blob: 43e36060da186f6e8b0db445001b89fb576c5350 [file] [log] [blame]
/***************************************************************************/
/*
* linux/arch/m68knommu/platform/5272/config.c
*
* Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com)
* Copyright (C) 2001-2002, SnapGear Inc. (www.snapgear.com)
*/
/***************************************************************************/
#include <linux/kernel.h>
#include <linux/param.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#include <asm/mcfuart.h>
#include <asm/mcfgpio.h>
/***************************************************************************/
/*
* Some platforms need software versions of the GPIO data registers.
*/
unsigned short ppdata;
unsigned char ledbank = 0xff;
/***************************************************************************/
struct mcf_gpio_chip mcf_gpio_chips[] = {
MCFGPS(PA, 0, 16, MCFSIM_PADDR, MCFSIM_PADAT, MCFSIM_PADAT),
MCFGPS(PB, 16, 16, MCFSIM_PBDDR, MCFSIM_PBDAT, MCFSIM_PBDAT),
MCFGPS(Pc, 32, 16, MCFSIM_PCDDR, MCFSIM_PCDAT, MCFSIM_PCDAT),
};
unsigned int mcf_gpio_chips_size = ARRAY_SIZE(mcf_gpio_chips);
/***************************************************************************/
static void __init m5272_uarts_init(void)
{
u32 v;
/* Enable the output lines for the serial ports */
v = readl(MCF_MBAR + MCFSIM_PBCNT);
v = (v & ~0x000000ff) | 0x00000055;
writel(v, MCF_MBAR + MCFSIM_PBCNT);
v = readl(MCF_MBAR + MCFSIM_PDCNT);
v = (v & ~0x000003fc) | 0x000002a8;
writel(v, MCF_MBAR + MCFSIM_PDCNT);
}
/***************************************************************************/
static void m5272_cpu_reset(void)
{
local_irq_disable();
/* Set watchdog to reset, and enabled */
__raw_writew(0, MCF_MBAR + MCFSIM_WIRR);
__raw_writew(1, MCF_MBAR + MCFSIM_WRRR);
__raw_writew(0, MCF_MBAR + MCFSIM_WCR);
for (;;)
/* wait for watchdog to timeout */;
}
/***************************************************************************/
void __init config_BSP(char *commandp, int size)
{
#if defined (CONFIG_MOD5272)
volatile unsigned char *pivrp;
/* Set base of device vectors to be 64 */
pivrp = (volatile unsigned char *) (MCF_MBAR + MCFSIM_PIVR);
*pivrp = 0x40;
#endif
#if defined(CONFIG_NETtel) || defined(CONFIG_SCALES)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0004000, size);
commandp[size-1] = 0;
#elif defined(CONFIG_CANCam)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0010000, size);
commandp[size-1] = 0;
#endif
mach_reset = m5272_cpu_reset;
mach_sched_init = hw_timer_init;
}
/***************************************************************************/
/*
* Some 5272 based boards have the FEC ethernet diectly connected to
* an ethernet switch. In this case we need to use the fixed phy type,
* and we need to declare it early in boot.
*/
static struct fixed_phy_status nettel_fixed_phy_status __initdata = {
.link = 1,
.speed = 100,
.duplex = 0,
};
/***************************************************************************/
static int __init init_BSP(void)
{
m5272_uarts_init();
fixed_phy_add(PHY_POLL, 0, &nettel_fixed_phy_status);
return 0;
}
arch_initcall(init_BSP);
/***************************************************************************/