blob: abf7b6153d00b8527b997e4e947b48a63449af4b [file] [log] [blame]
/*
* drivers/net/phy/micrel.c
*
* Driver for Micrel PHYs
*
* Author: David J. Choi
*
* Copyright (c) 2010-2013 Micrel, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* Support : Micrel Phys:
* Giga phys: ksz9021, ksz9031
* 100/10 Phys : ksz8001, ksz8721, ksz8737, ksz8041
* ksz8021, ksz8031, ksz8051,
* ksz8081, ksz8091,
* ksz8061,
* Switch : ksz8873, ksz886x
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/micrel_phy.h>
/* Operation Mode Strap Override */
#define MII_KSZPHY_OMSO 0x16
#define KSZPHY_OMSO_B_CAST_OFF (1 << 9)
#define KSZPHY_OMSO_RMII_OVERRIDE (1 << 1)
#define KSZPHY_OMSO_MII_OVERRIDE (1 << 0)
/* general Interrupt control/status reg in vendor specific block. */
#define MII_KSZPHY_INTCS 0x1B
#define KSZPHY_INTCS_JABBER (1 << 15)
#define KSZPHY_INTCS_RECEIVE_ERR (1 << 14)
#define KSZPHY_INTCS_PAGE_RECEIVE (1 << 13)
#define KSZPHY_INTCS_PARELLEL (1 << 12)
#define KSZPHY_INTCS_LINK_PARTNER_ACK (1 << 11)
#define KSZPHY_INTCS_LINK_DOWN (1 << 10)
#define KSZPHY_INTCS_REMOTE_FAULT (1 << 9)
#define KSZPHY_INTCS_LINK_UP (1 << 8)
#define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\
KSZPHY_INTCS_LINK_DOWN)
/* general PHY control reg in vendor specific block. */
#define MII_KSZPHY_CTRL 0x1F
/* bitmap of PHY register to set interrupt mode */
#define KSZPHY_CTRL_INT_ACTIVE_HIGH (1 << 9)
#define KSZ9021_CTRL_INT_ACTIVE_HIGH (1 << 14)
#define KS8737_CTRL_INT_ACTIVE_HIGH (1 << 14)
#define KSZ8051_RMII_50MHZ_CLK (1 << 7)
static int kszphy_ack_interrupt(struct phy_device *phydev)
{
/* bit[7..0] int status, which is a read and clear register. */
int rc;
rc = phy_read(phydev, MII_KSZPHY_INTCS);
return (rc < 0) ? rc : 0;
}
static int kszphy_set_interrupt(struct phy_device *phydev)
{
int temp;
temp = (PHY_INTERRUPT_ENABLED == phydev->interrupts) ?
KSZPHY_INTCS_ALL : 0;
return phy_write(phydev, MII_KSZPHY_INTCS, temp);
}
static int kszphy_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KSZPHY_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int ksz9021_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KSZ9021_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int ks8737_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KS8737_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int kszphy_config_init(struct phy_device *phydev)
{
return 0;
}
static int ksz8021_config_init(struct phy_device *phydev)
{
const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE;
phy_write(phydev, MII_KSZPHY_OMSO, val);
return 0;
}
static int ks8051_config_init(struct phy_device *phydev)
{
int regval;
if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) {
regval = phy_read(phydev, MII_KSZPHY_CTRL);
regval |= KSZ8051_RMII_50MHZ_CLK;
phy_write(phydev, MII_KSZPHY_CTRL, regval);
}
return 0;
}
#define KSZ8873MLL_GLOBAL_CONTROL_4 0x06
#define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX (1 << 6)
#define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED (1 << 4)
int ksz8873mll_read_status(struct phy_device *phydev)
{
int regval;
/* dummy read */
regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4);
regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4);
if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX)
phydev->duplex = DUPLEX_HALF;
else
phydev->duplex = DUPLEX_FULL;
if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_SPEED)
phydev->speed = SPEED_10;
else
phydev->speed = SPEED_100;
phydev->link = 1;
phydev->pause = phydev->asym_pause = 0;
return 0;
}
static int ksz8873mll_config_aneg(struct phy_device *phydev)
{
return 0;
}
static struct phy_driver ksphy_driver[] = {
{
.phy_id = PHY_ID_KS8737,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KS8737",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ks8737_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8021,
.phy_id_mask = 0x00ffffff,
.name = "Micrel KSZ8021 or KSZ8031",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = ksz8021_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8041,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8041",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause
| SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8051,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8051",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause
| SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = ks8051_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8001,
.name = "Micrel KSZ8001 or KS8721",
.phy_id_mask = 0x00ffffff,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8081,
.name = "Micrel KSZ8081 or KSZ8091",
.phy_id_mask = 0x00fffff0,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8061,
.name = "Micrel KSZ8061",
.phy_id_mask = 0x00fffff0,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ9021,
.phy_id_mask = 0x000ffffe,
.name = "Micrel KSZ9021 Gigabit PHY",
.features = (PHY_GBIT_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ksz9021_config_intr,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ9031,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ9031 Gigabit PHY",
.features = (PHY_GBIT_FEATURES | SUPPORTED_Pause
| SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ksz9021_config_intr,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ8873MLL,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8873MLL Switch",
.features = (SUPPORTED_Pause | SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG,
.config_init = kszphy_config_init,
.config_aneg = ksz8873mll_config_aneg,
.read_status = ksz8873mll_read_status,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ886X,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ886X Switch",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.driver = { .owner = THIS_MODULE, },
} };
static int __init ksphy_init(void)
{
return phy_drivers_register(ksphy_driver,
ARRAY_SIZE(ksphy_driver));
}
static void __exit ksphy_exit(void)
{
phy_drivers_unregister(ksphy_driver,
ARRAY_SIZE(ksphy_driver));
}
module_init(ksphy_init);
module_exit(ksphy_exit);
MODULE_DESCRIPTION("Micrel PHY driver");
MODULE_AUTHOR("David J. Choi");
MODULE_LICENSE("GPL");
static struct mdio_device_id __maybe_unused micrel_tbl[] = {
{ PHY_ID_KSZ9021, 0x000ffffe },
{ PHY_ID_KSZ9031, 0x00fffff0 },
{ PHY_ID_KSZ8001, 0x00ffffff },
{ PHY_ID_KS8737, 0x00fffff0 },
{ PHY_ID_KSZ8021, 0x00ffffff },
{ PHY_ID_KSZ8041, 0x00fffff0 },
{ PHY_ID_KSZ8051, 0x00fffff0 },
{ PHY_ID_KSZ8061, 0x00fffff0 },
{ PHY_ID_KSZ8081, 0x00fffff0 },
{ PHY_ID_KSZ8873MLL, 0x00fffff0 },
{ PHY_ID_KSZ886X, 0x00fffff0 },
{ }
};
MODULE_DEVICE_TABLE(mdio, micrel_tbl);