| menu "Kernel hacking" |
| |
| config TRACE_IRQFLAGS_SUPPORT |
| bool |
| default y |
| |
| source "lib/Kconfig.debug" |
| |
| config SH_STANDARD_BIOS |
| bool "Use LinuxSH standard BIOS" |
| help |
| Say Y here if your target has the gdb-sh-stub |
| package from www.m17n.org (or any conforming standard LinuxSH BIOS) |
| in FLASH or EPROM. The kernel will use standard BIOS calls during |
| boot for various housekeeping tasks (including calls to read and |
| write characters to a system console, get a MAC address from an |
| on-board Ethernet interface, and shut down the hardware). Note this |
| does not work with machines with an existing operating system in |
| mask ROM and no flash (WindowsCE machines fall in this category). |
| If unsure, say N. |
| |
| config EARLY_SCIF_CONSOLE |
| bool "Use early SCIF console" |
| help |
| This enables an early console using a fixed SCIF port. This can |
| be used by platforms that are either not running the SH |
| standard BIOS, or do not wish to use the BIOS callbacks for the |
| serial I/O. |
| |
| config EARLY_SCIF_CONSOLE_PORT |
| hex "SCIF port for early console" |
| depends on EARLY_SCIF_CONSOLE |
| default "0xffe00000" if CPU_SUBTYPE_SH7780 |
| default "0xfffe9800" if CPU_SUBTYPE_SH7206 |
| default "0xf8420000" if CPU_SUBTYPE_SH7619 |
| default "0xa4400000" if CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7705 |
| default "0xffe80000" if CPU_SH4 |
| |
| config EARLY_PRINTK |
| bool "Early printk support" |
| depends on SH_STANDARD_BIOS || EARLY_SCIF_CONSOLE |
| help |
| Say Y here to redirect kernel printk messages to the serial port |
| used by the SH-IPL bootloader, starting very early in the boot |
| process and ending when the kernel's serial console is initialised. |
| This option is only useful porting the kernel to a new machine, |
| when the kernel may crash or hang before the serial console is |
| initialised. If unsure, say N. |
| |
| On devices that are running SH-IPL and want to keep the port |
| initialization consistent while not using the BIOS callbacks, |
| select both the EARLY_SCIF_CONSOLE and SH_STANDARD_BIOS, using |
| the kernel command line option to toggle back and forth. |
| |
| config DEBUG_BOOTMEM |
| depends on DEBUG_KERNEL |
| bool "Debug BOOTMEM initialization" |
| |
| config DEBUG_STACKOVERFLOW |
| bool "Check for stack overflows" |
| depends on DEBUG_KERNEL |
| help |
| This option will cause messages to be printed if free stack space |
| drops below a certain limit. |
| |
| config DEBUG_STACK_USAGE |
| bool "Stack utilization instrumentation" |
| depends on DEBUG_KERNEL |
| help |
| Enables the display of the minimum amount of free stack which each |
| task has ever had available in the sysrq-T and sysrq-P debug output. |
| |
| This option will slow down process creation somewhat. |
| |
| config 4KSTACKS |
| bool "Use 4Kb for kernel stacks instead of 8Kb" |
| depends on DEBUG_KERNEL |
| help |
| If you say Y here the kernel will use a 4Kb stacksize for the |
| kernel stack attached to each process/thread. This facilitates |
| running more threads on a system and also reduces the pressure |
| on the VM subsystem for higher order allocations. This option |
| will also use IRQ stacks to compensate for the reduced stackspace. |
| |
| config SH_KGDB |
| bool "Include KGDB kernel debugger" |
| select FRAME_POINTER |
| select DEBUG_INFO |
| help |
| Include in-kernel hooks for kgdb, the Linux kernel source level |
| debugger. See <http://kgdb.sourceforge.net/> for more information. |
| Unless you are intending to debug the kernel, say N here. |
| |
| menu "KGDB configuration options" |
| depends on SH_KGDB |
| |
| config MORE_COMPILE_OPTIONS |
| bool "Add any additional compile options" |
| help |
| If you want to add additional CFLAGS to the kernel build, enable this |
| option and then enter what you would like to add in the next question. |
| Note however that -g is already appended with the selection of KGDB. |
| |
| config COMPILE_OPTIONS |
| string "Additional compile arguments" |
| depends on MORE_COMPILE_OPTIONS |
| |
| config KGDB_NMI |
| bool "Enter KGDB on NMI" |
| default n |
| |
| config SH_KGDB_CONSOLE |
| bool "Console messages through GDB" |
| depends on !SERIAL_SH_SCI_CONSOLE |
| select SERIAL_CORE_CONSOLE |
| default n |
| |
| config KGDB_SYSRQ |
| bool "Allow SysRq 'G' to enter KGDB" |
| default y |
| |
| comment "Serial port setup" |
| |
| config KGDB_DEFPORT |
| int "Port number (ttySCn)" |
| default "1" |
| |
| config KGDB_DEFBAUD |
| int "Baud rate" |
| default "115200" |
| |
| choice |
| prompt "Parity" |
| depends on SH_KGDB |
| default KGDB_DEFPARITY_N |
| |
| config KGDB_DEFPARITY_N |
| bool "None" |
| |
| config KGDB_DEFPARITY_E |
| bool "Even" |
| |
| config KGDB_DEFPARITY_O |
| bool "Odd" |
| |
| endchoice |
| |
| choice |
| prompt "Data bits" |
| depends on SH_KGDB |
| default KGDB_DEFBITS_8 |
| |
| config KGDB_DEFBITS_8 |
| bool "8" |
| |
| config KGDB_DEFBITS_7 |
| bool "7" |
| |
| endchoice |
| |
| endmenu |
| |
| endmenu |
