| config SND_BF5XX_I2S |
| tristate "SoC I2S Audio for the ADI Blackfin chip" |
| depends on BLACKFIN |
| select SND_BF5XX_SOC_SPORT if !BF60x |
| select SND_BF6XX_SOC_SPORT if BF60x |
| help |
| Say Y or M if you want to add support for codecs attached to |
| the Blackfin SPORT (synchronous serial ports) interface in I2S |
| mode (supports single stereo In/Out). |
| You will also need to select the audio interfaces to support below. |
| |
| config SND_BF5XX_SOC_SSM2602 |
| tristate "SoC SSM2602 Audio Codec Add-On Card support" |
| depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI |
| select SND_BF5XX_SOC_I2S if !BF60x |
| select SND_BF6XX_SOC_I2S if BF60x |
| select SND_SOC_SSM2602_SPI if SPI_MASTER |
| select SND_SOC_SSM2602_I2C if I2C |
| help |
| Say Y if you want to add support for the Analog Devices |
| SSM2602 Audio Codec Add-On Card. |
| |
| config SND_SOC_BFIN_EVAL_ADAU1701 |
| tristate "Support for the EVAL-ADAU1701MINIZ board on Blackfin eval boards" |
| depends on SND_BF5XX_I2S && I2C |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_ADAU1701 |
| help |
| Say Y if you want to add support for the Analog Devices EVAL-ADAU1701MINIZ |
| board connected to one of the Blackfin evaluation boards like the |
| BF5XX-STAMP or BF5XX-EZKIT. |
| |
| config SND_SOC_BFIN_EVAL_ADAU1373 |
| tristate "Support for the EVAL-ADAU1373 board on Blackfin eval boards" |
| depends on SND_BF5XX_I2S && I2C |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_ADAU1373 |
| help |
| Say Y if you want to add support for the Analog Devices EVAL-ADAU1373 |
| board connected to one of the Blackfin evaluation boards like the |
| BF5XX-STAMP or BF5XX-EZKIT. |
| |
| Note: This driver assumes that first ADAU1373 DAI is connected to the |
| first SPORT port on the BF5XX board. |
| |
| config SND_SOC_BFIN_EVAL_ADAV80X |
| tristate "Support for the EVAL-ADAV80X boards on Blackfin eval boards" |
| depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_ADAV801 if SPI_MASTER |
| select SND_SOC_ADAV803 if I2C |
| help |
| Say Y if you want to add support for the Analog Devices EVAL-ADAV801 or |
| EVAL-ADAV803 board connected to one of the Blackfin evaluation boards |
| like the BF5XX-STAMP or BF5XX-EZKIT. |
| |
| Note: This driver assumes that the ADAV80X digital record and playback |
| interfaces are connected to the first SPORT port on the BF5XX board. |
| |
| config SND_BF5XX_SOC_AD1836 |
| tristate "SoC AD1836 Audio support for BF5xx" |
| depends on SND_BF5XX_I2S && SPI_MASTER |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_AD1836 |
| help |
| Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. |
| |
| config SND_BF5XX_SOC_AD193X |
| tristate "SoC AD193X Audio support for Blackfin" |
| depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_AD193X_I2C if I2C |
| select SND_SOC_AD193X_SPI if SPI_MASTER |
| help |
| Say Y if you want to add support for AD193X codec on Blackfin. |
| This driver supports AD1936, AD1937, AD1938 and AD1939. |
| |
| config SND_BF5XX_SOC_AD73311 |
| tristate "SoC AD73311 Audio support for Blackfin" |
| depends on SND_BF5XX_I2S |
| select SND_BF5XX_SOC_I2S |
| select SND_SOC_AD73311 |
| help |
| Say Y if you want to add support for AD73311 codec on Blackfin. |
| |
| config SND_BFIN_AD73311_SE |
| int "PF pin for AD73311L Chip Select" |
| depends on SND_BF5XX_SOC_AD73311 |
| default 4 |
| help |
| Enter the GPIO used to control AD73311's SE pin. Acceptable |
| values are 0 to 7 |
| |
| config SND_BF5XX_AC97 |
| tristate "SoC AC97 Audio for the ADI BF5xx chip" |
| depends on BLACKFIN |
| select AC97_BUS |
| select SND_SOC_AC97_BUS |
| select SND_BF5XX_SOC_SPORT |
| select SND_BF5XX_SOC_AC97 |
| help |
| Say Y or M if you want to add support for codecs attached to |
| the Blackfin SPORT (synchronous serial ports) interface in slot 16 |
| mode (pseudo AC97 interface). |
| You will also need to select the audio interfaces to support below. |
| |
| Note: |
| AC97 codecs which do not implement the slot-16 mode will not function |
| properly with this driver. This driver is known to work with the |
| Analog Devices line of AC97 codecs. |
| |
| config SND_BF5XX_MMAP_SUPPORT |
| bool "Enable MMAP Support" |
| depends on SND_BF5XX_AC97 |
| default y |
| help |
| Say y if you want AC97 driver to support mmap mode. |
| We introduce an intermediate buffer to simulate mmap. |
| |
| config SND_BF5XX_MULTICHAN_SUPPORT |
| bool "Enable Multichannel Support" |
| depends on SND_BF5XX_AC97 |
| default n |
| help |
| Say y if you want AC97 driver to support up to 5.1 channel audio. |
| this mode will consume much more memory for DMA. |
| |
| config SND_BF5XX_HAVE_COLD_RESET |
| bool "BOARD has COLD Reset GPIO" |
| depends on SND_BF5XX_AC97 |
| default y if BFIN548_EZKIT |
| default n if !BFIN548_EZKIT |
| |
| config SND_BF5XX_RESET_GPIO_NUM |
| int "Set a GPIO for cold reset" |
| depends on SND_BF5XX_HAVE_COLD_RESET |
| range 0 159 |
| default 19 if BFIN548_EZKIT |
| default 5 if BFIN537_STAMP |
| default 0 |
| help |
| Set the correct GPIO for RESET the sound chip. |
| |
| config SND_BF5XX_SOC_AD1980 |
| tristate "SoC AD1980/1 Audio support for BF5xx (Obsolete)" |
| depends on SND_BF5XX_AC97 |
| select SND_BF5XX_SOC_AC97 |
| select SND_SOC_AD1980 |
| help |
| Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. |
| |
| Warning: |
| Because Analog Devices Inc. discontinued the ad1980 sound chip since |
| Sep. 2009, this ad1980 driver is not maintained, tested and supported |
| by ADI now. |
| |
| config SND_BF5XX_SOC_SPORT |
| tristate |
| |
| config SND_BF6XX_SOC_SPORT |
| tristate |
| |
| config SND_BF5XX_SOC_I2S |
| tristate |
| |
| config SND_BF6XX_SOC_I2S |
| tristate |
| |
| config SND_BF5XX_SOC_AC97 |
| tristate |
| |
| config SND_BF5XX_SPORT_NUM |
| int "Set a SPORT for Sound chip" |
| depends on (SND_BF5XX_SOC_SPORT || SND_BF6XX_SOC_SPORT) |
| range 0 3 if BF54x |
| range 0 1 if !BF54x |
| default 0 |
| help |
| Set the correct SPORT for sound chip. |
