| /* |
| * |
| * arch/arm/mach-u300/include/mach/syscon.h |
| * |
| * |
| * Copyright (C) 2008 ST-Ericsson AB |
| * |
| * Author: Rickard Andersson <rickard.andersson@stericsson.com> |
| */ |
| |
| #ifndef __MACH_SYSCON_H |
| #define __MACH_SYSCON_H |
| |
| /* |
| * All register defines for SYSCON registers that concerns individual |
| * block clocks and reset lines are registered here. This is because |
| * we don't want any other file to try to fool around with this stuff. |
| */ |
| |
| /* APP side SYSCON registers */ |
| /* TODO: this is incomplete. Add all from asic_syscon_map.h eventually. */ |
| /* CLK Control Register 16bit (R/W) */ |
| #define U300_SYSCON_CCR (0x0000) |
| #define U300_SYSCON_CCR_I2S1_USE_VCXO (0x0040) |
| #define U300_SYSCON_CCR_I2S0_USE_VCXO (0x0020) |
| #define U300_SYSCON_CCR_TURN_VCXO_ON (0x0008) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK (0x0007) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER (0x04) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW (0x03) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE (0x02) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH (0x01) |
| #define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST (0x00) |
| /* CLK Status Register 16bit (R/W) */ |
| #define U300_SYSCON_CSR (0x0004) |
| #define U300_SYSCON_CSR_PLL208_LOCK_IND (0x0002) |
| #define U300_SYSCON_CSR_PLL13_LOCK_IND (0x0001) |
| /* Reset lines for SLOW devices 16bit (R/W) */ |
| #define U300_SYSCON_RSR (0x0014) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_RSR_PPM_RESET_EN (0x0200) |
| #endif |
| #define U300_SYSCON_RSR_ACC_TMR_RESET_EN (0x0100) |
| #define U300_SYSCON_RSR_APP_TMR_RESET_EN (0x0080) |
| #define U300_SYSCON_RSR_RTC_RESET_EN (0x0040) |
| #define U300_SYSCON_RSR_KEYPAD_RESET_EN (0x0020) |
| #define U300_SYSCON_RSR_GPIO_RESET_EN (0x0010) |
| #define U300_SYSCON_RSR_EH_RESET_EN (0x0008) |
| #define U300_SYSCON_RSR_BTR_RESET_EN (0x0004) |
| #define U300_SYSCON_RSR_UART_RESET_EN (0x0002) |
| #define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN (0x0001) |
| /* Reset lines for FAST devices 16bit (R/W) */ |
| #define U300_SYSCON_RFR (0x0018) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_RFR_UART1_RESET_ENABLE (0x0080) |
| #endif |
| #define U300_SYSCON_RFR_SPI_RESET_ENABLE (0x0040) |
| #define U300_SYSCON_RFR_MMC_RESET_ENABLE (0x0020) |
| #define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE (0x0010) |
| #define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE (0x0008) |
| #define U300_SYSCON_RFR_I2C1_RESET_ENABLE (0x0004) |
| #define U300_SYSCON_RFR_I2C0_RESET_ENABLE (0x0002) |
| #define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE (0x0001) |
| /* Reset lines for the rest of the peripherals 16bit (R/W) */ |
| #define U300_SYSCON_RRR (0x001c) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_RRR_CDS_RESET_EN (0x4000) |
| #define U300_SYSCON_RRR_ISP_RESET_EN (0x2000) |
| #endif |
| #define U300_SYSCON_RRR_INTCON_RESET_EN (0x1000) |
| #define U300_SYSCON_RRR_MSPRO_RESET_EN (0x0800) |
| #define U300_SYSCON_RRR_XGAM_RESET_EN (0x0100) |
| #define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN (0x0080) |
| #define U300_SYSCON_RRR_NANDIF_RESET_EN (0x0040) |
| #define U300_SYSCON_RRR_EMIF_RESET_EN (0x0020) |
| #define U300_SYSCON_RRR_DMAC_RESET_EN (0x0010) |
| #define U300_SYSCON_RRR_CPU_RESET_EN (0x0008) |
| #define U300_SYSCON_RRR_APEX_RESET_EN (0x0004) |
| #define U300_SYSCON_RRR_AHB_RESET_EN (0x0002) |
| #define U300_SYSCON_RRR_AAIF_RESET_EN (0x0001) |
| /* Clock enable for SLOW peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CESR (0x0020) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_CESR_PPM_CLK_EN (0x0200) |
| #endif |
| #define U300_SYSCON_CESR_ACC_TMR_CLK_EN (0x0100) |
| #define U300_SYSCON_CESR_APP_TMR_CLK_EN (0x0080) |
| #define U300_SYSCON_CESR_KEYPAD_CLK_EN (0x0040) |
| #define U300_SYSCON_CESR_GPIO_CLK_EN (0x0010) |
| #define U300_SYSCON_CESR_EH_CLK_EN (0x0008) |
| #define U300_SYSCON_CESR_BTR_CLK_EN (0x0004) |
| #define U300_SYSCON_CESR_UART_CLK_EN (0x0002) |
| #define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN (0x0001) |
| /* Clock enable for FAST peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CEFR (0x0024) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_CEFR_UART1_CLK_EN (0x0200) |
| #endif |
| #define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN (0x0100) |
| #define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN (0x0080) |
| #define U300_SYSCON_CEFR_SPI_CLK_EN (0x0040) |
| #define U300_SYSCON_CEFR_MMC_CLK_EN (0x0020) |
| #define U300_SYSCON_CEFR_I2S1_CLK_EN (0x0010) |
| #define U300_SYSCON_CEFR_I2S0_CLK_EN (0x0008) |
| #define U300_SYSCON_CEFR_I2C1_CLK_EN (0x0004) |
| #define U300_SYSCON_CEFR_I2C0_CLK_EN (0x0002) |
| #define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN (0x0001) |
| /* Clock enable for the rest of the peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CERR (0x0028) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_CERR_CDS_CLK_EN (0x2000) |
| #define U300_SYSCON_CERR_ISP_CLK_EN (0x1000) |
| #endif |
| #define U300_SYSCON_CERR_MSPRO_CLK_EN (0x0800) |
| #define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN (0x0400) |
| #define U300_SYSCON_CERR_SEMI_CLK_EN (0x0200) |
| #define U300_SYSCON_CERR_XGAM_CLK_EN (0x0100) |
| #define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN (0x0080) |
| #define U300_SYSCON_CERR_NANDIF_CLK_EN (0x0040) |
| #define U300_SYSCON_CERR_EMIF_CLK_EN (0x0020) |
| #define U300_SYSCON_CERR_DMAC_CLK_EN (0x0010) |
| #define U300_SYSCON_CERR_CPU_CLK_EN (0x0008) |
| #define U300_SYSCON_CERR_APEX_CLK_EN (0x0004) |
| #define U300_SYSCON_CERR_AHB_CLK_EN (0x0002) |
| #define U300_SYSCON_CERR_AAIF_CLK_EN (0x0001) |
| /* Single block clock enable 16bit (-/W) */ |
| #define U300_SYSCON_SBCER (0x002c) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_SBCER_PPM_CLK_EN (0x0009) |
| #endif |
| #define U300_SYSCON_SBCER_ACC_TMR_CLK_EN (0x0008) |
| #define U300_SYSCON_SBCER_APP_TMR_CLK_EN (0x0007) |
| #define U300_SYSCON_SBCER_KEYPAD_CLK_EN (0x0006) |
| #define U300_SYSCON_SBCER_GPIO_CLK_EN (0x0004) |
| #define U300_SYSCON_SBCER_EH_CLK_EN (0x0003) |
| #define U300_SYSCON_SBCER_BTR_CLK_EN (0x0002) |
| #define U300_SYSCON_SBCER_UART_CLK_EN (0x0001) |
| #define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN (0x0000) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_SBCER_UART1_CLK_EN (0x0019) |
| #endif |
| #define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN (0x0018) |
| #define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN (0x0017) |
| #define U300_SYSCON_SBCER_SPI_CLK_EN (0x0016) |
| #define U300_SYSCON_SBCER_MMC_CLK_EN (0x0015) |
| #define U300_SYSCON_SBCER_I2S1_CLK_EN (0x0014) |
| #define U300_SYSCON_SBCER_I2S0_CLK_EN (0x0013) |
| #define U300_SYSCON_SBCER_I2C1_CLK_EN (0x0012) |
| #define U300_SYSCON_SBCER_I2C0_CLK_EN (0x0011) |
| #define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN (0x0010) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_SBCER_CDS_CLK_EN (0x002D) |
| #define U300_SYSCON_SBCER_ISP_CLK_EN (0x002C) |
| #endif |
| #define U300_SYSCON_SBCER_MSPRO_CLK_EN (0x002B) |
| #define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN (0x002A) |
| #define U300_SYSCON_SBCER_SEMI_CLK_EN (0x0029) |
| #define U300_SYSCON_SBCER_XGAM_CLK_EN (0x0028) |
| #define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN (0x0027) |
| #define U300_SYSCON_SBCER_NANDIF_CLK_EN (0x0026) |
| #define U300_SYSCON_SBCER_EMIF_CLK_EN (0x0025) |
| #define U300_SYSCON_SBCER_DMAC_CLK_EN (0x0024) |
| #define U300_SYSCON_SBCER_CPU_CLK_EN (0x0023) |
| #define U300_SYSCON_SBCER_APEX_CLK_EN (0x0022) |
| #define U300_SYSCON_SBCER_AHB_CLK_EN (0x0021) |
| #define U300_SYSCON_SBCER_AAIF_CLK_EN (0x0020) |
| /* Single block clock disable 16bit (-/W) */ |
| #define U300_SYSCON_SBCDR (0x0030) |
| /* Same values as above for SBCER */ |
| /* Clock force SLOW peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CFSR (0x003c) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN (0x0200) |
| #endif |
| #define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN (0x0100) |
| #define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN (0x0080) |
| #define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN (0x0020) |
| #define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN (0x0010) |
| #define U300_SYSCON_CFSR_EH_CLK_FORCE_EN (0x0008) |
| #define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN (0x0004) |
| #define U300_SYSCON_CFSR_UART_CLK_FORCE_EN (0x0002) |
| #define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN (0x0001) |
| /* Clock force FAST peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CFFR (0x40) |
| /* Values not defined. Define if you want to use them. */ |
| /* Clock force the rest of the peripherals 16bit (R/W) */ |
| #define U300_SYSCON_CFRR (0x44) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN (0x2000) |
| #define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN (0x1000) |
| #endif |
| #define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN (0x0800) |
| #define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN (0x0400) |
| #define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN (0x0200) |
| #define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN (0x0100) |
| #define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN (0x0080) |
| #define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN (0x0040) |
| #define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN (0x0020) |
| #define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN (0x0010) |
| #define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN (0x0008) |
| #define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN (0x0004) |
| #define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN (0x0002) |
| #define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN (0x0001) |
| /* PLL208 Frequency Control 16bit (R/W) */ |
| #define U300_SYSCON_PFCR (0x48) |
| #define U300_SYSCON_PFCR_DPLL_MULT_NUM (0x000F) |
| /* Power Management Control 16bit (R/W) */ |
| #define U300_SYSCON_PMCR (0x50) |
| #define U300_SYSCON_PMCR_DCON_ENABLE (0x0002) |
| #define U300_SYSCON_PMCR_PWR_MGNT_ENABLE (0x0001) |
| /* |
| * All other clocking registers moved to clock.c! |
| */ |
| /* Reset Out 16bit (R/W) */ |
| #define U300_SYSCON_RCR (0x6c) |
| #define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE (0x0001) |
| /* EMIF Slew Rate Control 16bit (R/W) */ |
| #define U300_SYSCON_SRCLR (0x70) |
| #define U300_SYSCON_SRCLR_MASK (0x03FF) |
| #define U300_SYSCON_SRCLR_VALUE (0x03FF) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B (0x0200) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A (0x0100) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B (0x0080) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A (0x0040) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B (0x0020) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A (0x0010) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B (0x0008) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A (0x0004) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B (0x0002) |
| #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A (0x0001) |
| /* EMIF Clock Control Register 16bit (R/W) */ |
| #define U300_SYSCON_ECCR (0x0078) |
| #define U300_SYSCON_ECCR_MASK (0x000F) |
| #define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE (0x0008) |
| #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004) |
| #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002) |
| #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001) |
| /* PAD MUX Control register 1 (LOW) 16bit (R/W) */ |
| #define U300_SYSCON_PMC1LR (0x007C) |
| #define U300_SYSCON_PMC1LR_MASK (0xFFFF) |
| #define U300_SYSCON_PMC1LR_CDI_MASK (0xC000) |
| #define U300_SYSCON_PMC1LR_CDI_CDI (0x0000) |
| #define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000) |
| #ifdef CONFIG_MACH_U300_BS335 |
| #define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000) |
| #define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000) |
| #elif CONFIG_MACH_U300_BS365 |
| #define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000) |
| #define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000) |
| #endif |
| #define U300_SYSCON_PMC1LR_PDI_MASK (0x3000) |
| #define U300_SYSCON_PMC1LR_PDI_PDI (0x0000) |
| #define U300_SYSCON_PMC1LR_PDI_EGG (0x1000) |
| #define U300_SYSCON_PMC1LR_PDI_WCDMA (0x3000) |
| #define U300_SYSCON_PMC1LR_MMCSD_MASK (0x0C00) |
| #define U300_SYSCON_PMC1LR_MMCSD_MMCSD (0x0000) |
| #define U300_SYSCON_PMC1LR_MMCSD_MSPRO (0x0400) |
| #define U300_SYSCON_PMC1LR_MMCSD_DSP (0x0800) |
| #define U300_SYSCON_PMC1LR_MMCSD_WCDMA (0x0C00) |
| #define U300_SYSCON_PMC1LR_ETM_MASK (0x0300) |
| #define U300_SYSCON_PMC1LR_ETM_ACC (0x0000) |
| #define U300_SYSCON_PMC1LR_ETM_APP (0x0100) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK (0x00C0) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC (0x0000) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF (0x0040) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM (0x0080) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB (0x00C0) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK (0x0030) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC (0x0000) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF (0x0010) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM (0x0020) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI (0x0030) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK (0x000C) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC (0x0000) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF (0x0004) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM (0x0008) |
| #define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI (0x000C) |
| #define U300_SYSCON_PMC1LR_EMIF_1_MASK (0x0003) |
| #define U300_SYSCON_PMC1LR_EMIF_1_STATIC (0x0000) |
| #define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 (0x0001) |
| #define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 (0x0002) |
| #define U300_SYSCON_PMC1LR_EMIF_1 (0x0003) |
| /* PAD MUX Control register 2 (HIGH) 16bit (R/W) */ |
| #define U300_SYSCON_PMC1HR (0x007E) |
| #define U300_SYSCON_PMC1HR_MASK (0xFFFF) |
| #define U300_SYSCON_PMC1HR_MISC_2_MASK (0xC000) |
| #define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_MISC_2_MSPRO (0x4000) |
| #define U300_SYSCON_PMC1HR_MISC_2_DSP (0x8000) |
| #define U300_SYSCON_PMC1HR_MISC_2_AAIF (0xC000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK (0x3000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF (0x1000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP (0x2000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF (0x3000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK (0x0C00) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC (0x0400) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP (0x0800) |
| #define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF (0x0C00) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK (0x0300) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI (0x0100) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF (0x0300) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK (0x00C0) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI (0x0040) |
| #define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF (0x00C0) |
| #define U300_SYSCON_PMC1HR_APP_SPI_2_MASK (0x0030) |
| #define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_SPI_2_SPI (0x0010) |
| #define U300_SYSCON_PMC1HR_APP_SPI_2_DSP (0x0020) |
| #define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF (0x0030) |
| #define U300_SYSCON_PMC1HR_APP_UART0_2_MASK (0x000C) |
| #define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 (0x0004) |
| #define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS (0x0008) |
| #define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF (0x000C) |
| #define U300_SYSCON_PMC1HR_APP_UART0_1_MASK (0x0003) |
| #define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 (0x0001) |
| #define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF (0x0003) |
| /* Step one for killing the applications system 16bit (-/W) */ |
| #define U300_SYSCON_KA1R (0x0080) |
| #define U300_SYSCON_KA1R_MASK (0xFFFF) |
| #define U300_SYSCON_KA1R_VALUE (0xFFFF) |
| /* Step two for killing the application system 16bit (-/W) */ |
| #define U300_SYSCON_KA2R (0x0084) |
| #define U300_SYSCON_KA2R_MASK (0xFFFF) |
| #define U300_SYSCON_KA2R_VALUE (0xFFFF) |
| /* MMC/MSPRO frequency divider register 0 16bit (R/W) */ |
| #define U300_SYSCON_MMF0R (0x90) |
| #define U300_SYSCON_MMF0R_MASK (0x00FF) |
| #define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK (0x00F0) |
| #define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK (0x000F) |
| /* MMC/MSPRO frequency divider register 1 16bit (R/W) */ |
| #define U300_SYSCON_MMF1R (0x94) |
| #define U300_SYSCON_MMF1R_MASK (0x00FF) |
| #define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK (0x00F0) |
| #define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK (0x000F) |
| /* AAIF control register 16 bit (R/W) */ |
| #define U300_SYSCON_AAIFCR (0x98) |
| #define U300_SYSCON_AAIFCR_MASK (0x0003) |
| #define U300_SYSCON_AAIFCR_AASW_CTRL_MASK (0x0003) |
| #define U300_SYSCON_AAIFCR_AASW_CTRL_FUNCTIONAL (0x0000) |
| #define U300_SYSCON_AAIFCR_AASW_CTRL_MONITORING (0x0001) |
| #define U300_SYSCON_AAIFCR_AASW_CTRL_ACC_TO_EXT (0x0002) |
| #define U300_SYSCON_AAIFCR_AASW_CTRL_APP_TO_EXT (0x0003) |
| /* Clock control for the MMC and MSPRO blocks 16bit (R/W) */ |
| #define U300_SYSCON_MMCR (0x9C) |
| #define U300_SYSCON_MMCR_MASK (0x0003) |
| #define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002) |
| #define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001) |
| /* Pull up/down control (R/W) */ |
| #define U300_SYSCON_PUCR (0x104) |
| #define U300_SYSCON_PUCR_EMIF_1_WAIT_N_PU_ENABLE (0x0200) |
| #define U300_SYSCON_PUCR_EMIF_1_NFIF_READY_PU_ENABLE (0x0100) |
| #define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE (0x0080) |
| #define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE (0x0040) |
| #define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK (0x003F) |
| /* Padmux 2 control */ |
| #define U300_SYSCON_PMC2R (0x100) |
| #define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0) |
| #define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040) |
| #define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080) |
| #define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0) |
| #define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300) |
| #define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100) |
| #define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200) |
| #define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300) |
| #define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00) |
| #define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400) |
| #define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800) |
| #define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00) |
| #define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000) |
| #define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000) |
| #define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000) |
| #define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000) |
| #define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000) |
| #define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000) |
| #define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000) |
| #define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000) |
| /* TODO: More SYSCON registers missing */ |
| #define U300_SYSCON_PMC3R (0x10c) |
| #define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000) |
| #define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000) |
| #define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000) |
| #define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000) |
| /* TODO: Missing other configs */ |
| #define U300_SYSCON_PMC4R (0x168) |
| #define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003) |
| #define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000) |
| #define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C) |
| #define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000) |
| #define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004) |
| #define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008) |
| #define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C) |
| #define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030) |
| #define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000) |
| #define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010) |
| #define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020) |
| #define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030) |
| #define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300) |
| #define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000) |
| #define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100) |
| #define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200) |
| /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */ |
| #define U300_SYSCON_S0CCR (0x120) |
| #define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF) |
| #define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000) |
| #define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000) |
| #define U300_SYSCON_S0CCR_CLOCK_INV (0x0200) |
| #define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0) |
| #define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E) |
| #define U300_SYSCON_S0CCR_CLOCK_ENABLE (0x0001) |
| #define U300_SYSCON_S0CCR_SEL_MCLK (0x8<<1) |
| #define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK (0xA<<1) |
| #define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK (0xC<<1) |
| #define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK (0xD<<1) |
| #define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK (0xE<<1) |
| #define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK (0x0<<1) |
| #define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK (0x2<<1) |
| #define U300_SYSCON_S0CCR_SEL_RTC_CLK (0x4<<1) |
| #define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK (0x6<<1) |
| /* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */ |
| #define U300_SYSCON_S1CCR (0x124) |
| #define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF) |
| #define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000) |
| #define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000) |
| #define U300_SYSCON_S1CCR_CLOCK_INV (0x0200) |
| #define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0) |
| #define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E) |
| #define U300_SYSCON_S1CCR_CLOCK_ENABLE (0x0001) |
| #define U300_SYSCON_S1CCR_SEL_MCLK (0x8<<1) |
| #define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK (0xA<<1) |
| #define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK (0xC<<1) |
| #define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK (0xD<<1) |
| #define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK (0xE<<1) |
| #define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK (0x0<<1) |
| #define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK (0x2<<1) |
| #define U300_SYSCON_S1CCR_SEL_RTC_CLK (0x4<<1) |
| #define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK (0x6<<1) |
| /* SYS_2_CLK_CONTROL third clock contol 16 bit (R/W) */ |
| #define U300_SYSCON_S2CCR (0x128) |
| #define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF) |
| #define U300_SYSCON_S2CCR_CLK_STEAL (0x8000) |
| #define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000) |
| #define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000) |
| #define U300_SYSCON_S2CCR_CLOCK_INV (0x0200) |
| #define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0) |
| #define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E) |
| #define U300_SYSCON_S2CCR_CLOCK_ENABLE (0x0001) |
| #define U300_SYSCON_S2CCR_SEL_MCLK (0x8<<1) |
| #define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK (0xA<<1) |
| #define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK (0xC<<1) |
| #define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK (0xD<<1) |
| #define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK (0xE<<1) |
| #define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK (0x0<<1) |
| #define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK (0x2<<1) |
| #define U300_SYSCON_S2CCR_SEL_RTC_CLK (0x4<<1) |
| #define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK (0x6<<1) |
| /* SYS_MISC_CONTROL, miscellaneous 16bit (R/W) */ |
| #define U300_SYSCON_MCR (0x12c) |
| #define U300_SYSCON_MCR_FIELD_MASK (0x00FF) |
| #define U300_SYSCON_MCR_PMGEN_CR_4_MASK (0x00C0) |
| #define U300_SYSCON_MCR_PMGEN_CR_4_GPIO (0x0000) |
| #define U300_SYSCON_MCR_PMGEN_CR_4_SPI (0x0040) |
| #define U300_SYSCON_MCR_PMGEN_CR_4_AAIF (0x00C0) |
| #define U300_SYSCON_MCR_PMGEN_CR_2_MASK (0x0030) |
| #define U300_SYSCON_MCR_PMGEN_CR_2_GPIO (0x0000) |
| #define U300_SYSCON_MCR_PMGEN_CR_2_EMIF_1_STATIC (0x0010) |
| #define U300_SYSCON_MCR_PMGEN_CR_2_DSP (0x0020) |
| #define U300_SYSCON_MCR_PMGEN_CR_2_AAIF (0x0030) |
| #define U300_SYSCON_MCR_PMGEN_CR_0_MASK (0x000C) |
| #define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_1_SDRAM_M1 (0x0000) |
| #define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_1_SDRAM_M2 (0x0004) |
| #define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_1_SDRAM_M3 (0x0008) |
| #define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_0_SDRAM (0x000C) |
| #define U300_SYSCON_MCR_PM1G_MODE_ENABLE (0x0002) |
| #define U300_SYSCON_MCR_PMTG5_MODE_ENABLE (0x0001) |
| /* SC_PLL_IRQ_CONTROL 16bit (R/W) */ |
| #define U300_SYSCON_PICR (0x0130) |
| #define U300_SYSCON_PICR_MASK (0x00FF) |
| #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080) |
| #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040) |
| #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020) |
| #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010) |
| #define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008) |
| #define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004) |
| #define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002) |
| #define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001) |
| /* SC_PLL_IRQ_STATUS 16 bit (R/-) */ |
| #define U300_SYSCON_PISR (0x0134) |
| #define U300_SYSCON_PISR_MASK (0x000F) |
| #define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008) |
| #define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004) |
| #define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002) |
| #define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001) |
| /* SC_PLL_IRQ_CLEAR 16 bit (-/W) */ |
| #define U300_SYSCON_PICLR (0x0138) |
| #define U300_SYSCON_PICLR_MASK (0x000F) |
| #define U300_SYSCON_PICLR_RWMASK (0x0000) |
| #define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008) |
| #define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004) |
| #define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002) |
| #define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001) |
| /* CAMIF_CONTROL 16 bit (-/W) */ |
| #define U300_SYSCON_CICR (0x013C) |
| #define U300_SYSCON_CICR_MASK (0x0FFF) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_MASK (0x0F00) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT1 (0x0C00) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT0 (0x0300) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_MASK (0x00F0) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT1 (0x00C0) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT0 (0x0030) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_MASK (0x000F) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT1 (0x000C) |
| #define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT0 (0x0003) |
| /* Clock activity observability register 0 */ |
| #define U300_SYSCON_C0OAR (0x140) |
| #define U300_SYSCON_C0OAR_MASK (0xFFFF) |
| #define U300_SYSCON_C0OAR_VALUE (0xFFFF) |
| #define U300_SYSCON_C0OAR_BT_H_CLK (0x8000) |
| #define U300_SYSCON_C0OAR_ASPB_P_CLK (0x4000) |
| #define U300_SYSCON_C0OAR_APP_SEMI_H_CLK (0x2000) |
| #define U300_SYSCON_C0OAR_APP_SEMI_CLK (0x1000) |
| #define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK (0x0800) |
| #define U300_SYSCON_C0OAR_APP_I2S1_CLK (0x0400) |
| #define U300_SYSCON_C0OAR_APP_I2S0_CLK (0x0200) |
| #define U300_SYSCON_C0OAR_APP_CPU_CLK (0x0100) |
| #define U300_SYSCON_C0OAR_APP_52_CLK (0x0080) |
| #define U300_SYSCON_C0OAR_APP_208_CLK (0x0040) |
| #define U300_SYSCON_C0OAR_APP_104_CLK (0x0020) |
| #define U300_SYSCON_C0OAR_APEX_CLK (0x0010) |
| #define U300_SYSCON_C0OAR_AHPB_M_H_CLK (0x0008) |
| #define U300_SYSCON_C0OAR_AHB_CLK (0x0004) |
| #define U300_SYSCON_C0OAR_AFPB_P_CLK (0x0002) |
| #define U300_SYSCON_C0OAR_AAIF_CLK (0x0001) |
| /* Clock activity observability register 1 */ |
| #define U300_SYSCON_C1OAR (0x144) |
| #define U300_SYSCON_C1OAR_MASK (0x3FFE) |
| #define U300_SYSCON_C1OAR_VALUE (0x3FFE) |
| #define U300_SYSCON_C1OAR_NFIF_F_CLK (0x2000) |
| #define U300_SYSCON_C1OAR_MSPRO_CLK (0x1000) |
| #define U300_SYSCON_C1OAR_MMC_P_CLK (0x0800) |
| #define U300_SYSCON_C1OAR_MMC_CLK (0x0400) |
| #define U300_SYSCON_C1OAR_KP_P_CLK (0x0200) |
| #define U300_SYSCON_C1OAR_I2C1_P_CLK (0x0100) |
| #define U300_SYSCON_C1OAR_I2C0_P_CLK (0x0080) |
| #define U300_SYSCON_C1OAR_GPIO_CLK (0x0040) |
| #define U300_SYSCON_C1OAR_EMIF_MPMC_CLK (0x0020) |
| #define U300_SYSCON_C1OAR_EMIF_H_CLK (0x0010) |
| #define U300_SYSCON_C1OAR_EVHIST_CLK (0x0008) |
| #define U300_SYSCON_C1OAR_PPM_CLK (0x0004) |
| #define U300_SYSCON_C1OAR_DMA_CLK (0x0002) |
| /* Clock activity observability register 2 */ |
| #define U300_SYSCON_C2OAR (0x148) |
| #define U300_SYSCON_C2OAR_MASK (0x0FFF) |
| #define U300_SYSCON_C2OAR_VALUE (0x0FFF) |
| #define U300_SYSCON_C2OAR_XGAM_CDI_CLK (0x0800) |
| #define U300_SYSCON_C2OAR_XGAM_CLK (0x0400) |
| #define U300_SYSCON_C2OAR_VC_H_CLK (0x0200) |
| #define U300_SYSCON_C2OAR_VC_CLK (0x0100) |
| #define U300_SYSCON_C2OAR_UA_P_CLK (0x0080) |
| #define U300_SYSCON_C2OAR_TMR1_CLK (0x0040) |
| #define U300_SYSCON_C2OAR_TMR0_CLK (0x0020) |
| #define U300_SYSCON_C2OAR_SPI_P_CLK (0x0010) |
| #define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK (0x0008) |
| #define U300_SYSCON_C2OAR_PCM_I2S1_CLK (0x0004) |
| #define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK (0x0002) |
| #define U300_SYSCON_C2OAR_PCM_I2S0_CLK (0x0001) |
| |
| /* Chip ID register 16bit (R/-) */ |
| #define U300_SYSCON_CIDR (0x400) |
| /* Video IRQ clear 16bit (R/W) */ |
| #define U300_SYSCON_VICR (0x404) |
| #define U300_SYSCON_VICR_VIDEO1_IRQ_CLEAR_ENABLE (0x0002) |
| #define U300_SYSCON_VICR_VIDEO0_IRQ_CLEAR_ENABLE (0x0001) |
| /* SMCR */ |
| #define U300_SYSCON_SMCR (0x4d0) |
| #define U300_SYSCON_SMCR_FIELD_MASK (0x000e) |
| #define U300_SYSCON_SMCR_SEMI_SREFACK_IND (0x0008) |
| #define U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE (0x0004) |
| #define U300_SYSCON_SMCR_SEMI_EXT_BOOT_MODE_ENABLE (0x0002) |
| /* CPU_SW_DBGEN Software Debug Enable 16bit (R/W) */ |
| #define U300_SYSCON_CSDR (0x4f0) |
| #define U300_SYSCON_CSDR_SW_DEBUG_ENABLE (0x0001) |
| /* PRINT_CONTROL Print Control 16bit (R/-) */ |
| #define U300_SYSCON_PCR (0x4f8) |
| #define U300_SYSCON_PCR_SERV_IND (0x0001) |
| /* BOOT_CONTROL 16bit (R/-) */ |
| #define U300_SYSCON_BCR (0x4fc) |
| #define U300_SYSCON_BCR_ACC_CPU_SUBSYS_VINITHI_IND (0x0400) |
| #define U300_SYSCON_BCR_APP_CPU_SUBSYS_VINITHI_IND (0x0200) |
| #define U300_SYSCON_BCR_EXTRA_BOOT_OPTION_MASK (0x01FC) |
| #define U300_SYSCON_BCR_APP_BOOT_SERV_MASK (0x0003) |
| |
| |
| /* CPU clock defines */ |
| /** |
| * CPU high frequency in MHz |
| */ |
| #define SYSCON_CPU_CLOCK_HIGH 208 |
| /** |
| * CPU medium frequency in MHz |
| */ |
| #define SYSCON_CPU_CLOCK_MEDIUM 52 |
| /** |
| * CPU low frequency in MHz |
| */ |
| #define SYSCON_CPU_CLOCK_LOW 13 |
| |
| /* EMIF clock defines */ |
| /** |
| * EMIF high frequency in MHz |
| */ |
| #define SYSCON_EMIF_CLOCK_HIGH 104 |
| /** |
| * EMIF medium frequency in MHz |
| */ |
| #define SYSCON_EMIF_CLOCK_MEDIUM 52 |
| /** |
| * EMIF low frequency in MHz |
| */ |
| #define SYSCON_EMIF_CLOCK_LOW 13 |
| |
| /* AHB clock defines */ |
| /** |
| * AHB high frequency in MHz |
| */ |
| #define SYSCON_AHB_CLOCK_HIGH 52 |
| /** |
| * AHB medium frequency in MHz |
| */ |
| #define SYSCON_AHB_CLOCK_MEDIUM 26 |
| /** |
| * AHB low frequency in MHz |
| */ |
| #define SYSCON_AHB_CLOCK_LOW 7 /* i.e 13/2=6.5MHz */ |
| |
| enum syscon_busmaster { |
| SYSCON_BM_DMAC, |
| SYSCON_BM_XGAM, |
| SYSCON_BM_VIDEO_ENC |
| }; |
| |
| /* Selectr a resistor or a set of resistors */ |
| enum syscon_pull_up_down { |
| SYSCON_PU_KEY_IN_EN, |
| SYSCON_PU_EMIF_1_8_BIT_EN, |
| SYSCON_PU_EMIF_1_16_BIT_EN, |
| SYSCON_PU_EMIF_1_NFIF_READY_EN, |
| SYSCON_PU_EMIF_1_NFIF_WAIT_N_EN, |
| }; |
| |
| /* |
| * Note that this array must match the order of the array "clk_reg" |
| * in syscon.c |
| */ |
| enum syscon_clk { |
| SYSCON_CLKCONTROL_SLOW_BRIDGE, |
| SYSCON_CLKCONTROL_UART, |
| SYSCON_CLKCONTROL_BTR, |
| SYSCON_CLKCONTROL_EH, |
| SYSCON_CLKCONTROL_GPIO, |
| SYSCON_CLKCONTROL_KEYPAD, |
| SYSCON_CLKCONTROL_APP_TIMER, |
| SYSCON_CLKCONTROL_ACC_TIMER, |
| SYSCON_CLKCONTROL_FAST_BRIDGE, |
| SYSCON_CLKCONTROL_I2C0, |
| SYSCON_CLKCONTROL_I2C1, |
| SYSCON_CLKCONTROL_I2S0, |
| SYSCON_CLKCONTROL_I2S1, |
| SYSCON_CLKCONTROL_MMC, |
| SYSCON_CLKCONTROL_SPI, |
| SYSCON_CLKCONTROL_I2S0_CORE, |
| SYSCON_CLKCONTROL_I2S1_CORE, |
| SYSCON_CLKCONTROL_UART1, |
| SYSCON_CLKCONTROL_AAIF, |
| SYSCON_CLKCONTROL_AHB, |
| SYSCON_CLKCONTROL_APEX, |
| SYSCON_CLKCONTROL_CPU, |
| SYSCON_CLKCONTROL_DMA, |
| SYSCON_CLKCONTROL_EMIF, |
| SYSCON_CLKCONTROL_NAND_IF, |
| SYSCON_CLKCONTROL_VIDEO_ENC, |
| SYSCON_CLKCONTROL_XGAM, |
| SYSCON_CLKCONTROL_SEMI, |
| SYSCON_CLKCONTROL_AHB_SUBSYS, |
| SYSCON_CLKCONTROL_MSPRO |
| }; |
| |
| enum syscon_sysclk_mode { |
| SYSCON_SYSCLK_DISABLED, |
| SYSCON_SYSCLK_M_CLK, |
| SYSCON_SYSCLK_ACC_FSM, |
| SYSCON_SYSCLK_PLL60_48, |
| SYSCON_SYSCLK_PLL60_60, |
| SYSCON_SYSCLK_ACC_PLL208, |
| SYSCON_SYSCLK_APP_PLL13, |
| SYSCON_SYSCLK_APP_FSM, |
| SYSCON_SYSCLK_RTC, |
| SYSCON_SYSCLK_APP_PLL208 |
| }; |
| |
| enum syscon_sysclk_req { |
| SYSCON_SYSCLKREQ_DISABLED, |
| SYSCON_SYSCLKREQ_ACTIVE_LOW, |
| SYSCON_SYSCLKREQ_MONITOR |
| }; |
| |
| enum syscon_clk_mode { |
| SYSCON_CLKMODE_OFF, |
| SYSCON_CLKMODE_DEFAULT, |
| SYSCON_CLKMODE_LOW, |
| SYSCON_CLKMODE_MEDIUM, |
| SYSCON_CLKMODE_HIGH, |
| SYSCON_CLKMODE_PERMANENT, |
| SYSCON_CLKMODE_ON, |
| }; |
| |
| enum syscon_call_mode { |
| SYSCON_CLKCALL_NOWAIT, |
| SYSCON_CLKCALL_WAIT, |
| }; |
| |
| int syscon_dc_on(bool keep_power_on); |
| int syscon_set_busmaster_active_state(enum syscon_busmaster busmaster, |
| bool active); |
| bool syscon_get_busmaster_active_state(void); |
| int syscon_set_sleep_mask(enum syscon_clk, |
| bool sleep_ctrl); |
| int syscon_config_sysclk(u32 sysclk, |
| enum syscon_sysclk_mode sysclkmode, |
| bool inverse, |
| u32 divisor, |
| enum syscon_sysclk_req sysclkreq); |
| bool syscon_can_turn_off_semi_clock(void); |
| |
| /* This function is restricted to core.c */ |
| int syscon_request_normal_power(bool req); |
| |
| /* This function is restricted to be used by platform_speed.c */ |
| int syscon_speed_request(enum syscon_call_mode wait_mode, |
| enum syscon_clk_mode req_clk_mode); |
| #endif /* __MACH_SYSCON_H */ |
