| /* |
| * Touchscreen driver for Sharp SL-C7xx and SL-Cxx00 models |
| * |
| * Copyright (c) 2004-2005 Richard Purdie |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| */ |
| |
| |
| #include <linux/delay.h> |
| #include <linux/platform_device.h> |
| #include <linux/init.h> |
| #include <linux/input.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/slab.h> |
| #include <linux/irq.h> |
| |
| #include <asm/arch/sharpsl.h> |
| #include <asm/arch/hardware.h> |
| #include <asm/arch/pxa-regs.h> |
| |
| |
| #define PWR_MODE_ACTIVE 0 |
| #define PWR_MODE_SUSPEND 1 |
| |
| #define X_AXIS_MAX 3830 |
| #define X_AXIS_MIN 150 |
| #define Y_AXIS_MAX 3830 |
| #define Y_AXIS_MIN 190 |
| #define PRESSURE_MIN 0 |
| #define PRESSURE_MAX 15000 |
| |
| struct ts_event { |
| short pressure; |
| short x; |
| short y; |
| }; |
| |
| struct corgi_ts { |
| struct input_dev *input; |
| struct timer_list timer; |
| struct ts_event tc; |
| int pendown; |
| int power_mode; |
| int irq_gpio; |
| struct corgits_machinfo *machinfo; |
| }; |
| |
| #ifdef CONFIG_PXA25x |
| #define CCNT(a) asm volatile ("mrc p14, 0, %0, C1, C0, 0" : "=r"(a)) |
| #define PMNC_GET(x) asm volatile ("mrc p14, 0, %0, C0, C0, 0" : "=r"(x)) |
| #define PMNC_SET(x) asm volatile ("mcr p14, 0, %0, C0, C0, 0" : : "r"(x)) |
| #endif |
| #ifdef CONFIG_PXA27x |
| #define CCNT(a) asm volatile ("mrc p14, 0, %0, C1, C1, 0" : "=r"(a)) |
| #define PMNC_GET(x) asm volatile ("mrc p14, 0, %0, C0, C1, 0" : "=r"(x)) |
| #define PMNC_SET(x) asm volatile ("mcr p14, 0, %0, C0, C1, 0" : : "r"(x)) |
| #endif |
| |
| /* ADS7846 Touch Screen Controller bit definitions */ |
| #define ADSCTRL_PD0 (1u << 0) /* PD0 */ |
| #define ADSCTRL_PD1 (1u << 1) /* PD1 */ |
| #define ADSCTRL_DFR (1u << 2) /* SER/DFR */ |
| #define ADSCTRL_MOD (1u << 3) /* Mode */ |
| #define ADSCTRL_ADR_SH 4 /* Address setting */ |
| #define ADSCTRL_STS (1u << 7) /* Start Bit */ |
| |
| /* External Functions */ |
| extern unsigned int get_clk_frequency_khz(int info); |
| |
| static unsigned long calc_waittime(struct corgi_ts *corgi_ts) |
| { |
| unsigned long hsync_len = corgi_ts->machinfo->get_hsync_len(); |
| |
| if (hsync_len) |
| return get_clk_frequency_khz(0)*1000/hsync_len; |
| else |
| return 0; |
| } |
| |
| static int sync_receive_data_send_cmd(struct corgi_ts *corgi_ts, int doRecive, int doSend, |
| unsigned int address, unsigned long wait_time) |
| { |
| unsigned long timer1 = 0, timer2, pmnc = 0; |
| int pos = 0; |
| |
| if (wait_time && doSend) { |
| PMNC_GET(pmnc); |
| if (!(pmnc & 0x01)) |
| PMNC_SET(0x01); |
| |
| /* polling HSync */ |
| corgi_ts->machinfo->wait_hsync(); |
| /* get CCNT */ |
| CCNT(timer1); |
| } |
| |
| if (doRecive) |
| pos = corgi_ssp_ads7846_get(); |
| |
| if (doSend) { |
| int cmd = ADSCTRL_PD0 | ADSCTRL_PD1 | (address << ADSCTRL_ADR_SH) | ADSCTRL_STS; |
| /* dummy command */ |
| corgi_ssp_ads7846_put(cmd); |
| corgi_ssp_ads7846_get(); |
| |
| if (wait_time) { |
| /* Wait after HSync */ |
| CCNT(timer2); |
| if (timer2-timer1 > wait_time) { |
| /* too slow - timeout, try again */ |
| corgi_ts->machinfo->wait_hsync(); |
| /* get OSCR */ |
| CCNT(timer1); |
| /* Wait after HSync */ |
| CCNT(timer2); |
| } |
| while (timer2 - timer1 < wait_time) |
| CCNT(timer2); |
| } |
| corgi_ssp_ads7846_put(cmd); |
| if (wait_time && !(pmnc & 0x01)) |
| PMNC_SET(pmnc); |
| } |
| return pos; |
| } |
| |
| static int read_xydata(struct corgi_ts *corgi_ts) |
| { |
| unsigned int x, y, z1, z2; |
| unsigned long flags, wait_time; |
| |
| /* critical section */ |
| local_irq_save(flags); |
| corgi_ssp_ads7846_lock(); |
| wait_time = calc_waittime(corgi_ts); |
| |
| /* Y-axis */ |
| sync_receive_data_send_cmd(corgi_ts, 0, 1, 1u, wait_time); |
| |
| /* Y-axis */ |
| sync_receive_data_send_cmd(corgi_ts, 1, 1, 1u, wait_time); |
| |
| /* X-axis */ |
| y = sync_receive_data_send_cmd(corgi_ts, 1, 1, 5u, wait_time); |
| |
| /* Z1 */ |
| x = sync_receive_data_send_cmd(corgi_ts, 1, 1, 3u, wait_time); |
| |
| /* Z2 */ |
| z1 = sync_receive_data_send_cmd(corgi_ts, 1, 1, 4u, wait_time); |
| z2 = sync_receive_data_send_cmd(corgi_ts, 1, 0, 4u, wait_time); |
| |
| /* Power-Down Enable */ |
| corgi_ssp_ads7846_put((1u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| corgi_ssp_ads7846_get(); |
| |
| corgi_ssp_ads7846_unlock(); |
| local_irq_restore(flags); |
| |
| if (x== 0 || y == 0 || z1 == 0 || (x * (z2 - z1) / z1) >= 15000) { |
| corgi_ts->tc.pressure = 0; |
| return 0; |
| } |
| |
| corgi_ts->tc.x = x; |
| corgi_ts->tc.y = y; |
| corgi_ts->tc.pressure = (x * (z2 - z1)) / z1; |
| return 1; |
| } |
| |
| static void new_data(struct corgi_ts *corgi_ts, struct pt_regs *regs) |
| { |
| if (corgi_ts->power_mode != PWR_MODE_ACTIVE) |
| return; |
| |
| if (!corgi_ts->tc.pressure && corgi_ts->pendown == 0) |
| return; |
| |
| input_regs(corgi_ts->input, regs); |
| input_report_abs(corgi_ts->input, ABS_X, corgi_ts->tc.x); |
| input_report_abs(corgi_ts->input, ABS_Y, corgi_ts->tc.y); |
| input_report_abs(corgi_ts->input, ABS_PRESSURE, corgi_ts->tc.pressure); |
| input_report_key(corgi_ts->input, BTN_TOUCH, (corgi_ts->pendown != 0)); |
| input_sync(corgi_ts->input); |
| } |
| |
| static void ts_interrupt_main(struct corgi_ts *corgi_ts, int isTimer, struct pt_regs *regs) |
| { |
| if ((GPLR(IRQ_TO_GPIO(corgi_ts->irq_gpio)) & GPIO_bit(IRQ_TO_GPIO(corgi_ts->irq_gpio))) == 0) { |
| /* Disable Interrupt */ |
| set_irq_type(corgi_ts->irq_gpio, IRQT_NOEDGE); |
| if (read_xydata(corgi_ts)) { |
| corgi_ts->pendown = 1; |
| new_data(corgi_ts, regs); |
| } |
| mod_timer(&corgi_ts->timer, jiffies + HZ / 100); |
| } else { |
| if (corgi_ts->pendown == 1 || corgi_ts->pendown == 2) { |
| mod_timer(&corgi_ts->timer, jiffies + HZ / 100); |
| corgi_ts->pendown++; |
| return; |
| } |
| |
| if (corgi_ts->pendown) { |
| corgi_ts->tc.pressure = 0; |
| new_data(corgi_ts, regs); |
| } |
| |
| /* Enable Falling Edge */ |
| set_irq_type(corgi_ts->irq_gpio, IRQT_FALLING); |
| corgi_ts->pendown = 0; |
| } |
| } |
| |
| static void corgi_ts_timer(unsigned long data) |
| { |
| struct corgi_ts *corgits_data = (struct corgi_ts *) data; |
| ts_interrupt_main(corgits_data, 1, NULL); |
| } |
| |
| static irqreturn_t ts_interrupt(int irq, void *dev_id, struct pt_regs *regs) |
| { |
| struct corgi_ts *corgits_data = dev_id; |
| ts_interrupt_main(corgits_data, 0, regs); |
| return IRQ_HANDLED; |
| } |
| |
| #ifdef CONFIG_PM |
| static int corgits_suspend(struct platform_device *dev, pm_message_t state) |
| { |
| struct corgi_ts *corgi_ts = platform_get_drvdata(dev); |
| |
| if (corgi_ts->pendown) { |
| del_timer_sync(&corgi_ts->timer); |
| corgi_ts->tc.pressure = 0; |
| new_data(corgi_ts, NULL); |
| corgi_ts->pendown = 0; |
| } |
| corgi_ts->power_mode = PWR_MODE_SUSPEND; |
| |
| corgi_ssp_ads7846_putget((1u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| |
| return 0; |
| } |
| |
| static int corgits_resume(struct platform_device *dev) |
| { |
| struct corgi_ts *corgi_ts = platform_get_drvdata(dev); |
| |
| corgi_ssp_ads7846_putget((4u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| /* Enable Falling Edge */ |
| set_irq_type(corgi_ts->irq_gpio, IRQT_FALLING); |
| corgi_ts->power_mode = PWR_MODE_ACTIVE; |
| |
| return 0; |
| } |
| #else |
| #define corgits_suspend NULL |
| #define corgits_resume NULL |
| #endif |
| |
| static int __init corgits_probe(struct platform_device *pdev) |
| { |
| struct corgi_ts *corgi_ts; |
| struct input_dev *input_dev; |
| int err = -ENOMEM; |
| |
| corgi_ts = kzalloc(sizeof(struct corgi_ts), GFP_KERNEL); |
| input_dev = input_allocate_device(); |
| if (!corgi_ts || !input_dev) |
| goto fail; |
| |
| platform_set_drvdata(pdev, corgi_ts); |
| |
| corgi_ts->machinfo = pdev->dev.platform_data; |
| corgi_ts->irq_gpio = platform_get_irq(pdev, 0); |
| |
| if (corgi_ts->irq_gpio < 0) { |
| err = -ENODEV; |
| goto fail; |
| } |
| |
| corgi_ts->input = input_dev; |
| |
| init_timer(&corgi_ts->timer); |
| corgi_ts->timer.data = (unsigned long) corgi_ts; |
| corgi_ts->timer.function = corgi_ts_timer; |
| |
| input_dev->name = "Corgi Touchscreen"; |
| input_dev->phys = "corgits/input0"; |
| input_dev->id.bustype = BUS_HOST; |
| input_dev->id.vendor = 0x0001; |
| input_dev->id.product = 0x0002; |
| input_dev->id.version = 0x0100; |
| input_dev->cdev.dev = &pdev->dev; |
| input_dev->private = corgi_ts; |
| |
| input_dev->evbit[0] = BIT(EV_KEY) | BIT(EV_ABS); |
| input_dev->keybit[LONG(BTN_TOUCH)] = BIT(BTN_TOUCH); |
| input_set_abs_params(input_dev, ABS_X, X_AXIS_MIN, X_AXIS_MAX, 0, 0); |
| input_set_abs_params(input_dev, ABS_Y, Y_AXIS_MIN, Y_AXIS_MAX, 0, 0); |
| input_set_abs_params(input_dev, ABS_PRESSURE, PRESSURE_MIN, PRESSURE_MAX, 0, 0); |
| |
| pxa_gpio_mode(IRQ_TO_GPIO(corgi_ts->irq_gpio) | GPIO_IN); |
| |
| /* Initiaize ADS7846 Difference Reference mode */ |
| corgi_ssp_ads7846_putget((1u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| mdelay(5); |
| corgi_ssp_ads7846_putget((3u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| mdelay(5); |
| corgi_ssp_ads7846_putget((4u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| mdelay(5); |
| corgi_ssp_ads7846_putget((5u << ADSCTRL_ADR_SH) | ADSCTRL_STS); |
| mdelay(5); |
| |
| if (request_irq(corgi_ts->irq_gpio, ts_interrupt, IRQF_DISABLED, "ts", corgi_ts)) { |
| err = -EBUSY; |
| goto fail; |
| } |
| |
| input_register_device(corgi_ts->input); |
| |
| corgi_ts->power_mode = PWR_MODE_ACTIVE; |
| |
| /* Enable Falling Edge */ |
| set_irq_type(corgi_ts->irq_gpio, IRQT_FALLING); |
| |
| return 0; |
| |
| fail: input_free_device(input_dev); |
| kfree(corgi_ts); |
| return err; |
| |
| } |
| |
| static int corgits_remove(struct platform_device *pdev) |
| { |
| struct corgi_ts *corgi_ts = platform_get_drvdata(pdev); |
| |
| free_irq(corgi_ts->irq_gpio, NULL); |
| del_timer_sync(&corgi_ts->timer); |
| corgi_ts->machinfo->put_hsync(); |
| input_unregister_device(corgi_ts->input); |
| kfree(corgi_ts); |
| return 0; |
| } |
| |
| static struct platform_driver corgits_driver = { |
| .probe = corgits_probe, |
| .remove = corgits_remove, |
| .suspend = corgits_suspend, |
| .resume = corgits_resume, |
| .driver = { |
| .name = "corgi-ts", |
| }, |
| }; |
| |
| static int __devinit corgits_init(void) |
| { |
| return platform_driver_register(&corgits_driver); |
| } |
| |
| static void __exit corgits_exit(void) |
| { |
| platform_driver_unregister(&corgits_driver); |
| } |
| |
| module_init(corgits_init); |
| module_exit(corgits_exit); |
| |
| MODULE_AUTHOR("Richard Purdie <rpurdie@rpsys.net>"); |
| MODULE_DESCRIPTION("Corgi TouchScreen Driver"); |
| MODULE_LICENSE("GPL"); |