| /* |
| * arch/arm/mach-aaec2000/include/mach/aaec2000.h |
| * |
| * AAEC-2000 registers definition |
| * |
| * Copyright (c) 2005 Nicolas Bellido Y Ortega |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #ifndef __ASM_ARCH_AAEC2000_H |
| #define __ASM_ARCH_AAEC2000_H |
| |
| #ifndef __ASM_ARCH_HARDWARE_H |
| #error You must include hardware.h not this file |
| #endif /* __ASM_ARCH_HARDWARE_H */ |
| |
| /* Chip selects */ |
| #define AAEC_CS0 0x00000000 |
| #define AAEC_CS1 0x10000000 |
| #define AAEC_CS2 0x20000000 |
| #define AAEC_CS3 0x30000000 |
| |
| /* Flash */ |
| #define AAEC_FLASH_BASE AAEC_CS0 |
| #define AAEC_FLASH_SIZE SZ_64M |
| |
| /* Interrupt controller */ |
| #define IRQ_BASE __REG(0x80000500) |
| #define IRQ_INTSR __REG(0x80000500) /* Int Status Register */ |
| #define IRQ_INTRSR __REG(0x80000504) /* Int Raw (unmasked) Status */ |
| #define IRQ_INTENS __REG(0x80000508) /* Int Enable Set */ |
| #define IRQ_INTENC __REG(0x8000050c) /* Int Enable Clear */ |
| |
| /* UART 1 */ |
| #define UART1_BASE __REG(0x80000600) |
| #define UART1_DR __REG(0x80000600) /* Data/FIFO Register */ |
| #define UART1_LCR __REG(0x80000604) /* Link Control Register */ |
| #define UART1_BRCR __REG(0x80000608) /* Baud Rate Control Register */ |
| #define UART1_CR __REG(0x8000060c) /* Control Register */ |
| #define UART1_SR __REG(0x80000610) /* Status Register */ |
| #define UART1_INT __REG(0x80000614) /* Interrupt Status Register */ |
| #define UART1_INTM __REG(0x80000618) /* Interrupt Mask Register */ |
| #define UART1_INTRES __REG(0x8000061c) /* Int Result (masked status) Register */ |
| |
| /* UART 2 */ |
| #define UART2_BASE __REG(0x80000700) |
| #define UART2_DR __REG(0x80000700) /* Data/FIFO Register */ |
| #define UART2_LCR __REG(0x80000704) /* Link Control Register */ |
| #define UART2_BRCR __REG(0x80000708) /* Baud Rate Control Register */ |
| #define UART2_CR __REG(0x8000070c) /* Control Register */ |
| #define UART2_SR __REG(0x80000710) /* Status Register */ |
| #define UART2_INT __REG(0x80000714) /* Interrupt Status Register */ |
| #define UART2_INTM __REG(0x80000718) /* Interrupt Mask Register */ |
| #define UART2_INTRES __REG(0x8000071c) /* Int Result (masked status) Register */ |
| |
| /* UART 3 */ |
| #define UART3_BASE __REG(0x80000800) |
| #define UART3_DR __REG(0x80000800) /* Data/FIFO Register */ |
| #define UART3_LCR __REG(0x80000804) /* Link Control Register */ |
| #define UART3_BRCR __REG(0x80000808) /* Baud Rate Control Register */ |
| #define UART3_CR __REG(0x8000080c) /* Control Register */ |
| #define UART3_SR __REG(0x80000810) /* Status Register */ |
| #define UART3_INT __REG(0x80000814) /* Interrupt Status Register */ |
| #define UART3_INTM __REG(0x80000818) /* Interrupt Mask Register */ |
| #define UART3_INTRES __REG(0x8000081c) /* Int Result (masked status) Register */ |
| |
| /* These are used in some places */ |
| #define _UART1_BASE __PREG(UART1_BASE) |
| #define _UART2_BASE __PREG(UART2_BASE) |
| #define _UART3_BASE __PREG(UART3_BASE) |
| |
| /* UART Registers Offsets */ |
| #define UART_DR 0x00 |
| #define UART_LCR 0x04 |
| #define UART_BRCR 0x08 |
| #define UART_CR 0x0c |
| #define UART_SR 0x10 |
| #define UART_INT 0x14 |
| #define UART_INTM 0x18 |
| #define UART_INTRES 0x1c |
| |
| /* UART_LCR Bitmask */ |
| #define UART_LCR_BRK (1 << 0) /* Send Break */ |
| #define UART_LCR_PEN (1 << 1) /* Parity Enable */ |
| #define UART_LCR_EP (1 << 2) /* Even/Odd Parity */ |
| #define UART_LCR_S2 (1 << 3) /* One/Two Stop bits */ |
| #define UART_LCR_FIFO (1 << 4) /* FIFO Enable */ |
| #define UART_LCR_WL5 (0 << 5) /* Word Length - 5 bits */ |
| #define UART_LCR_WL6 (1 << 5) /* Word Length - 6 bits */ |
| #define UART_LCR_WL7 (1 << 6) /* Word Length - 7 bits */ |
| #define UART_LCR_WL8 (1 << 7) /* Word Length - 8 bits */ |
| |
| /* UART_CR Bitmask */ |
| #define UART_CR_EN (1 << 0) /* UART Enable */ |
| #define UART_CR_SIR (1 << 1) /* IrDA SIR Enable */ |
| #define UART_CR_SIRLP (1 << 2) /* Low Power IrDA Enable */ |
| #define UART_CR_RXP (1 << 3) /* Receive Pin Polarity */ |
| #define UART_CR_TXP (1 << 4) /* Transmit Pin Polarity */ |
| #define UART_CR_MXP (1 << 5) /* Modem Pin Polarity */ |
| #define UART_CR_LOOP (1 << 6) /* Loopback Mode */ |
| |
| /* UART_SR Bitmask */ |
| #define UART_SR_CTS (1 << 0) /* Clear To Send Status */ |
| #define UART_SR_DSR (1 << 1) /* Data Set Ready Status */ |
| #define UART_SR_DCD (1 << 2) /* Data Carrier Detect Status */ |
| #define UART_SR_TxBSY (1 << 3) /* Transmitter Busy Status */ |
| #define UART_SR_RxFE (1 << 4) /* Receive FIFO Empty Status */ |
| #define UART_SR_TxFF (1 << 5) /* Transmit FIFO Full Status */ |
| #define UART_SR_RxFF (1 << 6) /* Receive FIFO Full Status */ |
| #define UART_SR_TxFE (1 << 7) /* Transmit FIFO Empty Status */ |
| |
| /* UART_INT Bitmask */ |
| #define UART_INT_RIS (1 << 0) /* Rx Interrupt */ |
| #define UART_INT_TIS (1 << 1) /* Tx Interrupt */ |
| #define UART_INT_MIS (1 << 2) /* Modem Interrupt */ |
| #define UART_INT_RTIS (1 << 3) /* Receive Timeout Interrupt */ |
| |
| /* Timer 1 */ |
| #define TIMER1_BASE __REG(0x80000c00) |
| #define TIMER1_LOAD __REG(0x80000c00) /* Timer 1 Load Register */ |
| #define TIMER1_VAL __REG(0x80000c04) /* Timer 1 Value Register */ |
| #define TIMER1_CTRL __REG(0x80000c08) /* Timer 1 Control Register */ |
| #define TIMER1_CLEAR __REG(0x80000c0c) /* Timer 1 Clear Register */ |
| |
| /* Timer 2 */ |
| #define TIMER2_BASE __REG(0x80000d00) |
| #define TIMER2_LOAD __REG(0x80000d00) /* Timer 2 Load Register */ |
| #define TIMER2_VAL __REG(0x80000d04) /* Timer 2 Value Register */ |
| #define TIMER2_CTRL __REG(0x80000d08) /* Timer 2 Control Register */ |
| #define TIMER2_CLEAR __REG(0x80000d0c) /* Timer 2 Clear Register */ |
| |
| /* Timer 3 */ |
| #define TIMER3_BASE __REG(0x80000e00) |
| #define TIMER3_LOAD __REG(0x80000e00) /* Timer 3 Load Register */ |
| #define TIMER3_VAL __REG(0x80000e04) /* Timer 3 Value Register */ |
| #define TIMER3_CTRL __REG(0x80000e08) /* Timer 3 Control Register */ |
| #define TIMER3_CLEAR __REG(0x80000e0c) /* Timer 3 Clear Register */ |
| |
| /* Timer Control register bits */ |
| #define TIMER_CTRL_ENABLE (1 << 7) /* Enable (Start Timer) */ |
| #define TIMER_CTRL_PERIODIC (1 << 6) /* Periodic Running Mode */ |
| #define TIMER_CTRL_FREE_RUNNING (0 << 6) /* Normal Running Mode */ |
| #define TIMER_CTRL_CLKSEL_508K (1 << 3) /* 508KHz Clock select (Timer 1, 2) */ |
| #define TIMER_CTRL_CLKSEL_2K (0 << 3) /* 2KHz Clock Select (Timer 1, 2) */ |
| |
| /* Power and State Control */ |
| #define POWER_BASE __REG(0x80000400) |
| #define POWER_PWRSR __REG(0x80000400) /* Power Status Register */ |
| #define POWER_PWRCNT __REG(0x80000404) /* Power/Clock control */ |
| #define POWER_HALT __REG(0x80000408) /* Power Idle Mode */ |
| #define POWER_STDBY __REG(0x8000040c) /* Power Standby Mode */ |
| #define POWER_BLEOI __REG(0x80000410) /* Battery Low End of Interrupt */ |
| #define POWER_MCEOI __REG(0x80000414) /* Media Changed EoI */ |
| #define POWER_TEOI __REG(0x80000418) /* Tick EoI */ |
| #define POWER_STFCLR __REG(0x8000041c) /* NbFlg, RSTFlg, PFFlg, CLDFlg Clear */ |
| #define POWER_CLKSET __REG(0x80000420) /* Clock Speed Control */ |
| |
| /* GPIO Registers */ |
| #define AAEC_GPIO_PHYS 0x80000e00 |
| |
| #define AAEC_GPIO_PADR __REG(AAEC_GPIO_PHYS + 0x00) |
| #define AAEC_GPIO_PBDR __REG(AAEC_GPIO_PHYS + 0x04) |
| #define AAEC_GPIO_PCDR __REG(AAEC_GPIO_PHYS + 0x08) |
| #define AAEC_GPIO_PDDR __REG(AAEC_GPIO_PHYS + 0x0c) |
| #define AAEC_GPIO_PADDR __REG(AAEC_GPIO_PHYS + 0x10) |
| #define AAEC_GPIO_PBDDR __REG(AAEC_GPIO_PHYS + 0x14) |
| #define AAEC_GPIO_PCDDR __REG(AAEC_GPIO_PHYS + 0x18) |
| #define AAEC_GPIO_PDDDR __REG(AAEC_GPIO_PHYS + 0x1c) |
| #define AAEC_GPIO_PEDR __REG(AAEC_GPIO_PHYS + 0x20) |
| #define AAEC_GPIO_PEDDR __REG(AAEC_GPIO_PHYS + 0x24) |
| #define AAEC_GPIO_KSCAN __REG(AAEC_GPIO_PHYS + 0x28) |
| #define AAEC_GPIO_PINMUX __REG(AAEC_GPIO_PHYS + 0x2c) |
| #define AAEC_GPIO_PFDR __REG(AAEC_GPIO_PHYS + 0x30) |
| #define AAEC_GPIO_PFDDR __REG(AAEC_GPIO_PHYS + 0x34) |
| #define AAEC_GPIO_PGDR __REG(AAEC_GPIO_PHYS + 0x38) |
| #define AAEC_GPIO_PGDDR __REG(AAEC_GPIO_PHYS + 0x3c) |
| #define AAEC_GPIO_PHDR __REG(AAEC_GPIO_PHYS + 0x40) |
| #define AAEC_GPIO_PHDDR __REG(AAEC_GPIO_PHYS + 0x44) |
| #define AAEC_GPIO_RAZ __REG(AAEC_GPIO_PHYS + 0x48) |
| #define AAEC_GPIO_INTTYPE1 __REG(AAEC_GPIO_PHYS + 0x4c) |
| #define AAEC_GPIO_INTTYPE2 __REG(AAEC_GPIO_PHYS + 0x50) |
| #define AAEC_GPIO_FEOI __REG(AAEC_GPIO_PHYS + 0x54) |
| #define AAEC_GPIO_INTEN __REG(AAEC_GPIO_PHYS + 0x58) |
| #define AAEC_GPIO_INTSTATUS __REG(AAEC_GPIO_PHYS + 0x5c) |
| #define AAEC_GPIO_RAWINTSTATUS __REG(AAEC_GPIO_PHYS + 0x60) |
| #define AAEC_GPIO_DB __REG(AAEC_GPIO_PHYS + 0x64) |
| #define AAEC_GPIO_PAPINDR __REG(AAEC_GPIO_PHYS + 0x68) |
| #define AAEC_GPIO_PBPINDR __REG(AAEC_GPIO_PHYS + 0x6c) |
| #define AAEC_GPIO_PCPINDR __REG(AAEC_GPIO_PHYS + 0x70) |
| #define AAEC_GPIO_PDPINDR __REG(AAEC_GPIO_PHYS + 0x74) |
| #define AAEC_GPIO_PEPINDR __REG(AAEC_GPIO_PHYS + 0x78) |
| #define AAEC_GPIO_PFPINDR __REG(AAEC_GPIO_PHYS + 0x7c) |
| #define AAEC_GPIO_PGPINDR __REG(AAEC_GPIO_PHYS + 0x80) |
| #define AAEC_GPIO_PHPINDR __REG(AAEC_GPIO_PHYS + 0x84) |
| |
| #define AAEC_GPIO_PINMUX_PE0CON (1 << 0) |
| #define AAEC_GPIO_PINMUX_PD0CON (1 << 1) |
| #define AAEC_GPIO_PINMUX_CODECON (1 << 2) |
| #define AAEC_GPIO_PINMUX_UART3CON (1 << 3) |
| |
| /* LCD Controller */ |
| #define AAEC_CLCD_PHYS 0x80003000 |
| |
| #endif /* __ARM_ARCH_AAEC2000_H */ |
