Merge tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 3.12-rc3.
These are all for host controller issues that have been reported, and
there's a fix for an annoying error message that gets printed every
time you remove a USB 3 device from the system that's been bugging me
for a while"
* tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: add support for Merrifield
USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
USB: Fix breakage in ffs_fs_mount()
fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
usb: chipidea: USB_CHIPIDEA should depend on HAS_DMA
usb: chipidea: udc: free pending TD at removal procedure
usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
usb: chipidea: Fix memleak for ci->hw_bank.regmap when removal
usb: chipidea: udc: fix the oops after rmmod gadget
USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
USB: OHCI: accept very late isochronous URBs
USB: UHCI: accept very late isochronous URBs
USB: iMX21: accept very late isochronous URBs
usbcore: check usb device's state before sending a Set SEL control transfer
xhci: Fix race between ep halt and URB cancellation
usb: Fix xHCI host issues on remote wakeup.
xhci: Ensure a command structure points to the correct trb on the command ring
xhci: Fix oops happening after address device timeout
diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig
index 4a851e1..77b47d8 100644
--- a/drivers/usb/chipidea/Kconfig
+++ b/drivers/usb/chipidea/Kconfig
@@ -1,6 +1,6 @@
config USB_CHIPIDEA
tristate "ChipIdea Highspeed Dual Role Controller"
- depends on (USB_EHCI_HCD && USB_GADGET) || (USB_EHCI_HCD && !USB_GADGET) || (!USB_EHCI_HCD && USB_GADGET)
+ depends on ((USB_EHCI_HCD && USB_GADGET) || (USB_EHCI_HCD && !USB_GADGET) || (!USB_EHCI_HCD && USB_GADGET)) && HAS_DMA
help
Say Y here if your system has a dual role high speed USB
controller based on ChipIdea silicon IP. Currently, only the
diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c b/drivers/usb/chipidea/ci_hdrc_imx.c
index 74d998d..be822a2 100644
--- a/drivers/usb/chipidea/ci_hdrc_imx.c
+++ b/drivers/usb/chipidea/ci_hdrc_imx.c
@@ -131,7 +131,7 @@
if (ret) {
dev_err(&pdev->dev, "usbmisc init failed, ret=%d\n",
ret);
- goto err_clk;
+ goto err_phy;
}
}
@@ -143,7 +143,7 @@
dev_err(&pdev->dev,
"Can't register ci_hdrc platform device, err=%d\n",
ret);
- goto err_clk;
+ goto err_phy;
}
if (data->usbmisc_data) {
@@ -164,6 +164,9 @@
disable_device:
ci_hdrc_remove_device(data->ci_pdev);
+err_phy:
+ if (data->phy)
+ usb_phy_shutdown(data->phy);
err_clk:
clk_disable_unprepare(data->clk);
return ret;
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 9462640..23763dc 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -605,6 +605,7 @@
dbg_remove_files(ci);
free_irq(ci->irq, ci);
ci_role_destroy(ci);
+ kfree(ci->hw_bank.regmap);
return 0;
}
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index 6b4c2f2..9333083 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -1600,6 +1600,8 @@
for (i = 0; i < ci->hw_ep_max; i++) {
struct ci_hw_ep *hwep = &ci->ci_hw_ep[i];
+ if (hwep->pending_td)
+ free_pending_td(hwep);
dma_pool_free(ci->qh_pool, hwep->qh.ptr, hwep->qh.dma);
}
}
@@ -1667,13 +1669,13 @@
if (ci->platdata->notify_event)
ci->platdata->notify_event(ci,
CI_HDRC_CONTROLLER_STOPPED_EVENT);
- ci->driver = NULL;
spin_unlock_irqrestore(&ci->lock, flags);
_gadget_stop_activity(&ci->gadget);
spin_lock_irqsave(&ci->lock, flags);
pm_runtime_put(&ci->gadget.dev);
}
+ ci->driver = NULL;
spin_unlock_irqrestore(&ci->lock, flags);
return 0;
diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index 737e3c1..71dc5d7 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -742,6 +742,22 @@
if ((index & ~USB_DIR_IN) == 0)
return 0;
ret = findintfep(ps->dev, index);
+ if (ret < 0) {
+ /*
+ * Some not fully compliant Win apps seem to get
+ * index wrong and have the endpoint number here
+ * rather than the endpoint address (with the
+ * correct direction). Win does let this through,
+ * so we'll not reject it here but leave it to
+ * the device to not break KVM. But we warn.
+ */
+ ret = findintfep(ps->dev, index ^ 0x80);
+ if (ret >= 0)
+ dev_info(&ps->dev->dev,
+ "%s: process %i (%s) requesting ep %02x but needs %02x\n",
+ __func__, task_pid_nr(current),
+ current->comm, index, index ^ 0x80);
+ }
if (ret >= 0)
ret = checkintf(ps, ret);
break;
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index dde4c83..e6b682c 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -3426,6 +3426,9 @@
unsigned long long u2_pel;
int ret;
+ if (udev->state != USB_STATE_CONFIGURED)
+ return 0;
+
/* Convert SEL and PEL stored in ns to us */
u1_sel = DIV_ROUND_UP(udev->u1_params.sel, 1000);
u1_pel = DIV_ROUND_UP(udev->u1_params.pel, 1000);
diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c
index 997ebe4..2e252aa 100644
--- a/drivers/usb/dwc3/dwc3-pci.c
+++ b/drivers/usb/dwc3/dwc3-pci.c
@@ -29,6 +29,7 @@
#define PCI_VENDOR_ID_SYNOPSYS 0x16c3
#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3 0xabcd
#define PCI_DEVICE_ID_INTEL_BYT 0x0f37
+#define PCI_DEVICE_ID_INTEL_MRFLD 0x119e
struct dwc3_pci {
struct device *dev;
@@ -189,6 +190,7 @@
PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3),
},
{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BYT), },
+ { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MRFLD), },
{ } /* Terminating Entry */
};
MODULE_DEVICE_TABLE(pci, dwc3_pci_id_table);
diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c
index 1a66c5b..0658908 100644
--- a/drivers/usb/gadget/f_fs.c
+++ b/drivers/usb/gadget/f_fs.c
@@ -1034,37 +1034,19 @@
struct ffs_file_perms perms;
umode_t root_mode;
const char *dev_name;
- union {
- /* set by ffs_fs_mount(), read by ffs_sb_fill() */
- void *private_data;
- /* set by ffs_sb_fill(), read by ffs_fs_mount */
- struct ffs_data *ffs_data;
- };
+ struct ffs_data *ffs_data;
};
static int ffs_sb_fill(struct super_block *sb, void *_data, int silent)
{
struct ffs_sb_fill_data *data = _data;
struct inode *inode;
- struct ffs_data *ffs;
+ struct ffs_data *ffs = data->ffs_data;
ENTER();
- /* Initialise data */
- ffs = ffs_data_new();
- if (unlikely(!ffs))
- goto Enomem;
-
ffs->sb = sb;
- ffs->dev_name = kstrdup(data->dev_name, GFP_KERNEL);
- if (unlikely(!ffs->dev_name))
- goto Enomem;
- ffs->file_perms = data->perms;
- ffs->private_data = data->private_data;
-
- /* used by the caller of this function */
- data->ffs_data = ffs;
-
+ data->ffs_data = NULL;
sb->s_fs_info = ffs;
sb->s_blocksize = PAGE_CACHE_SIZE;
sb->s_blocksize_bits = PAGE_CACHE_SHIFT;
@@ -1080,17 +1062,14 @@
&data->perms);
sb->s_root = d_make_root(inode);
if (unlikely(!sb->s_root))
- goto Enomem;
+ return -ENOMEM;
/* EP0 file */
if (unlikely(!ffs_sb_create_file(sb, "ep0", ffs,
&ffs_ep0_operations, NULL)))
- goto Enomem;
+ return -ENOMEM;
return 0;
-
-Enomem:
- return -ENOMEM;
}
static int ffs_fs_parse_opts(struct ffs_sb_fill_data *data, char *opts)
@@ -1193,6 +1172,7 @@
struct dentry *rv;
int ret;
void *ffs_dev;
+ struct ffs_data *ffs;
ENTER();
@@ -1200,18 +1180,30 @@
if (unlikely(ret < 0))
return ERR_PTR(ret);
+ ffs = ffs_data_new();
+ if (unlikely(!ffs))
+ return ERR_PTR(-ENOMEM);
+ ffs->file_perms = data.perms;
+
+ ffs->dev_name = kstrdup(dev_name, GFP_KERNEL);
+ if (unlikely(!ffs->dev_name)) {
+ ffs_data_put(ffs);
+ return ERR_PTR(-ENOMEM);
+ }
+
ffs_dev = functionfs_acquire_dev_callback(dev_name);
- if (IS_ERR(ffs_dev))
- return ffs_dev;
+ if (IS_ERR(ffs_dev)) {
+ ffs_data_put(ffs);
+ return ERR_CAST(ffs_dev);
+ }
+ ffs->private_data = ffs_dev;
+ data.ffs_data = ffs;
- data.dev_name = dev_name;
- data.private_data = ffs_dev;
rv = mount_nodev(t, flags, &data, ffs_sb_fill);
-
- /* data.ffs_data is set by ffs_sb_fill */
- if (IS_ERR(rv))
+ if (IS_ERR(rv) && data.ffs_data) {
functionfs_release_dev_callback(data.ffs_data);
-
+ ffs_data_put(data.ffs_data);
+ }
return rv;
}
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 4449f56..f2407b2 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -130,7 +130,7 @@
}
/* Enable USB controller, 83xx or 8536 */
- if (pdata->have_sysif_regs)
+ if (pdata->have_sysif_regs && pdata->controller_ver < FSL_USB_VER_1_6)
setbits32(hcd->regs + FSL_SOC_USB_CTRL, 0x4);
/* Don't need to set host mode here. It will be done by tdi_reset() */
@@ -232,15 +232,9 @@
case FSL_USB2_PHY_ULPI:
if (pdata->have_sysif_regs && pdata->controller_ver) {
/* controller version 1.6 or above */
+ clrbits32(non_ehci + FSL_SOC_USB_CTRL, UTMI_PHY_EN);
setbits32(non_ehci + FSL_SOC_USB_CTRL,
- ULPI_PHY_CLK_SEL);
- /*
- * Due to controller issue of PHY_CLK_VALID in ULPI
- * mode, we set USB_CTRL_USB_EN before checking
- * PHY_CLK_VALID, otherwise PHY_CLK_VALID doesn't work.
- */
- clrsetbits_be32(non_ehci + FSL_SOC_USB_CTRL,
- UTMI_PHY_EN, USB_CTRL_USB_EN);
+ ULPI_PHY_CLK_SEL | USB_CTRL_USB_EN);
}
portsc |= PORT_PTS_ULPI;
break;
@@ -270,8 +264,9 @@
if (pdata->have_sysif_regs && pdata->controller_ver &&
(phy_mode == FSL_USB2_PHY_ULPI)) {
/* check PHY_CLK_VALID to get phy clk valid */
- if (!spin_event_timeout(in_be32(non_ehci + FSL_SOC_USB_CTRL) &
- PHY_CLK_VALID, FSL_USB_PHY_CLK_TIMEOUT, 0)) {
+ if (!(spin_event_timeout(in_be32(non_ehci + FSL_SOC_USB_CTRL) &
+ PHY_CLK_VALID, FSL_USB_PHY_CLK_TIMEOUT, 0) ||
+ in_be32(non_ehci + FSL_SOC_USB_PRICTRL))) {
printk(KERN_WARNING "fsl-ehci: USB PHY clock invalid\n");
return -EINVAL;
}
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 6bd299e..854c2ec 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -361,7 +361,7 @@
.remove = usb_hcd_pci_remove,
.shutdown = usb_hcd_pci_shutdown,
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
.driver = {
.pm = &usb_hcd_pci_pm_ops
},
diff --git a/drivers/usb/host/imx21-hcd.c b/drivers/usb/host/imx21-hcd.c
index 60a5de5..adb01d9 100644
--- a/drivers/usb/host/imx21-hcd.c
+++ b/drivers/usb/host/imx21-hcd.c
@@ -824,13 +824,13 @@
i = DIV_ROUND_UP(wrap_frame(
cur_frame - urb->start_frame),
urb->interval);
- if (urb->transfer_flags & URB_ISO_ASAP) {
+
+ /* Treat underruns as if URB_ISO_ASAP was set */
+ if ((urb->transfer_flags & URB_ISO_ASAP) ||
+ i >= urb->number_of_packets) {
urb->start_frame = wrap_frame(urb->start_frame
+ i * urb->interval);
i = 0;
- } else if (i >= urb->number_of_packets) {
- ret = -EXDEV;
- goto alloc_dmem_failed;
}
}
}
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 8f6b695..604cad1 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -216,31 +216,26 @@
frame &= ~(ed->interval - 1);
frame |= ed->branch;
urb->start_frame = frame;
+ ed->last_iso = frame + ed->interval * (size - 1);
}
} else if (ed->type == PIPE_ISOCHRONOUS) {
u16 next = ohci_frame_no(ohci) + 1;
u16 frame = ed->last_iso + ed->interval;
+ u16 length = ed->interval * (size - 1);
/* Behind the scheduling threshold? */
if (unlikely(tick_before(frame, next))) {
- /* USB_ISO_ASAP: Round up to the first available slot */
+ /* URB_ISO_ASAP: Round up to the first available slot */
if (urb->transfer_flags & URB_ISO_ASAP) {
frame += (next - frame + ed->interval - 1) &
-ed->interval;
/*
- * Not ASAP: Use the next slot in the stream. If
- * the entire URB falls before the threshold, fail.
+ * Not ASAP: Use the next slot in the stream,
+ * no matter what.
*/
} else {
- if (tick_before(frame + ed->interval *
- (urb->number_of_packets - 1), next)) {
- retval = -EXDEV;
- usb_hcd_unlink_urb_from_ep(hcd, urb);
- goto fail;
- }
-
/*
* Some OHCI hardware doesn't handle late TDs
* correctly. After retiring them it proceeds
@@ -251,9 +246,16 @@
urb_priv->td_cnt = DIV_ROUND_UP(
(u16) (next - frame),
ed->interval);
+ if (urb_priv->td_cnt >= urb_priv->length) {
+ ++urb_priv->td_cnt; /* Mark it */
+ ohci_dbg(ohci, "iso underrun %p (%u+%u < %u)\n",
+ urb, frame, length,
+ next);
+ }
}
}
urb->start_frame = frame;
+ ed->last_iso = frame + length;
}
/* fill the TDs and link them to the ed; and
diff --git a/drivers/usb/host/ohci-q.c b/drivers/usb/host/ohci-q.c
index df4a670..e7f577e 100644
--- a/drivers/usb/host/ohci-q.c
+++ b/drivers/usb/host/ohci-q.c
@@ -41,9 +41,13 @@
__releases(ohci->lock)
__acquires(ohci->lock)
{
- struct device *dev = ohci_to_hcd(ohci)->self.controller;
+ struct device *dev = ohci_to_hcd(ohci)->self.controller;
+ struct usb_host_endpoint *ep = urb->ep;
+ struct urb_priv *urb_priv;
+
// ASSERT (urb->hcpriv != 0);
+ restart:
urb_free_priv (ohci, urb->hcpriv);
urb->hcpriv = NULL;
if (likely(status == -EINPROGRESS))
@@ -80,6 +84,21 @@
ohci->hc_control &= ~(OHCI_CTRL_PLE|OHCI_CTRL_IE);
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
}
+
+ /*
+ * An isochronous URB that is sumitted too late won't have any TDs
+ * (marked by the fact that the td_cnt value is larger than the
+ * actual number of TDs). If the next URB on this endpoint is like
+ * that, give it back now.
+ */
+ if (!list_empty(&ep->urb_list)) {
+ urb = list_first_entry(&ep->urb_list, struct urb, urb_list);
+ urb_priv = urb->hcpriv;
+ if (urb_priv->td_cnt > urb_priv->length) {
+ status = 0;
+ goto restart;
+ }
+ }
}
@@ -546,7 +565,6 @@
td->hwCBP = cpu_to_hc32 (ohci, data & 0xFFFFF000);
*ohci_hwPSWp(ohci, td, 0) = cpu_to_hc16 (ohci,
(data & 0x0FFF) | 0xE000);
- td->ed->last_iso = info & 0xffff;
} else {
td->hwCBP = cpu_to_hc32 (ohci, data);
}
@@ -996,7 +1014,7 @@
urb_priv->td_cnt++;
/* if URB is done, clean up */
- if (urb_priv->td_cnt == urb_priv->length) {
+ if (urb_priv->td_cnt >= urb_priv->length) {
modified = completed = 1;
finish_urb(ohci, urb, 0);
}
@@ -1086,7 +1104,7 @@
urb_priv->td_cnt++;
/* If all this urb's TDs are done, call complete() */
- if (urb_priv->td_cnt == urb_priv->length)
+ if (urb_priv->td_cnt >= urb_priv->length)
finish_urb(ohci, urb, status);
/* clean schedule: unlink EDs that are no longer busy */
diff --git a/drivers/usb/host/uhci-pci.c b/drivers/usb/host/uhci-pci.c
index c300bd2f7..0f228c4 100644
--- a/drivers/usb/host/uhci-pci.c
+++ b/drivers/usb/host/uhci-pci.c
@@ -293,7 +293,7 @@
.remove = usb_hcd_pci_remove,
.shutdown = uhci_shutdown,
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
.driver = {
.pm = &usb_hcd_pci_pm_ops
},
diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index 041c6dd..da6f56d 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -1303,7 +1303,7 @@
}
/* Fell behind? */
- if (uhci_frame_before_eq(frame, next)) {
+ if (!uhci_frame_before_eq(next, frame)) {
/* USB_ISO_ASAP: Round up to the first available slot */
if (urb->transfer_flags & URB_ISO_ASAP)
@@ -1311,13 +1311,17 @@
-qh->period;
/*
- * Not ASAP: Use the next slot in the stream. If
- * the entire URB falls before the threshold, fail.
+ * Not ASAP: Use the next slot in the stream,
+ * no matter what.
*/
else if (!uhci_frame_before_eq(next,
frame + (urb->number_of_packets - 1) *
qh->period))
- return -EXDEV;
+ dev_dbg(uhci_dev(uhci), "iso underrun %p (%u+%u < %u)\n",
+ urb, frame,
+ (urb->number_of_packets - 1) *
+ qh->period,
+ next);
}
}
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index fae697e..773a6b2 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -287,7 +287,7 @@
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
xhci_queue_stop_endpoint(xhci, slot_id, i, suspend);
}
- cmd->command_trb = xhci->cmd_ring->enqueue;
+ cmd->command_trb = xhci_find_next_enqueue(xhci->cmd_ring);
list_add_tail(&cmd->cmd_list, &virt_dev->cmd_list);
xhci_queue_stop_endpoint(xhci, slot_id, 0, suspend);
xhci_ring_cmd_db(xhci);
@@ -552,11 +552,15 @@
* - Mark a port as being done with device resume,
* and ring the endpoint doorbells.
* - Stop the Synopsys redriver Compliance Mode polling.
+ * - Drop and reacquire the xHCI lock, in order to wait for port resume.
*/
static u32 xhci_get_port_status(struct usb_hcd *hcd,
struct xhci_bus_state *bus_state,
__le32 __iomem **port_array,
- u16 wIndex, u32 raw_port_status)
+ u16 wIndex, u32 raw_port_status,
+ unsigned long flags)
+ __releases(&xhci->lock)
+ __acquires(&xhci->lock)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
u32 status = 0;
@@ -591,21 +595,42 @@
return 0xffffffff;
if (time_after_eq(jiffies,
bus_state->resume_done[wIndex])) {
+ int time_left;
+
xhci_dbg(xhci, "Resume USB2 port %d\n",
wIndex + 1);
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
+
+ set_bit(wIndex, &bus_state->rexit_ports);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
- xhci_dbg(xhci, "set port %d resume\n",
- wIndex + 1);
- slot_id = xhci_find_slot_id_by_port(hcd, xhci,
- wIndex + 1);
- if (!slot_id) {
- xhci_dbg(xhci, "slot_id is zero\n");
- return 0xffffffff;
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ time_left = wait_for_completion_timeout(
+ &bus_state->rexit_done[wIndex],
+ msecs_to_jiffies(
+ XHCI_MAX_REXIT_TIMEOUT));
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ if (time_left) {
+ slot_id = xhci_find_slot_id_by_port(hcd,
+ xhci, wIndex + 1);
+ if (!slot_id) {
+ xhci_dbg(xhci, "slot_id is zero\n");
+ return 0xffffffff;
+ }
+ xhci_ring_device(xhci, slot_id);
+ } else {
+ int port_status = xhci_readl(xhci,
+ port_array[wIndex]);
+ xhci_warn(xhci, "Port resume took longer than %i msec, port status = 0x%x\n",
+ XHCI_MAX_REXIT_TIMEOUT,
+ port_status);
+ status |= USB_PORT_STAT_SUSPEND;
+ clear_bit(wIndex, &bus_state->rexit_ports);
}
- xhci_ring_device(xhci, slot_id);
+
bus_state->port_c_suspend |= 1 << wIndex;
bus_state->suspended_ports &= ~(1 << wIndex);
} else {
@@ -728,7 +753,7 @@
break;
}
status = xhci_get_port_status(hcd, bus_state, port_array,
- wIndex, temp);
+ wIndex, temp, flags);
if (status == 0xffffffff)
goto error;
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 53b972c..83bcd13 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -2428,6 +2428,8 @@
for (i = 0; i < USB_MAXCHILDREN; ++i) {
xhci->bus_state[0].resume_done[i] = 0;
xhci->bus_state[1].resume_done[i] = 0;
+ /* Only the USB 2.0 completions will ever be used. */
+ init_completion(&xhci->bus_state[1].rexit_done[i]);
}
if (scratchpad_alloc(xhci, flags))
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index c2d4950..236c3aa 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -351,7 +351,7 @@
/* suspend and resume implemented later */
.shutdown = usb_hcd_pci_shutdown,
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
.driver = {
.pm = &usb_hcd_pci_pm_ops
},
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 411da1f..6bfbd80 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -123,6 +123,16 @@
return TRB_TYPE_LINK_LE32(link->control);
}
+union xhci_trb *xhci_find_next_enqueue(struct xhci_ring *ring)
+{
+ /* Enqueue pointer can be left pointing to the link TRB,
+ * we must handle that
+ */
+ if (TRB_TYPE_LINK_LE32(ring->enqueue->link.control))
+ return ring->enq_seg->next->trbs;
+ return ring->enqueue;
+}
+
/* Updates trb to point to the next TRB in the ring, and updates seg if the next
* TRB is in a new segment. This does not skip over link TRBs, and it does not
* effect the ring dequeue or enqueue pointers.
@@ -859,8 +869,12 @@
/* Otherwise ring the doorbell(s) to restart queued transfers */
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
}
- ep->stopped_td = NULL;
- ep->stopped_trb = NULL;
+
+ /* Clear stopped_td and stopped_trb if endpoint is not halted */
+ if (!(ep->ep_state & EP_HALTED)) {
+ ep->stopped_td = NULL;
+ ep->stopped_trb = NULL;
+ }
/*
* Drop the lock and complete the URBs in the cancelled TD list.
@@ -1414,6 +1428,12 @@
inc_deq(xhci, xhci->cmd_ring);
return;
}
+ /* There is no command to handle if we get a stop event when the
+ * command ring is empty, event->cmd_trb points to the next
+ * unset command
+ */
+ if (xhci->cmd_ring->dequeue == xhci->cmd_ring->enqueue)
+ return;
}
switch (le32_to_cpu(xhci->cmd_ring->dequeue->generic.field[3])
@@ -1743,6 +1763,19 @@
}
}
+ /*
+ * Check to see if xhci-hub.c is waiting on RExit to U0 transition (or
+ * RExit to a disconnect state). If so, let the the driver know it's
+ * out of the RExit state.
+ */
+ if (!DEV_SUPERSPEED(temp) &&
+ test_and_clear_bit(faked_port_index,
+ &bus_state->rexit_ports)) {
+ complete(&bus_state->rexit_done[faked_port_index]);
+ bogus_port_status = true;
+ goto cleanup;
+ }
+
if (hcd->speed != HCD_USB3)
xhci_test_and_clear_bit(xhci, port_array, faked_port_index,
PORT_PLC);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 49b6edb..1e36dbb 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -2598,15 +2598,7 @@
if (command) {
cmd_completion = command->completion;
cmd_status = &command->status;
- command->command_trb = xhci->cmd_ring->enqueue;
-
- /* Enqueue pointer can be left pointing to the link TRB,
- * we must handle that
- */
- if (TRB_TYPE_LINK_LE32(command->command_trb->link.control))
- command->command_trb =
- xhci->cmd_ring->enq_seg->next->trbs;
-
+ command->command_trb = xhci_find_next_enqueue(xhci->cmd_ring);
list_add_tail(&command->cmd_list, &virt_dev->cmd_list);
} else {
cmd_completion = &virt_dev->cmd_completion;
@@ -2614,7 +2606,7 @@
}
init_completion(cmd_completion);
- cmd_trb = xhci->cmd_ring->dequeue;
+ cmd_trb = xhci_find_next_enqueue(xhci->cmd_ring);
if (!ctx_change)
ret = xhci_queue_configure_endpoint(xhci, in_ctx->dma,
udev->slot_id, must_succeed);
@@ -3439,14 +3431,7 @@
/* Attempt to submit the Reset Device command to the command ring */
spin_lock_irqsave(&xhci->lock, flags);
- reset_device_cmd->command_trb = xhci->cmd_ring->enqueue;
-
- /* Enqueue pointer can be left pointing to the link TRB,
- * we must handle that
- */
- if (TRB_TYPE_LINK_LE32(reset_device_cmd->command_trb->link.control))
- reset_device_cmd->command_trb =
- xhci->cmd_ring->enq_seg->next->trbs;
+ reset_device_cmd->command_trb = xhci_find_next_enqueue(xhci->cmd_ring);
list_add_tail(&reset_device_cmd->cmd_list, &virt_dev->cmd_list);
ret = xhci_queue_reset_device(xhci, slot_id);
@@ -3650,7 +3635,7 @@
union xhci_trb *cmd_trb;
spin_lock_irqsave(&xhci->lock, flags);
- cmd_trb = xhci->cmd_ring->dequeue;
+ cmd_trb = xhci_find_next_enqueue(xhci->cmd_ring);
ret = xhci_queue_slot_control(xhci, TRB_ENABLE_SLOT, 0);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
@@ -3785,7 +3770,7 @@
slot_ctx->dev_info >> 27);
spin_lock_irqsave(&xhci->lock, flags);
- cmd_trb = xhci->cmd_ring->dequeue;
+ cmd_trb = xhci_find_next_enqueue(xhci->cmd_ring);
ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma,
udev->slot_id);
if (ret) {
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 46aa148..289fbfb 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1412,8 +1412,18 @@
unsigned long resume_done[USB_MAXCHILDREN];
/* which ports have started to resume */
unsigned long resuming_ports;
+ /* Which ports are waiting on RExit to U0 transition. */
+ unsigned long rexit_ports;
+ struct completion rexit_done[USB_MAXCHILDREN];
};
+
+/*
+ * It can take up to 20 ms to transition from RExit to U0 on the
+ * Intel Lynx Point LP xHCI host.
+ */
+#define XHCI_MAX_REXIT_TIMEOUT (20 * 1000)
+
static inline unsigned int hcd_index(struct usb_hcd *hcd)
{
if (hcd->speed == HCD_USB3)
@@ -1840,6 +1850,7 @@
union xhci_trb *cmd_trb);
void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int slot_id,
unsigned int ep_index, unsigned int stream_id);
+union xhci_trb *xhci_find_next_enqueue(struct xhci_ring *ring);
/* xHCI roothub code */
void xhci_set_link_state(struct xhci_hcd *xhci, __le32 __iomem **port_array,
