blob: d0dd81790f746c06699bb6f116af78144fe5f5df [file] [log] [blame]
/*
* Setup pointers to hardware dependent routines.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1996, 1997, 2004, 05 by Ralf Baechle (ralf@linux-mips.org)
* Copyright (C) 2001, 2002, 2003 by Liam Davies (ldavies@agile.tv)
*
*/
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/pm.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <asm/bootinfo.h>
#include <asm/time.h>
#include <asm/io.h>
#include <asm/reboot.h>
#include <asm/gt64120.h>
#include <cobalt.h>
extern void cobalt_machine_restart(char *command);
extern void cobalt_machine_halt(void);
extern void cobalt_machine_power_off(void);
extern void cobalt_early_console(void);
int cobalt_board_id;
const char *get_system_type(void)
{
switch (cobalt_board_id) {
case COBALT_BRD_ID_QUBE1:
return "Cobalt Qube";
case COBALT_BRD_ID_RAQ1:
return "Cobalt RaQ";
case COBALT_BRD_ID_QUBE2:
return "Cobalt Qube2";
case COBALT_BRD_ID_RAQ2:
return "Cobalt RaQ2";
}
return "MIPS Cobalt";
}
void __init plat_timer_setup(struct irqaction *irq)
{
/* Load timer value for HZ (TCLK is 50MHz) */
GT_WRITE(GT_TC0_OFS, 50*1000*1000 / HZ);
/* Enable timer */
GT_WRITE(GT_TC_CONTROL_OFS, GT_TC_CONTROL_ENTC0_MSK | GT_TC_CONTROL_SELTC0_MSK);
/* Register interrupt */
setup_irq(COBALT_GALILEO_IRQ, irq);
/* Enable interrupt */
GT_WRITE(GT_INTRMASK_OFS, GT_INTR_T0EXP_MSK | GT_READ(GT_INTRMASK_OFS));
}
/*
* Cobalt doesn't have PS/2 keyboard/mouse interfaces,
* keyboard conntroller is never used.
* Also PCI-ISA bridge DMA contoroller is never used.
*/
static struct resource cobalt_reserved_resources[] = {
{ /* dma1 */
.start = 0x00,
.end = 0x1f,
.name = "reserved",
.flags = IORESOURCE_BUSY | IORESOURCE_IO,
},
{ /* keyboard */
.start = 0x60,
.end = 0x6f,
.name = "reserved",
.flags = IORESOURCE_BUSY | IORESOURCE_IO,
},
{ /* dma page reg */
.start = 0x80,
.end = 0x8f,
.name = "reserved",
.flags = IORESOURCE_BUSY | IORESOURCE_IO,
},
{ /* dma2 */
.start = 0xc0,
.end = 0xdf,
.name = "reserved",
.flags = IORESOURCE_BUSY | IORESOURCE_IO,
},
};
void __init plat_mem_setup(void)
{
static struct uart_port uart;
unsigned int devfn = PCI_DEVFN(COBALT_PCICONF_VIA, 0);
int i;
_machine_restart = cobalt_machine_restart;
_machine_halt = cobalt_machine_halt;
pm_power_off = cobalt_machine_power_off;
set_io_port_base(CKSEG1ADDR(GT_DEF_PCI0_IO_BASE));
/* I/O port resource must include LCD/buttons */
ioport_resource.end = 0x0fffffff;
/* These resources have been reserved by VIA SuperI/O chip. */
for (i = 0; i < ARRAY_SIZE(cobalt_reserved_resources); i++)
request_resource(&ioport_resource, cobalt_reserved_resources + i);
/* Read the cobalt id register out of the PCI config space */
PCI_CFG_SET(devfn, (VIA_COBALT_BRD_ID_REG & ~0x3));
cobalt_board_id = GT_READ(GT_PCI0_CFGDATA_OFS);
cobalt_board_id >>= ((VIA_COBALT_BRD_ID_REG & 3) * 8);
cobalt_board_id = VIA_COBALT_BRD_REG_to_ID(cobalt_board_id);
printk("Cobalt board ID: %d\n", cobalt_board_id);
if (cobalt_board_id > COBALT_BRD_ID_RAQ1) {
#ifdef CONFIG_SERIAL_8250
uart.line = 0;
uart.type = PORT_UNKNOWN;
uart.uartclk = 18432000;
uart.irq = COBALT_SERIAL_IRQ;
uart.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF |
UPF_SKIP_TEST;
uart.iotype = UPIO_MEM;
uart.mapbase = 0x1c800000;
early_serial_setup(&uart);
#endif
}
}
/*
* Prom init. We read our one and only communication with the firmware.
* Grab the amount of installed memory.
* Better boot loaders (CoLo) pass a command line too :-)
*/
void __init prom_init(void)
{
int narg, indx, posn, nchr;
unsigned long memsz;
char **argv;
mips_machgroup = MACH_GROUP_COBALT;
memsz = fw_arg0 & 0x7fff0000;
narg = fw_arg0 & 0x0000ffff;
if (narg) {
arcs_cmdline[0] = '\0';
argv = (char **) fw_arg1;
posn = 0;
for (indx = 1; indx < narg; ++indx) {
nchr = strlen(argv[indx]);
if (posn + 1 + nchr + 1 > sizeof(arcs_cmdline))
break;
if (posn)
arcs_cmdline[posn++] = ' ';
strcpy(arcs_cmdline + posn, argv[indx]);
posn += nchr;
}
}
add_memory_region(0x0, memsz, BOOT_MEM_RAM);
}
void __init prom_free_prom_memory(void)
{
/* Nothing to do! */
}