| /* |
| * kota2 board support |
| * |
| * Copyright (C) 2011 Renesas Solutions Corp. |
| * Copyright (C) 2011 Magnus Damm |
| * Copyright (C) 2010 Takashi Yoshii <yoshii.takashi.zj@renesas.com> |
| * Copyright (C) 2009 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/delay.h> |
| #include <linux/io.h> |
| #include <linux/smsc911x.h> |
| #include <linux/gpio.h> |
| #include <linux/input.h> |
| #include <linux/input/sh_keysc.h> |
| #include <linux/gpio_keys.h> |
| #include <linux/leds.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/sh_mmcif.h> |
| #include <linux/mfd/tmio.h> |
| #include <linux/mmc/sh_mobile_sdhi.h> |
| #include <mach/hardware.h> |
| #include <mach/sh73a0.h> |
| #include <mach/common.h> |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/time.h> |
| #include <asm/hardware/gic.h> |
| #include <asm/hardware/cache-l2x0.h> |
| #include <asm/traps.h> |
| |
| /* SMSC 9220 */ |
| static struct resource smsc9220_resources[] = { |
| [0] = { |
| .start = 0x14000000, /* CS5A */ |
| .end = 0x140000ff, /* A1->A7 */ |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gic_spi(33), /* PINTA2 @ PORT144 */ |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct smsc911x_platform_config smsc9220_platdata = { |
| .flags = SMSC911X_USE_32BIT, /* 32-bit SW on 16-bit HW bus */ |
| .phy_interface = PHY_INTERFACE_MODE_MII, |
| .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, |
| }; |
| |
| static struct platform_device eth_device = { |
| .name = "smsc911x", |
| .id = 0, |
| .dev = { |
| .platform_data = &smsc9220_platdata, |
| }, |
| .resource = smsc9220_resources, |
| .num_resources = ARRAY_SIZE(smsc9220_resources), |
| }; |
| |
| /* KEYSC */ |
| static struct sh_keysc_info keysc_platdata = { |
| .mode = SH_KEYSC_MODE_6, |
| .scan_timing = 3, |
| .delay = 100, |
| .keycodes = { |
| KEY_NUMERIC_STAR, KEY_NUMERIC_0, KEY_NUMERIC_POUND, |
| 0, 0, 0, 0, 0, |
| KEY_NUMERIC_7, KEY_NUMERIC_8, KEY_NUMERIC_9, |
| 0, KEY_DOWN, 0, 0, 0, |
| KEY_NUMERIC_4, KEY_NUMERIC_5, KEY_NUMERIC_6, |
| KEY_LEFT, KEY_ENTER, KEY_RIGHT, 0, 0, |
| KEY_NUMERIC_1, KEY_NUMERIC_2, KEY_NUMERIC_3, |
| 0, KEY_UP, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, |
| }, |
| }; |
| |
| static struct resource keysc_resources[] = { |
| [0] = { |
| .name = "KEYSC", |
| .start = 0xe61b0000, |
| .end = 0xe61b0098 - 1, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gic_spi(71), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device keysc_device = { |
| .name = "sh_keysc", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(keysc_resources), |
| .resource = keysc_resources, |
| .dev = { |
| .platform_data = &keysc_platdata, |
| }, |
| }; |
| |
| /* GPIO KEY */ |
| #define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 } |
| |
| static struct gpio_keys_button gpio_buttons[] = { |
| GPIO_KEY(KEY_VOLUMEUP, GPIO_PORT56, "+"), /* S2: VOL+ [IRQ9] */ |
| GPIO_KEY(KEY_VOLUMEDOWN, GPIO_PORT54, "-"), /* S3: VOL- [IRQ10] */ |
| GPIO_KEY(KEY_MENU, GPIO_PORT27, "Menu"), /* S4: MENU [IRQ30] */ |
| GPIO_KEY(KEY_HOMEPAGE, GPIO_PORT26, "Home"), /* S5: HOME [IRQ31] */ |
| GPIO_KEY(KEY_BACK, GPIO_PORT11, "Back"), /* S6: BACK [IRQ0] */ |
| GPIO_KEY(KEY_PHONE, GPIO_PORT238, "Tel"), /* S7: TEL [IRQ11] */ |
| GPIO_KEY(KEY_POWER, GPIO_PORT239, "C1"), /* S8: CAM [IRQ13] */ |
| GPIO_KEY(KEY_MAIL, GPIO_PORT224, "Mail"), /* S9: MAIL [IRQ3] */ |
| /* Omitted button "C3?": GPIO_PORT223 - S10: CUST [IRQ8] */ |
| GPIO_KEY(KEY_CAMERA, GPIO_PORT164, "C2"), /* S11: CAM_HALF [IRQ25] */ |
| /* Omitted button "?": GPIO_PORT152 - S12: CAM_FULL [No IRQ] */ |
| }; |
| |
| static struct gpio_keys_platform_data gpio_key_info = { |
| .buttons = gpio_buttons, |
| .nbuttons = ARRAY_SIZE(gpio_buttons), |
| .poll_interval = 250, /* polled for now */ |
| }; |
| |
| static struct platform_device gpio_keys_device = { |
| .name = "gpio-keys-polled", /* polled for now */ |
| .id = -1, |
| .dev = { |
| .platform_data = &gpio_key_info, |
| }, |
| }; |
| |
| /* GPIO LED */ |
| #define GPIO_LED(n, g) { .name = n, .gpio = g } |
| |
| static struct gpio_led gpio_leds[] = { |
| GPIO_LED("V2513", GPIO_PORT153), /* PORT153 [TPU1T02] -> V2513 */ |
| GPIO_LED("V2514", GPIO_PORT199), /* PORT199 [TPU4TO1] -> V2514 */ |
| GPIO_LED("V2515", GPIO_PORT197), /* PORT197 [TPU2TO1] -> V2515 */ |
| GPIO_LED("KEYLED", GPIO_PORT163), /* PORT163 [TPU3TO0] -> KEYLED */ |
| GPIO_LED("G", GPIO_PORT20), /* PORT20 [GPO0] -> LED7 -> "G" */ |
| GPIO_LED("H", GPIO_PORT21), /* PORT21 [GPO1] -> LED8 -> "H" */ |
| GPIO_LED("J", GPIO_PORT22), /* PORT22 [GPO2] -> LED9 -> "J" */ |
| }; |
| |
| static struct gpio_led_platform_data gpio_leds_info = { |
| .leds = gpio_leds, |
| .num_leds = ARRAY_SIZE(gpio_leds), |
| }; |
| |
| static struct platform_device gpio_leds_device = { |
| .name = "leds-gpio", |
| .id = -1, |
| .dev = { |
| .platform_data = &gpio_leds_info, |
| }, |
| }; |
| |
| /* MMCIF */ |
| static struct resource mmcif_resources[] = { |
| [0] = { |
| .name = "MMCIF", |
| .start = 0xe6bd0000, |
| .end = 0xe6bd00ff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gic_spi(140), |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = gic_spi(141), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct sh_mmcif_plat_data mmcif_info = { |
| .ocr = MMC_VDD_165_195, |
| .caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE, |
| }; |
| |
| static struct platform_device mmcif_device = { |
| .name = "sh_mmcif", |
| .id = 0, |
| .dev = { |
| .platform_data = &mmcif_info, |
| }, |
| .num_resources = ARRAY_SIZE(mmcif_resources), |
| .resource = mmcif_resources, |
| }; |
| |
| /* SDHI0 */ |
| static struct sh_mobile_sdhi_info sdhi0_info = { |
| .tmio_caps = MMC_CAP_SD_HIGHSPEED, |
| .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT, |
| }; |
| |
| static struct resource sdhi0_resources[] = { |
| [0] = { |
| .name = "SDHI0", |
| .start = 0xee100000, |
| .end = 0xee1000ff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gic_spi(83), |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = gic_spi(84), |
| .flags = IORESOURCE_IRQ, |
| }, |
| [3] = { |
| .start = gic_spi(85), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device sdhi0_device = { |
| .name = "sh_mobile_sdhi", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(sdhi0_resources), |
| .resource = sdhi0_resources, |
| .dev = { |
| .platform_data = &sdhi0_info, |
| }, |
| }; |
| |
| /* SDHI1 */ |
| static struct sh_mobile_sdhi_info sdhi1_info = { |
| .tmio_caps = MMC_CAP_NONREMOVABLE | MMC_CAP_SDIO_IRQ, |
| .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT, |
| }; |
| |
| static struct resource sdhi1_resources[] = { |
| [0] = { |
| .name = "SDHI1", |
| .start = 0xee120000, |
| .end = 0xee1200ff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = gic_spi(87), |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = gic_spi(88), |
| .flags = IORESOURCE_IRQ, |
| }, |
| [3] = { |
| .start = gic_spi(89), |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device sdhi1_device = { |
| .name = "sh_mobile_sdhi", |
| .id = 1, |
| .num_resources = ARRAY_SIZE(sdhi1_resources), |
| .resource = sdhi1_resources, |
| .dev = { |
| .platform_data = &sdhi1_info, |
| }, |
| }; |
| |
| static struct platform_device *kota2_devices[] __initdata = { |
| ð_device, |
| &keysc_device, |
| &gpio_keys_device, |
| &gpio_leds_device, |
| &mmcif_device, |
| &sdhi0_device, |
| &sdhi1_device, |
| }; |
| |
| static struct map_desc kota2_io_desc[] __initdata = { |
| /* create a 1:1 entity map for 0xe6xxxxxx |
| * used by CPGA, INTC and PFC. |
| */ |
| { |
| .virtual = 0xe6000000, |
| .pfn = __phys_to_pfn(0xe6000000), |
| .length = 256 << 20, |
| .type = MT_DEVICE_NONSHARED |
| }, |
| }; |
| |
| static void __init kota2_map_io(void) |
| { |
| iotable_init(kota2_io_desc, ARRAY_SIZE(kota2_io_desc)); |
| |
| /* setup early devices and console here as well */ |
| sh73a0_add_early_devices(); |
| shmobile_setup_console(); |
| } |
| |
| #define PINTER0A 0xe69000a0 |
| #define PINTCR0A 0xe69000b0 |
| |
| void __init kota2_init_irq(void) |
| { |
| sh73a0_init_irq(); |
| |
| /* setup PINT: enable PINTA2 as active low */ |
| __raw_writel(1 << 29, PINTER0A); |
| __raw_writew(2 << 10, PINTCR0A); |
| } |
| |
| static void __init kota2_init(void) |
| { |
| sh73a0_pinmux_init(); |
| |
| /* SCIFA2 (UART2) */ |
| gpio_request(GPIO_FN_SCIFA2_TXD1, NULL); |
| gpio_request(GPIO_FN_SCIFA2_RXD1, NULL); |
| gpio_request(GPIO_FN_SCIFA2_RTS1_, NULL); |
| gpio_request(GPIO_FN_SCIFA2_CTS1_, NULL); |
| |
| /* SCIFA4 (UART1) */ |
| gpio_request(GPIO_FN_SCIFA4_TXD, NULL); |
| gpio_request(GPIO_FN_SCIFA4_RXD, NULL); |
| gpio_request(GPIO_FN_SCIFA4_RTS_, NULL); |
| gpio_request(GPIO_FN_SCIFA4_CTS_, NULL); |
| |
| /* SMSC911X */ |
| gpio_request(GPIO_FN_D0_NAF0, NULL); |
| gpio_request(GPIO_FN_D1_NAF1, NULL); |
| gpio_request(GPIO_FN_D2_NAF2, NULL); |
| gpio_request(GPIO_FN_D3_NAF3, NULL); |
| gpio_request(GPIO_FN_D4_NAF4, NULL); |
| gpio_request(GPIO_FN_D5_NAF5, NULL); |
| gpio_request(GPIO_FN_D6_NAF6, NULL); |
| gpio_request(GPIO_FN_D7_NAF7, NULL); |
| gpio_request(GPIO_FN_D8_NAF8, NULL); |
| gpio_request(GPIO_FN_D9_NAF9, NULL); |
| gpio_request(GPIO_FN_D10_NAF10, NULL); |
| gpio_request(GPIO_FN_D11_NAF11, NULL); |
| gpio_request(GPIO_FN_D12_NAF12, NULL); |
| gpio_request(GPIO_FN_D13_NAF13, NULL); |
| gpio_request(GPIO_FN_D14_NAF14, NULL); |
| gpio_request(GPIO_FN_D15_NAF15, NULL); |
| gpio_request(GPIO_FN_CS5A_, NULL); |
| gpio_request(GPIO_FN_WE0__FWE, NULL); |
| gpio_request(GPIO_PORT144, NULL); /* PINTA2 */ |
| gpio_direction_input(GPIO_PORT144); |
| gpio_request(GPIO_PORT145, NULL); /* RESET */ |
| gpio_direction_output(GPIO_PORT145, 1); |
| |
| /* KEYSC */ |
| gpio_request(GPIO_FN_KEYIN0_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN1_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN2_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN3_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN4_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN5_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN6_PU, NULL); |
| gpio_request(GPIO_FN_KEYIN7_PU, NULL); |
| gpio_request(GPIO_FN_KEYOUT0, NULL); |
| gpio_request(GPIO_FN_KEYOUT1, NULL); |
| gpio_request(GPIO_FN_KEYOUT2, NULL); |
| gpio_request(GPIO_FN_KEYOUT3, NULL); |
| gpio_request(GPIO_FN_KEYOUT4, NULL); |
| gpio_request(GPIO_FN_KEYOUT5, NULL); |
| gpio_request(GPIO_FN_PORT59_KEYOUT6, NULL); |
| gpio_request(GPIO_FN_PORT58_KEYOUT7, NULL); |
| gpio_request(GPIO_FN_KEYOUT8, NULL); |
| |
| /* MMCIF */ |
| gpio_request(GPIO_FN_MMCCLK0, NULL); |
| gpio_request(GPIO_FN_MMCD0_0, NULL); |
| gpio_request(GPIO_FN_MMCD0_1, NULL); |
| gpio_request(GPIO_FN_MMCD0_2, NULL); |
| gpio_request(GPIO_FN_MMCD0_3, NULL); |
| gpio_request(GPIO_FN_MMCD0_4, NULL); |
| gpio_request(GPIO_FN_MMCD0_5, NULL); |
| gpio_request(GPIO_FN_MMCD0_6, NULL); |
| gpio_request(GPIO_FN_MMCD0_7, NULL); |
| gpio_request(GPIO_FN_MMCCMD0, NULL); |
| gpio_request(GPIO_PORT208, NULL); /* Reset */ |
| gpio_direction_output(GPIO_PORT208, 1); |
| |
| /* SDHI0 (microSD) */ |
| gpio_request(GPIO_FN_SDHICD0_PU, NULL); |
| gpio_request(GPIO_FN_SDHICMD0_PU, NULL); |
| gpio_request(GPIO_FN_SDHICLK0, NULL); |
| gpio_request(GPIO_FN_SDHID0_3_PU, NULL); |
| gpio_request(GPIO_FN_SDHID0_2_PU, NULL); |
| gpio_request(GPIO_FN_SDHID0_1_PU, NULL); |
| gpio_request(GPIO_FN_SDHID0_0_PU, NULL); |
| |
| /* SCIFB (BT) */ |
| gpio_request(GPIO_FN_PORT159_SCIFB_SCK, NULL); |
| gpio_request(GPIO_FN_PORT160_SCIFB_TXD, NULL); |
| gpio_request(GPIO_FN_PORT161_SCIFB_CTS_, NULL); |
| gpio_request(GPIO_FN_PORT162_SCIFB_RXD, NULL); |
| gpio_request(GPIO_FN_PORT163_SCIFB_RTS_, NULL); |
| |
| /* SDHI1 (BCM4330) */ |
| gpio_request(GPIO_FN_SDHICLK1, NULL); |
| gpio_request(GPIO_FN_SDHICMD1_PU, NULL); |
| gpio_request(GPIO_FN_SDHID1_3_PU, NULL); |
| gpio_request(GPIO_FN_SDHID1_2_PU, NULL); |
| gpio_request(GPIO_FN_SDHID1_1_PU, NULL); |
| gpio_request(GPIO_FN_SDHID1_0_PU, NULL); |
| |
| #ifdef CONFIG_CACHE_L2X0 |
| /* Early BRESP enable, Shared attribute override enable, 64K*8way */ |
| l2x0_init(__io(0xf0100000), 0x40460000, 0x82000fff); |
| #endif |
| sh73a0_add_standard_devices(); |
| platform_add_devices(kota2_devices, ARRAY_SIZE(kota2_devices)); |
| } |
| |
| static void __init kota2_timer_init(void) |
| { |
| sh73a0_clock_init(); |
| shmobile_timer.init(); |
| return; |
| } |
| |
| struct sys_timer kota2_timer = { |
| .init = kota2_timer_init, |
| }; |
| |
| MACHINE_START(KOTA2, "kota2") |
| .map_io = kota2_map_io, |
| .init_irq = kota2_init_irq, |
| .handle_irq = shmobile_handle_irq_gic, |
| .init_machine = kota2_init, |
| .timer = &kota2_timer, |
| MACHINE_END |