blob: 8d8c80e3656d6ebaf36c71dfc0351dbe28efe5b3 [file] [log] [blame]
/dts-v1/;
#include "kirkwood.dtsi"
#include "kirkwood-6281.dtsi"
/ {
model = "Iomega Iconnect";
compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
linux,initrd-start = <0x4500040>;
linux,initrd-end = <0x4800000>;
};
mbus {
pcie-controller {
status = "okay";
pcie@1,0 {
status = "okay";
};
};
};
ocp@f1000000 {
pinctrl: pinctrl@10000 {
pmx_button_reset: pmx-button-reset {
marvell,pins = "mpp12";
marvell,function = "gpio";
};
pmx_button_otb: pmx-button-otb {
marvell,pins = "mpp35";
marvell,function = "gpio";
};
pmx_led_level: pmx-led-level {
marvell,pins = "mpp41";
marvell,function = "gpio";
};
pmx_led_power_blue: pmx-led-power-blue {
marvell,pins = "mpp42";
marvell,function = "gpio";
};
pmx_led_power_red: pmx-power-red {
marvell,pins = "mpp43";
marvell,function = "gpio";
};
pmx_led_usb1: pmx-led-usb1 {
marvell,pins = "mpp44";
marvell,function = "gpio";
};
pmx_led_usb2: pmx-led-usb2 {
marvell,pins = "mpp45";
marvell,function = "gpio";
};
pmx_led_usb3: pmx-led-usb3 {
marvell,pins = "mpp46";
marvell,function = "gpio";
};
pmx_led_usb4: pmx-led-usb4 {
marvell,pins = "mpp47";
marvell,function = "gpio";
};
pmx_led_otb: pmx-led-otb {
marvell,pins = "mpp48";
marvell,function = "gpio";
};
};
i2c@11000 {
status = "okay";
lm63: lm63@4c {
compatible = "national,lm63";
reg = <0x4c>;
};
};
serial@12000 {
status = "ok";
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = < &pmx_led_level &pmx_led_power_blue
&pmx_led_power_red &pmx_led_usb1
&pmx_led_usb2 &pmx_led_usb3
&pmx_led_usb4 &pmx_led_otb >;
pinctrl-names = "default";
led-level {
label = "led_level";
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
power-blue {
label = "power:blue";
gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
default-state = "keep";
};
power-red {
label = "power:red";
gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
};
usb1 {
label = "usb1:blue";
gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
};
usb2 {
label = "usb2:blue";
gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
};
usb3 {
label = "usb3:blue";
gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
};
usb4 {
label = "usb4:blue";
gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
};
otb {
label = "otb:blue";
gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = < &pmx_button_reset &pmx_button_otb >;
pinctrl-names = "default";
button@1 {
label = "OTB Button";
linux,code = <KEY_COPY>;
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
debounce-interval = <100>;
};
button@2 {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
debounce-interval = <100>;
};
};
};
&nand {
status = "okay";
partition@0 {
label = "uboot";
reg = <0x0000000 0xc0000>;
};
partition@a0000 {
label = "env";
reg = <0xa0000 0x20000>;
};
partition@100000 {
label = "zImage";
reg = <0x100000 0x300000>;
};
partition@540000 {
label = "initrd";
reg = <0x540000 0x300000>;
};
partition@980000 {
label = "boot";
reg = <0x980000 0x1f400000>;
};
};
&mdio {
status = "okay";
ethphy0: ethernet-phy@11 {
reg = <11>;
};
};
&eth0 {
status = "okay";
ethernet0-port@0 {
phy-handle = <&ethphy0>;
};
};