| /* |
| * linux/drivers/ide/pci/ns87415.c Version 2.00 Sep. 10, 2002 |
| * |
| * Copyright (C) 1997-1998 Mark Lord <mlord@pobox.com> |
| * Copyright (C) 1998 Eddie C. Dost <ecd@skynet.be> |
| * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org> |
| * Copyright (C) 2004 Grant Grundler <grundler at parisc-linux.org> |
| * |
| * Inspired by an earlier effort from David S. Miller <davem@redhat.com> |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/types.h> |
| #include <linux/kernel.h> |
| #include <linux/timer.h> |
| #include <linux/mm.h> |
| #include <linux/ioport.h> |
| #include <linux/interrupt.h> |
| #include <linux/blkdev.h> |
| #include <linux/hdreg.h> |
| #include <linux/pci.h> |
| #include <linux/delay.h> |
| #include <linux/ide.h> |
| #include <linux/init.h> |
| |
| #include <asm/io.h> |
| |
| #ifdef CONFIG_SUPERIO |
| /* SUPERIO 87560 is a PoS chip that NatSem denies exists. |
| * Unfortunately, it's built-in on all Astro-based PA-RISC workstations |
| * which use the integrated NS87514 cell for CD-ROM support. |
| * i.e we have to support for CD-ROM installs. |
| * See drivers/parisc/superio.c for more gory details. |
| */ |
| #include <asm/superio.h> |
| |
| static unsigned long superio_ide_status[2]; |
| static unsigned long superio_ide_select[2]; |
| static unsigned long superio_ide_dma_status[2]; |
| |
| #define SUPERIO_IDE_MAX_RETRIES 25 |
| |
| /* Because of a defect in Super I/O, all reads of the PCI DMA status |
| * registers, IDE status register and the IDE select register need to be |
| * retried |
| */ |
| static u8 superio_ide_inb (unsigned long port) |
| { |
| if (port == superio_ide_status[0] || |
| port == superio_ide_status[1] || |
| port == superio_ide_select[0] || |
| port == superio_ide_select[1] || |
| port == superio_ide_dma_status[0] || |
| port == superio_ide_dma_status[1]) { |
| u8 tmp; |
| int retries = SUPERIO_IDE_MAX_RETRIES; |
| |
| /* printk(" [ reading port 0x%x with retry ] ", port); */ |
| |
| do { |
| tmp = inb(port); |
| if (tmp == 0) |
| udelay(50); |
| } while (tmp == 0 && retries-- > 0); |
| |
| return tmp; |
| } |
| |
| return inb(port); |
| } |
| |
| static void __devinit superio_ide_init_iops (struct hwif_s *hwif) |
| { |
| u32 base, dmabase; |
| u8 tmp; |
| struct pci_dev *pdev = hwif->pci_dev; |
| u8 port = hwif->channel; |
| |
| base = pci_resource_start(pdev, port * 2) & ~3; |
| dmabase = pci_resource_start(pdev, 4) & ~3; |
| |
| superio_ide_status[port] = base + IDE_STATUS_OFFSET; |
| superio_ide_select[port] = base + IDE_SELECT_OFFSET; |
| superio_ide_dma_status[port] = dmabase + (!port ? 2 : 0xa); |
| |
| /* Clear error/interrupt, enable dma */ |
| tmp = superio_ide_inb(superio_ide_dma_status[port]); |
| outb(tmp | 0x66, superio_ide_dma_status[port]); |
| |
| /* We need to override inb to workaround a SuperIO errata */ |
| hwif->INB = superio_ide_inb; |
| } |
| |
| static void __devinit init_iops_ns87415(ide_hwif_t *hwif) |
| { |
| if (PCI_SLOT(hwif->pci_dev->devfn) == 0xE) { |
| /* Built-in - assume it's under superio. */ |
| superio_ide_init_iops(hwif); |
| } |
| } |
| #endif |
| |
| static unsigned int ns87415_count = 0, ns87415_control[MAX_HWIFS] = { 0 }; |
| |
| /* |
| * This routine either enables/disables (according to drive->present) |
| * the IRQ associated with the port (HWIF(drive)), |
| * and selects either PIO or DMA handshaking for the next I/O operation. |
| */ |
| static void ns87415_prepare_drive (ide_drive_t *drive, unsigned int use_dma) |
| { |
| ide_hwif_t *hwif = HWIF(drive); |
| unsigned int bit, other, new, *old = (unsigned int *) hwif->select_data; |
| struct pci_dev *dev = hwif->pci_dev; |
| unsigned long flags; |
| |
| local_irq_save(flags); |
| new = *old; |
| |
| /* Adjust IRQ enable bit */ |
| bit = 1 << (8 + hwif->channel); |
| new = drive->present ? (new & ~bit) : (new | bit); |
| |
| /* Select PIO or DMA, DMA may only be selected for one drive/channel. */ |
| bit = 1 << (20 + drive->select.b.unit + (hwif->channel << 1)); |
| other = 1 << (20 + (1 - drive->select.b.unit) + (hwif->channel << 1)); |
| new = use_dma ? ((new & ~other) | bit) : (new & ~bit); |
| |
| if (new != *old) { |
| unsigned char stat; |
| |
| /* |
| * Don't change DMA engine settings while Write Buffers |
| * are busy. |
| */ |
| (void) pci_read_config_byte(dev, 0x43, &stat); |
| while (stat & 0x03) { |
| udelay(1); |
| (void) pci_read_config_byte(dev, 0x43, &stat); |
| } |
| |
| *old = new; |
| (void) pci_write_config_dword(dev, 0x40, new); |
| |
| /* |
| * And let things settle... |
| */ |
| udelay(10); |
| } |
| |
| local_irq_restore(flags); |
| } |
| |
| static void ns87415_selectproc (ide_drive_t *drive) |
| { |
| ns87415_prepare_drive (drive, drive->using_dma); |
| } |
| |
| static int ns87415_ide_dma_end (ide_drive_t *drive) |
| { |
| ide_hwif_t *hwif = HWIF(drive); |
| u8 dma_stat = 0, dma_cmd = 0; |
| |
| drive->waiting_for_dma = 0; |
| dma_stat = hwif->INB(hwif->dma_status); |
| /* get dma command mode */ |
| dma_cmd = hwif->INB(hwif->dma_command); |
| /* stop DMA */ |
| outb(dma_cmd & ~1, hwif->dma_command); |
| /* from ERRATA: clear the INTR & ERROR bits */ |
| dma_cmd = hwif->INB(hwif->dma_command); |
| outb(dma_cmd | 6, hwif->dma_command); |
| /* and free any DMA resources */ |
| ide_destroy_dmatable(drive); |
| /* verify good DMA status */ |
| return (dma_stat & 7) != 4; |
| } |
| |
| static int ns87415_ide_dma_setup(ide_drive_t *drive) |
| { |
| /* select DMA xfer */ |
| ns87415_prepare_drive(drive, 1); |
| if (!ide_dma_setup(drive)) |
| return 0; |
| /* DMA failed: select PIO xfer */ |
| ns87415_prepare_drive(drive, 0); |
| return 1; |
| } |
| |
| static int ns87415_ide_dma_check (ide_drive_t *drive) |
| { |
| if (drive->media != ide_disk) |
| return -1; |
| |
| return __ide_dma_check(drive); |
| } |
| |
| static void __devinit init_hwif_ns87415 (ide_hwif_t *hwif) |
| { |
| struct pci_dev *dev = hwif->pci_dev; |
| unsigned int ctrl, using_inta; |
| u8 progif; |
| #ifdef __sparc_v9__ |
| int timeout; |
| u8 stat; |
| #endif |
| |
| hwif->autodma = 0; |
| hwif->selectproc = &ns87415_selectproc; |
| |
| /* |
| * We cannot probe for IRQ: both ports share common IRQ on INTA. |
| * Also, leave IRQ masked during drive probing, to prevent infinite |
| * interrupts from a potentially floating INTA.. |
| * |
| * IRQs get unmasked in selectproc when drive is first used. |
| */ |
| (void) pci_read_config_dword(dev, 0x40, &ctrl); |
| (void) pci_read_config_byte(dev, 0x09, &progif); |
| /* is irq in "native" mode? */ |
| using_inta = progif & (1 << (hwif->channel << 1)); |
| if (!using_inta) |
| using_inta = ctrl & (1 << (4 + hwif->channel)); |
| if (hwif->mate) { |
| hwif->select_data = hwif->mate->select_data; |
| } else { |
| hwif->select_data = (unsigned long) |
| &ns87415_control[ns87415_count++]; |
| ctrl |= (1 << 8) | (1 << 9); /* mask both IRQs */ |
| if (using_inta) |
| ctrl &= ~(1 << 6); /* unmask INTA */ |
| *((unsigned int *)hwif->select_data) = ctrl; |
| (void) pci_write_config_dword(dev, 0x40, ctrl); |
| |
| /* |
| * Set prefetch size to 512 bytes for both ports, |
| * but don't turn on/off prefetching here. |
| */ |
| pci_write_config_byte(dev, 0x55, 0xee); |
| |
| #ifdef __sparc_v9__ |
| /* |
| * XXX: Reset the device, if we don't it will not respond |
| * to SELECT_DRIVE() properly during first probe_hwif(). |
| */ |
| timeout = 10000; |
| outb(12, hwif->io_ports[IDE_CONTROL_OFFSET]); |
| udelay(10); |
| outb(8, hwif->io_ports[IDE_CONTROL_OFFSET]); |
| do { |
| udelay(50); |
| stat = hwif->INB(hwif->io_ports[IDE_STATUS_OFFSET]); |
| if (stat == 0xff) |
| break; |
| } while ((stat & BUSY_STAT) && --timeout); |
| #endif |
| } |
| |
| if (!using_inta) |
| hwif->irq = ide_default_irq(hwif->io_ports[IDE_DATA_OFFSET]); |
| else if (!hwif->irq && hwif->mate && hwif->mate->irq) |
| hwif->irq = hwif->mate->irq; /* share IRQ with mate */ |
| |
| if (!hwif->dma_base) |
| return; |
| |
| outb(0x60, hwif->dma_status); |
| hwif->dma_setup = &ns87415_ide_dma_setup; |
| hwif->ide_dma_check = &ns87415_ide_dma_check; |
| hwif->ide_dma_end = &ns87415_ide_dma_end; |
| |
| if (!noautodma) |
| hwif->autodma = 1; |
| hwif->drives[0].autodma = hwif->autodma; |
| hwif->drives[1].autodma = hwif->autodma; |
| } |
| |
| static ide_pci_device_t ns87415_chipset __devinitdata = { |
| .name = "NS87415", |
| #ifdef CONFIG_SUPERIO |
| .init_iops = init_iops_ns87415, |
| #endif |
| .init_hwif = init_hwif_ns87415, |
| .channels = 2, |
| .autodma = AUTODMA, |
| .bootable = ON_BOARD, |
| }; |
| |
| static int __devinit ns87415_init_one(struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| return ide_setup_pci_device(dev, &ns87415_chipset); |
| } |
| |
| static struct pci_device_id ns87415_pci_tbl[] = { |
| { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, |
| { 0, }, |
| }; |
| MODULE_DEVICE_TABLE(pci, ns87415_pci_tbl); |
| |
| static struct pci_driver driver = { |
| .name = "NS87415_IDE", |
| .id_table = ns87415_pci_tbl, |
| .probe = ns87415_init_one, |
| }; |
| |
| static int __init ns87415_ide_init(void) |
| { |
| return ide_pci_register_driver(&driver); |
| } |
| |
| module_init(ns87415_ide_init); |
| |
| MODULE_AUTHOR("Mark Lord, Eddie Dost, Andre Hedrick"); |
| MODULE_DESCRIPTION("PCI driver module for NS87415 IDE"); |
| MODULE_LICENSE("GPL"); |