| /* |
| * Description: keypad driver for ADP5589 |
| * I2C QWERTY Keypad and IO Expander |
| * Bugs: Enter bugs at http://blackfin.uclinux.org/ |
| * |
| * Copyright (C) 2010-2011 Analog Devices Inc. |
| * Licensed under the GPL-2. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/version.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/workqueue.h> |
| #include <linux/errno.h> |
| #include <linux/pm.h> |
| #include <linux/platform_device.h> |
| #include <linux/input.h> |
| #include <linux/i2c.h> |
| #include <linux/gpio.h> |
| #include <linux/slab.h> |
| |
| #include <linux/input/adp5589.h> |
| |
| /* GENERAL_CFG Register */ |
| #define OSC_EN (1 << 7) |
| #define CORE_CLK(x) (((x) & 0x3) << 5) |
| #define LCK_TRK_LOGIC (1 << 4) |
| #define LCK_TRK_GPI (1 << 3) |
| #define INT_CFG (1 << 1) |
| #define RST_CFG (1 << 0) |
| |
| /* INT_EN Register */ |
| #define LOGIC2_IEN (1 << 5) |
| #define LOGIC1_IEN (1 << 4) |
| #define LOCK_IEN (1 << 3) |
| #define OVRFLOW_IEN (1 << 2) |
| #define GPI_IEN (1 << 1) |
| #define EVENT_IEN (1 << 0) |
| |
| /* Interrupt Status Register */ |
| #define LOGIC2_INT (1 << 5) |
| #define LOGIC1_INT (1 << 4) |
| #define LOCK_INT (1 << 3) |
| #define OVRFLOW_INT (1 << 2) |
| #define GPI_INT (1 << 1) |
| #define EVENT_INT (1 << 0) |
| |
| /* STATUS Register */ |
| |
| #define LOGIC2_STAT (1 << 7) |
| #define LOGIC1_STAT (1 << 6) |
| #define LOCK_STAT (1 << 5) |
| #define KEC 0xF |
| |
| /* PIN_CONFIG_D Register */ |
| #define C4_EXTEND_CFG (1 << 6) /* RESET2 */ |
| #define R4_EXTEND_CFG (1 << 5) /* RESET1 */ |
| |
| /* LOCK_CFG */ |
| #define LOCK_EN (1 << 0) |
| |
| #define PTIME_MASK 0x3 |
| #define LTIME_MASK 0x3 |
| |
| /* Key Event Register xy */ |
| #define KEY_EV_PRESSED (1 << 7) |
| #define KEY_EV_MASK (0x7F) |
| |
| #define KEYP_MAX_EVENT 16 |
| |
| #define MAXGPIO 19 |
| #define ADP_BANK(offs) ((offs) >> 3) |
| #define ADP_BIT(offs) (1u << ((offs) & 0x7)) |
| |
| struct adp5589_kpad { |
| struct i2c_client *client; |
| struct input_dev *input; |
| unsigned short keycode[ADP5589_KEYMAPSIZE]; |
| const struct adp5589_gpi_map *gpimap; |
| unsigned short gpimapsize; |
| unsigned extend_cfg; |
| #ifdef CONFIG_GPIOLIB |
| unsigned char gpiomap[MAXGPIO]; |
| bool export_gpio; |
| struct gpio_chip gc; |
| struct mutex gpio_lock; /* Protect cached dir, dat_out */ |
| u8 dat_out[3]; |
| u8 dir[3]; |
| #endif |
| }; |
| |
| static int adp5589_read(struct i2c_client *client, u8 reg) |
| { |
| int ret = i2c_smbus_read_byte_data(client, reg); |
| |
| if (ret < 0) |
| dev_err(&client->dev, "Read Error\n"); |
| |
| return ret; |
| } |
| |
| static int adp5589_write(struct i2c_client *client, u8 reg, u8 val) |
| { |
| return i2c_smbus_write_byte_data(client, reg, val); |
| } |
| |
| #ifdef CONFIG_GPIOLIB |
| static int adp5589_gpio_get_value(struct gpio_chip *chip, unsigned off) |
| { |
| struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc); |
| unsigned int bank = ADP_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP_BIT(kpad->gpiomap[off]); |
| |
| return !!(adp5589_read(kpad->client, ADP5589_GPI_STATUS_A + bank) & |
| bit); |
| } |
| |
| static void adp5589_gpio_set_value(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc); |
| unsigned int bank = ADP_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP_BIT(kpad->gpiomap[off]); |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| if (val) |
| kpad->dat_out[bank] |= bit; |
| else |
| kpad->dat_out[bank] &= ~bit; |
| |
| adp5589_write(kpad->client, ADP5589_GPO_DATA_OUT_A + bank, |
| kpad->dat_out[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| } |
| |
| static int adp5589_gpio_direction_input(struct gpio_chip *chip, unsigned off) |
| { |
| struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc); |
| unsigned int bank = ADP_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP_BIT(kpad->gpiomap[off]); |
| int ret; |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| kpad->dir[bank] &= ~bit; |
| ret = adp5589_write(kpad->client, ADP5589_GPIO_DIRECTION_A + bank, |
| kpad->dir[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| |
| return ret; |
| } |
| |
| static int adp5589_gpio_direction_output(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc); |
| unsigned int bank = ADP_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP_BIT(kpad->gpiomap[off]); |
| int ret; |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| kpad->dir[bank] |= bit; |
| |
| if (val) |
| kpad->dat_out[bank] |= bit; |
| else |
| kpad->dat_out[bank] &= ~bit; |
| |
| ret = adp5589_write(kpad->client, ADP5589_GPO_DATA_OUT_A + bank, |
| kpad->dat_out[bank]); |
| ret |= adp5589_write(kpad->client, ADP5589_GPIO_DIRECTION_A + bank, |
| kpad->dir[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| |
| return ret; |
| } |
| |
| static int __devinit adp5589_build_gpiomap(struct adp5589_kpad *kpad, |
| const struct adp5589_kpad_platform_data *pdata) |
| { |
| bool pin_used[MAXGPIO]; |
| int n_unused = 0; |
| int i; |
| |
| memset(pin_used, false, sizeof(pin_used)); |
| |
| for (i = 0; i < MAXGPIO; i++) |
| if (pdata->keypad_en_mask & (1 << i)) |
| pin_used[i] = true; |
| |
| for (i = 0; i < kpad->gpimapsize; i++) |
| pin_used[kpad->gpimap[i].pin - ADP5589_GPI_PIN_BASE] = true; |
| |
| if (kpad->extend_cfg & R4_EXTEND_CFG) |
| pin_used[4] = true; |
| |
| if (kpad->extend_cfg & C4_EXTEND_CFG) |
| pin_used[12] = true; |
| |
| for (i = 0; i < MAXGPIO; i++) |
| if (!pin_used[i]) |
| kpad->gpiomap[n_unused++] = i; |
| |
| return n_unused; |
| } |
| |
| static int __devinit adp5589_gpio_add(struct adp5589_kpad *kpad) |
| { |
| struct device *dev = &kpad->client->dev; |
| const struct adp5589_kpad_platform_data *pdata = dev->platform_data; |
| const struct adp5589_gpio_platform_data *gpio_data = pdata->gpio_data; |
| int i, error; |
| |
| if (!gpio_data) |
| return 0; |
| |
| kpad->gc.ngpio = adp5589_build_gpiomap(kpad, pdata); |
| if (kpad->gc.ngpio == 0) { |
| dev_info(dev, "No unused gpios left to export\n"); |
| return 0; |
| } |
| |
| kpad->export_gpio = true; |
| |
| kpad->gc.direction_input = adp5589_gpio_direction_input; |
| kpad->gc.direction_output = adp5589_gpio_direction_output; |
| kpad->gc.get = adp5589_gpio_get_value; |
| kpad->gc.set = adp5589_gpio_set_value; |
| kpad->gc.can_sleep = 1; |
| |
| kpad->gc.base = gpio_data->gpio_start; |
| kpad->gc.label = kpad->client->name; |
| kpad->gc.owner = THIS_MODULE; |
| |
| mutex_init(&kpad->gpio_lock); |
| |
| error = gpiochip_add(&kpad->gc); |
| if (error) { |
| dev_err(dev, "gpiochip_add failed, err: %d\n", error); |
| return error; |
| } |
| |
| for (i = 0; i <= ADP_BANK(MAXGPIO); i++) { |
| kpad->dat_out[i] = adp5589_read(kpad->client, |
| ADP5589_GPO_DATA_OUT_A + i); |
| kpad->dir[i] = adp5589_read(kpad->client, |
| ADP5589_GPIO_DIRECTION_A + i); |
| } |
| |
| if (gpio_data->setup) { |
| error = gpio_data->setup(kpad->client, |
| kpad->gc.base, kpad->gc.ngpio, |
| gpio_data->context); |
| if (error) |
| dev_warn(dev, "setup failed, %d\n", error); |
| } |
| |
| return 0; |
| } |
| |
| static void __devexit adp5589_gpio_remove(struct adp5589_kpad *kpad) |
| { |
| struct device *dev = &kpad->client->dev; |
| const struct adp5589_kpad_platform_data *pdata = dev->platform_data; |
| const struct adp5589_gpio_platform_data *gpio_data = pdata->gpio_data; |
| int error; |
| |
| if (!kpad->export_gpio) |
| return; |
| |
| if (gpio_data->teardown) { |
| error = gpio_data->teardown(kpad->client, |
| kpad->gc.base, kpad->gc.ngpio, |
| gpio_data->context); |
| if (error) |
| dev_warn(dev, "teardown failed %d\n", error); |
| } |
| |
| error = gpiochip_remove(&kpad->gc); |
| if (error) |
| dev_warn(dev, "gpiochip_remove failed %d\n", error); |
| } |
| #else |
| static inline int adp5589_gpio_add(struct adp5589_kpad *kpad) |
| { |
| return 0; |
| } |
| |
| static inline void adp5589_gpio_remove(struct adp5589_kpad *kpad) |
| { |
| } |
| #endif |
| |
| static void adp5589_report_switches(struct adp5589_kpad *kpad, |
| int key, int key_val) |
| { |
| int i; |
| |
| for (i = 0; i < kpad->gpimapsize; i++) { |
| if (key_val == kpad->gpimap[i].pin) { |
| input_report_switch(kpad->input, |
| kpad->gpimap[i].sw_evt, |
| key & KEY_EV_PRESSED); |
| break; |
| } |
| } |
| } |
| |
| static void adp5589_report_events(struct adp5589_kpad *kpad, int ev_cnt) |
| { |
| int i; |
| |
| for (i = 0; i < ev_cnt; i++) { |
| int key = adp5589_read(kpad->client, ADP5589_FIFO_1 + i); |
| int key_val = key & KEY_EV_MASK; |
| |
| if (key_val >= ADP5589_GPI_PIN_BASE && |
| key_val <= ADP5589_GPI_PIN_END) { |
| adp5589_report_switches(kpad, key, key_val); |
| } else { |
| input_report_key(kpad->input, |
| kpad->keycode[key_val - 1], |
| key & KEY_EV_PRESSED); |
| } |
| } |
| } |
| |
| static irqreturn_t adp5589_irq(int irq, void *handle) |
| { |
| struct adp5589_kpad *kpad = handle; |
| struct i2c_client *client = kpad->client; |
| int status, ev_cnt; |
| |
| status = adp5589_read(client, ADP5589_INT_STATUS); |
| |
| if (status & OVRFLOW_INT) /* Unlikely and should never happen */ |
| dev_err(&client->dev, "Event Overflow Error\n"); |
| |
| if (status & EVENT_INT) { |
| ev_cnt = adp5589_read(client, ADP5589_STATUS) & KEC; |
| if (ev_cnt) { |
| adp5589_report_events(kpad, ev_cnt); |
| input_sync(kpad->input); |
| } |
| } |
| |
| adp5589_write(client, ADP5589_INT_STATUS, status); /* Status is W1C */ |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int __devinit adp5589_get_evcode(struct adp5589_kpad *kpad, unsigned short key) |
| { |
| int i; |
| |
| for (i = 0; i < ADP5589_KEYMAPSIZE; i++) |
| if (key == kpad->keycode[i]) |
| return (i + 1) | KEY_EV_PRESSED; |
| |
| dev_err(&kpad->client->dev, "RESET/UNLOCK key not in keycode map\n"); |
| |
| return -EINVAL; |
| } |
| |
| static int __devinit adp5589_setup(struct adp5589_kpad *kpad) |
| { |
| struct i2c_client *client = kpad->client; |
| const struct adp5589_kpad_platform_data *pdata = |
| client->dev.platform_data; |
| int i, ret; |
| unsigned char evt_mode1 = 0, evt_mode2 = 0, evt_mode3 = 0; |
| unsigned char pull_mask = 0; |
| |
| ret = adp5589_write(client, ADP5589_PIN_CONFIG_A, |
| pdata->keypad_en_mask & 0xFF); |
| ret |= adp5589_write(client, ADP5589_PIN_CONFIG_B, |
| (pdata->keypad_en_mask >> 8) & 0xFF); |
| ret |= adp5589_write(client, ADP5589_PIN_CONFIG_C, |
| (pdata->keypad_en_mask >> 16) & 0xFF); |
| |
| if (pdata->en_keylock) { |
| ret |= adp5589_write(client, ADP5589_UNLOCK1, |
| pdata->unlock_key1); |
| ret |= adp5589_write(client, ADP5589_UNLOCK2, |
| pdata->unlock_key2); |
| ret |= adp5589_write(client, ADP5589_UNLOCK_TIMERS, |
| pdata->unlock_timer & LTIME_MASK); |
| ret |= adp5589_write(client, ADP5589_LOCK_CFG, LOCK_EN); |
| } |
| |
| for (i = 0; i < KEYP_MAX_EVENT; i++) |
| ret |= adp5589_read(client, ADP5589_FIFO_1 + i); |
| |
| for (i = 0; i < pdata->gpimapsize; i++) { |
| unsigned short pin = pdata->gpimap[i].pin; |
| |
| if (pin <= ADP5589_GPI_PIN_ROW_END) { |
| evt_mode1 |= (1 << (pin - ADP5589_GPI_PIN_ROW_BASE)); |
| } else { |
| evt_mode2 |= |
| ((1 << (pin - ADP5589_GPI_PIN_COL_BASE)) & 0xFF); |
| evt_mode3 |= |
| ((1 << (pin - ADP5589_GPI_PIN_COL_BASE)) >> 8); |
| } |
| } |
| |
| if (pdata->gpimapsize) { |
| ret |= adp5589_write(client, ADP5589_GPI_EVENT_EN_A, evt_mode1); |
| ret |= adp5589_write(client, ADP5589_GPI_EVENT_EN_B, evt_mode2); |
| ret |= adp5589_write(client, ADP5589_GPI_EVENT_EN_C, evt_mode3); |
| } |
| |
| if (pdata->pull_dis_mask & pdata->pullup_en_100k & |
| pdata->pullup_en_300k & pdata->pulldown_en_300k) |
| dev_warn(&client->dev, "Conflicting pull resistor config\n"); |
| |
| for (i = 0; i < MAXGPIO; i++) { |
| unsigned val = 0; |
| |
| if (pdata->pullup_en_300k & (1 << i)) |
| val = 0; |
| else if (pdata->pulldown_en_300k & (1 << i)) |
| val = 1; |
| else if (pdata->pullup_en_100k & (1 << i)) |
| val = 2; |
| else if (pdata->pull_dis_mask & (1 << i)) |
| val = 3; |
| |
| pull_mask |= val << (2 * (i & 0x3)); |
| |
| if ((i & 0x3) == 0x3 || i == MAXGPIO - 1) { |
| ret |= adp5589_write(client, |
| ADP5589_RPULL_CONFIG_A + (i >> 2), |
| pull_mask); |
| pull_mask = 0; |
| } |
| } |
| |
| if (pdata->reset1_key_1 && pdata->reset1_key_2 && pdata->reset1_key_3) { |
| ret |= adp5589_write(client, ADP5589_RESET1_EVENT_A, |
| adp5589_get_evcode(kpad, |
| pdata->reset1_key_1)); |
| ret |= adp5589_write(client, ADP5589_RESET1_EVENT_B, |
| adp5589_get_evcode(kpad, |
| pdata->reset1_key_2)); |
| ret |= adp5589_write(client, ADP5589_RESET1_EVENT_C, |
| adp5589_get_evcode(kpad, |
| pdata->reset1_key_3)); |
| kpad->extend_cfg |= R4_EXTEND_CFG; |
| } |
| |
| if (pdata->reset2_key_1 && pdata->reset2_key_2) { |
| ret |= adp5589_write(client, ADP5589_RESET2_EVENT_A, |
| adp5589_get_evcode(kpad, |
| pdata->reset2_key_1)); |
| ret |= adp5589_write(client, ADP5589_RESET2_EVENT_B, |
| adp5589_get_evcode(kpad, |
| pdata->reset2_key_2)); |
| kpad->extend_cfg |= C4_EXTEND_CFG; |
| } |
| |
| if (kpad->extend_cfg) { |
| ret |= adp5589_write(client, ADP5589_RESET_CFG, |
| pdata->reset_cfg); |
| ret |= adp5589_write(client, ADP5589_PIN_CONFIG_D, |
| kpad->extend_cfg); |
| } |
| |
| for (i = 0; i <= ADP_BANK(MAXGPIO); i++) |
| ret |= adp5589_write(client, ADP5589_DEBOUNCE_DIS_A + i, |
| pdata->debounce_dis_mask >> (i * 8)); |
| |
| ret |= adp5589_write(client, ADP5589_POLL_PTIME_CFG, |
| pdata->scan_cycle_time & PTIME_MASK); |
| ret |= adp5589_write(client, ADP5589_INT_STATUS, LOGIC2_INT | |
| LOGIC1_INT | OVRFLOW_INT | LOCK_INT | |
| GPI_INT | EVENT_INT); /* Status is W1C */ |
| |
| ret |= adp5589_write(client, ADP5589_GENERAL_CFG, |
| INT_CFG | OSC_EN | CORE_CLK(3)); |
| ret |= adp5589_write(client, ADP5589_INT_EN, |
| OVRFLOW_IEN | GPI_IEN | EVENT_IEN); |
| |
| if (ret < 0) { |
| dev_err(&client->dev, "Write Error\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void __devinit adp5589_report_switch_state(struct adp5589_kpad *kpad) |
| { |
| int gpi_stat1 = adp5589_read(kpad->client, ADP5589_GPI_STATUS_A); |
| int gpi_stat2 = adp5589_read(kpad->client, ADP5589_GPI_STATUS_B); |
| int gpi_stat3 = adp5589_read(kpad->client, ADP5589_GPI_STATUS_C); |
| int gpi_stat_tmp, pin_loc; |
| int i; |
| |
| for (i = 0; i < kpad->gpimapsize; i++) { |
| unsigned short pin = kpad->gpimap[i].pin; |
| |
| if (pin <= ADP5589_GPI_PIN_ROW_END) { |
| gpi_stat_tmp = gpi_stat1; |
| pin_loc = pin - ADP5589_GPI_PIN_ROW_BASE; |
| } else if ((pin - ADP5589_GPI_PIN_COL_BASE) < 8) { |
| gpi_stat_tmp = gpi_stat2; |
| pin_loc = pin - ADP5589_GPI_PIN_COL_BASE; |
| } else { |
| gpi_stat_tmp = gpi_stat3; |
| pin_loc = pin - ADP5589_GPI_PIN_COL_BASE - 8; |
| } |
| |
| if (gpi_stat_tmp < 0) { |
| dev_err(&kpad->client->dev, |
| "Can't read GPIO_DAT_STAT switch" |
| " %d default to OFF\n", pin); |
| gpi_stat_tmp = 0; |
| } |
| |
| input_report_switch(kpad->input, |
| kpad->gpimap[i].sw_evt, |
| !(gpi_stat_tmp & (1 << pin_loc))); |
| } |
| |
| input_sync(kpad->input); |
| } |
| |
| static int __devinit adp5589_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct adp5589_kpad *kpad; |
| const struct adp5589_kpad_platform_data *pdata; |
| struct input_dev *input; |
| unsigned int revid; |
| int ret, i; |
| int error; |
| |
| if (!i2c_check_functionality(client->adapter, |
| I2C_FUNC_SMBUS_BYTE_DATA)) { |
| dev_err(&client->dev, "SMBUS Byte Data not Supported\n"); |
| return -EIO; |
| } |
| |
| pdata = client->dev.platform_data; |
| if (!pdata) { |
| dev_err(&client->dev, "no platform data?\n"); |
| return -EINVAL; |
| } |
| |
| if (!((pdata->keypad_en_mask & 0xFF) && |
| (pdata->keypad_en_mask >> 8)) || !pdata->keymap) { |
| dev_err(&client->dev, "no rows, cols or keymap from pdata\n"); |
| return -EINVAL; |
| } |
| |
| if (pdata->keymapsize != ADP5589_KEYMAPSIZE) { |
| dev_err(&client->dev, "invalid keymapsize\n"); |
| return -EINVAL; |
| } |
| |
| if (!pdata->gpimap && pdata->gpimapsize) { |
| dev_err(&client->dev, "invalid gpimap from pdata\n"); |
| return -EINVAL; |
| } |
| |
| if (pdata->gpimapsize > ADP5589_GPIMAPSIZE_MAX) { |
| dev_err(&client->dev, "invalid gpimapsize\n"); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < pdata->gpimapsize; i++) { |
| unsigned short pin = pdata->gpimap[i].pin; |
| |
| if (pin < ADP5589_GPI_PIN_BASE || pin > ADP5589_GPI_PIN_END) { |
| dev_err(&client->dev, "invalid gpi pin data\n"); |
| return -EINVAL; |
| } |
| |
| if ((1 << (pin - ADP5589_GPI_PIN_ROW_BASE)) & |
| pdata->keypad_en_mask) { |
| dev_err(&client->dev, "invalid gpi row/col data\n"); |
| return -EINVAL; |
| } |
| } |
| |
| if (!client->irq) { |
| dev_err(&client->dev, "no IRQ?\n"); |
| return -EINVAL; |
| } |
| |
| kpad = kzalloc(sizeof(*kpad), GFP_KERNEL); |
| input = input_allocate_device(); |
| if (!kpad || !input) { |
| error = -ENOMEM; |
| goto err_free_mem; |
| } |
| |
| kpad->client = client; |
| kpad->input = input; |
| |
| ret = adp5589_read(client, ADP5589_ID); |
| if (ret < 0) { |
| error = ret; |
| goto err_free_mem; |
| } |
| |
| revid = (u8) ret & ADP5589_DEVICE_ID_MASK; |
| |
| input->name = client->name; |
| input->phys = "adp5589-keys/input0"; |
| input->dev.parent = &client->dev; |
| |
| input_set_drvdata(input, kpad); |
| |
| input->id.bustype = BUS_I2C; |
| input->id.vendor = 0x0001; |
| input->id.product = 0x0001; |
| input->id.version = revid; |
| |
| input->keycodesize = sizeof(kpad->keycode[0]); |
| input->keycodemax = pdata->keymapsize; |
| input->keycode = kpad->keycode; |
| |
| memcpy(kpad->keycode, pdata->keymap, |
| pdata->keymapsize * input->keycodesize); |
| |
| kpad->gpimap = pdata->gpimap; |
| kpad->gpimapsize = pdata->gpimapsize; |
| |
| /* setup input device */ |
| __set_bit(EV_KEY, input->evbit); |
| |
| if (pdata->repeat) |
| __set_bit(EV_REP, input->evbit); |
| |
| for (i = 0; i < input->keycodemax; i++) |
| __set_bit(kpad->keycode[i] & KEY_MAX, input->keybit); |
| __clear_bit(KEY_RESERVED, input->keybit); |
| |
| if (kpad->gpimapsize) |
| __set_bit(EV_SW, input->evbit); |
| for (i = 0; i < kpad->gpimapsize; i++) |
| __set_bit(kpad->gpimap[i].sw_evt, input->swbit); |
| |
| error = input_register_device(input); |
| if (error) { |
| dev_err(&client->dev, "unable to register input device\n"); |
| goto err_free_mem; |
| } |
| |
| error = request_threaded_irq(client->irq, NULL, adp5589_irq, |
| IRQF_TRIGGER_FALLING | IRQF_ONESHOT, |
| client->dev.driver->name, kpad); |
| if (error) { |
| dev_err(&client->dev, "irq %d busy?\n", client->irq); |
| goto err_unreg_dev; |
| } |
| |
| error = adp5589_setup(kpad); |
| if (error) |
| goto err_free_irq; |
| |
| if (kpad->gpimapsize) |
| adp5589_report_switch_state(kpad); |
| |
| error = adp5589_gpio_add(kpad); |
| if (error) |
| goto err_free_irq; |
| |
| device_init_wakeup(&client->dev, 1); |
| i2c_set_clientdata(client, kpad); |
| |
| dev_info(&client->dev, "Rev.%d keypad, irq %d\n", revid, client->irq); |
| return 0; |
| |
| err_free_irq: |
| free_irq(client->irq, kpad); |
| err_unreg_dev: |
| input_unregister_device(input); |
| input = NULL; |
| err_free_mem: |
| input_free_device(input); |
| kfree(kpad); |
| |
| return error; |
| } |
| |
| static int __devexit adp5589_remove(struct i2c_client *client) |
| { |
| struct adp5589_kpad *kpad = i2c_get_clientdata(client); |
| |
| adp5589_write(client, ADP5589_GENERAL_CFG, 0); |
| free_irq(client->irq, kpad); |
| input_unregister_device(kpad->input); |
| adp5589_gpio_remove(kpad); |
| kfree(kpad); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int adp5589_suspend(struct device *dev) |
| { |
| struct adp5589_kpad *kpad = dev_get_drvdata(dev); |
| struct i2c_client *client = kpad->client; |
| |
| disable_irq(client->irq); |
| |
| if (device_may_wakeup(&client->dev)) |
| enable_irq_wake(client->irq); |
| |
| return 0; |
| } |
| |
| static int adp5589_resume(struct device *dev) |
| { |
| struct adp5589_kpad *kpad = dev_get_drvdata(dev); |
| struct i2c_client *client = kpad->client; |
| |
| if (device_may_wakeup(&client->dev)) |
| disable_irq_wake(client->irq); |
| |
| enable_irq(client->irq); |
| |
| return 0; |
| } |
| #endif |
| |
| static SIMPLE_DEV_PM_OPS(adp5589_dev_pm_ops, adp5589_suspend, adp5589_resume); |
| |
| static const struct i2c_device_id adp5589_id[] = { |
| {"adp5589-keys", 0}, |
| {} |
| }; |
| |
| MODULE_DEVICE_TABLE(i2c, adp5589_id); |
| |
| static struct i2c_driver adp5589_driver = { |
| .driver = { |
| .name = KBUILD_MODNAME, |
| .owner = THIS_MODULE, |
| .pm = &adp5589_dev_pm_ops, |
| }, |
| .probe = adp5589_probe, |
| .remove = __devexit_p(adp5589_remove), |
| .id_table = adp5589_id, |
| }; |
| |
| static int __init adp5589_init(void) |
| { |
| return i2c_add_driver(&adp5589_driver); |
| } |
| module_init(adp5589_init); |
| |
| static void __exit adp5589_exit(void) |
| { |
| i2c_del_driver(&adp5589_driver); |
| } |
| module_exit(adp5589_exit); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>"); |
| MODULE_DESCRIPTION("ADP5589 Keypad driver"); |