blob: db64c908d4a73b31e3dacd67abf85573a4782256 [file] [log] [blame]
#
# USB Network devices configuration
#
comment "Networking support is needed for USB Network Adapter support"
depends on USB && !NET
menu "USB Network Adapters"
depends on USB && NET
config USB_CATC
tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
depends on EXPERIMENTAL
select CRC32
---help---
Say Y if you want to use one of the following 10Mbps USB Ethernet
device based on the EL1210A chip. Supported devices are:
Belkin F5U011
Belkin F5U111
CATC NetMate
CATC NetMate II
smartBridges smartNIC
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
To compile this driver as a module, choose M here: the
module will be called catc.
config USB_KAWETH
tristate "USB KLSI KL5USB101-based ethernet device support"
---help---
Say Y here if you want to use one of the following 10Mbps only
USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
3Com 3C19250
ADS USB-10BT
ATEN USB Ethernet
ASANTE USB To Ethernet Adapter
AOX Endpoints USB Ethernet
Correga K.K.
D-Link DSB-650C and DU-E10
Entrega / Portgear E45
I-O DATA USB-ET/T
Jaton USB Ethernet Device Adapter
Kingston Technology USB Ethernet Adapter
Linksys USB10T
Mobility USB-Ethernet Adapter
NetGear EA-101
Peracom Enet and Enet2
Portsmith Express Ethernet Adapter
Shark Pocket Adapter
SMC 2202USB
Sony Vaio port extender
This driver is likely to work with most 10Mbps only USB Ethernet
adapters, including some "no brand" devices. It does NOT work on
SmartBridges smartNIC or on Belkin F5U111 devices - you should use
the CATC NetMate driver for those. If you are not sure which one
you need, select both, and the correct one should be selected for
you.
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
To compile this driver as a module, choose M here: the
module will be called kaweth.
config USB_PEGASUS
tristate "USB Pegasus/Pegasus-II based ethernet device support"
select MII
---help---
Say Y here if you know you have Pegasus or Pegasus-II based adapter.
If in doubt then look at <file:drivers/usb/net/pegasus.h> for the
complete list of supported devices.
If your particular adapter is not in the list and you are _sure_ it
is Pegasus or Pegasus II based then send me
<petkan@users.sourceforge.net> vendor and device IDs.
To compile this driver as a module, choose M here: the
module will be called pegasus.
config USB_RTL8150
tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
Say Y here if you have RTL8150 based usb-ethernet adapter.
Send me <petkan@users.sourceforge.net> any comments you may have.
You can also check for updates at <http://pegasus2.sourceforge.net/>.
To compile this driver as a module, choose M here: the
module will be called rtl8150.
config USB_USBNET
tristate "Multi-purpose USB Networking Framework"
---help---
This driver supports several kinds of network links over USB,
with "minidrivers" built around a common network driver core
that supports deep queues for efficient transfers. (This gives
better performance with small packets and at high speeds).
The USB host runs "usbnet", and the other end of the link might be:
- Another USB host, when using USB "network" or "data transfer"
cables. These are often used to network laptops to PCs, like
"Laplink" parallel cables or some motherboards. These rely
on specialized chips from many suppliers.
- An intelligent USB gadget, perhaps embedding a Linux system.
These include PDAs running Linux (iPaq, Yopy, Zaurus, and
others), and devices that interoperate using the standard
CDC-Ethernet specification (including many cable modems).
- Network adapter hardware (like those for 10/100 Ethernet) which
uses this driver framework.
The link will appear with a name like "usb0", when the link is
a two-node link, or "eth0" for most CDC-Ethernet devices. Those
two-node links are most easily managed with Ethernet Bridging
(CONFIG_BRIDGE) instead of routing.
For more information see <http://www.linux-usb.org/usbnet/>.
To compile this driver as a module, choose M here: the
module will be called usbnet.
comment "USB Host-to-Host Cables"
depends on USB_USBNET
config USB_ALI_M5632
boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
depends on USB_USBNET
default y
help
Choose this option if you're using a host-to-host cable
based on this design, which supports USB 2.0 high speed.
config USB_AN2720
boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
depends on USB_USBNET
default y
help
Choose this option if you're using a host-to-host cable
based on this design. Note that AnchorChips is now a
Cypress brand.
config USB_BELKIN
boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
depends on USB_USBNET
default y
help
Choose this option if you're using a host-to-host cable
based on this design: two NetChip 2890 chips and an Atmel
microcontroller, with LEDs that indicate traffic.
config USB_GENESYS
boolean "GeneSys GL620USB-A based cables"
default y
depends on USB_USBNET
help
Choose this option if you're using a host-to-host cable,
or PC2PC motherboard, with this chip.
Note that the half-duplex "GL620USB" is not supported.
config USB_NET1080
boolean "NetChip 1080 based cables (Laplink, ...)"
default y
depends on USB_USBNET
help
Choose this option if you're using a host-to-host cable based
on this design: one NetChip 1080 chips and supporting logic,
supporting LEDs that indicate traffic
config USB_PL2301
boolean "Prolific PL-2301/2302 based cables"
default y
# handshake/init/reset problems, from original 'plusb' driver
depends on USB_USBNET && EXPERIMENTAL
help
Choose this option if you're using a host-to-host cable
with one of these chips.
config USB_KC2190
boolean "KT Technology KC2190 based cables (InstaNet)"
default y
depends on USB_USBNET && EXPERIMENTAL
help
Choose this option if you're using a host-to-host cable
with one of these chips.
comment "Intelligent USB Devices/Gadgets"
depends on USB_USBNET
config USB_ARMLINUX
boolean "Embedded ARM Linux links (iPaq, ...)"
depends on USB_USBNET
default y
help
Choose this option to support the "usb-eth" networking driver
used by most of the ARM Linux community with device controllers
such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
in some PXA versions of the "blob" boot loader.
Linux-based "Gumstix" PXA-25x based systems use this protocol
to talk with other Linux systems.
Although the ROMs shipped with Sharp Zaurus products use a
different link level framing protocol, you can have them use
this simpler protocol by installing a different kernel.
config USB_EPSON2888
boolean "Epson 2888 based firmware (DEVELOPMENT)"
depends on USB_USBNET
default y
help
Choose this option to support the usb networking links used
by some sample firmware from Epson.
config USB_ZAURUS
boolean "Sharp Zaurus (stock ROMs)"
depends on USB_USBNET
select CRC32
default y
help
Choose this option to support the usb networking links used by
Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
If you install an alternate ROM image, you may no longer need
to support this protocol. Only the "eth-fd" driver really needs
this non-conformant variant of CDC Ethernet protocol.
config USB_CDCETHER
boolean "CDC Ethernet support (smart devices such as cable modems)"
depends on USB_USBNET
default y
help
This option supports devices conforming to the Communication Device
Class (CDC) Ethernet Control Model, a specification that's easy to
implement in device firmware. The CDC specifications are available
from <http://www.usb.org/>.
CDC Ethernet is an implementation option for DOCSIS cable modems
that support USB connectivity, used for non-Microsoft USB hosts.
This driver should work with at least the following devices:
* Ericsson PipeRider (all variants)
* Motorola (DM100 and SB4100)
* Broadcom Cable Modem (reference design)
* Toshiba PCX1100U
* ...
This driver creates an interface named "ethX", where X depends on
what other networking devices you have in use. However, if the
IEEE 802 "local assignment" bit is set in the address, a "usbX"
name is used instead.
comment "USB Network Adapters"
depends on USB_USBNET
config USB_AX8817X
boolean "ASIX AX88xxx Based USB 2.0 Ethernet Devices"
depends on USB_USBNET && NET_ETHERNET
select CRC32
select MII
default y
help
This option adds support for ASIX AX88xxx based USB 2.0
10/100 Ethernet devices.
This driver should work with at least the following devices:
* Aten UC210T
* ASIX AX88172
* Billionton Systems, USB2AR
* Buffalo LUA-U2-KTX
* Corega FEther USB2-TX
* D-Link DUB-E100
* Hawking UF200
* Linksys USB200M
* Netgear FA120
* Sitecom LN-029
* Intellinet USB 2.0 Ethernet
* ST Lab USB 2.0 Ethernet
* TrendNet TU2-ET100
This driver creates an interface named "ethX", where X depends on
what other networking devices you have in use.
config USB_ZD1201
tristate "USB ZD1201 based Wireless device support"
depends on NET_RADIO
select FW_LOADER
---help---
Say Y if you want to use wireless LAN adapters based on the ZyDAS
ZD1201 chip.
This driver makes the adapter appear as a normal Ethernet interface,
typically on wlan0.
The zd1201 device requires external firmware to be loaded.
This can be found at http://linux-lc100020.sourceforge.net/
To compile this driver as a module, choose M here: the
module will be called zd1201.
endmenu