| |
| These were the tests done to validate the Diffserv scripts. |
| This document will be updated continously. If you do more |
| thorough validation testing please post the details to the |
| diffserv mailing list. |
| Nevertheless, these tests should serve for basic validation. |
| |
| AFCBQ, EFCBQ, EFPRIO |
| ---------------------- |
| |
| generate all possible DSCPs and observe that they |
| get sent to the proper classes. In the case of AF also |
| to the correct Virtual Queues. |
| |
| Edge1 |
| ----- |
| generate TOS values 0x0,0x10,0xbb each with IP addresses |
| 10.2.0.24 (mark 1), 10.2.0.3 (mark2) and 10.2.0.30 (mark 3) |
| and observe that they get marked as expected. |
| |
| Edge2 |
| ----- |
| |
| -Repeat the tests in Edge1 |
| -ftp with data direction from 10.2.0.2 |
| *observe that the metering/policing works correctly (and the marking |
| as well). In this case the mark used will be 3 |
| |
| Edge31-cb-chains |
| ---------------- |
| |
| -ftp with data direction from 10.2.0.2 |
| |
| *observe that the metering/policing works correctly (and the marking |
| as well). In this case the mark used will be 1. |
| |
| Metering: The data throughput should not exceed 2*CIR1 + 2*CIR2 |
| which is roughly: 5mbps |
| |
| Marking: the should be a variation of marked packets: |
| AF41(TOS=0x88) AF42(0x90) AF43(0x98) and BE (0x0) |
| |
| More tests required to see the interaction of several sources (other |
| than subnet 10.2.0.0/24). |
| |
| Edge31-ca-u32 |
| -------------- |
| |
| Generate data using modified tcpblast from 10.2.0.2 (behind eth2) to the |
| discard port of 10.1.0.2 (behind eth1) |
| |
| 1) generate with src tos = 0x88 |
| Metering: Allocated throughput should not exceed 2*CIR1 + 2*CIR2 |
| approximately 5mbps |
| Marking: Should vary between 0x88,0x90,0x98 and 0x0 |
| |
| 2) generate with src tos = 0x90 |
| Metering: Allocated throughput should not exceed CIR1 + 2*CIR2 |
| approximately 3.5mbps |
| Marking: Should vary between 0x90,0x98 and 0x0 |
| |
| 3) generate with src tos = 0x98 |
| Metering: Allocated throughput should not exceed CIR1 + CIR2 |
| approximately 2.5mbps |
| Marking: Should vary between 0x98 and 0x0 |
| |
| 4) generate with src tos any other than the above |
| Metering: Allocated throughput should not exceed CIR1 |
| approximately 1.5mbps |
| Marking: Should be consistent at 0x0 |
| |
| TODO: Testing on how each color shares when all 4 types of packets |
| are going through the edge device |
| |
| Edge32-cb-u32, Edge32-cb-chains |
| ------------------------------- |
| |
| -ftp with data direction from 10.2.0.2 |
| |
| *observe that the metering/policing works correctly (and the marking |
| as well). |
| |
| Metering: |
| The data throughput should not exceed 2*CIR1 + 2*CIR2 |
| + 2*PIR2 + PIR1 for u32 which is roughly: 6mbps |
| The data throughput should not exceed 2*CIR1 + 5*CIR2 |
| for chains which is roughly: 6mbps |
| |
| Marking: the should be a variation of marked packets: |
| AF41(TOS=0x88) AF42(0x90) AF43(0x98) and BE (0x0) |
| |
| TODO: |
| -More tests required to see the interaction of several sources (other |
| than subnet 10.2.0.0/24). |
| -More tests needed to capture stats on how many times the CIR was exceeded |
| but the data was not remarked etc. |
| |
| Edge32-ca-u32 |
| -------------- |
| |
| Generate data using modified tcpblast from 10.2.0.2 (behind eth2) to the |
| discard port of 10.1.0.2 (behind eth1) |
| |
| 1) generate with src tos = 0x88 |
| Metering: Allocated throughput should not exceed 2*CIR1 + 2*CIR2 |
| +PIR1 -- approximately 4mbps |
| Marking: Should vary between 0x88,0x90,0x98 and 0x0 |
| |
| 2) generate with src tos = 0x90 |
| Metering: Allocated throughput should not exceed CIR1 + 2*CIR2 |
| + 2* PIR2 approximately 3mbps |
| Marking: Should vary between 0x90,0x98 and 0x0 |
| |
| 3) generate with src tos = 0x98 |
| Metering: Allocated throughput should not exceed PIR1+ CIR1 + CIR2 |
| approximately 2.5mbps |
| Marking: Should vary between 0x98 and 0x0 |
| |
| 4) generate with src tos any other than the above |
| Metering: Allocated throughput should not exceed CIR1 |
| approximately 1mbps |
| Marking: Should be consistent at 0x0 |
| |
| TODO: Testing on how each color shares when all 4 types of packets |
| are going through the edge device |
