0x4804ff00 0x20>; |
| reg-names = "proto", "phy", "pll"; |
| interrupts = <25>; |
| status = "disabled"; |
| ti,hwmods = "dss_dsi1"; |
| clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| |
| rfbi: encoder@48050800 { |
| compatible = "ti,omap3-rfbi"; |
| reg = <0x48050800 0x100>; |
| status = "disabled"; |
| ti,hwmods = "dss_rfbi"; |
| clocks = <&dss1_alwon_fck>, <&dss_ick>; |
| clock-names = "fck", "ick"; |
| }; |
| |
| venc: encoder@48050c00 { |
| compatible = "ti,omap3-venc"; |
| reg = <0x48050c00 0x100>; |
| status = "disabled"; |
| ti,hwmods = "dss_venc"; |
| clocks = <&dss_tv_fck>; |
| clock-names = "fck"; |
| }; |
| }; |
| }; |
| }; |
| |
| /include/ "omap3xxx-clocks.dtsi" |
