blob: f700c81a1321ca2de222b6f1561408e454094204 [file] [log] [blame]
/*
* P1022DS board specific routines
*
* Authors: Travis Wheatley <travis.wheatley@freescale.com>
* Dave Liu <daveliu@freescale.com>
* Timur Tabi <timur@freescale.com>
*
* Copyright 2010 Freescale Semiconductor, Inc.
*
* This file is taken from the Freescale P1022DS BSP, with modifications:
* 2) No AMP support
* 3) No PCI endpoint support
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
* kind, whether express or implied.
*/
#include <linux/pci.h>
#include <linux/of_platform.h>
#include <linux/memblock.h>
#include <asm/div64.h>
#include <asm/mpic.h>
#include <asm/swiotlb.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
#include <asm/udbg.h>
#include <asm/fsl_guts.h>
#include "smp.h"
#include "mpc85xx.h"
#if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
#define PMUXCR_ELBCDIU_MASK 0xc0000000
#define PMUXCR_ELBCDIU_NOR16 0x80000000
#define PMUXCR_ELBCDIU_DIU 0x40000000
/*
* Board-specific initialization of the DIU. This code should probably be
* executed when the DIU is opened, rather than in arch code, but the DIU
* driver does not have a mechanism for this (yet).
*
* This is especially problematic on the P1022DS because the local bus (eLBC)
* and the DIU video signals share the same pins, which means that enabling the
* DIU will disable access to NOR flash.
*/
/* DIU Pixel Clock bits of the CLKDVDR Global Utilities register */
#define CLKDVDR_PXCKEN 0x80000000
#define CLKDVDR_PXCKINV 0x10000000
#define CLKDVDR_PXCKDLY 0x06000000
#define CLKDVDR_PXCLK_MASK 0x00FF0000
/* Some ngPIXIS register definitions */
#define PX_CTL 3
#define PX_BRDCFG0 8
#define PX_BRDCFG1 9
#define PX_BRDCFG0_ELBC_SPI_MASK 0xc0
#define PX_BRDCFG0_ELBC_SPI_ELBC 0x00
#define PX_BRDCFG0_ELBC_SPI_NULL 0xc0
#define PX_BRDCFG0_ELBC_DIU 0x02
#define PX_BRDCFG1_DVIEN 0x80
#define PX_BRDCFG1_DFPEN 0x40
#define PX_BRDCFG1_BACKLIGHT 0x20
#define PX_BRDCFG1_DDCEN 0x10
#define PX_CTL_ALTACC 0x80
/*
* DIU Area Descriptor
*
* Note that we need to byte-swap the value before it's written to the AD
* register. So even though the registers don't look like they're in the same
* bit positions as they are on the MPC8610, the same value is written to the
* AD register on the MPC8610 and on the P1022.
*/
#define AD_BYTE_F 0x10000000
#define AD_ALPHA_C_MASK 0x0E000000
#define AD_ALPHA_C_SHIFT 25
#define AD_BLUE_C_MASK 0x01800000
#define AD_BLUE_C_SHIFT 23
#define AD_GREEN_C_MASK 0x00600000
#define AD_GREEN_C_SHIFT 21
#define AD_RED_C_MASK 0x00180000
#define AD_RED_C_SHIFT 19
#define AD_PALETTE 0x00040000
#define AD_PIXEL_S_MASK 0x00030000
#define AD_PIXEL_S_SHIFT 16
#define AD_COMP_3_MASK 0x0000F000
#define AD_COMP_3_SHIFT 12
#define AD_COMP_2_MASK 0x00000F00
#define AD_COMP_2_SHIFT 8
#define AD_COMP_1_MASK 0x000000F0
#define AD_COMP_1_SHIFT 4
#define AD_COMP_0_MASK 0x0000000F
#define AD_COMP_0_SHIFT 0
#define MAKE_AD(alpha, red, blue, green, size, c0, c1, c2, c3) \
cpu_to_le32(AD_BYTE_F | (alpha << AD_ALPHA_C_SHIFT) | \
(blue << AD_BLUE_C_SHIFT) | (green << AD_GREEN_C_SHIFT) | \
(red << AD_RED_C_SHIFT) | (c3 << AD_COMP_3_SHIFT) | \
(c2 << AD_COMP_2_SHIFT) | (c1 << AD_COMP_1_SHIFT) | \
(c0 << AD_COMP_0_SHIFT) | (size << AD_PIXEL_S_SHIFT))
/**
* p1022ds_get_pixel_format: return the Area Descriptor for a given pixel depth
*
* The Area Descriptor is a 32-bit value that determine which bits in each
* pixel are to be used for each color.
*/
static u32 p1022ds_get_pixel_format(enum fsl_diu_monitor_port port,
unsigned int bits_per_pixel)
{
switch (bits_per_pixel) {
case 32:
/* 0x88883316 */
return MAKE_AD(3, 2, 0, 1, 3, 8, 8, 8, 8);
case 24:
/* 0x88082219 */
return MAKE_AD(4, 0, 1, 2, 2, 0, 8, 8, 8);
case 16:
/* 0x65053118 */
return MAKE_AD(4, 2, 1, 0, 1, 5, 6, 5, 0);
default:
pr_err("fsl-diu: unsupported pixel depth %u\n", bits_per_pixel);
return 0;
}
}
/**
* p1022ds_set_gamma_table: update the gamma table, if necessary
*
* On some boards, the gamma table for some ports may need to be modified.
* This is not the case on the P1022DS, so we do nothing.
*/
static void p1022ds_set_gamma_table(enum fsl_diu_monitor_port port,
char *gamma_table_base)
{
}
/**
* p1022ds_set_monitor_port: switch the output to a different monitor port
*
*/
static void p1022ds_set_monitor_port(enum fsl_diu_monitor_port port)
{
struct device_node *guts_node;
struct device_node *indirect_node = NULL;
struct ccsr_guts __iomem *guts;
u8 __iomem *lbc_lcs0_ba = NULL;
u8 __iomem *lbc_lcs1_ba = NULL;
u8 b;
/* Map the global utilities registers. */
guts_node = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts");
if (!guts_node) {
pr_err("p1022ds: missing global utilties device node\n");
return;
}
guts = of_iomap(guts_node, 0);
if (!guts) {
pr_err("p1022ds: could not map global utilties device\n");
goto exit;
}
indirect_node = of_find_compatible_node(NULL, NULL,
"fsl,p1022ds-indirect-pixis");
if (!indirect_node) {
pr_err("p1022ds: missing pixis indirect mode node\n");
goto exit;
}
lbc_lcs0_ba = of_iomap(indirect_node, 0);
if (!lbc_lcs0_ba) {
pr_err("p1022ds: could not map localbus chip select 0\n");
goto exit;
}
lbc_lcs1_ba = of_iomap(indirect_node, 1);
if (!lbc_lcs1_ba) {
pr_err("p1022ds: could not map localbus chip select 1\n");
goto exit;
}
/* Make sure we're in indirect mode first. */
if ((in_be32(&guts->pmuxcr) & PMUXCR_ELBCDIU_MASK) !=
PMUXCR_ELBCDIU_DIU) {
struct device_node *pixis_node;
void __iomem *pixis;
pixis_node =
of_find_compatible_node(NULL, NULL, "fsl,p1022ds-fpga");
if (!pixis_node) {
pr_err("p1022ds: missing pixis node\n");
goto exit;
}
pixis = of_iomap(pixis_node, 0);
of_node_put(pixis_node);
if (!pixis) {
pr_err("p1022ds: could not map pixis registers\n");
goto exit;
}
/* Enable indirect PIXIS mode. */
setbits8(pixis + PX_CTL, PX_CTL_ALTACC);
iounmap(pixis);
/* Switch the board mux to the DIU */
out_8(lbc_lcs0_ba, PX_BRDCFG0); /* BRDCFG0 */
b = in_8(lbc_lcs1_ba);
b |= PX_BRDCFG0_ELBC_DIU;
out_8(lbc_lcs1_ba, b);
/* Set the chip mux to DIU mode. */
clrsetbits_be32(&guts->pmuxcr, PMUXCR_ELBCDIU_MASK,
PMUXCR_ELBCDIU_DIU);
in_be32(&guts->pmuxcr);
}
switch (port) {
case FSL_DIU_PORT_DVI:
/* Enable the DVI port, disable the DFP and the backlight */
out_8(lbc_lcs0_ba, PX_BRDCFG1);
b = in_8(lbc_lcs1_ba);
b &= ~(PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT);
b |= PX_BRDCFG1_DVIEN;
out_8(lbc_lcs1_ba, b);
break;
case FSL_DIU_PORT_LVDS:
/*
* LVDS also needs backlight enabled, otherwise the display
* will be blank.
*/
/* Enable the DFP port, disable the DVI and the backlight */
out_8(lbc_lcs0_ba, PX_BRDCFG1);
b = in_8(lbc_lcs1_ba);
b &= ~PX_BRDCFG1_DVIEN;
b |= PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT;
out_8(lbc_lcs1_ba, b);
break;
default:
pr_err("p1022ds: unsupported monitor port %i\n", port);
}
exit:
if (lbc_lcs1_ba)
iounmap(lbc_lcs1_ba);
if (lbc_lcs0_ba)
iounmap(lbc_lcs0_ba);
if (guts)
iounmap(guts);
of_node_put(indirect_node);
of_node_put(guts_node);
}
/**
* p1022ds_set_pixel_clock: program the DIU's clock
*
* @pixclock: the wavelength, in picoseconds, of the clock
*/
void p1022ds_set_pixel_clock(unsigned int pixclock)
{
struct device_node *guts_np = NULL;
struct ccsr_guts __iomem *guts;
unsigned long freq;
u64 temp;
u32 pxclk;
/* Map the global utilities registers. */
guts_np = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts");
if (!guts_np) {
pr_err("p1022ds: missing global utilties device node\n");
return;
}
guts = of_iomap(guts_np, 0);
of_node_put(guts_np);
if (!guts) {
pr_err("p1022ds: could not map global utilties device\n");
return;
}
/* Convert pixclock from a wavelength to a frequency */
temp = 1000000000000ULL;
do_div(temp, pixclock);
freq = temp;
/*
* 'pxclk' is the ratio of the platform clock to the pixel clock.
* This number is programmed into the CLKDVDR register, and the valid
* range of values is 2-255.
*/
pxclk = DIV_ROUND_CLOSEST(fsl_get_sys_freq(), freq);
pxclk = clamp_t(u32, pxclk, 2, 255);
/* Disable the pixel clock, and set it to non-inverted and no delay */
clrbits32(&guts->clkdvdr,
CLKDVDR_PXCKEN | CLKDVDR_PXCKDLY | CLKDVDR_PXCLK_MASK);
/* Enable the clock and set the pxclk */
setbits32(&guts->clkdvdr, CLKDVDR_PXCKEN | (pxclk << 16));
iounmap(guts);
}
/**
* p1022ds_valid_monitor_port: set the monitor port for sysfs
*/
enum fsl_diu_monitor_port
p1022ds_valid_monitor_port(enum fsl_diu_monitor_port port)
{
switch (port) {
case FSL_DIU_PORT_DVI:
case FSL_DIU_PORT_LVDS:
return port;
default:
return FSL_DIU_PORT_DVI; /* Dual-link LVDS is not supported */
}
}
#endif
void __init p1022_ds_pic_init(void)
{
struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
MPIC_SINGLE_DEST_CPU,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
mpic_init(mpic);
}
#if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
/*
* Disables a node in the device tree.
*
* This function is called before kmalloc() is available, so the 'new' object
* should be allocated in the global area. The easiest way is to do that is
* to allocate one static local variable for each call to this function.
*/
static void __init disable_one_node(struct device_node *np, struct property *new)
{
struct property *old;
old = of_find_property(np, new->name, NULL);
if (old)
prom_update_property(np, new, old);
else
prom_add_property(np, new);
}
/* TRUE if there is a "video=fslfb" command-line parameter. */
static bool fslfb;
/*
* Search for a "video=fslfb" command-line parameter, and set 'fslfb' to
* true if we find it.
*
* We need to use early_param() instead of __setup() because the normal
* __setup() gets called to late. However, early_param() gets called very
* early, before the device tree is unflattened, so all we can do now is set a
* global variable. Later on, p1022_ds_setup_arch() will use that variable
* to determine if we need to update the device tree.
*/
static int __init early_video_setup(char *options)
{
fslfb = (strncmp(options, "fslfb:", 6) == 0);
return 0;
}
early_param("video", early_video_setup);
#endif
/*
* Setup the architecture
*/
static void __init p1022_ds_setup_arch(void)
{
#ifdef CONFIG_PCI
struct device_node *np;
#endif
dma_addr_t max = 0xffffffff;
if (ppc_md.progress)
ppc_md.progress("p1022_ds_setup_arch()", 0);
#ifdef CONFIG_PCI
for_each_compatible_node(np, "pci", "fsl,p1022-pcie") {
struct resource rsrc;
struct pci_controller *hose;
of_address_to_resource(np, 0, &rsrc);
if ((rsrc.start & 0xfffff) == 0x8000)
fsl_add_bridge(np, 1);
else
fsl_add_bridge(np, 0);
hose = pci_find_hose_for_OF_device(np);
max = min(max, hose->dma_window_base_cur +
hose->dma_window_size);
}
#endif
#if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
diu_ops.get_pixel_format = p1022ds_get_pixel_format;
diu_ops.set_gamma_table = p1022ds_set_gamma_table;
diu_ops.set_monitor_port = p1022ds_set_monitor_port;
diu_ops.set_pixel_clock = p1022ds_set_pixel_clock;
diu_ops.valid_monitor_port = p1022ds_valid_monitor_port;
/*
* Disable the NOR flash node if there is video=fslfb... command-line
* parameter. When the DIU is active, NOR flash is unavailable, so we
* have to disable the node before the MTD driver loads.
*/
if (fslfb) {
struct device_node *np =
of_find_compatible_node(NULL, NULL, "fsl,p1022-elbc");
if (np) {
np = of_find_compatible_node(np, NULL, "cfi-flash");
if (np) {
static struct property nor_status = {
.name = "status",
.value = "disabled",
.length = sizeof("disabled"),
};
pr_info("p1022ds: disabling %s node",
np->full_name);
disable_one_node(np, &nor_status);
of_node_put(np);
}
}
}
#endif
mpc85xx_smp_init();
#ifdef CONFIG_SWIOTLB
if (memblock_end_of_DRAM() > max) {
ppc_swiotlb_enable = 1;
set_pci_dma_ops(&swiotlb_dma_ops);
ppc_md.pci_dma_dev_setup = pci_dma_dev_setup_swiotlb;
}
#endif
pr_info("Freescale P1022 DS reference board\n");
}
machine_device_initcall(p1022_ds, mpc85xx_common_publish_devices);
machine_arch_initcall(p1022_ds, swiotlb_setup_bus_notifier);
/*
* Called very early, device-tree isn't unflattened
*/
static int __init p1022_ds_probe(void)
{
unsigned long root = of_get_flat_dt_root();
return of_flat_dt_is_compatible(root, "fsl,p1022ds");
}
define_machine(p1022_ds) {
.name = "P1022 DS",
.probe = p1022_ds_probe,
.setup_arch = p1022_ds_setup_arch,
.init_IRQ = p1022_ds_pic_init,
#ifdef CONFIG_PCI
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
.get_irq = mpic_get_irq,
.restart = fsl_rstcr_restart,
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
};