| ThinkPad ACPI Extras Driver |
| |
| Version 0.22 |
| November 23rd, 2008 |
| |
| Borislav Deianov <borislav@users.sf.net> |
| Henrique de Moraes Holschuh <hmh@hmh.eng.br> |
| http://ibm-acpi.sf.net/ |
| |
| |
| This is a Linux driver for the IBM and Lenovo ThinkPad laptops. It |
| supports various features of these laptops which are accessible |
| through the ACPI and ACPI EC framework, but not otherwise fully |
| supported by the generic Linux ACPI drivers. |
| |
| This driver used to be named ibm-acpi until kernel 2.6.21 and release |
| 0.13-20070314. It used to be in the drivers/acpi tree, but it was |
| moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel |
| 2.6.22, and release 0.14. It was moved to drivers/platform/x86 for |
| kernel 2.6.29 and release 0.22. |
| |
| The driver is named "thinkpad-acpi". In some places, like module |
| names and log messages, "thinkpad_acpi" is used because of userspace |
| issues. |
| |
| "tpacpi" is used as a shorthand where "thinkpad-acpi" would be too |
| long due to length limitations on some Linux kernel versions. |
| |
| Status |
| ------ |
| |
| The features currently supported are the following (see below for |
| detailed description): |
| |
| - Fn key combinations |
| - Bluetooth enable and disable |
| - video output switching, expansion control |
| - ThinkLight on and off |
| - limited docking and undocking |
| - UltraBay eject |
| - CMOS/UCMS control |
| - LED control |
| - ACPI sounds |
| - temperature sensors |
| - Experimental: embedded controller register dump |
| - LCD brightness control |
| - Volume control |
| - Fan control and monitoring: fan speed, fan enable/disable |
| - WAN enable and disable |
| - UWB enable and disable |
| |
| A compatibility table by model and feature is maintained on the web |
| site, http://ibm-acpi.sf.net/. I appreciate any success or failure |
| reports, especially if they add to or correct the compatibility table. |
| Please include the following information in your report: |
| |
| - ThinkPad model name |
| - a copy of your ACPI tables, using the "acpidump" utility |
| - a copy of the output of dmidecode, with serial numbers |
| and UUIDs masked off |
| - which driver features work and which don't |
| - the observed behavior of non-working features |
| |
| Any other comments or patches are also more than welcome. |
| |
| |
| Installation |
| ------------ |
| |
| If you are compiling this driver as included in the Linux kernel |
| sources, look for the CONFIG_THINKPAD_ACPI Kconfig option. |
| It is located on the menu path: "Device Drivers" -> "X86 Platform |
| Specific Device Drivers" -> "ThinkPad ACPI Laptop Extras". |
| |
| |
| Features |
| -------- |
| |
| The driver exports two different interfaces to userspace, which can be |
| used to access the features it provides. One is a legacy procfs-based |
| interface, which will be removed at some time in the future. The other |
| is a new sysfs-based interface which is not complete yet. |
| |
| The procfs interface creates the /proc/acpi/ibm directory. There is a |
| file under that directory for each feature it supports. The procfs |
| interface is mostly frozen, and will change very little if at all: it |
| will not be extended to add any new functionality in the driver, instead |
| all new functionality will be implemented on the sysfs interface. |
| |
| The sysfs interface tries to blend in the generic Linux sysfs subsystems |
| and classes as much as possible. Since some of these subsystems are not |
| yet ready or stabilized, it is expected that this interface will change, |
| and any and all userspace programs must deal with it. |
| |
| |
| Notes about the sysfs interface: |
| |
| Unlike what was done with the procfs interface, correctness when talking |
| to the sysfs interfaces will be enforced, as will correctness in the |
| thinkpad-acpi's implementation of sysfs interfaces. |
| |
| Also, any bugs in the thinkpad-acpi sysfs driver code or in the |
| thinkpad-acpi's implementation of the sysfs interfaces will be fixed for |
| maximum correctness, even if that means changing an interface in |
| non-compatible ways. As these interfaces mature both in the kernel and |
| in thinkpad-acpi, such changes should become quite rare. |
| |
| Applications interfacing to the thinkpad-acpi sysfs interfaces must |
| follow all sysfs guidelines and correctly process all errors (the sysfs |
| interface makes extensive use of errors). File descriptors and open / |
| close operations to the sysfs inodes must also be properly implemented. |
| |
| The version of thinkpad-acpi's sysfs interface is exported by the driver |
| as a driver attribute (see below). |
| |
| Sysfs driver attributes are on the driver's sysfs attribute space, |
| for 2.6.23+ this is /sys/bus/platform/drivers/thinkpad_acpi/ and |
| /sys/bus/platform/drivers/thinkpad_hwmon/ |
| |
| Sysfs device attributes are on the thinkpad_acpi device sysfs attribute |
| space, for 2.6.23+ this is /sys/devices/platform/thinkpad_acpi/. |
| |
| Sysfs device attributes for the sensors and fan are on the |
| thinkpad_hwmon device's sysfs attribute space, but you should locate it |
| looking for a hwmon device with the name attribute of "thinkpad", or |
| better yet, through libsensors. |
| |
| |
| Driver version |
| -------------- |
| |
| procfs: /proc/acpi/ibm/driver |
| sysfs driver attribute: version |
| |
| The driver name and version. No commands can be written to this file. |
| |
| |
| Sysfs interface version |
| ----------------------- |
| |
| sysfs driver attribute: interface_version |
| |
| Version of the thinkpad-acpi sysfs interface, as an unsigned long |
| (output in hex format: 0xAAAABBCC), where: |
| AAAA - major revision |
| BB - minor revision |
| CC - bugfix revision |
| |
| The sysfs interface version changelog for the driver can be found at the |
| end of this document. Changes to the sysfs interface done by the kernel |
| subsystems are not documented here, nor are they tracked by this |
| attribute. |
| |
| Changes to the thinkpad-acpi sysfs interface are only considered |
| non-experimental when they are submitted to Linux mainline, at which |
| point the changes in this interface are documented and interface_version |
| may be updated. If you are using any thinkpad-acpi features not yet |
| sent to mainline for merging, you do so on your own risk: these features |
| may disappear, or be implemented in a different and incompatible way by |
| the time they are merged in Linux mainline. |
| |
| Changes that are backwards-compatible by nature (e.g. the addition of |
| attributes that do not change the way the other attributes work) do not |
| always warrant an update of interface_version. Therefore, one must |
| expect that an attribute might not be there, and deal with it properly |
| (an attribute not being there *is* a valid way to make it clear that a |
| feature is not available in sysfs). |
| |
| |
| Hot keys |
| -------- |
| |
| procfs: /proc/acpi/ibm/hotkey |
| sysfs device attribute: hotkey_* |
| |
| In a ThinkPad, the ACPI HKEY handler is responsible for communicating |
| some important events and also keyboard hot key presses to the operating |
| system. Enabling the hotkey functionality of thinkpad-acpi signals the |
| firmware that such a driver is present, and modifies how the ThinkPad |
| firmware will behave in many situations. |
| |
| The driver enables the HKEY ("hot key") event reporting automatically |
| when loaded, and disables it when it is removed. |
| |
| The driver will report HKEY events in the following format: |
| |
| ibm/hotkey HKEY 00000080 0000xxxx |
| |
| Some of these events refer to hot key presses, but not all of them. |
| |
| The driver will generate events over the input layer for hot keys and |
| radio switches, and over the ACPI netlink layer for other events. The |
| input layer support accepts the standard IOCTLs to remap the keycodes |
| assigned to each hot key. |
| |
| The hot key bit mask allows some control over which hot keys generate |
| events. If a key is "masked" (bit set to 0 in the mask), the firmware |
| will handle it. If it is "unmasked", it signals the firmware that |
| thinkpad-acpi would prefer to handle it, if the firmware would be so |
| kind to allow it (and it often doesn't!). |
| |
| Not all bits in the mask can be modified. Not all bits that can be |
| modified do anything. Not all hot keys can be individually controlled |
| by the mask. Some models do not support the mask at all, and in those |
| models, hot keys cannot be controlled individually. The behaviour of |
| the mask is, therefore, highly dependent on the ThinkPad model. |
| |
| Note that unmasking some keys prevents their default behavior. For |
| example, if Fn+F5 is unmasked, that key will no longer enable/disable |
| Bluetooth by itself. |
| |
| Note also that not all Fn key combinations are supported through ACPI. |
| For example, on the X40, the brightness, volume and "Access IBM" buttons |
| do not generate ACPI events even with this driver. They *can* be used |
| through the "ThinkPad Buttons" utility, see http://www.nongnu.org/tpb/ |
| |
| procfs notes: |
| |
| The following commands can be written to the /proc/acpi/ibm/hotkey file: |
| |
| echo 0xffffffff > /proc/acpi/ibm/hotkey -- enable all hot keys |
| echo 0 > /proc/acpi/ibm/hotkey -- disable all possible hot keys |
| ... any other 8-hex-digit mask ... |
| echo reset > /proc/acpi/ibm/hotkey -- restore the original mask |
| |
| The following commands have been deprecated and will cause the kernel |
| to log a warning: |
| |
| echo enable > /proc/acpi/ibm/hotkey -- does nothing |
| echo disable > /proc/acpi/ibm/hotkey -- returns an error |
| |
| The procfs interface does not support NVRAM polling control. So as to |
| maintain maximum bug-to-bug compatibility, it does not report any masks, |
| nor does it allow one to manipulate the hot key mask when the firmware |
| does not support masks at all, even if NVRAM polling is in use. |
| |
| sysfs notes: |
| |
| hotkey_bios_enabled: |
| DEPRECATED, WILL BE REMOVED SOON. |
| |
| Returns 0. |
| |
| hotkey_bios_mask: |
| Returns the hot keys mask when thinkpad-acpi was loaded. |
| Upon module unload, the hot keys mask will be restored |
| to this value. |
| |
| hotkey_enable: |
| DEPRECATED, WILL BE REMOVED SOON. |
| |
| 0: returns -EPERM |
| 1: does nothing |
| |
| hotkey_mask: |
| bit mask to enable driver-handling (and depending on |
| the firmware, ACPI event generation) for each hot key |
| (see above). Returns the current status of the hot keys |
| mask, and allows one to modify it. |
| |
| Note: when NVRAM polling is active, the firmware mask |
| will be different from the value returned by |
| hotkey_mask. The driver will retain enabled bits for |
| hotkeys that are under NVRAM polling even if the |
| firmware refuses them, and will not set these bits on |
| the firmware hot key mask. |
| |
| hotkey_all_mask: |
| bit mask that should enable event reporting for all |
| supported hot keys, when echoed to hotkey_mask above. |
| Unless you know which events need to be handled |
| passively (because the firmware *will* handle them |
| anyway), do *not* use hotkey_all_mask. Use |
| hotkey_recommended_mask, instead. You have been warned. |
| |
| hotkey_recommended_mask: |
| bit mask that should enable event reporting for all |
| supported hot keys, except those which are always |
| handled by the firmware anyway. Echo it to |
| hotkey_mask above, to use. |
| |
| hotkey_source_mask: |
| bit mask that selects which hot keys will the driver |
| poll the NVRAM for. This is auto-detected by the driver |
| based on the capabilities reported by the ACPI firmware, |
| but it can be overridden at runtime. |
| |
| Hot keys whose bits are set in both hotkey_source_mask |
| and also on hotkey_mask are polled for in NVRAM. Only a |
| few hot keys are available through CMOS NVRAM polling. |
| |
| Warning: when in NVRAM mode, the volume up/down/mute |
| keys are synthesized according to changes in the mixer, |
| so you have to use volume up or volume down to unmute, |
| as per the ThinkPad volume mixer user interface. When |
| in ACPI event mode, volume up/down/mute are reported as |
| separate events, but this behaviour may be corrected in |
| future releases of this driver, in which case the |
| ThinkPad volume mixer user interface semantics will be |
| enforced. |
| |
| hotkey_poll_freq: |
| frequency in Hz for hot key polling. It must be between |
| 0 and 25 Hz. Polling is only carried out when strictly |
| needed. |
| |
| Setting hotkey_poll_freq to zero disables polling, and |
| will cause hot key presses that require NVRAM polling |
| to never be reported. |
| |
| Setting hotkey_poll_freq too low will cause repeated |
| pressings of the same hot key to be misreported as a |
| single key press, or to not even be detected at all. |
| The recommended polling frequency is 10Hz. |
| |
| hotkey_radio_sw: |
| If the ThinkPad has a hardware radio switch, this |
| attribute will read 0 if the switch is in the "radios |
| disabled" position, and 1 if the switch is in the |
| "radios enabled" position. |
| |
| This attribute has poll()/select() support. |
| |
| hotkey_tablet_mode: |
| If the ThinkPad has tablet capabilities, this attribute |
| will read 0 if the ThinkPad is in normal mode, and |
| 1 if the ThinkPad is in tablet mode. |
| |
| This attribute has poll()/select() support. |
| |
| hotkey_report_mode: |
| Returns the state of the procfs ACPI event report mode |
| filter for hot keys. If it is set to 1 (the default), |
| all hot key presses are reported both through the input |
| layer and also as ACPI events through procfs (but not |
| through netlink). If it is set to 2, hot key presses |
| are reported only through the input layer. |
| |
| This attribute is read-only in kernels 2.6.23 or later, |
| and read-write on earlier kernels. |
| |
| May return -EPERM (write access locked out by module |
| parameter) or -EACCES (read-only). |
| |
| wakeup_reason: |
| Set to 1 if the system is waking up because the user |
| requested a bay ejection. Set to 2 if the system is |
| waking up because the user requested the system to |
| undock. Set to zero for normal wake-ups or wake-ups |
| due to unknown reasons. |
| |
| This attribute has poll()/select() support. |
| |
| wakeup_hotunplug_complete: |
| Set to 1 if the system was waken up because of an |
| undock or bay ejection request, and that request |
| was successfully completed. At this point, it might |
| be useful to send the system back to sleep, at the |
| user's choice. Refer to HKEY events 0x4003 and |
| 0x3003, below. |
| |
| This attribute has poll()/select() support. |
| |
| input layer notes: |
| |
| A Hot key is mapped to a single input layer EV_KEY event, possibly |
| followed by an EV_MSC MSC_SCAN event that shall contain that key's scan |
| code. An EV_SYN event will always be generated to mark the end of the |
| event block. |
| |
| Do not use the EV_MSC MSC_SCAN events to process keys. They are to be |
| used as a helper to remap keys, only. They are particularly useful when |
| remapping KEY_UNKNOWN keys. |
| |
| The events are available in an input device, with the following id: |
| |
| Bus: BUS_HOST |
| vendor: 0x1014 (PCI_VENDOR_ID_IBM) or |
| 0x17aa (PCI_VENDOR_ID_LENOVO) |
| product: 0x5054 ("TP") |
| version: 0x4101 |
| |
| The version will have its LSB incremented if the keymap changes in a |
| backwards-compatible way. The MSB shall always be 0x41 for this input |
| device. If the MSB is not 0x41, do not use the device as described in |
| this section, as it is either something else (e.g. another input device |
| exported by a thinkpad driver, such as HDAPS) or its functionality has |
| been changed in a non-backwards compatible way. |
| |
| Adding other event types for other functionalities shall be considered a |
| backwards-compatible change for this input device. |
| |
| Thinkpad-acpi Hot Key event map (version 0x4101): |
| |
| ACPI Scan |
| event code Key Notes |
| |
| 0x1001 0x00 FN+F1 - |
| 0x1002 0x01 FN+F2 IBM: battery (rare) |
| Lenovo: Screen lock |
| |
| 0x1003 0x02 FN+F3 Many IBM models always report |
| this hot key, even with hot keys |
| disabled or with Fn+F3 masked |
| off |
| IBM: screen lock |
| Lenovo: battery |
| |
| 0x1004 0x03 FN+F4 Sleep button (ACPI sleep button |
| semantics, i.e. sleep-to-RAM). |
| It is always generate some kind |
| of event, either the hot key |
| event or a ACPI sleep button |
| event. The firmware may |
| refuse to generate further FN+F4 |
| key presses until a S3 or S4 ACPI |
| sleep cycle is performed or some |
| time passes. |
| |
| 0x1005 0x04 FN+F5 Radio. Enables/disables |
| the internal Bluetooth hardware |
| and W-WAN card if left in control |
| of the firmware. Does not affect |
| the WLAN card. |
| Should be used to turn on/off all |
| radios (Bluetooth+W-WAN+WLAN), |
| really. |
| |
| 0x1006 0x05 FN+F6 - |
| |
| 0x1007 0x06 FN+F7 Video output cycle. |
| Do you feel lucky today? |
| |
| 0x1008 0x07 FN+F8 IBM: toggle screen expand |
| Lenovo: configure UltraNav |
| |
| 0x1009 0x08 FN+F9 - |
| .. .. .. |
| 0x100B 0x0A FN+F11 - |
| |
| 0x100C 0x0B FN+F12 Sleep to disk. You are always |
| supposed to handle it yourself, |
| either through the ACPI event, |
| or through a hotkey event. |
| The firmware may refuse to |
| generate further FN+F4 key |
| press events until a S3 or S4 |
| ACPI sleep cycle is performed, |
| or some time passes. |
| |
| 0x100D 0x0C FN+BACKSPACE - |
| 0x100E 0x0D FN+INSERT - |
| 0x100F 0x0E FN+DELETE - |
| |
| 0x1010 0x0F FN+HOME Brightness up. This key is |
| always handled by the firmware |
| in IBM ThinkPads, even when |
| unmasked. Just leave it alone. |
| For Lenovo ThinkPads with a new |
| BIOS, it has to be handled either |
| by the ACPI OSI, or by userspace. |
| 0x1011 0x10 FN+END Brightness down. See brightness |
| up for details. |
| |
| 0x1012 0x11 FN+PGUP ThinkLight toggle. This key is |
| always handled by the firmware, |
| even when unmasked. |
| |
| 0x1013 0x12 FN+PGDOWN - |
| |
| 0x1014 0x13 FN+SPACE Zoom key |
| |
| 0x1015 0x14 VOLUME UP Internal mixer volume up. This |
| key is always handled by the |
| firmware, even when unmasked. |
| NOTE: Lenovo seems to be changing |
| this. |
| 0x1016 0x15 VOLUME DOWN Internal mixer volume up. This |
| key is always handled by the |
| firmware, even when unmasked. |
| NOTE: Lenovo seems to be changing |
| this. |
| 0x1017 0x16 MUTE Mute internal mixer. This |
| key is always handled by the |
| firmware, even when unmasked. |
| |
| 0x1018 0x17 THINKPAD ThinkPad/Access IBM/Lenovo key |
| |
| 0x1019 0x18 unknown |
| .. .. .. |
| 0x1020 0x1F unknown |
| |
| The ThinkPad firmware does not allow one to differentiate when most hot |
| keys are pressed or released (either that, or we don't know how to, yet). |
| For these keys, the driver generates a set of events for a key press and |
| immediately issues the same set of events for a key release. It is |
| unknown by the driver if the ThinkPad firmware triggered these events on |
| hot key press or release, but the firmware will do it for either one, not |
| both. |
| |
| If a key is mapped to KEY_RESERVED, it generates no input events at all. |
| If a key is mapped to KEY_UNKNOWN, it generates an input event that |
| includes an scan code. If a key is mapped to anything else, it will |
| generate input device EV_KEY events. |
| |
| In addition to the EV_KEY events, thinkpad-acpi may also issue EV_SW |
| events for switches: |
| |
| SW_RFKILL_ALL T60 and later hardare rfkill rocker switch |
| SW_TABLET_MODE Tablet ThinkPads HKEY events 0x5009 and 0x500A |
| |
| Non hot-key ACPI HKEY event map: |
| 0x5001 Lid closed |
| 0x5002 Lid opened |
| 0x5009 Tablet swivel: switched to tablet mode |
| 0x500A Tablet swivel: switched to normal mode |
| 0x7000 Radio Switch may have changed state |
| |
| The above events are not propagated by the driver, except for legacy |
| compatibility purposes when hotkey_report_mode is set to 1. |
| |
| 0x2304 System is waking up from suspend to undock |
| 0x2305 System is waking up from suspend to eject bay |
| 0x2404 System is waking up from hibernation to undock |
| 0x2405 System is waking up from hibernation to eject bay |
| |
| The above events are never propagated by the driver. |
| |
| 0x3003 Bay ejection (see 0x2x05) complete, can sleep again |
| 0x4003 Undocked (see 0x2x04), can sleep again |
| 0x500B Tablet pen inserted into its storage bay |
| 0x500C Tablet pen removed from its storage bay |
| 0x5010 Brightness level changed (newer Lenovo BIOSes) |
| |
| The above events are propagated by the driver. |
| |
| Compatibility notes: |
| |
| ibm-acpi and thinkpad-acpi 0.15 (mainline kernels before 2.6.23) never |
| supported the input layer, and sent events over the procfs ACPI event |
| interface. |
| |
| To avoid sending duplicate events over the input layer and the ACPI |
| event interface, thinkpad-acpi 0.16 implements a module parameter |
| (hotkey_report_mode), and also a sysfs device attribute with the same |
| name. |
| |
| Make no mistake here: userspace is expected to switch to using the input |
| layer interface of thinkpad-acpi, together with the ACPI netlink event |
| interface in kernels 2.6.23 and later, or with the ACPI procfs event |
| interface in kernels 2.6.22 and earlier. |
| |
| If no hotkey_report_mode module parameter is specified (or it is set to |
| zero), the driver defaults to mode 1 (see below), and on kernels 2.6.22 |
| and earlier, also allows one to change the hotkey_report_mode through |
| sysfs. In kernels 2.6.23 and later, where the netlink ACPI event |
| interface is available, hotkey_report_mode cannot be changed through |
| sysfs (it is read-only). |
| |
| If the hotkey_report_mode module parameter is set to 1 or 2, it cannot |
| be changed later through sysfs (any writes will return -EPERM to signal |
| that hotkey_report_mode was locked. On 2.6.23 and later, where |
| hotkey_report_mode cannot be changed at all, writes will return -EACCES). |
| |
| hotkey_report_mode set to 1 makes the driver export through the procfs |
| ACPI event interface all hot key presses (which are *also* sent to the |
| input layer). This is a legacy compatibility behaviour, and it is also |
| the default mode of operation for the driver. |
| |
| hotkey_report_mode set to 2 makes the driver filter out the hot key |
| presses from the procfs ACPI event interface, so these events will only |
| be sent through the input layer. Userspace that has been updated to use |
| the thinkpad-acpi input layer interface should set hotkey_report_mode to |
| 2. |
| |
| Hot key press events are never sent to the ACPI netlink event interface. |
| Really up-to-date userspace under kernel 2.6.23 and later is to use the |
| netlink interface and the input layer interface, and don't bother at all |
| with hotkey_report_mode. |
| |
| |
| Brightness hotkey notes: |
| |
| These are the current sane choices for brightness key mapping in |
| thinkpad-acpi: |
| |
| For IBM and Lenovo models *without* ACPI backlight control (the ones on |
| which thinkpad-acpi will autoload its backlight interface by default, |
| and on which ACPI video does not export a backlight interface): |
| |
| 1. Don't enable or map the brightness hotkeys in thinkpad-acpi, as |
| these older firmware versions unfortunately won't respect the hotkey |
| mask for brightness keys anyway, and always reacts to them. This |
| usually work fine, unless X.org drivers are doing something to block |
| the BIOS. In that case, use (3) below. This is the default mode of |
| operation. |
| |
| 2. Enable the hotkeys, but map them to something else that is NOT |
| KEY_BRIGHTNESS_UP/DOWN or any other keycode that would cause |
| userspace to try to change the backlight level, and use that as an |
| on-screen-display hint. |
| |
| 3. IF AND ONLY IF X.org drivers find a way to block the firmware from |
| automatically changing the brightness, enable the hotkeys and map |
| them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN, and feed that to |
| something that calls xbacklight. thinkpad-acpi will not be able to |
| change brightness in that case either, so you should disable its |
| backlight interface. |
| |
| For Lenovo models *with* ACPI backlight control: |
| |
| 1. Load up ACPI video and use that. ACPI video will report ACPI |
| events for brightness change keys. Do not mess with thinkpad-acpi |
| defaults in this case. thinkpad-acpi should not have anything to do |
| with backlight events in a scenario where ACPI video is loaded: |
| brightness hotkeys must be disabled, and the backlight interface is |
| to be kept disabled as well. This is the default mode of operation. |
| |
| 2. Do *NOT* load up ACPI video, enable the hotkeys in thinkpad-acpi, |
| and map them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN. Process |
| these keys on userspace somehow (e.g. by calling xbacklight). |
| |
| |
| Bluetooth |
| --------- |
| |
| procfs: /proc/acpi/ibm/bluetooth |
| sysfs device attribute: bluetooth_enable (deprecated) |
| sysfs rfkill class: switch "tpacpi_bluetooth_sw" |
| |
| This feature shows the presence and current state of a ThinkPad |
| Bluetooth device in the internal ThinkPad CDC slot. |
| |
| If the ThinkPad supports it, the Bluetooth state is stored in NVRAM, |
| so it is kept across reboots and power-off. |
| |
| Procfs notes: |
| |
| If Bluetooth is installed, the following commands can be used: |
| |
| echo enable > /proc/acpi/ibm/bluetooth |
| echo disable > /proc/acpi/ibm/bluetooth |
| |
| Sysfs notes: |
| |
| If the Bluetooth CDC card is installed, it can be enabled / |
| disabled through the "bluetooth_enable" thinkpad-acpi device |
| attribute, and its current status can also be queried. |
| |
| enable: |
| 0: disables Bluetooth / Bluetooth is disabled |
| 1: enables Bluetooth / Bluetooth is enabled. |
| |
| Note: this interface has been superseded by the generic rfkill |
| class. It has been deprecated, and it will be removed in year |
| 2010. |
| |
| rfkill controller switch "tpacpi_bluetooth_sw": refer to |
| Documentation/rfkill.txt for details. |
| |
| |
| Video output control -- /proc/acpi/ibm/video |
| -------------------------------------------- |
| |
| This feature allows control over the devices used for video output - |
| LCD, CRT or DVI (if available). The following commands are available: |
| |
| echo lcd_enable > /proc/acpi/ibm/video |
| echo lcd_disable > /proc/acpi/ibm/video |
| echo crt_enable > /proc/acpi/ibm/video |
| echo crt_disable > /proc/acpi/ibm/video |
| echo dvi_enable > /proc/acpi/ibm/video |
| echo dvi_disable > /proc/acpi/ibm/video |
| echo auto_enable > /proc/acpi/ibm/video |
| echo auto_disable > /proc/acpi/ibm/video |
| echo expand_toggle > /proc/acpi/ibm/video |
| echo video_switch > /proc/acpi/ibm/video |
| |
| Each video output device can be enabled or disabled individually. |
| Reading /proc/acpi/ibm/video shows the status of each device. |
| |
| Automatic video switching can be enabled or disabled. When automatic |
| video switching is enabled, certain events (e.g. opening the lid, |
| docking or undocking) cause the video output device to change |
| automatically. While this can be useful, it also causes flickering |
| and, on the X40, video corruption. By disabling automatic switching, |
| the flickering or video corruption can be avoided. |
| |
| The video_switch command cycles through the available video outputs |
| (it simulates the behavior of Fn-F7). |
| |
| Video expansion can be toggled through this feature. This controls |
| whether the display is expanded to fill the entire LCD screen when a |
| mode with less than full resolution is used. Note that the current |
| video expansion status cannot be determined through this feature. |
| |
| Note that on many models (particularly those using Radeon graphics |
| chips) the X driver configures the video card in a way which prevents |
| Fn-F7 from working. This also disables the video output switching |
| features of this driver, as it uses the same ACPI methods as |
| Fn-F7. Video switching on the console should still work. |
| |
| UPDATE: refer to https://bugs.freedesktop.org/show_bug.cgi?id=2000 |
| |
| |
| ThinkLight control |
| ------------------ |
| |
| procfs: /proc/acpi/ibm/light |
| sysfs attributes: as per LED class, for the "tpacpi::thinklight" LED |
| |
| procfs notes: |
| |
| The ThinkLight status can be read and set through the procfs interface. A |
| few models which do not make the status available will show the ThinkLight |
| status as "unknown". The available commands are: |
| |
| echo on > /proc/acpi/ibm/light |
| echo off > /proc/acpi/ibm/light |
| |
| sysfs notes: |
| |
| The ThinkLight sysfs interface is documented by the LED class |
| documentation, in Documentation/leds-class.txt. The ThinkLight LED name |
| is "tpacpi::thinklight". |
| |
| Due to limitations in the sysfs LED class, if the status of the ThinkLight |
| cannot be read or if it is unknown, thinkpad-acpi will report it as "off". |
| It is impossible to know if the status returned through sysfs is valid. |
| |
| |
| Docking / undocking -- /proc/acpi/ibm/dock |
| ------------------------------------------ |
| |
| Docking and undocking (e.g. with the X4 UltraBase) requires some |
| actions to be taken by the operating system to safely make or break |
| the electrical connections with the dock. |
| |
| The docking feature of this driver generates the following ACPI events: |
| |
| ibm/dock GDCK 00000003 00000001 -- eject request |
| ibm/dock GDCK 00000003 00000002 -- undocked |
| ibm/dock GDCK 00000000 00000003 -- docked |
| |
| NOTE: These events will only be generated if the laptop was docked |
| when originally booted. This is due to the current lack of support for |
| hot plugging of devices in the Linux ACPI framework. If the laptop was |
| booted while not in the dock, the following message is shown in the |
| logs: |
| |
| Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present |
| |
| In this case, no dock-related events are generated but the dock and |
| undock commands described below still work. They can be executed |
| manually or triggered by Fn key combinations (see the example acpid |
| configuration files included in the driver tarball package available |
| on the web site). |
| |
| When the eject request button on the dock is pressed, the first event |
| above is generated. The handler for this event should issue the |
| following command: |
| |
| echo undock > /proc/acpi/ibm/dock |
| |
| After the LED on the dock goes off, it is safe to eject the laptop. |
| Note: if you pressed this key by mistake, go ahead and eject the |
| laptop, then dock it back in. Otherwise, the dock may not function as |
| expected. |
| |
| When the laptop is docked, the third event above is generated. The |
| handler for this event should issue the following command to fully |
| enable the dock: |
| |
| echo dock > /proc/acpi/ibm/dock |
| |
| The contents of the /proc/acpi/ibm/dock file shows the current status |
| of the dock, as provided by the ACPI framework. |
| |
| The docking support in this driver does not take care of enabling or |
| disabling any other devices you may have attached to the dock. For |
| example, a CD drive plugged into the UltraBase needs to be disabled or |
| enabled separately. See the provided example acpid configuration files |
| for how this can be accomplished. |
| |
| There is no support yet for PCI devices that may be attached to a |
| docking station, e.g. in the ThinkPad Dock II. The driver currently |
| does not recognize, enable or disable such devices. This means that |
| the only docking stations currently supported are the X-series |
| UltraBase docks and "dumb" port replicators like the Mini Dock (the |
| latter don't need any ACPI support, actually). |
| |
| |
| UltraBay eject -- /proc/acpi/ibm/bay |
| ------------------------------------ |
| |
| Inserting or ejecting an UltraBay device requires some actions to be |
| taken by the operating system to safely make or break the electrical |
| connections with the device. |
| |
| This feature generates the following ACPI events: |
| |
| ibm/bay MSTR 00000003 00000000 -- eject request |
| ibm/bay MSTR 00000001 00000000 -- eject lever inserted |
| |
| NOTE: These events will only be generated if the UltraBay was present |
| when the laptop was originally booted (on the X series, the UltraBay |
| is in the dock, so it may not be present if the laptop was undocked). |
| This is due to the current lack of support for hot plugging of devices |
| in the Linux ACPI framework. If the laptop was booted without the |
| UltraBay, the following message is shown in the logs: |
| |
| Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present |
| |
| In this case, no bay-related events are generated but the eject |
| command described below still works. It can be executed manually or |
| triggered by a hot key combination. |
| |
| Sliding the eject lever generates the first event shown above. The |
| handler for this event should take whatever actions are necessary to |
| shut down the device in the UltraBay (e.g. call idectl), then issue |
| the following command: |
| |
| echo eject > /proc/acpi/ibm/bay |
| |
| After the LED on the UltraBay goes off, it is safe to pull out the |
| device. |
| |
| When the eject lever is inserted, the second event above is |
| generated. The handler for this event should take whatever actions are |
| necessary to enable the UltraBay device (e.g. call idectl). |
| |
| The contents of the /proc/acpi/ibm/bay file shows the current status |
| of the UltraBay, as provided by the ACPI framework. |
| |
| EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use |
| this feature, you need to supply the experimental=1 parameter when |
| loading the module): |
| |
| These models do not have a button near the UltraBay device to request |
| a hot eject but rather require the laptop to be put to sleep |
| (suspend-to-ram) before the bay device is ejected or inserted). |
| The sequence of steps to eject the device is as follows: |
| |
| echo eject > /proc/acpi/ibm/bay |
| put the ThinkPad to sleep |
| remove the drive |
| resume from sleep |
| cat /proc/acpi/ibm/bay should show that the drive was removed |
| |
| On the A3x, both the UltraBay 2000 and UltraBay Plus devices are |
| supported. Use "eject2" instead of "eject" for the second bay. |
| |
| Note: the UltraBay eject support on the 600e/x, A22p and A3x is |
| EXPERIMENTAL and may not work as expected. USE WITH CAUTION! |
| |
| |
| CMOS/UCMS control |
| ----------------- |
| |
| procfs: /proc/acpi/ibm/cmos |
| sysfs device attribute: cmos_command |
| |
| This feature is mostly used internally by the ACPI firmware to keep the legacy |
| CMOS NVRAM bits in sync with the current machine state, and to record this |
| state so that the ThinkPad will retain such settings across reboots. |
| |
| Some of these commands actually perform actions in some ThinkPad models, but |
| this is expected to disappear more and more in newer models. As an example, in |
| a T43 and in a X40, commands 12 and 13 still control the ThinkLight state for |
| real, but commands 0 to 2 don't control the mixer anymore (they have been |
| phased out) and just update the NVRAM. |
| |
| The range of valid cmos command numbers is 0 to 21, but not all have an |
| effect and the behavior varies from model to model. Here is the behavior |
| on the X40 (tpb is the ThinkPad Buttons utility): |
| |
| 0 - Related to "Volume down" key press |
| 1 - Related to "Volume up" key press |
| 2 - Related to "Mute on" key press |
| 3 - Related to "Access IBM" key press |
| 4 - Related to "LCD brightness up" key press |
| 5 - Related to "LCD brightness down" key press |
| 11 - Related to "toggle screen expansion" key press/function |
| 12 - Related to "ThinkLight on" |
| 13 - Related to "ThinkLight off" |
| 14 - Related to "ThinkLight" key press (toggle ThinkLight) |
| |
| The cmos command interface is prone to firmware split-brain problems, as |
| in newer ThinkPads it is just a compatibility layer. Do not use it, it is |
| exported just as a debug tool. |
| |
| |
| LED control |
| ----------- |
| |
| procfs: /proc/acpi/ibm/led |
| sysfs attributes: as per LED class, see below for names |
| |
| Some of the LED indicators can be controlled through this feature. On |
| some older ThinkPad models, it is possible to query the status of the |
| LED indicators as well. Newer ThinkPads cannot query the real status |
| of the LED indicators. |
| |
| procfs notes: |
| |
| The available commands are: |
| |
| echo '<LED number> on' >/proc/acpi/ibm/led |
| echo '<LED number> off' >/proc/acpi/ibm/led |
| echo '<LED number> blink' >/proc/acpi/ibm/led |
| |
| The <LED number> range is 0 to 7. The set of LEDs that can be |
| controlled varies from model to model. Here is the common ThinkPad |
| mapping: |
| |
| 0 - power |
| 1 - battery (orange) |
| 2 - battery (green) |
| 3 - UltraBase/dock |
| 4 - UltraBay |
| 5 - UltraBase battery slot |
| 6 - (unknown) |
| 7 - standby |
| |
| All of the above can be turned on and off and can be made to blink. |
| |
| sysfs notes: |
| |
| The ThinkPad LED sysfs interface is described in detail by the LED class |
| documentation, in Documentation/leds-class.txt. |
| |
| The leds are named (in LED ID order, from 0 to 7): |
| "tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt", |
| "tpacpi::dock_active", "tpacpi::bay_active", "tpacpi::dock_batt", |
| "tpacpi::unknown_led", "tpacpi::standby". |
| |
| Due to limitations in the sysfs LED class, if the status of the LED |
| indicators cannot be read due to an error, thinkpad-acpi will report it as |
| a brightness of zero (same as LED off). |
| |
| If the thinkpad firmware doesn't support reading the current status, |
| trying to read the current LED brightness will just return whatever |
| brightness was last written to that attribute. |
| |
| These LEDs can blink using hardware acceleration. To request that a |
| ThinkPad indicator LED should blink in hardware accelerated mode, use the |
| "timer" trigger, and leave the delay_on and delay_off parameters set to |
| zero (to request hardware acceleration autodetection). |
| |
| |
| ACPI sounds -- /proc/acpi/ibm/beep |
| ---------------------------------- |
| |
| The BEEP method is used internally by the ACPI firmware to provide |
| audible alerts in various situations. This feature allows the same |
| sounds to be triggered manually. |
| |
| The commands are non-negative integer numbers: |
| |
| echo <number> >/proc/acpi/ibm/beep |
| |
| The valid <number> range is 0 to 17. Not all numbers trigger sounds |
| and the sounds vary from model to model. Here is the behavior on the |
| X40: |
| |
| 0 - stop a sound in progress (but use 17 to stop 16) |
| 2 - two beeps, pause, third beep ("low battery") |
| 3 - single beep |
| 4 - high, followed by low-pitched beep ("unable") |
| 5 - single beep |
| 6 - very high, followed by high-pitched beep ("AC/DC") |
| 7 - high-pitched beep |
| 9 - three short beeps |
| 10 - very long beep |
| 12 - low-pitched beep |
| 15 - three high-pitched beeps repeating constantly, stop with 0 |
| 16 - one medium-pitched beep repeating constantly, stop with 17 |
| 17 - stop 16 |
| |
| |
| Temperature sensors |
| ------------------- |
| |
| procfs: /proc/acpi/ibm/thermal |
| sysfs device attributes: (hwmon "thinkpad") temp*_input |
| |
| Most ThinkPads include six or more separate temperature sensors but only |
| expose the CPU temperature through the standard ACPI methods. This |
| feature shows readings from up to eight different sensors on older |
| ThinkPads, and up to sixteen different sensors on newer ThinkPads. |
| |
| For example, on the X40, a typical output may be: |
| temperatures: 42 42 45 41 36 -128 33 -128 |
| |
| On the T43/p, a typical output may be: |
| temperatures: 48 48 36 52 38 -128 31 -128 48 52 48 -128 -128 -128 -128 -128 |
| |
| The mapping of thermal sensors to physical locations varies depending on |
| system-board model (and thus, on ThinkPad model). |
| |
| http://thinkwiki.org/wiki/Thermal_Sensors is a public wiki page that |
| tries to track down these locations for various models. |
| |
| Most (newer?) models seem to follow this pattern: |
| |
| 1: CPU |
| 2: (depends on model) |
| 3: (depends on model) |
| 4: GPU |
| 5: Main battery: main sensor |
| 6: Bay battery: main sensor |
| 7: Main battery: secondary sensor |
| 8: Bay battery: secondary sensor |
| 9-15: (depends on model) |
| |
| For the R51 (source: Thomas Gruber): |
| 2: Mini-PCI |
| 3: Internal HDD |
| |
| For the T43, T43/p (source: Shmidoax/Thinkwiki.org) |
| http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_T43.2C_T43p |
| 2: System board, left side (near PCMCIA slot), reported as HDAPS temp |
| 3: PCMCIA slot |
| 9: MCH (northbridge) to DRAM Bus |
| 10: Clock-generator, mini-pci card and ICH (southbridge), under Mini-PCI |
| card, under touchpad |
| 11: Power regulator, underside of system board, below F2 key |
| |
| The A31 has a very atypical layout for the thermal sensors |
| (source: Milos Popovic, http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_A31) |
| 1: CPU |
| 2: Main Battery: main sensor |
| 3: Power Converter |
| 4: Bay Battery: main sensor |
| 5: MCH (northbridge) |
| 6: PCMCIA/ambient |
| 7: Main Battery: secondary sensor |
| 8: Bay Battery: secondary sensor |
| |
| |
| Procfs notes: |
| Readings from sensors that are not available return -128. |
| No commands can be written to this file. |
| |
| Sysfs notes: |
| Sensors that are not available return the ENXIO error. This |
| status may change at runtime, as there are hotplug thermal |
| sensors, like those inside the batteries and docks. |
| |
| thinkpad-acpi thermal sensors are reported through the hwmon |
| subsystem, and follow all of the hwmon guidelines at |
| Documentation/hwmon. |
| |
| |
| EXPERIMENTAL: Embedded controller register dump -- /proc/acpi/ibm/ecdump |
| ------------------------------------------------------------------------ |
| |
| This feature is marked EXPERIMENTAL because the implementation |
| directly accesses hardware registers and may not work as expected. USE |
| WITH CAUTION! To use this feature, you need to supply the |
| experimental=1 parameter when loading the module. |
| |
| This feature dumps the values of 256 embedded controller |
| registers. Values which have changed since the last time the registers |
| were dumped are marked with a star: |
| |
| [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump |
| EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f |
| EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 |
| EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 |
| EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 |
| EC 0x30: 01 07 1a 00 30 04 00 00 *85 00 00 10 00 50 00 00 |
| EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 |
| EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 *bc *02 *bc |
| EC 0x60: *02 *bc *02 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0x70: 00 00 00 00 00 12 30 40 *24 *26 *2c *27 *20 80 *1f 80 |
| EC 0x80: 00 00 00 06 *37 *0e 03 00 00 00 0e 07 00 00 00 00 |
| EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xa0: *ff 09 ff 09 ff ff *64 00 *00 *00 *a2 41 *ff *ff *e0 00 |
| EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 |
| EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a |
| |
| This feature can be used to determine the register holding the fan |
| speed on some models. To do that, do the following: |
| |
| - make sure the battery is fully charged |
| - make sure the fan is running |
| - run 'cat /proc/acpi/ibm/ecdump' several times, once per second or so |
| |
| The first step makes sure various charging-related values don't |
| vary. The second ensures that the fan-related values do vary, since |
| the fan speed fluctuates a bit. The third will (hopefully) mark the |
| fan register with a star: |
| |
| [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump |
| EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f |
| EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 |
| EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 |
| EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 |
| EC 0x30: 01 07 1a 00 30 04 00 00 85 00 00 10 00 50 00 00 |
| EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 |
| EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 bc 02 bc |
| EC 0x60: 02 bc 02 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0x70: 00 00 00 00 00 12 30 40 24 27 2c 27 21 80 1f 80 |
| EC 0x80: 00 00 00 06 *be 0d 03 00 00 00 0e 07 00 00 00 00 |
| EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xa0: ff 09 ff 09 ff ff 64 00 00 00 a2 41 ff ff e0 00 |
| EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 |
| EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a |
| |
| Another set of values that varies often is the temperature |
| readings. Since temperatures don't change vary fast, you can take |
| several quick dumps to eliminate them. |
| |
| You can use a similar method to figure out the meaning of other |
| embedded controller registers - e.g. make sure nothing else changes |
| except the charging or discharging battery to determine which |
| registers contain the current battery capacity, etc. If you experiment |
| with this, do send me your results (including some complete dumps with |
| a description of the conditions when they were taken.) |
| |
| |
| LCD brightness control |
| ---------------------- |
| |
| procfs: /proc/acpi/ibm/brightness |
| sysfs backlight device "thinkpad_screen" |
| |
| This feature allows software control of the LCD brightness on ThinkPad |
| models which don't have a hardware brightness slider. |
| |
| It has some limitations: the LCD backlight cannot be actually turned |
| on or off by this interface, it just controls the backlight brightness |
| level. |
| |
| On IBM (and some of the earlier Lenovo) ThinkPads, the backlight control |
| has eight brightness levels, ranging from 0 to 7. Some of the levels |
| may not be distinct. Later Lenovo models that implement the ACPI |
| display backlight brightness control methods have 16 levels, ranging |
| from 0 to 15. |
| |
| There are two interfaces to the firmware for direct brightness control, |
| EC and CMOS. To select which one should be used, use the |
| brightness_mode module parameter: brightness_mode=1 selects EC mode, |
| brightness_mode=2 selects CMOS mode, brightness_mode=3 selects both EC |
| and CMOS. The driver tries to auto-detect which interface to use. |
| |
| When display backlight brightness controls are available through the |
| standard ACPI interface, it is best to use it instead of this direct |
| ThinkPad-specific interface. The driver will disable its native |
| backlight brightness control interface if it detects that the standard |
| ACPI interface is available in the ThinkPad. |
| |
| The brightness_enable module parameter can be used to control whether |
| the LCD brightness control feature will be enabled when available. |
| brightness_enable=0 forces it to be disabled. brightness_enable=1 |
| forces it to be enabled when available, even if the standard ACPI |
| interface is also available. |
| |
| Procfs notes: |
| |
| The available commands are: |
| |
| echo up >/proc/acpi/ibm/brightness |
| echo down >/proc/acpi/ibm/brightness |
| echo 'level <level>' >/proc/acpi/ibm/brightness |
| |
| Sysfs notes: |
| |
| The interface is implemented through the backlight sysfs class, which is |
| poorly documented at this time. |
| |
| Locate the thinkpad_screen device under /sys/class/backlight, and inside |
| it there will be the following attributes: |
| |
| max_brightness: |
| Reads the maximum brightness the hardware can be set to. |
| The minimum is always zero. |
| |
| actual_brightness: |
| Reads what brightness the screen is set to at this instant. |
| |
| brightness: |
| Writes request the driver to change brightness to the |
| given value. Reads will tell you what brightness the |
| driver is trying to set the display to when "power" is set |
| to zero and the display has not been dimmed by a kernel |
| power management event. |
| |
| power: |
| power management mode, where 0 is "display on", and 1 to 3 |
| will dim the display backlight to brightness level 0 |
| because thinkpad-acpi cannot really turn the backlight |
| off. Kernel power management events can temporarily |
| increase the current power management level, i.e. they can |
| dim the display. |
| |
| |
| WARNING: |
| |
| Whatever you do, do NOT ever call thinkpad-acpi backlight-level change |
| interface and the ACPI-based backlight level change interface |
| (available on newer BIOSes, and driven by the Linux ACPI video driver) |
| at the same time. The two will interact in bad ways, do funny things, |
| and maybe reduce the life of the backlight lamps by needlessly kicking |
| its level up and down at every change. |
| |
| |
| Volume control -- /proc/acpi/ibm/volume |
| --------------------------------------- |
| |
| This feature allows volume control on ThinkPad models which don't have |
| a hardware volume knob. The available commands are: |
| |
| echo up >/proc/acpi/ibm/volume |
| echo down >/proc/acpi/ibm/volume |
| echo mute >/proc/acpi/ibm/volume |
| echo 'level <level>' >/proc/acpi/ibm/volume |
| |
| The <level> number range is 0 to 15 although not all of them may be |
| distinct. The unmute the volume after the mute command, use either the |
| up or down command (the level command will not unmute the volume). |
| The current volume level and mute state is shown in the file. |
| |
| The ALSA mixer interface to this feature is still missing, but patches |
| to add it exist. That problem should be addressed in the not so |
| distant future. |
| |
| |
| Fan control and monitoring: fan speed, fan enable/disable |
| --------------------------------------------------------- |
| |
| procfs: /proc/acpi/ibm/fan |
| sysfs device attributes: (hwmon "thinkpad") fan1_input, pwm1, |
| pwm1_enable |
| sysfs hwmon driver attributes: fan_watchdog |
| |
| NOTE NOTE NOTE: fan control operations are disabled by default for |
| safety reasons. To enable them, the module parameter "fan_control=1" |
| must be given to thinkpad-acpi. |
| |
| This feature attempts to show the current fan speed, control mode and |
| other fan data that might be available. The speed is read directly |
| from the hardware registers of the embedded controller. This is known |
| to work on later R, T, X and Z series ThinkPads but may show a bogus |
| value on other models. |
| |
| Fan levels: |
| |
| Most ThinkPad fans work in "levels" at the firmware interface. Level 0 |
| stops the fan. The higher the level, the higher the fan speed, although |
| adjacent levels often map to the same fan speed. 7 is the highest |
| level, where the fan reaches the maximum recommended speed. |
| |
| Level "auto" means the EC changes the fan level according to some |
| internal algorithm, usually based on readings from the thermal sensors. |
| |
| There is also a "full-speed" level, also known as "disengaged" level. |
| In this level, the EC disables the speed-locked closed-loop fan control, |
| and drives the fan as fast as it can go, which might exceed hardware |
| limits, so use this level with caution. |
| |
| The fan usually ramps up or down slowly from one speed to another, and |
| it is normal for the EC to take several seconds to react to fan |
| commands. The full-speed level may take up to two minutes to ramp up to |
| maximum speed, and in some ThinkPads, the tachometer readings go stale |
| while the EC is transitioning to the full-speed level. |
| |
| WARNING WARNING WARNING: do not leave the fan disabled unless you are |
| monitoring all of the temperature sensor readings and you are ready to |
| enable it if necessary to avoid overheating. |
| |
| An enabled fan in level "auto" may stop spinning if the EC decides the |
| ThinkPad is cool enough and doesn't need the extra airflow. This is |
| normal, and the EC will spin the fan up if the various thermal readings |
| rise too much. |
| |
| On the X40, this seems to depend on the CPU and HDD temperatures. |
| Specifically, the fan is turned on when either the CPU temperature |
| climbs to 56 degrees or the HDD temperature climbs to 46 degrees. The |
| fan is turned off when the CPU temperature drops to 49 degrees and the |
| HDD temperature drops to 41 degrees. These thresholds cannot |
| currently be controlled. |
| |
| The ThinkPad's ACPI DSDT code will reprogram the fan on its own when |
| certain conditions are met. It will override any fan programming done |
| through thinkpad-acpi. |
| |
| The thinkpad-acpi kernel driver can be programmed to revert the fan |
| level to a safe setting if userspace does not issue one of the procfs |
| fan commands: "enable", "disable", "level" or "watchdog", or if there |
| are no writes to pwm1_enable (or to pwm1 *if and only if* pwm1_enable is |
| set to 1, manual mode) within a configurable amount of time of up to |
| 120 seconds. This functionality is called fan safety watchdog. |
| |
| Note that the watchdog timer stops after it enables the fan. It will be |
| rearmed again automatically (using the same interval) when one of the |
| above mentioned fan commands is received. The fan watchdog is, |
| therefore, not suitable to protect against fan mode changes made through |
| means other than the "enable", "disable", and "level" procfs fan |
| commands, or the hwmon fan control sysfs interface. |
| |
| Procfs notes: |
| |
| The fan may be enabled or disabled with the following commands: |
| |
| echo enable >/proc/acpi/ibm/fan |
| echo disable >/proc/acpi/ibm/fan |
| |
| Placing a fan on level 0 is the same as disabling it. Enabling a fan |
| will try to place it in a safe level if it is too slow or disabled. |
| |
| The fan level can be controlled with the command: |
| |
| echo 'level <level>' > /proc/acpi/ibm/fan |
| |
| Where <level> is an integer from 0 to 7, or one of the words "auto" or |
| "full-speed" (without the quotes). Not all ThinkPads support the "auto" |
| and "full-speed" levels. The driver accepts "disengaged" as an alias for |
| "full-speed", and reports it as "disengaged" for backwards |
| compatibility. |
| |
| On the X31 and X40 (and ONLY on those models), the fan speed can be |
| controlled to a certain degree. Once the fan is running, it can be |
| forced to run faster or slower with the following command: |
| |
| echo 'speed <speed>' > /proc/acpi/ibm/fan |
| |
| The sustainable range of fan speeds on the X40 appears to be from about |
| 3700 to about 7350. Values outside this range either do not have any |
| effect or the fan speed eventually settles somewhere in that range. The |
| fan cannot be stopped or started with this command. This functionality |
| is incomplete, and not available through the sysfs interface. |
| |
| To program the safety watchdog, use the "watchdog" command. |
| |
| echo 'watchdog <interval in seconds>' > /proc/acpi/ibm/fan |
| |
| If you want to disable the watchdog, use 0 as the interval. |
| |
| Sysfs notes: |
| |
| The sysfs interface follows the hwmon subsystem guidelines for the most |
| part, and the exception is the fan safety watchdog. |
| |
| Writes to any of the sysfs attributes may return the EINVAL error if |
| that operation is not supported in a given ThinkPad or if the parameter |
| is out-of-bounds, and EPERM if it is forbidden. They may also return |
| EINTR (interrupted system call), and EIO (I/O error while trying to talk |
| to the firmware). |
| |
| Features not yet implemented by the driver return ENOSYS. |
| |
| hwmon device attribute pwm1_enable: |
| 0: PWM offline (fan is set to full-speed mode) |
| 1: Manual PWM control (use pwm1 to set fan level) |
| 2: Hardware PWM control (EC "auto" mode) |
| 3: reserved (Software PWM control, not implemented yet) |
| |
| Modes 0 and 2 are not supported by all ThinkPads, and the |
| driver is not always able to detect this. If it does know a |
| mode is unsupported, it will return -EINVAL. |
| |
| hwmon device attribute pwm1: |
| Fan level, scaled from the firmware values of 0-7 to the hwmon |
| scale of 0-255. 0 means fan stopped, 255 means highest normal |
| speed (level 7). |
| |
| This attribute only commands the fan if pmw1_enable is set to 1 |
| (manual PWM control). |
| |
| hwmon device attribute fan1_input: |
| Fan tachometer reading, in RPM. May go stale on certain |
| ThinkPads while the EC transitions the PWM to offline mode, |
| which can take up to two minutes. May return rubbish on older |
| ThinkPads. |
| |
| hwmon driver attribute fan_watchdog: |
| Fan safety watchdog timer interval, in seconds. Minimum is |
| 1 second, maximum is 120 seconds. 0 disables the watchdog. |
| |
| To stop the fan: set pwm1 to zero, and pwm1_enable to 1. |
| |
| To start the fan in a safe mode: set pwm1_enable to 2. If that fails |
| with EINVAL, try to set pwm1_enable to 1 and pwm1 to at least 128 (255 |
| would be the safest choice, though). |
| |
| |
| WAN |
| --- |
| |
| procfs: /proc/acpi/ibm/wan |
| sysfs device attribute: wwan_enable (deprecated) |
| sysfs rfkill class: switch "tpacpi_wwan_sw" |
| |
| This feature shows the presence and current state of the built-in |
| Wireless WAN device. |
| |
| If the ThinkPad supports it, the WWAN state is stored in NVRAM, |
| so it is kept across reboots and power-off. |
| |
| It was tested on a Lenovo ThinkPad X60. It should probably work on other |
| ThinkPad models which come with this module installed. |
| |
| Procfs notes: |
| |
| If the W-WAN card is installed, the following commands can be used: |
| |
| echo enable > /proc/acpi/ibm/wan |
| echo disable > /proc/acpi/ibm/wan |
| |
| Sysfs notes: |
| |
| If the W-WAN card is installed, it can be enabled / |
| disabled through the "wwan_enable" thinkpad-acpi device |
| attribute, and its current status can also be queried. |
| |
| enable: |
| 0: disables WWAN card / WWAN card is disabled |
| 1: enables WWAN card / WWAN card is enabled. |
| |
| Note: this interface has been superseded by the generic rfkill |
| class. It has been deprecated, and it will be removed in year |
| 2010. |
| |
| rfkill controller switch "tpacpi_wwan_sw": refer to |
| Documentation/rfkill.txt for details. |
| |
| |
| EXPERIMENTAL: UWB |
| ----------------- |
| |
| This feature is marked EXPERIMENTAL because it has not been extensively |
| tested and validated in various ThinkPad models yet. The feature may not |
| work as expected. USE WITH CAUTION! To use this feature, you need to supply |
| the experimental=1 parameter when loading the module. |
| |
| sysfs rfkill class: switch "tpacpi_uwb_sw" |
| |
| This feature exports an rfkill controller for the UWB device, if one is |
| present and enabled in the BIOS. |
| |
| Sysfs notes: |
| |
| rfkill controller switch "tpacpi_uwb_sw": refer to |
| Documentation/rfkill.txt for details. |
| |
| |
| Multiple Commands, Module Parameters |
| ------------------------------------ |
| |
| Multiple commands can be written to the proc files in one shot by |
| separating them with commas, for example: |
| |
| echo enable,0xffff > /proc/acpi/ibm/hotkey |
| echo lcd_disable,crt_enable > /proc/acpi/ibm/video |
| |
| Commands can also be specified when loading the thinkpad-acpi module, |
| for example: |
| |
| modprobe thinkpad_acpi hotkey=enable,0xffff video=auto_disable |
| |
| |
| Enabling debugging output |
| ------------------------- |
| |
| The module takes a debug parameter which can be used to selectively |
| enable various classes of debugging output, for example: |
| |
| modprobe thinkpad_acpi debug=0xffff |
| |
| will enable all debugging output classes. It takes a bitmask, so |
| to enable more than one output class, just add their values. |
| |
| Debug bitmask Description |
| 0x8000 Disclose PID of userspace programs |
| accessing some functions of the driver |
| 0x0001 Initialization and probing |
| 0x0002 Removal |
| |
| There is also a kernel build option to enable more debugging |
| information, which may be necessary to debug driver problems. |
| |
| The level of debugging information output by the driver can be changed |
| at runtime through sysfs, using the driver attribute debug_level. The |
| attribute takes the same bitmask as the debug module parameter above. |
| |
| |
| Force loading of module |
| ----------------------- |
| |
| If thinkpad-acpi refuses to detect your ThinkPad, you can try to specify |
| the module parameter force_load=1. Regardless of whether this works or |
| not, please contact ibm-acpi-devel@lists.sourceforge.net with a report. |
| |
| |
| Sysfs interface changelog: |
| |
| 0x000100: Initial sysfs support, as a single platform driver and |
| device. |
| 0x000200: Hot key support for 32 hot keys, and radio slider switch |
| support. |
| 0x010000: Hot keys are now handled by default over the input |
| layer, the radio switch generates input event EV_RADIO, |
| and the driver enables hot key handling by default in |
| the firmware. |
| |
| 0x020000: ABI fix: added a separate hwmon platform device and |
| driver, which must be located by name (thinkpad) |
| and the hwmon class for libsensors4 (lm-sensors 3) |
| compatibility. Moved all hwmon attributes to this |
| new platform device. |
| |
| 0x020100: Marker for thinkpad-acpi with hot key NVRAM polling |
| support. If you must, use it to know you should not |
| start a userspace NVRAM poller (allows to detect when |
| NVRAM is compiled out by the user because it is |
| unneeded/undesired in the first place). |
| 0x020101: Marker for thinkpad-acpi with hot key NVRAM polling |
| and proper hotkey_mask semantics (version 8 of the |
| NVRAM polling patch). Some development snapshots of |
| 0.18 had an earlier version that did strange things |
| to hotkey_mask. |
| |
| 0x020200: Add poll()/select() support to the following attributes: |
| hotkey_radio_sw, wakeup_hotunplug_complete, wakeup_reason |
| |
| 0x020300: hotkey enable/disable support removed, attributes |
| hotkey_bios_enabled and hotkey_enable deprecated and |
| marked for removal. |