| /* |
| * Copyright 2013 Data Modul AG |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include "imx6q.dtsi" |
| |
| / { |
| model = "Data Modul eDM-QMX6 Board"; |
| compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q"; |
| |
| aliases { |
| gpio7 = &stmpe_gpio; |
| }; |
| |
| memory { |
| reg = <0x10000000 0x80000000>; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reg_3p3v: regulator@0 { |
| compatible = "regulator-fixed"; |
| reg = <0>; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_otg_vbus: regulator@1 { |
| compatible = "regulator-fixed"; |
| reg = <1>; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio7 12 0>; |
| }; |
| |
| reg_usb_host1: regulator@2 { |
| compatible = "regulator-fixed"; |
| reg = <2>; |
| regulator-name = "usb_host1_en"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio3 31 0>; |
| enable-active-high; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| led-blue { |
| label = "blue"; |
| gpios = <&stmpe_gpio 8 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led-green { |
| label = "green"; |
| gpios = <&stmpe_gpio 9 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| led-pink { |
| label = "pink"; |
| gpios = <&stmpe_gpio 10 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| led-red { |
| label = "red"; |
| gpios = <&stmpe_gpio 11 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet>; |
| phy-mode = "rgmii"; |
| phy-reset-gpios = <&gpio3 23 0>; |
| phy-supply = <&vgen2_1v2_eth>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2 |
| &pinctrl_stmpe>; |
| status = "okay"; |
| |
| pmic: pfuze100@08 { |
| compatible = "fsl,pfuze100"; |
| reg = <0x08>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <20 8>; |
| |
| regulators { |
| sw1a_reg: sw1ab { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw1c_reg: sw1c { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3a_reg: sw3a { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3b_reg: sw3b { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-always-on; |
| }; |
| |
| swbst_reg: swbst { |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5150000>; |
| regulator-always-on; |
| }; |
| |
| snvs_reg: vsnvs { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vref_reg: vrefddr { |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen2_1v2_eth: vgen2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vdd_high_in: vgen3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vgen4_reg: vgen4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen5_reg: vgen5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen6_reg: vgen6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| stmpe: stmpe1601@40 { |
| compatible = "st,stmpe1601"; |
| reg = <0x40>; |
| interrupts = <30 0>; |
| interrupt-parent = <&gpio3>; |
| |
| stmpe_gpio: stmpe_gpio { |
| #gpio-cells = <2>; |
| compatible = "st,stmpe-gpio"; |
| }; |
| }; |
| |
| temp1: ad7414@4c { |
| compatible = "ad,ad7414"; |
| reg = <0x4c>; |
| }; |
| |
| temp2: ad7414@4d { |
| compatible = "ad,ad7414"; |
| reg = <0x4d>; |
| }; |
| |
| rtc: m41t62@68 { |
| compatible = "stm,m41t62"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| imx6q-dmo-edmqmx6 { |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000 |
| MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000 |
| >; |
| }; |
| |
| pinctrl_enet: enetgrp { |
| fsl,pins = < |
| MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 |
| MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 |
| MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 |
| MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 |
| MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 |
| MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 |
| MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 |
| MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 |
| MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 |
| MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 |
| MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 |
| MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 |
| MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 |
| MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 |
| MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 |
| MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_stmpe: stmpegrp { |
| fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 |
| >; |
| }; |
| |
| pinctrl_usdhc4: usdhc4grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 |
| MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 |
| MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 |
| MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 |
| MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 |
| MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 |
| MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 |
| MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 |
| MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 |
| MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 |
| >; |
| }; |
| }; |
| }; |
| |
| &sata { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_host1>; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| vmmc-supply = <®_3p3v>; |
| status = "okay"; |
| }; |
| |
| &usdhc4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc4>; |
| vmmc-supply = <®_3p3v>; |
| non-removable; |
| bus-width = <8>; |
| status = "okay"; |
| }; |
