blob: 3b8d6d19ff0595885570713d7f866c732695a0db [file] [log] [blame]
/****************************************************************************/
/*
* fec.h -- Fast Ethernet Controller for Motorola ColdFire SoC
* processors.
*
* (C) Copyright 2000-2005, Greg Ungerer (gerg@snapgear.com)
* (C) Copyright 2000-2001, Lineo (www.lineo.com)
*/
/****************************************************************************/
#ifndef FEC_H
#define FEC_H
/****************************************************************************/
#include <linux/clocksource.h>
#include <linux/net_tstamp.h>
#include <linux/ptp_clock_kernel.h>
#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
defined(CONFIG_M520x) || defined(CONFIG_M532x) || \
defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
/*
* Just figures, Motorola would have to change the offsets for
* registers in the same peripheral device on different models
* of the ColdFire!
*/
#define FEC_IEVENT 0x004 /* Interrupt event reg */
#define FEC_IMASK 0x008 /* Interrupt mask reg */
#define FEC_R_DES_ACTIVE 0x010 /* Receive descriptor reg */
#define FEC_X_DES_ACTIVE 0x014 /* Transmit descriptor reg */
#define FEC_ECNTRL 0x024 /* Ethernet control reg */
#define FEC_MII_DATA 0x040 /* MII manage frame reg */
#define FEC_MII_SPEED 0x044 /* MII speed control reg */
#define FEC_MIB_CTRLSTAT 0x064 /* MIB control/status reg */
#define FEC_R_CNTRL 0x084 /* Receive control reg */
#define FEC_X_CNTRL 0x0c4 /* Transmit Control reg */
#define FEC_ADDR_LOW 0x0e4 /* Low 32bits MAC address */
#define FEC_ADDR_HIGH 0x0e8 /* High 16bits MAC address */
#define FEC_OPD 0x0ec /* Opcode + Pause duration */
#define FEC_HASH_TABLE_HIGH 0x118 /* High 32bits hash table */
#define FEC_HASH_TABLE_LOW 0x11c /* Low 32bits hash table */
#define FEC_GRP_HASH_TABLE_HIGH 0x120 /* High 32bits hash table */
#define FEC_GRP_HASH_TABLE_LOW 0x124 /* Low 32bits hash table */
#define FEC_X_WMRK 0x144 /* FIFO transmit water mark */
#define FEC_R_BOUND 0x14c /* FIFO receive bound reg */
#define FEC_R_FSTART 0x150 /* FIFO receive start reg */
#define FEC_R_DES_START 0x180 /* Receive descriptor ring */
#define FEC_X_DES_START 0x184 /* Transmit descriptor ring */
#define FEC_R_BUFF_SIZE 0x188 /* Maximum receive buff size */
#define FEC_R_FIFO_RSFL 0x190 /* Receive FIFO section full threshold */
#define FEC_R_FIFO_RSEM 0x194 /* Receive FIFO section empty threshold */
#define FEC_R_FIFO_RAEM 0x198 /* Receive FIFO almost empty threshold */
#define FEC_R_FIFO_RAFL 0x19c /* Receive FIFO almost full threshold */
#define FEC_RACC 0x1C4 /* Receive Accelerator function */
#define FEC_MIIGSK_CFGR 0x300 /* MIIGSK Configuration reg */
#define FEC_MIIGSK_ENR 0x308 /* MIIGSK Enable reg */
#define BM_MIIGSK_CFGR_MII 0x00
#define BM_MIIGSK_CFGR_RMII 0x01
#define BM_MIIGSK_CFGR_FRCONT_10M 0x40
#define RMON_T_DROP 0x200 /* Count of frames not cntd correctly */
#define RMON_T_PACKETS 0x204 /* RMON TX packet count */
#define RMON_T_BC_PKT 0x208 /* RMON TX broadcast pkts */
#define RMON_T_MC_PKT 0x20C /* RMON TX multicast pkts */
#define RMON_T_CRC_ALIGN 0x210 /* RMON TX pkts with CRC align err */
#define RMON_T_UNDERSIZE 0x214 /* RMON TX pkts < 64 bytes, good CRC */
#define RMON_T_OVERSIZE 0x218 /* RMON TX pkts > MAX_FL bytes good CRC */
#define RMON_T_FRAG 0x21C /* RMON TX pkts < 64 bytes, bad CRC */
#define RMON_T_JAB 0x220 /* RMON TX pkts > MAX_FL bytes, bad CRC */
#define RMON_T_COL 0x224 /* RMON TX collision count */
#define RMON_T_P64 0x228 /* RMON TX 64 byte pkts */
#define RMON_T_P65TO127 0x22C /* RMON TX 65 to 127 byte pkts */
#define RMON_T_P128TO255 0x230 /* RMON TX 128 to 255 byte pkts */
#define RMON_T_P256TO511 0x234 /* RMON TX 256 to 511 byte pkts */
#define RMON_T_P512TO1023 0x238 /* RMON TX 512 to 1023 byte pkts */
#define RMON_T_P1024TO2047 0x23C /* RMON TX 1024 to 2047 byte pkts */
#define RMON_T_P_GTE2048 0x240 /* RMON TX pkts > 2048 bytes */
#define RMON_T_OCTETS 0x244 /* RMON TX octets */
#define IEEE_T_DROP 0x248 /* Count of frames not counted crtly */
#define IEEE_T_FRAME_OK 0x24C /* Frames tx'd OK */
#define IEEE_T_1COL 0x250 /* Frames tx'd with single collision */
#define IEEE_T_MCOL 0x254 /* Frames tx'd with multiple collision */
#define IEEE_T_DEF 0x258 /* Frames tx'd after deferral delay */
#define IEEE_T_LCOL 0x25C /* Frames tx'd with late collision */
#define IEEE_T_EXCOL 0x260 /* Frames tx'd with excesv collisions */
#define IEEE_T_MACERR 0x264 /* Frames tx'd with TX FIFO underrun */
#define IEEE_T_CSERR 0x268 /* Frames tx'd with carrier sense err */
#define IEEE_T_SQE 0x26C /* Frames tx'd with SQE err */
#define IEEE_T_FDXFC 0x270 /* Flow control pause frames tx'd */
#define IEEE_T_OCTETS_OK 0x274 /* Octet count for frames tx'd w/o err */
#define RMON_R_PACKETS 0x284 /* RMON RX packet count */
#define RMON_R_BC_PKT 0x288 /* RMON RX broadcast pkts */
#define RMON_R_MC_PKT 0x28C /* RMON RX multicast pkts */
#define RMON_R_CRC_ALIGN 0x290 /* RMON RX pkts with CRC alignment err */
#define RMON_R_UNDERSIZE 0x294 /* RMON RX pkts < 64 bytes, good CRC */
#define RMON_R_OVERSIZE 0x298 /* RMON RX pkts > MAX_FL bytes good CRC */
#define RMON_R_FRAG 0x29C /* RMON RX pkts < 64 bytes, bad CRC */
#define RMON_R_JAB 0x2A0 /* RMON RX pkts > MAX_FL bytes, bad CRC */
#define RMON_R_RESVD_O 0x2A4 /* Reserved */
#define RMON_R_P64 0x2A8 /* RMON RX 64 byte pkts */
#define RMON_R_P65TO127 0x2AC /* RMON RX 65 to 127 byte pkts */
#define RMON_R_P128TO255 0x2B0 /* RMON RX 128 to 255 byte pkts */
#define RMON_R_P256TO511 0x2B4 /* RMON RX 256 to 511 byte pkts */
#define RMON_R_P512TO1023 0x2B8 /* RMON RX 512 to 1023 byte pkts */
#define RMON_R_P1024TO2047 0x2BC /* RMON RX 1024 to 2047 byte pkts */
#define RMON_R_P_GTE2048 0x2C0 /* RMON RX pkts > 2048 bytes */
#define RMON_R_OCTETS 0x2C4 /* RMON RX octets */
#define IEEE_R_DROP 0x2C8 /* Count frames not counted correctly */
#define IEEE_R_FRAME_OK 0x2CC /* Frames rx'd OK */
#define IEEE_R_CRC 0x2D0 /* Frames rx'd with CRC err */
#define IEEE_R_ALIGN 0x2D4 /* Frames rx'd with alignment err */
#define IEEE_R_MACERR 0x2D8 /* Receive FIFO overflow count */
#define IEEE_R_FDXFC 0x2DC /* Flow control pause frames rx'd */
#define IEEE_R_OCTETS_OK 0x2E0 /* Octet cnt for frames rx'd w/o err */
#else
#define FEC_ECNTRL 0x000 /* Ethernet control reg */
#define FEC_IEVENT 0x004 /* Interrupt even reg */
#define FEC_IMASK 0x008 /* Interrupt mask reg */
#define FEC_IVEC 0x00c /* Interrupt vec status reg */
#define FEC_R_DES_ACTIVE 0x010 /* Receive descriptor reg */
#define FEC_X_DES_ACTIVE 0x014 /* Transmit descriptor reg */
#define FEC_MII_DATA 0x040 /* MII manage frame reg */
#define FEC_MII_SPEED 0x044 /* MII speed control reg */
#define FEC_R_BOUND 0x08c /* FIFO receive bound reg */
#define FEC_R_FSTART 0x090 /* FIFO receive start reg */
#define FEC_X_WMRK 0x0a4 /* FIFO transmit water mark */
#define FEC_X_FSTART 0x0ac /* FIFO transmit start reg */
#define FEC_R_CNTRL 0x104 /* Receive control reg */
#define FEC_MAX_FRM_LEN 0x108 /* Maximum frame length reg */
#define FEC_X_CNTRL 0x144 /* Transmit Control reg */
#define FEC_ADDR_LOW 0x3c0 /* Low 32bits MAC address */
#define FEC_ADDR_HIGH 0x3c4 /* High 16bits MAC address */
#define FEC_GRP_HASH_TABLE_HIGH 0x3c8 /* High 32bits hash table */
#define FEC_GRP_HASH_TABLE_LOW 0x3cc /* Low 32bits hash table */
#define FEC_R_DES_START 0x3d0 /* Receive descriptor ring */
#define FEC_X_DES_START 0x3d4 /* Transmit descriptor ring */
#define FEC_R_BUFF_SIZE 0x3d8 /* Maximum receive buff size */
#define FEC_FIFO_RAM 0x400 /* FIFO RAM buffer */
#endif /* CONFIG_M5272 */
/*
* Define the buffer descriptor structure.
*/
#if defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
struct bufdesc {
unsigned short cbd_datlen; /* Data length */
unsigned short cbd_sc; /* Control and status info */
unsigned long cbd_bufaddr; /* Buffer address */
};
#else
struct bufdesc {
unsigned short cbd_sc; /* Control and status info */
unsigned short cbd_datlen; /* Data length */
unsigned long cbd_bufaddr; /* Buffer address */
};
#endif
struct bufdesc_ex {
struct bufdesc desc;
unsigned long cbd_esc;
unsigned long cbd_prot;
unsigned long cbd_bdu;
unsigned long ts;
unsigned short res0[4];
};
/*
* The following definitions courtesy of commproc.h, which where
* Copyright (c) 1997 Dan Malek (dmalek@jlc.net).
*/
#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
#define BD_SC_CM ((ushort)0x0200) /* Continuous mode */
#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
#define BD_SC_BR ((ushort)0x0020) /* Break received */
#define BD_SC_FR ((ushort)0x0010) /* Framing error */
#define BD_SC_PR ((ushort)0x0008) /* Parity error */
#define BD_SC_OV ((ushort)0x0002) /* Overrun */
#define BD_SC_CD ((ushort)0x0001) /* ?? */
/* Buffer descriptor control/status used by Ethernet receive.
*/
#define BD_ENET_RX_EMPTY ((ushort)0x8000)
#define BD_ENET_RX_WRAP ((ushort)0x2000)
#define BD_ENET_RX_INTR ((ushort)0x1000)
#define BD_ENET_RX_LAST ((ushort)0x0800)
#define BD_ENET_RX_FIRST ((ushort)0x0400)
#define BD_ENET_RX_MISS ((ushort)0x0100)
#define BD_ENET_RX_LG ((ushort)0x0020)
#define BD_ENET_RX_NO ((ushort)0x0010)
#define BD_ENET_RX_SH ((ushort)0x0008)
#define BD_ENET_RX_CR ((ushort)0x0004)
#define BD_ENET_RX_OV ((ushort)0x0002)
#define BD_ENET_RX_CL ((ushort)0x0001)
#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
/* Enhanced buffer descriptor control/status used by Ethernet receive */
#define BD_ENET_RX_VLAN 0x00000004
/* Buffer descriptor control/status used by Ethernet transmit.
*/
#define BD_ENET_TX_READY ((ushort)0x8000)
#define BD_ENET_TX_PAD ((ushort)0x4000)
#define BD_ENET_TX_WRAP ((ushort)0x2000)
#define BD_ENET_TX_INTR ((ushort)0x1000)
#define BD_ENET_TX_LAST ((ushort)0x0800)
#define BD_ENET_TX_TC ((ushort)0x0400)
#define BD_ENET_TX_DEF ((ushort)0x0200)
#define BD_ENET_TX_HB ((ushort)0x0100)
#define BD_ENET_TX_LC ((ushort)0x0080)
#define BD_ENET_TX_RL ((ushort)0x0040)
#define BD_ENET_TX_RCMASK ((ushort)0x003c)
#define BD_ENET_TX_UN ((ushort)0x0002)
#define BD_ENET_TX_CSL ((ushort)0x0001)
#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
/*enhanced buffer descriptor control/status used by Ethernet transmit*/
#define BD_ENET_TX_INT 0x40000000
#define BD_ENET_TX_TS 0x20000000
#define BD_ENET_TX_PINS 0x10000000
#define BD_ENET_TX_IINS 0x08000000
/* This device has up to three irqs on some platforms */
#define FEC_IRQ_NUM 3
/* The number of Tx and Rx buffers. These are allocated from the page
* pool. The code may assume these are power of two, so it it best
* to keep them that size.
* We don't need to allocate pages for the transmitter. We just use
* the skbuffer directly.
*/
#define FEC_ENET_RX_PAGES 8
#define FEC_ENET_RX_FRSIZE 2048
#define FEC_ENET_RX_FRPPG (PAGE_SIZE / FEC_ENET_RX_FRSIZE)
#define RX_RING_SIZE (FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
#define FEC_ENET_TX_FRSIZE 2048
#define FEC_ENET_TX_FRPPG (PAGE_SIZE / FEC_ENET_TX_FRSIZE)
#define TX_RING_SIZE 16 /* Must be power of two */
#define TX_RING_MOD_MASK 15 /* for this to work */
#define BD_ENET_RX_INT 0x00800000
#define BD_ENET_RX_PTP ((ushort)0x0400)
#define BD_ENET_RX_ICE 0x00000020
#define BD_ENET_RX_PCR 0x00000010
#define FLAG_RX_CSUM_ENABLED (BD_ENET_RX_ICE | BD_ENET_RX_PCR)
#define FLAG_RX_CSUM_ERROR (BD_ENET_RX_ICE | BD_ENET_RX_PCR)
struct fec_enet_delayed_work {
struct delayed_work delay_work;
bool timeout;
bool trig_tx;
};
/* The FEC buffer descriptors track the ring buffers. The rx_bd_base and
* tx_bd_base always point to the base of the buffer descriptors. The
* cur_rx and cur_tx point to the currently available buffer.
* The dirty_tx tracks the current buffer that is being sent by the
* controller. The cur_tx and dirty_tx are equal under both completely
* empty and completely full conditions. The empty/ready indicator in
* the buffer descriptor determines the actual condition.
*/
struct fec_enet_private {
/* Hardware registers of the FEC device */
void __iomem *hwp;
struct net_device *netdev;
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_enet_out;
struct clk *clk_ptp;
/* The saved address of a sent-in-place packet/buffer, for skfree(). */
unsigned char *tx_bounce[TX_RING_SIZE];
struct sk_buff *tx_skbuff[TX_RING_SIZE];
struct sk_buff *rx_skbuff[RX_RING_SIZE];
/* CPM dual port RAM relative addresses */
dma_addr_t bd_dma;
/* Address of Rx and Tx buffers */
struct bufdesc *rx_bd_base;
struct bufdesc *tx_bd_base;
/* The next free ring entry */
struct bufdesc *cur_rx, *cur_tx;
/* The ring entries to be free()ed */
struct bufdesc *dirty_tx;
unsigned short tx_ring_size;
unsigned short rx_ring_size;
struct platform_device *pdev;
int opened;
int dev_id;
/* Phylib and MDIO interface */
struct mii_bus *mii_bus;
struct phy_device *phy_dev;
int mii_timeout;
uint phy_speed;
phy_interface_t phy_interface;
int link;
int full_duplex;
int speed;
struct completion mdio_done;
int irq[FEC_IRQ_NUM];
int bufdesc_ex;
int pause_flag;
struct napi_struct napi;
int csum_flags;
struct ptp_clock *ptp_clock;
struct ptp_clock_info ptp_caps;
unsigned long last_overflow_check;
spinlock_t tmreg_lock;
struct cyclecounter cc;
struct timecounter tc;
int rx_hwtstamp_filter;
u32 base_incval;
u32 cycle_speed;
int hwts_rx_en;
int hwts_tx_en;
struct timer_list time_keep;
struct fec_enet_delayed_work delay_work;
struct regulator *reg_phy;
};
void fec_ptp_init(struct platform_device *pdev);
void fec_ptp_start_cyclecounter(struct net_device *ndev);
int fec_ptp_set(struct net_device *ndev, struct ifreq *ifr);
int fec_ptp_get(struct net_device *ndev, struct ifreq *ifr);
/****************************************************************************/
#endif /* FEC_H */