| /* |
| * linux/arch/arm/mach-sa1100/shannon.c |
| */ |
| |
| #include <linux/config.h> |
| #include <linux/init.h> |
| #include <linux/device.h> |
| #include <linux/kernel.h> |
| #include <linux/tty.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| |
| #include <asm/hardware.h> |
| #include <asm/mach-types.h> |
| #include <asm/setup.h> |
| |
| #include <asm/mach/arch.h> |
| #include <asm/mach/flash.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/serial_sa1100.h> |
| #include <asm/arch/mcp.h> |
| #include <asm/arch/shannon.h> |
| |
| #include "generic.h" |
| |
| static struct mtd_partition shannon_partitions[] = { |
| { |
| .name = "BLOB boot loader", |
| .offset = 0, |
| .size = 0x20000 |
| }, |
| { |
| .name = "kernel", |
| .offset = MTDPART_OFS_APPEND, |
| .size = 0xe0000 |
| }, |
| { |
| .name = "initrd", |
| .offset = MTDPART_OFS_APPEND, |
| .size = MTDPART_SIZ_FULL |
| } |
| }; |
| |
| static struct flash_platform_data shannon_flash_data = { |
| .map_name = "cfi_probe", |
| .parts = shannon_partitions, |
| .nr_parts = ARRAY_SIZE(shannon_partitions), |
| }; |
| |
| static struct resource shannon_flash_resource = { |
| .start = SA1100_CS0_PHYS, |
| .end = SA1100_CS0_PHYS + SZ_4M - 1, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct mcp_plat_data shannon_mcp_data = { |
| .mccr0 = MCCR0_ADM, |
| .sclk_rate = 11981000, |
| }; |
| |
| static void __init shannon_init(void) |
| { |
| sa11x0_set_flash_data(&shannon_flash_data, &shannon_flash_resource, 1); |
| sa11x0_set_mcp_data(&shannon_mcp_data); |
| } |
| |
| static void __init shannon_map_io(void) |
| { |
| sa1100_map_io(); |
| |
| sa1100_register_uart(0, 3); |
| sa1100_register_uart(1, 1); |
| |
| Ser1SDCR0 |= SDCR0_SUS; |
| GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD); |
| GPDR |= GPIO_UART_TXD | SHANNON_GPIO_CODEC_RESET; |
| GPDR &= ~GPIO_UART_RXD; |
| PPAR |= PPAR_UPR; |
| |
| /* reset the codec */ |
| GPCR = SHANNON_GPIO_CODEC_RESET; |
| GPSR = SHANNON_GPIO_CODEC_RESET; |
| } |
| |
| MACHINE_START(SHANNON, "Shannon (AKA: Tuxscreen)") |
| .phys_io = 0x80000000, |
| .io_pg_offst = ((0xf8000000) >> 18) & 0xfffc, |
| .boot_params = 0xc0000100, |
| .map_io = shannon_map_io, |
| .init_irq = sa1100_init_irq, |
| .timer = &sa1100_timer, |
| .init_machine = shannon_init, |
| MACHINE_END |