/*
 * Copyright (c) Realtek Semiconductor Corp. All rights reserved.
 *
 * Module Name:
 *	r8185b_init.c
 *
 * Abstract:
 *	Hardware Initialization and Hardware IO for RTL8185B
 *
 * Major Change History:
 *	When		Who				What
 *	----------	---------------		-------------------------------
 *	2006-11-15	Xiong			Created
 *
 * Notes:
 *	This file is ported from RTL8185B Windows driver.
 *
 *
 */

/*--------------------------Include File------------------------------------*/
#include <linux/spinlock.h>
#include "r8180_hw.h"
#include "r8180.h"
#include "r8180_rtl8225.h" /* RTL8225 Radio frontend */
#include "r8180_93cx6.h"   /* Card EEPROM */
#include "r8180_wx.h"
#include "ieee80211/dot11d.h"
/* #define CONFIG_RTL8180_IO_MAP */
#define TC_3W_POLL_MAX_TRY_CNT 5

static u8 MAC_REG_TABLE[][2] =	{
	/*PAGA 0:	*/
	/* 0x34(BRSR), 0xBE(RATE_FALLBACK_CTL), 0x1E0(ARFR) would set in HwConfigureRTL8185() */
	/* 0x272(RFSW_CTRL), 0x1CE(AESMSK_QC) set in InitializeAdapter8185(). */
	/* 0x1F0~0x1F8  set in MacConfig_85BASIC() */
	{0x08, 0xae}, {0x0a, 0x72}, {0x5b, 0x42},
	{0x84, 0x88}, {0x85, 0x24}, {0x88, 0x54}, {0x8b, 0xb8}, {0x8c, 0x03},
	{0x8d, 0x40}, {0x8e, 0x00}, {0x8f, 0x00}, {0x5b, 0x18}, {0x91, 0x03},
	{0x94, 0x0F}, {0x95, 0x32},
	{0x96, 0x00}, {0x97, 0x07}, {0xb4, 0x22}, {0xdb, 0x00},
	{0xf0, 0x32}, {0xf1, 0x32}, {0xf2, 0x00}, {0xf3, 0x00}, {0xf4, 0x32},
	{0xf5, 0x43}, {0xf6, 0x00}, {0xf7, 0x00}, {0xf8, 0x46}, {0xf9, 0xa4},
	{0xfa, 0x00}, {0xfb, 0x00}, {0xfc, 0x96}, {0xfd, 0xa4}, {0xfe, 0x00},
	{0xff, 0x00},

	/*PAGE 1: */
	/* For Flextronics system Logo PCIHCT failure: */
	/* 0x1C4~0x1CD set no-zero value to avoid PCI configuration space 0x45[7]=1 */
	{0x5e, 0x01},
	{0x58, 0x00}, {0x59, 0x00}, {0x5a, 0x04}, {0x5b, 0x00}, {0x60, 0x24},
	{0x61, 0x97}, {0x62, 0xF0}, {0x63, 0x09}, {0x80, 0x0F}, {0x81, 0xFF},
	{0x82, 0xFF}, {0x83, 0x03},
	{0xC4, 0x22}, {0xC5, 0x22}, {0xC6, 0x22}, {0xC7, 0x22}, {0xC8, 0x22}, /* lzm add 080826 */
	{0xC9, 0x22}, {0xCA, 0x22}, {0xCB, 0x22}, {0xCC, 0x22}, {0xCD, 0x22}, /* lzm add 080826 */
	{0xe2, 0x00},


	/* PAGE 2: */
	{0x5e, 0x02},
	{0x0c, 0x04}, {0x4c, 0x30}, {0x4d, 0x08}, {0x50, 0x05}, {0x51, 0xf5},
	{0x52, 0x04}, {0x53, 0xa0}, {0x54, 0xff}, {0x55, 0xff}, {0x56, 0xff},
	{0x57, 0xff}, {0x58, 0x08}, {0x59, 0x08}, {0x5a, 0x08}, {0x5b, 0x08},
	{0x60, 0x08}, {0x61, 0x08}, {0x62, 0x08}, {0x63, 0x08}, {0x64, 0x2f},
	{0x8c, 0x3f}, {0x8d, 0x3f}, {0x8e, 0x3f},
	{0x8f, 0x3f}, {0xc4, 0xff}, {0xc5, 0xff}, {0xc6, 0xff}, {0xc7, 0xff},
	{0xc8, 0x00}, {0xc9, 0x00}, {0xca, 0x80}, {0xcb, 0x00},

	/* PAGA 0: */
	{0x5e, 0x00}, {0x9f, 0x03}
	};


static u8  ZEBRA_AGC[] = {
	0,
	0x7E, 0x7E, 0x7E, 0x7E, 0x7D, 0x7C, 0x7B, 0x7A, 0x79, 0x78, 0x77, 0x76, 0x75, 0x74, 0x73, 0x72,
	0x71, 0x70, 0x6F, 0x6E, 0x6D, 0x6C, 0x6B, 0x6A, 0x69, 0x68, 0x67, 0x66, 0x65, 0x64, 0x63, 0x62,
	0x48, 0x47, 0x46, 0x45, 0x44, 0x29, 0x28, 0x27, 0x26, 0x25, 0x24, 0x23, 0x22, 0x21, 0x08, 0x07,
	0x06, 0x05, 0x04, 0x03, 0x02, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x10, 0x11, 0x12, 0x13, 0x15, 0x16,
	0x17, 0x17, 0x18, 0x18, 0x19, 0x1a, 0x1a, 0x1b, 0x1b, 0x1c, 0x1c, 0x1d, 0x1d, 0x1d, 0x1e, 0x1e,
	0x1f, 0x1f, 0x1f, 0x20, 0x20, 0x20, 0x20, 0x21, 0x21, 0x21, 0x22, 0x22, 0x22, 0x23, 0x23, 0x24,
	0x24, 0x25, 0x25, 0x25, 0x26, 0x26, 0x27, 0x27, 0x2F, 0x2F, 0x2F, 0x2F, 0x2F, 0x2F, 0x2F, 0x2F
	};

static u32 ZEBRA_RF_RX_GAIN_TABLE[] = {
	0x0096, 0x0076, 0x0056, 0x0036, 0x0016, 0x01f6, 0x01d6, 0x01b6,
	0x0196, 0x0176, 0x00F7, 0x00D7, 0x00B7, 0x0097, 0x0077, 0x0057,
	0x0037, 0x00FB, 0x00DB, 0x00BB, 0x00FF, 0x00E3, 0x00C3, 0x00A3,
	0x0083, 0x0063, 0x0043, 0x0023, 0x0003, 0x01E3, 0x01C3, 0x01A3,
	0x0183, 0x0163, 0x0143, 0x0123, 0x0103
	};

static u8 OFDM_CONFIG[]	= {
	/* OFDM reg0x06[7:0]=0xFF: Enable power saving mode in RX */
	/* OFDM reg0x3C[4]=1'b1: Enable RX power saving mode */
	/* ofdm 0x3a = 0x7b ,(original : 0xfb) For ECS shielding room TP test */
	/* 0x00	*/
	0x10, 0x0F, 0x0A, 0x0C, 0x14, 0xFA, 0xFF, 0x50,
	0x00, 0x50, 0x00, 0x00, 0x00, 0x5C, 0x00, 0x00,
	/* 0x10	*/
	0x40, 0x00, 0x40, 0x00, 0x00, 0x00, 0xA8, 0x26,
	0x32, 0x33, 0x06, 0xA5, 0x6F, 0x55, 0xC8, 0xBB,
	/* 0x20	*/
	0x0A, 0xE1, 0x2C, 0x4A, 0x86, 0x83, 0x34, 0x00,
	0x4F, 0x24, 0x6F, 0xC2, 0x03, 0x40, 0x80, 0x00,
	/* 0x30	*/
	0xC0, 0xC1, 0x58, 0xF1, 0x00, 0xC4, 0x90, 0x3e,
	0xD8, 0x3C, 0x7B, 0x10, 0x10
	};

	/*---------------------------------------------------------------
	 *	Hardware IO
	 *	the code is ported from Windows source code
	 *---------------------------------------------------------------
	 */

void PlatformIOWrite1Byte(struct net_device *dev, u32 offset, u8 data)
{
	write_nic_byte(dev, offset, data);
	read_nic_byte(dev, offset); /* To make sure write operation is completed, 2005.11.09, by rcnjko. */
}

void PlatformIOWrite2Byte(struct net_device *dev, u32 offset, u16 data)
{
	write_nic_word(dev, offset, data);
	read_nic_word(dev, offset); /* To make sure write operation is completed, 2005.11.09, by rcnjko. */
}

u8 PlatformIORead1Byte(struct net_device *dev, u32 offset);

void PlatformIOWrite4Byte(struct net_device *dev, u32 offset, u32 data)
{
	if (offset == PhyAddr) {
	/* For Base Band configuration. */
		unsigned char	cmdByte;
		unsigned long	dataBytes;
		unsigned char	idx;
		u8		u1bTmp;

		cmdByte = (u8)(data & 0x000000ff);
		dataBytes = data>>8;

		/*
		 *	071010, rcnjko:
		 *	The critical section is only BB read/write race condition.
		 *	Assumption:
		 *	1. We assume NO one will access BB at DIRQL, otherwise, system will crash for
		 *	acquiring the spinlock in such context.
		 *	2. PlatformIOWrite4Byte() MUST NOT be recursive.
		 */
		/* NdisAcquireSpinLock( &(pDevice->IoSpinLock) ); */

		for (idx = 0; idx < 30; idx++) {
		/* Make sure command bit is clear before access it. */
			u1bTmp = PlatformIORead1Byte(dev, PhyAddr);
			if ((u1bTmp & BIT7) == 0)
				break;
			else
				mdelay(10);
		}

		for (idx = 0; idx < 3; idx++)
			PlatformIOWrite1Byte(dev, offset+1+idx, ((u8 *)&dataBytes)[idx]);

		write_nic_byte(dev, offset, cmdByte);

		/* NdisReleaseSpinLock( &(pDevice->IoSpinLock) ); */
	} else {
		write_nic_dword(dev, offset, data);
		read_nic_dword(dev, offset); /* To make sure write operation is completed, 2005.11.09, by rcnjko. */
	}
}

u8 PlatformIORead1Byte(struct net_device *dev, u32 offset)
{
	u8	data = 0;

	data = read_nic_byte(dev, offset);


	return data;
}

u16 PlatformIORead2Byte(struct net_device *dev, u32 offset)
{
	u16	data = 0;

	data = read_nic_word(dev, offset);


	return data;
}

u32 PlatformIORead4Byte(struct net_device *dev, u32 offset)
{
	u32	data = 0;

	data = read_nic_dword(dev, offset);


	return data;
}

void SetOutputEnableOfRfPins(struct net_device *dev)
{
	write_nic_word(dev, RFPinsEnable, 0x1bff);
}

static int HwHSSIThreeWire(struct net_device *dev,
			   u8 *pDataBuf,
			   u8 nDataBufBitCnt,
			   int bSI,
			   int bWrite)
{
	int	bResult = 1;
	u8	TryCnt;
	u8	u1bTmp;

	do {
		/* Check if WE and RE are cleared. */
		for (TryCnt = 0; TryCnt < TC_3W_POLL_MAX_TRY_CNT; TryCnt++) {
			u1bTmp = read_nic_byte(dev, SW_3W_CMD1);
			if ((u1bTmp & (SW_3W_CMD1_RE|SW_3W_CMD1_WE)) == 0)
				break;

			udelay(10);
		}
		if (TryCnt == TC_3W_POLL_MAX_TRY_CNT) {
			printk(KERN_ERR "rtl8187se: HwThreeWire(): CmdReg:"
			       " %#X RE|WE bits are not clear!!\n", u1bTmp);
			dump_stack();
			return 0;
		}

		/* RTL8187S HSSI Read/Write Function */
		u1bTmp = read_nic_byte(dev, RF_SW_CONFIG);

		if (bSI)
			u1bTmp |=   RF_SW_CFG_SI; /* reg08[1]=1 Serial Interface(SI) */

		else
			u1bTmp &= ~RF_SW_CFG_SI; /* reg08[1]=0 Parallel Interface(PI) */


		write_nic_byte(dev, RF_SW_CONFIG, u1bTmp);

		if (bSI) {
			/* jong: HW SI read must set reg84[3]=0. */
			u1bTmp = read_nic_byte(dev, RFPinsSelect);
			u1bTmp &= ~BIT3;
			write_nic_byte(dev, RFPinsSelect, u1bTmp);
		}
		/*  Fill up data buffer for write operation. */

		if (bWrite) {
			if (nDataBufBitCnt == 16) {
				write_nic_word(dev, SW_3W_DB0, *((u16 *)pDataBuf));
			} else if (nDataBufBitCnt == 64) {
			/* RTL8187S shouldn't enter this case */
				write_nic_dword(dev, SW_3W_DB0, *((u32 *)pDataBuf));
				write_nic_dword(dev, SW_3W_DB1, *((u32 *)(pDataBuf + 4)));
			} else {
				int idx;
				int ByteCnt = nDataBufBitCnt / 8;
								/* printk("%d\n",nDataBufBitCnt); */
				if ((nDataBufBitCnt % 8) != 0) {
					printk(KERN_ERR "rtl8187se: "
					       "HwThreeWire(): nDataBufBitCnt(%d)"
					       " should be multiple of 8!!!\n",
					       nDataBufBitCnt);
					dump_stack();
					nDataBufBitCnt += 8;
					nDataBufBitCnt &= ~7;
				}

			       if (nDataBufBitCnt > 64) {
					printk(KERN_ERR "rtl8187se: HwThreeWire():"
					       " nDataBufBitCnt(%d) should <= 64!!!\n",
					       nDataBufBitCnt);
					dump_stack();
					nDataBufBitCnt = 64;
				}

				for (idx = 0; idx < ByteCnt; idx++)
					write_nic_byte(dev, (SW_3W_DB0+idx), *(pDataBuf+idx));

			}
		} else {	/* read */
			if (bSI) {
				/* SI - reg274[3:0] : RF register's Address */
				write_nic_word(dev, SW_3W_DB0, *((u16 *)pDataBuf));
			} else {
				/*  PI - reg274[15:12] : RF register's Address */
				write_nic_word(dev, SW_3W_DB0, (*((u16 *)pDataBuf)) << 12);
			}
		}

		/* Set up command: WE or RE. */
		if (bWrite)
			write_nic_byte(dev, SW_3W_CMD1, SW_3W_CMD1_WE);

		else
			write_nic_byte(dev, SW_3W_CMD1, SW_3W_CMD1_RE);


		/* Check if DONE is set. */
		for (TryCnt = 0; TryCnt < TC_3W_POLL_MAX_TRY_CNT; TryCnt++) {
			u1bTmp = read_nic_byte(dev, SW_3W_CMD1);
			if ((u1bTmp & SW_3W_CMD1_DONE) != 0)
				break;

			udelay(10);
		}

		write_nic_byte(dev, SW_3W_CMD1, 0);

		/* Read back data for read operation. */
		if (bWrite == 0) {
			if (bSI) {
				/* Serial Interface : reg363_362[11:0] */
				*((u16 *)pDataBuf) = read_nic_word(dev, SI_DATA_READ) ;
			} else {
				/* Parallel Interface : reg361_360[11:0] */
				*((u16 *)pDataBuf) = read_nic_word(dev, PI_DATA_READ);
			}

			*((u16 *)pDataBuf) &= 0x0FFF;
		}

	} while (0);

	return bResult;
}

void RF_WriteReg(struct net_device *dev, u8 offset, u32 data)
{
	u32 data2Write;
	u8 len;

	/* Pure HW 3-wire. */
	data2Write = (data << 4) | (u32)(offset & 0x0f);
	len = 16;

	HwHSSIThreeWire(dev, (u8 *)(&data2Write), len, 1, 1);
}

u32 RF_ReadReg(struct net_device *dev, u8 offset)
{
	u32 data2Write;
	u8 wlen;
	u32 dataRead;

	data2Write = ((u32)(offset & 0x0f));
	wlen = 16;
	HwHSSIThreeWire(dev, (u8 *)(&data2Write), wlen, 1, 0);
	dataRead = data2Write;

	return dataRead;
}


/* by Owen on 04/07/14 for writing BB register successfully */
void WriteBBPortUchar(struct net_device *dev, u32 Data)
{
	/* u8	TimeoutCounter; */
	u8	RegisterContent;
	u8	UCharData;

	UCharData = (u8)((Data & 0x0000ff00) >> 8);
	PlatformIOWrite4Byte(dev, PhyAddr, Data);
	/* for(TimeoutCounter = 10; TimeoutCounter > 0; TimeoutCounter--) */
	{
		PlatformIOWrite4Byte(dev, PhyAddr, Data & 0xffffff7f);
		RegisterContent = PlatformIORead1Byte(dev, PhyDataR);
		/*if(UCharData == RegisterContent)	*/
		/*	break;	*/
	}
}

u8 ReadBBPortUchar(struct net_device *dev, u32 addr)
{
	/*u8	TimeoutCounter; */
	u8	RegisterContent;

	PlatformIOWrite4Byte(dev, PhyAddr, addr & 0xffffff7f);
	RegisterContent = PlatformIORead1Byte(dev, PhyDataR);

	return RegisterContent;
}
/*
 *	Description:
 *	Perform Antenna settings with antenna diversity on 87SE.
 *		Created by Roger, 2008.01.25.
 */
bool SetAntennaConfig87SE(struct net_device *dev,
			  u8   DefaultAnt, /* 0: Main, 1: Aux. */
			  bool bAntDiversity) /* 1:Enable, 0: Disable. */
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	bool   bAntennaSwitched = true;

	/* printk("SetAntennaConfig87SE(): DefaultAnt(%d), bAntDiversity(%d)\n", DefaultAnt, bAntDiversity); */

	/* Threshold for antenna diversity. */
	write_phy_cck(dev, 0x0c, 0x09); /* Reg0c : 09 */

	if (bAntDiversity) {	/*	Enable Antenna Diversity. */
		if (DefaultAnt == 1) {	/* aux antenna */

			/* Mac register, aux antenna */
			write_nic_byte(dev, ANTSEL, 0x00);

			/* Config CCK RX antenna. */
			write_phy_cck(dev, 0x11, 0xbb); /* Reg11 : bb */
			write_phy_cck(dev, 0x01, 0xc7); /* Reg01 : c7 */

			/* Config OFDM RX antenna. */
			write_phy_ofdm(dev, 0x0D, 0x54);	/* Reg0d : 54 */
			write_phy_ofdm(dev, 0x18, 0xb2);	/* Reg18 : b2 */
		} else { /*  use main antenna */
			/* Mac register, main antenna */
			write_nic_byte(dev, ANTSEL, 0x03);
			/* base band */
			/*  Config CCK RX antenna. */
			write_phy_cck(dev, 0x11, 0x9b); /* Reg11 : 9b */
			write_phy_cck(dev, 0x01, 0xc7); /* Reg01 : c7 */

			/* Config OFDM RX antenna. */
			write_phy_ofdm(dev, 0x0d, 0x5c);  /* Reg0d : 5c	*/
			write_phy_ofdm(dev, 0x18, 0xb2);  /* Reg18 : b2	*/
		}
	} else {
		/* Disable Antenna Diversity. */
		if (DefaultAnt == 1) { /* aux Antenna */
			/* Mac register, aux antenna */
			write_nic_byte(dev, ANTSEL, 0x00);

			/* Config CCK RX antenna. */
			write_phy_cck(dev, 0x11, 0xbb); /* Reg11 : bb */
			write_phy_cck(dev, 0x01, 0x47); /* Reg01 : 47 */

			/* Config OFDM RX antenna. */
			write_phy_ofdm(dev, 0x0D, 0x54);	/* Reg0d : 54 */
			write_phy_ofdm(dev, 0x18, 0x32);	/* Reg18 : 32 */
		} else { /* main Antenna */
			/* Mac register, main antenna */
			write_nic_byte(dev, ANTSEL, 0x03);

			/* Config CCK RX antenna.	*/
			write_phy_cck(dev, 0x11, 0x9b); /* Reg11 : 9b */
			write_phy_cck(dev, 0x01, 0x47); /* Reg01 : 47 */

			/* Config OFDM RX antenna. */
			write_phy_ofdm(dev, 0x0D, 0x5c); /* Reg0d : 5c */
			write_phy_ofdm(dev, 0x18, 0x32); /*Reg18 : 32 */
		}
	}
	priv->CurrAntennaIndex = DefaultAnt; /* Update default settings. */
	return	bAntennaSwitched;
}
/*
 *--------------------------------------------------------------
 *		Hardware Initialization.
 *		the code is ported from Windows source code
 *--------------------------------------------------------------
 */

void ZEBRA_Config_85BASIC_HardCode(struct net_device *dev)
{

	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	u32			i;
	u32	addr, data;
	u32	u4bRegOffset, u4bRegValue, u4bRF23, u4bRF24;
	u8			u1b24E;
	int d_cut = 0;


/*
 *===========================================================================
 *	87S_PCIE :: RADIOCFG.TXT
 *===========================================================================
 */


	/* Page1 : reg16-reg30 */
	RF_WriteReg(dev, 0x00, 0x013f);		mdelay(1); /* switch to page1 */
	u4bRF23 = RF_ReadReg(dev, 0x08);	mdelay(1);
	u4bRF24 = RF_ReadReg(dev, 0x09);	mdelay(1);

	if (u4bRF23 == 0x818 && u4bRF24 == 0x70C) {
		d_cut = 1;
		printk(KERN_INFO "rtl8187se: card type changed from C- to D-cut\n");
	}

	/* Page0 : reg0-reg15 */

	RF_WriteReg(dev, 0x00, 0x009f);		mdelay(1);/* 1	*/
	RF_WriteReg(dev, 0x01, 0x06e0);		mdelay(1);
	RF_WriteReg(dev, 0x02, 0x004d);		mdelay(1);/* 2	*/
	RF_WriteReg(dev, 0x03, 0x07f1);		mdelay(1);/* 3	*/
	RF_WriteReg(dev, 0x04, 0x0975);		mdelay(1);
	RF_WriteReg(dev, 0x05, 0x0c72);		mdelay(1);
	RF_WriteReg(dev, 0x06, 0x0ae6);		mdelay(1);
	RF_WriteReg(dev, 0x07, 0x00ca);		mdelay(1);
	RF_WriteReg(dev, 0x08, 0x0e1c);		mdelay(1);
	RF_WriteReg(dev, 0x09, 0x02f0);		mdelay(1);
	RF_WriteReg(dev, 0x0a, 0x09d0);		mdelay(1);
	RF_WriteReg(dev, 0x0b, 0x01ba);		mdelay(1);
	RF_WriteReg(dev, 0x0c, 0x0640);		mdelay(1);
	RF_WriteReg(dev, 0x0d, 0x08df);		mdelay(1);
	RF_WriteReg(dev, 0x0e, 0x0020);		mdelay(1);
	RF_WriteReg(dev, 0x0f, 0x0990);		mdelay(1);

	/*  Page1 : reg16-reg30 */
	RF_WriteReg(dev, 0x00, 0x013f);		mdelay(1);
	RF_WriteReg(dev, 0x03, 0x0806);		mdelay(1);
	RF_WriteReg(dev, 0x04, 0x03a7);		mdelay(1);
	RF_WriteReg(dev, 0x05, 0x059b);		mdelay(1);
	RF_WriteReg(dev, 0x06, 0x0081);		mdelay(1);
	RF_WriteReg(dev, 0x07, 0x01A0);		mdelay(1);
/* Don't write RF23/RF24 to make a difference between 87S C cut and D cut. asked by SD3 stevenl. */
	RF_WriteReg(dev, 0x0a, 0x0001);		mdelay(1);
	RF_WriteReg(dev, 0x0b, 0x0418);		mdelay(1);

	if (d_cut) {
		RF_WriteReg(dev, 0x0c, 0x0fbe);		mdelay(1);
		RF_WriteReg(dev, 0x0d, 0x0008);		mdelay(1);
		RF_WriteReg(dev, 0x0e, 0x0807);		mdelay(1); /* RX LO buffer */
	} else {
		RF_WriteReg(dev, 0x0c, 0x0fbe);		mdelay(1);
		RF_WriteReg(dev, 0x0d, 0x0008);		mdelay(1);
		RF_WriteReg(dev, 0x0e, 0x0806);		mdelay(1); /* RX LO buffer */
	}

	RF_WriteReg(dev, 0x0f, 0x0acc);		mdelay(1);
	RF_WriteReg(dev, 0x00, 0x01d7);		mdelay(1); /* 6 */
	RF_WriteReg(dev, 0x03, 0x0e00);		mdelay(1);
	RF_WriteReg(dev, 0x04, 0x0e50);		mdelay(1);

	for (i = 0; i <= 36; i++) {
		RF_WriteReg(dev, 0x01, i);		mdelay(1);
		RF_WriteReg(dev, 0x02, ZEBRA_RF_RX_GAIN_TABLE[i]); mdelay(1);
	}

	RF_WriteReg(dev, 0x05, 0x0203);		mdelay(1); /* 203, 343 */
	RF_WriteReg(dev, 0x06, 0x0200);		mdelay(1); /* 400 */
	RF_WriteReg(dev, 0x00, 0x0137);		mdelay(1); /* switch to reg16-reg30, and HSSI disable 137 */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd */

	RF_WriteReg(dev, 0x0d, 0x0008);		mdelay(1); /* Z4 synthesizer loop filter setting, 392 */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd */

	RF_WriteReg(dev, 0x00, 0x0037);		mdelay(1); /* switch to reg0-reg15, and HSSI disable */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd	*/

	RF_WriteReg(dev, 0x04, 0x0160);		mdelay(1); /* CBC on, Tx Rx disable, High gain */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd	*/

	RF_WriteReg(dev, 0x07, 0x0080);		mdelay(1); /* Z4 setted channel 1 */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd	*/

	RF_WriteReg(dev, 0x02, 0x088D);		mdelay(1); /* LC calibration */
	mdelay(200); /* Deay 200 ms. */		/* 0xfd	*/
	mdelay(10);  /* Deay 10 ms. */		/* 0xfd	*/
	mdelay(10);  /* Deay 10 ms. */		/* 0xfd	*/

	RF_WriteReg(dev, 0x00, 0x0137);		mdelay(1); /* switch to reg16-reg30 137, and HSSI disable 137 */
	mdelay(10); /* Deay 10 ms. */		/* 0xfd	*/

	RF_WriteReg(dev, 0x07, 0x0000);		mdelay(1);
	RF_WriteReg(dev, 0x07, 0x0180);		mdelay(1);
	RF_WriteReg(dev, 0x07, 0x0220);		mdelay(1);
	RF_WriteReg(dev, 0x07, 0x03E0);		mdelay(1);

	/* DAC calibration off 20070702	*/
	RF_WriteReg(dev, 0x06, 0x00c1);		mdelay(1);
	RF_WriteReg(dev, 0x0a, 0x0001);		mdelay(1);
	/* For crystal calibration, added by Roger, 2007.12.11. */
	if (priv->bXtalCalibration) { /* reg 30.	*/
	 /*
 	  *  enable crystal calibration.
	  *		RF Reg[30], (1)Xin:[12:9], Xout:[8:5],  addr[4:0].
	  *		(2)PA Pwr delay timer[15:14], default: 2.4us, set BIT15=0
	  *		(3)RF signal on/off when calibration[13], default: on, set BIT13=0.
	  *		So we should minus 4 BITs offset. 
	  */
		RF_WriteReg(dev, 0x0f, (priv->XtalCal_Xin<<5) | (priv->XtalCal_Xout<<1) | BIT11 | BIT9); mdelay(1);
		printk("ZEBRA_Config_85BASIC_HardCode(): (%02x)\n",
		      (priv->XtalCal_Xin<<5) | (priv->XtalCal_Xout<<1) | BIT11 | BIT9);
	} else {
		/* using default value. Xin=6, Xout=6.	*/
		RF_WriteReg(dev, 0x0f, 0x0acc);		mdelay(1);
	}

	RF_WriteReg(dev, 0x00, 0x00bf);		mdelay(1); /* switch to reg0-reg15, and HSSI enable */
	RF_WriteReg(dev, 0x0d, 0x08df);		mdelay(1); /* Rx BB start calibration, 00c//+edward */
	RF_WriteReg(dev, 0x02, 0x004d);		mdelay(1); /* temperature meter off */
	RF_WriteReg(dev, 0x04, 0x0975);		mdelay(1); /* Rx mode */
	mdelay(10);	/* Deay 10 ms.*/	/* 0xfe	*/
	mdelay(10);	/* Deay 10 ms.*/	/* 0xfe	*/
	mdelay(10);	/* Deay 10 ms.*/	/* 0xfe	*/
	RF_WriteReg(dev, 0x00, 0x0197);		mdelay(1); /* Rx mode*/	/*+edward */
	RF_WriteReg(dev, 0x05, 0x05ab);		mdelay(1); /* Rx mode*/	/*+edward */
	RF_WriteReg(dev, 0x00, 0x009f);		mdelay(1); /* Rx mode*/	/*+edward */
	RF_WriteReg(dev, 0x01, 0x0000);		mdelay(1); /* Rx mode*/	/*+edward */
	RF_WriteReg(dev, 0x02, 0x0000);		mdelay(1); /* Rx mode*/	/*+edward */
	/* power save parameters. */
	u1b24E = read_nic_byte(dev, 0x24E);
	write_nic_byte(dev, 0x24E, (u1b24E & (~(BIT5|BIT6))));

	/*=============================================================================
	 *
	 *===========================================================================
	 * CCKCONF.TXT
	 *===========================================================================
	 *
	 *	[POWER SAVE] Power Saving Parameters by jong. 2007-11-27
	 *	CCK reg0x00[7]=1'b1 :power saving for TX (default)
	 *	CCK reg0x00[6]=1'b1: power saving for RX (default)
	 *	CCK reg0x06[4]=1'b1: turn off channel estimation related circuits if not doing channel estimation.
	 *	CCK reg0x06[3]=1'b1: turn off unused circuits before cca = 1
	 *	CCK reg0x06[2]=1'b1: turn off cck's circuit if macrst =0
	 */

	write_phy_cck(dev, 0x00, 0xc8);
	write_phy_cck(dev, 0x06, 0x1c);
	write_phy_cck(dev, 0x10, 0x78);
	write_phy_cck(dev, 0x2e, 0xd0);
	write_phy_cck(dev, 0x2f, 0x06);
	write_phy_cck(dev, 0x01, 0x46);

	/* power control */
	write_nic_byte(dev, CCK_TXAGC, 0x10);
	write_nic_byte(dev, OFDM_TXAGC, 0x1B);
	write_nic_byte(dev, ANTSEL, 0x03);


	/*
	 *===========================================================================
	 *	AGC.txt
	 *===========================================================================
	 */

	write_phy_ofdm(dev, 0x00, 0x12);

	for (i = 0; i < 128; i++) {

		data = ZEBRA_AGC[i+1];
		data = data << 8;
		data = data | 0x0000008F;

		addr = i + 0x80; /* enable writing AGC table */
		addr = addr << 8;
		addr = addr | 0x0000008E;

		WriteBBPortUchar(dev, data);
		WriteBBPortUchar(dev, addr);
		WriteBBPortUchar(dev, 0x0000008E);
	}

	PlatformIOWrite4Byte(dev, PhyAddr, 0x00001080);	/* Annie, 2006-05-05 */

	/*
	 *===========================================================================
	 *
	 *===========================================================================
	 * OFDMCONF.TXT
	 *===========================================================================
	 */

	for (i = 0; i < 60; i++) {
		u4bRegOffset = i;
		u4bRegValue = OFDM_CONFIG[i];

		WriteBBPortUchar(dev,
				(0x00000080 |
				(u4bRegOffset & 0x7f) |
				((u4bRegValue & 0xff) << 8)));
	}

	/*
	 *===========================================================================
	 * by amy for antenna
	 *===========================================================================
	 */
	/* Config Sw/Hw  Combinational Antenna Diversity. Added by Roger, 2008.02.26.	*/
	SetAntennaConfig87SE(dev, priv->bDefaultAntenna1, priv->bSwAntennaDiverity);
}


void UpdateInitialGain(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);

	/* lzm add 080826 */
	if (priv->eRFPowerState != eRfOn) {
		/*	Don't access BB/RF under disable PLL situation.
		 *	RT_TRACE(COMP_DIG, DBG_LOUD, ("UpdateInitialGain - pHalData->eRFPowerState!=eRfOn\n"));
		 *	Back to the original state
		 */
		priv->InitialGain = priv->InitialGainBackUp;
		return;
	}

	switch (priv->InitialGain) {
	case 1: /* m861dBm */
		write_phy_ofdm(dev, 0x17, 0x26);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x86);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfa);	mdelay(1);
		break;

	case 2: /* m862dBm */
		write_phy_ofdm(dev, 0x17, 0x36);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x86);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfa);	mdelay(1);
		break;

	case 3: /* m863dBm */
		write_phy_ofdm(dev, 0x17, 0x36);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x86);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfb);	mdelay(1);
		break;

	case 4: /* m864dBm */
		write_phy_ofdm(dev, 0x17, 0x46);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x86);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfb);	mdelay(1);
		break;

	case 5: /* m82dBm */
		write_phy_ofdm(dev, 0x17, 0x46);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x96);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfb);	mdelay(1);
		break;

	case 6: /* m78dBm */
		write_phy_ofdm(dev, 0x17, 0x56);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x96);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfc);	mdelay(1);
		break;

	case 7: /* m74dBm */
		write_phy_ofdm(dev, 0x17, 0x56);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0xa6);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfc);	mdelay(1);
		break;

	case 8:
		write_phy_ofdm(dev, 0x17, 0x66);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0xb6);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfc);	mdelay(1);
		break;

	default: /* MP */
		write_phy_ofdm(dev, 0x17, 0x26);	mdelay(1);
		write_phy_ofdm(dev, 0x24, 0x86);	mdelay(1);
		write_phy_ofdm(dev, 0x05, 0xfa);	mdelay(1);
		break;
	}
}
/*
 *	Description:
 *		Tx Power tracking mechanism routine on 87SE.
 *	Created by Roger, 2007.12.11.
 */
void InitTxPwrTracking87SE(struct net_device *dev)
{
	u32	u4bRfReg;

	u4bRfReg = RF_ReadReg(dev, 0x02);

	/* Enable Thermal meter indication.	*/
	RF_WriteReg(dev, 0x02, u4bRfReg|PWR_METER_EN);			mdelay(1);
}

void PhyConfig8185(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
		write_nic_dword(dev, RCR, priv->ReceiveConfig);
	   priv->RFProgType = read_nic_byte(dev, CONFIG4) & 0x03;
	/*  RF config */
	ZEBRA_Config_85BASIC_HardCode(dev);
	/* Set default initial gain state to 4, approved by SD3 DZ, by Bruce, 2007-06-06. */
	if (priv->bDigMechanism) {
		if (priv->InitialGain == 0)
			priv->InitialGain = 4;
	}

	/*
	 *	Enable thermal meter indication to implement TxPower tracking on 87SE.
	 *	We initialize thermal meter here to avoid unsuccessful configuration.
	 *	Added by Roger, 2007.12.11.
	 */
	if (priv->bTxPowerTrack)
		InitTxPwrTracking87SE(dev);

	priv->InitialGainBackUp = priv->InitialGain;
	UpdateInitialGain(dev);

	return;
}

void HwConfigureRTL8185(struct net_device *dev)
{
	/* RTL8185_TODO: Determine Retrylimit, TxAGC, AutoRateFallback control. */
	u8 bUNIVERSAL_CONTROL_RL = 0;
	u8 bUNIVERSAL_CONTROL_AGC = 1;
	u8 bUNIVERSAL_CONTROL_ANT = 1;
	u8 bAUTO_RATE_FALLBACK_CTL = 1;
	u8 val8;
	write_nic_word(dev, BRSR, 0x0fff);
	/* Retry limit */
	val8 = read_nic_byte(dev, CW_CONF);

	if (bUNIVERSAL_CONTROL_RL)
		val8 = val8 & 0xfd;
	else
		val8 = val8 | 0x02;

	write_nic_byte(dev, CW_CONF, val8);

	/* Tx AGC */
	val8 = read_nic_byte(dev, TXAGC_CTL);
	if (bUNIVERSAL_CONTROL_AGC) {
		write_nic_byte(dev, CCK_TXAGC, 128);
		write_nic_byte(dev, OFDM_TXAGC, 128);
		val8 = val8 & 0xfe;
	} else {
		val8 = val8 | 0x01 ;
	}


	write_nic_byte(dev, TXAGC_CTL, val8);

	/* Tx Antenna including Feedback control */
	val8 = read_nic_byte(dev, TXAGC_CTL);

	if (bUNIVERSAL_CONTROL_ANT) {
		write_nic_byte(dev, ANTSEL, 0x00);
		val8 = val8 & 0xfd;
	} else {
		val8 = val8 & (val8|0x02); /* xiong-2006-11-15 */
	}

	write_nic_byte(dev, TXAGC_CTL, val8);

	/* Auto Rate fallback control	*/
	val8 = read_nic_byte(dev, RATE_FALLBACK);
	val8 &= 0x7c;
	if (bAUTO_RATE_FALLBACK_CTL) {
		val8 |= RATE_FALLBACK_CTL_ENABLE | RATE_FALLBACK_CTL_AUTO_STEP1;

		/* <RJ_TODO_8185B> We shall set up the ARFR according to user's setting. */
		PlatformIOWrite2Byte(dev, ARFR, 0x0fff); /* set 1M ~ 54Mbps. */
	}
	write_nic_byte(dev, RATE_FALLBACK, val8);
}

static void MacConfig_85BASIC_HardCode(struct net_device *dev)
{
	/*
	 *==========================================================================
	 * MACREG.TXT
	 *==========================================================================
	 */
	int nLinesRead = 0;
	u32 u4bRegOffset, u4bRegValue, u4bPageIndex = 0;
	int i;

	nLinesRead = sizeof(MAC_REG_TABLE)/2;

	for (i = 0; i < nLinesRead; i++) { /* nLinesRead=101 */
		u4bRegOffset = MAC_REG_TABLE[i][0];
		u4bRegValue = MAC_REG_TABLE[i][1];

				if (u4bRegOffset == 0x5e)
					u4bPageIndex = u4bRegValue;
				else
					u4bRegOffset |= (u4bPageIndex << 8);

		write_nic_byte(dev, u4bRegOffset, (u8)u4bRegValue);
	}
	/* ============================================================================ */
}

static void MacConfig_85BASIC(struct net_device *dev)
{

	u8			u1DA;
	MacConfig_85BASIC_HardCode(dev);

	/* ============================================================================ */

	/* Follow TID_AC_MAP of WMac. */
	write_nic_word(dev, TID_AC_MAP, 0xfa50);

	/* Interrupt Migration, Jong suggested we use set 0x0000 first, 2005.12.14, by rcnjko. */
	write_nic_word(dev, IntMig, 0x0000);

	/* Prevent TPC to cause CRC error. Added by Annie, 2006-06-10. */
	PlatformIOWrite4Byte(dev, 0x1F0, 0x00000000);
	PlatformIOWrite4Byte(dev, 0x1F4, 0x00000000);
	PlatformIOWrite1Byte(dev, 0x1F8, 0x00);

	/* Asked for by SD3 CM Lin, 2006.06.27, by rcnjko. */
	/* power save parameter based on "87SE power save parameters 20071127.doc", as follow. */

	/* Enable DA10 TX power saving */
	u1DA = read_nic_byte(dev, PHYPR);
	write_nic_byte(dev, PHYPR, (u1DA | BIT2));

	/* POWER: */
	write_nic_word(dev, 0x360, 0x1000);
	write_nic_word(dev, 0x362, 0x1000);

	/* AFE. */
	write_nic_word(dev, 0x370, 0x0560);
	write_nic_word(dev, 0x372, 0x0560);
	write_nic_word(dev, 0x374, 0x0DA4);
	write_nic_word(dev, 0x376, 0x0DA4);
	write_nic_word(dev, 0x378, 0x0560);
	write_nic_word(dev, 0x37A, 0x0560);
	write_nic_word(dev, 0x37C, 0x00EC);
	write_nic_word(dev, 0x37E, 0x00EC); /* +edward */
	write_nic_byte(dev, 0x24E, 0x01);
}

u8 GetSupportedWirelessMode8185(struct net_device *dev)
{
	u8 btSupportedWirelessMode = 0;

	btSupportedWirelessMode = (WIRELESS_MODE_B | WIRELESS_MODE_G);
	return btSupportedWirelessMode;
}

void ActUpdateChannelAccessSetting(struct net_device *dev,
				   WIRELESS_MODE WirelessMode,
				   PCHANNEL_ACCESS_SETTING ChnlAccessSetting)
{
	struct		r8180_priv *priv = ieee80211_priv(dev);
	struct		ieee80211_device *ieee = priv->ieee80211;
	AC_CODING	eACI;
	AC_PARAM	AcParam;
	u8		bFollowLegacySetting = 0;
	u8		u1bAIFS;

	/*
	 *	<RJ_TODO_8185B>
	 *	TODO: We still don't know how to set up these registers, just follow WMAC to
	 *	verify 8185B FPAG.
	 *
	 *	<RJ_TODO_8185B>
	 *	Jong said CWmin/CWmax register are not functional in 8185B,
	 *	so we shall fill channel access realted register into AC parameter registers,
	 *	even in nQBss.
	 */
	ChnlAccessSetting->SIFS_Timer = 0x22; /* Suggested by Jong, 2005.12.08. */
	ChnlAccessSetting->DIFS_Timer = 0x1C; /* 2006.06.02, by rcnjko. */
	ChnlAccessSetting->SlotTimeTimer = 9; /* 2006.06.02, by rcnjko. */
	ChnlAccessSetting->EIFS_Timer = 0x5B; /* Suggested by wcchu, it is the default value of EIFS register, 2005.12.08. */
	ChnlAccessSetting->CWminIndex = 3; /* 2006.06.02, by rcnjko. */
	ChnlAccessSetting->CWmaxIndex = 7; /* 2006.06.02, by rcnjko. */

	write_nic_byte(dev, SIFS, ChnlAccessSetting->SIFS_Timer);
	write_nic_byte(dev, SLOT, ChnlAccessSetting->SlotTimeTimer); /* Rewrited from directly use PlatformEFIOWrite1Byte(), by Annie, 2006-03-29. */

	u1bAIFS = aSifsTime + (2 * ChnlAccessSetting->SlotTimeTimer);

	write_nic_byte(dev, EIFS, ChnlAccessSetting->EIFS_Timer);

	write_nic_byte(dev, AckTimeOutReg, 0x5B); /* <RJ_EXPR_QOS> Suggested by wcchu, it is the default value of EIFS register, 2005.12.08. */

	{ /* Legacy 802.11. */
		bFollowLegacySetting = 1;

	}

	/* this setting is copied from rtl8187B.  xiong-2006-11-13 */
	if (bFollowLegacySetting) {

		/*
		 *	Follow 802.11 seeting to AC parameter, all AC shall use the same parameter.
		 *	2005.12.01, by rcnjko.
		 */
		AcParam.longData = 0;
		AcParam.f.AciAifsn.f.AIFSN = 2; /* Follow 802.11 DIFS.	*/
		AcParam.f.AciAifsn.f.ACM = 0;
		AcParam.f.Ecw.f.ECWmin = ChnlAccessSetting->CWminIndex; /* Follow 802.11 CWmin. */
		AcParam.f.Ecw.f.ECWmax = ChnlAccessSetting->CWmaxIndex; /* Follow 802.11 CWmax. */
		AcParam.f.TXOPLimit = 0;

		/* lzm reserved 080826 */
		/* For turbo mode setting. port from 87B by Isaiah 2008-08-01 */
		if (ieee->current_network.Turbo_Enable == 1)
			AcParam.f.TXOPLimit = 0x01FF;
		/* For 87SE with Intel 4965  Ad-Hoc mode have poor throughput (19MB) */
		if (ieee->iw_mode == IW_MODE_ADHOC)
			AcParam.f.TXOPLimit = 0x0020;

		for (eACI = 0; eACI < AC_MAX; eACI++) {
			AcParam.f.AciAifsn.f.ACI = (u8)eACI;
			{
				PAC_PARAM	pAcParam = (PAC_PARAM)(&AcParam);
				AC_CODING	eACI;
				u8		u1bAIFS;
				u32		u4bAcParam;

				/*  Retrieve paramters to update. */
				eACI = pAcParam->f.AciAifsn.f.ACI;
				u1bAIFS = pAcParam->f.AciAifsn.f.AIFSN * ChnlAccessSetting->SlotTimeTimer + aSifsTime;
				u4bAcParam = ((((u32)(pAcParam->f.TXOPLimit)) << AC_PARAM_TXOP_LIMIT_OFFSET)	|
						(((u32)(pAcParam->f.Ecw.f.ECWmax)) << AC_PARAM_ECW_MAX_OFFSET)	|
						(((u32)(pAcParam->f.Ecw.f.ECWmin)) << AC_PARAM_ECW_MIN_OFFSET)	|
						(((u32)u1bAIFS) << AC_PARAM_AIFS_OFFSET));

				switch (eACI) {
				case AC1_BK:
					/* write_nic_dword(dev, AC_BK_PARAM, u4bAcParam); */
					break;

				case AC0_BE:
					/* write_nic_dword(dev, AC_BK_PARAM, u4bAcParam); */
					break;

				case AC2_VI:
					/* write_nic_dword(dev, AC_BK_PARAM, u4bAcParam); */
					break;

				case AC3_VO:
					/* write_nic_dword(dev, AC_BK_PARAM, u4bAcParam); */
					break;

				default:
					DMESGW("SetHwReg8185(): invalid ACI: %d !\n", eACI);
					break;
				}

				/* Cehck ACM bit. */
				/* If it is set, immediately set ACM control bit to downgrading AC for passing WMM testplan. Annie, 2005-12-13.	*/
				{
					PACI_AIFSN	pAciAifsn = (PACI_AIFSN)(&pAcParam->f.AciAifsn);
					AC_CODING	eACI = pAciAifsn->f.ACI;

					/*for 8187B AsynIORead issue */
					u8	AcmCtrl = 0;
					if (pAciAifsn->f.ACM) {
						/* ACM bit is 1. */
						switch (eACI) {
						case AC0_BE:
							AcmCtrl |= (BEQ_ACM_EN|BEQ_ACM_CTL|ACM_HW_EN); /* or 0x21 */
							break;

						case AC2_VI:
							AcmCtrl |= (VIQ_ACM_EN|VIQ_ACM_CTL|ACM_HW_EN); /* or 0x42 */
							break;

						case AC3_VO:
							AcmCtrl |= (VOQ_ACM_EN|VOQ_ACM_CTL|ACM_HW_EN); /* or 0x84 */
							break;

						default:
							DMESGW("SetHwReg8185(): [HW_VAR_ACM_CTRL] ACM set failed: eACI is %d\n", eACI);
							break;
						}
					} else {
						/* ACM bit is 0. */
						switch (eACI) {
						case AC0_BE:
							AcmCtrl &= ((~BEQ_ACM_EN) & (~BEQ_ACM_CTL) & (~ACM_HW_EN)); /* and 0xDE */
							break;

						case AC2_VI:
							AcmCtrl &= ((~VIQ_ACM_EN) & (~VIQ_ACM_CTL) & (~ACM_HW_EN)); /* and 0xBD */
							break;

						case AC3_VO:
							AcmCtrl &= ((~VOQ_ACM_EN) & (~VOQ_ACM_CTL) & (~ACM_HW_EN)); /* and 0x7B */
							break;

						default:
							break;
						}
					}
					write_nic_byte(dev, ACM_CONTROL, 0);
				}
			}
		}
	}
}

void ActSetWirelessMode8185(struct net_device *dev, u8 btWirelessMode)
{
	struct  r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	struct  ieee80211_device *ieee = priv->ieee80211;
	u8	btSupportedWirelessMode = GetSupportedWirelessMode8185(dev);

	if ((btWirelessMode & btSupportedWirelessMode) == 0)	{
		/* Don't switch to unsupported wireless mode, 2006.02.15, by rcnjko. */
		DMESGW("ActSetWirelessMode8185(): WirelessMode(%d) is not supported (%d)!\n",
			btWirelessMode, btSupportedWirelessMode);
		return;
	}

	/* 1. Assign wireless mode to switch if necessary. */
	if (btWirelessMode == WIRELESS_MODE_AUTO) {
		if ((btSupportedWirelessMode & WIRELESS_MODE_A)) {
			btWirelessMode = WIRELESS_MODE_A;
		} else if (btSupportedWirelessMode & WIRELESS_MODE_G) {
				btWirelessMode = WIRELESS_MODE_G;

		} else if ((btSupportedWirelessMode & WIRELESS_MODE_B))	{
				btWirelessMode = WIRELESS_MODE_B;
		} else {
			DMESGW("ActSetWirelessMode8185(): No valid wireless mode supported, btSupportedWirelessMode(%x)!!!\n",
			       btSupportedWirelessMode);
			btWirelessMode = WIRELESS_MODE_B;
		}
	}

	/* 
 	 * 2. Swtich band: RF or BB specific actions,
	 * for example, refresh tables in omc8255, or change initial gain if necessary.
	 * Nothing to do for Zebra to switch band.
	 * Update current wireless mode if we switch to specified band successfully. 
	 */

	ieee->mode = (WIRELESS_MODE)btWirelessMode;

	/* 3. Change related setting. */
	if( ieee->mode == WIRELESS_MODE_A ) {
		DMESG("WIRELESS_MODE_A\n");
	} else if( ieee->mode == WIRELESS_MODE_B ) {
		DMESG("WIRELESS_MODE_B\n");
	} else if( ieee->mode == WIRELESS_MODE_G ) {
		DMESG("WIRELESS_MODE_G\n");
	}
	ActUpdateChannelAccessSetting( dev, ieee->mode, &priv->ChannelAccessSetting);
}

void rtl8185b_irq_enable(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);

	priv->irq_enabled = 1;
	write_nic_dword(dev, IMR, priv->IntrMask);
}

void DrvIFIndicateDisassociation(struct net_device *dev, u16 reason)
{
		/* nothing is needed after disassociation request. */
}

void MgntDisconnectIBSS(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	u8 i;

	DrvIFIndicateDisassociation(dev, unspec_reason);

	for (i = 0; i < 6 ; i++)
		priv->ieee80211->current_network.bssid[i] = 0x55;


	priv->ieee80211->state = IEEE80211_NOLINK;
	/*
	 *	Stop Beacon.
	 *
	 *	Vista add a Adhoc profile, HW radio off until OID_DOT11_RESET_REQUEST
	 *	Driver would set MSR=NO_LINK, then HW Radio ON, MgntQueue Stuck.
	 *	Because Bcn DMA isn't complete, mgnt queue would stuck until Bcn packet send.
	 *
	 *	Disable Beacon Queue Own bit, suggested by jong	
	 */
	ieee80211_stop_send_beacons(priv->ieee80211);

	priv->ieee80211->link_change(dev);
	notify_wx_assoc_event(priv->ieee80211);
}

void MlmeDisassociateRequest(struct net_device *dev, u8 *asSta, u8 asRsn)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	u8 i;

	SendDisassociation(priv->ieee80211, asSta, asRsn);

	if (memcmp(priv->ieee80211->current_network.bssid, asSta, 6) == 0) {
		/* ShuChen TODO: change media status. */
		/* ShuChen TODO: What to do when disassociate. */
		DrvIFIndicateDisassociation(dev, unspec_reason);

		for (i = 0; i < 6; i++)
			priv->ieee80211->current_network.bssid[i] = 0x22;

		ieee80211_disassociate(priv->ieee80211);
	}
}

void MgntDisconnectAP(struct net_device *dev, u8 asRsn)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);

	/*
	 * Commented out by rcnjko, 2005.01.27:
	 * I move SecClearAllKeys() to MgntActSet_802_11_DISASSOCIATE().
	 *
	 *	2004/09/15, kcwu, the key should be cleared, or the new handshaking will not success
	 *
	 *	In WPA WPA2 need to Clear all key ... because new key will set after new handshaking.
	 *	2004.10.11, by rcnjko. 
	 */
	MlmeDisassociateRequest(dev, priv->ieee80211->current_network.bssid, asRsn);

	priv->ieee80211->state = IEEE80211_NOLINK;
}

bool MgntDisconnect(struct net_device *dev, u8 asRsn)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	/*
	 *	Schedule an workitem to wake up for ps mode, 070109, by rcnjko.
	 */

	if (IS_DOT11D_ENABLE(priv->ieee80211))
		Dot11d_Reset(priv->ieee80211);
	/* In adhoc mode, update beacon frame. */
	if (priv->ieee80211->state == IEEE80211_LINKED)	{
		if (priv->ieee80211->iw_mode == IW_MODE_ADHOC)
			MgntDisconnectIBSS(dev);

		if (priv->ieee80211->iw_mode == IW_MODE_INFRA) {
			/*
 			 * 	We clear key here instead of MgntDisconnectAP() because that
			 *	MgntActSet_802_11_DISASSOCIATE() is an interface called by OS,
			 *	e.g. OID_802_11_DISASSOCIATE in Windows while as MgntDisconnectAP() is
			 *	used to handle disassociation related things to AP, e.g. send Disassoc
			 *	frame to AP.  2005.01.27, by rcnjko. 
			 */
			MgntDisconnectAP(dev, asRsn);
		}
		/* Indicate Disconnect, 2005.02.23, by rcnjko.	*/
	}
	return true;
}
/*
 *	Description:
 *		Chang RF Power State.
 *		Note that, only MgntActSet_RF_State() is allowed to set HW_VAR_RF_STATE.
 *
 *	Assumption:
 *		PASSIVE LEVEL.
 */
bool SetRFPowerState(struct net_device *dev, RT_RF_POWER_STATE eRFPowerState)
{
	struct	r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	bool	bResult = false;

	if (eRFPowerState == priv->eRFPowerState)
		return bResult;

	bResult = SetZebraRFPowerState8185(dev, eRFPowerState);

	return bResult;
}

void HalEnableRx8185Dummy(struct net_device *dev)
{
}

void HalDisableRx8185Dummy(struct net_device *dev)
{
}

bool MgntActSet_RF_State(struct net_device *dev, RT_RF_POWER_STATE StateToSet, u32 ChangeSource)
{
	struct	r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	bool	bActionAllowed = false;
	bool	bConnectBySSID = false;
	RT_RF_POWER_STATE rtState;
	u16	RFWaitCounter = 0;
	unsigned long flag;
	/*
	 *	Prevent the race condition of RF state change. By Bruce, 2007-11-28.
	 *	Only one thread can change the RF state at one time, and others should wait to be executed.
	 */
	while (true) {
		spin_lock_irqsave(&priv->rf_ps_lock, flag);
		if (priv->RFChangeInProgress) {
			spin_unlock_irqrestore(&priv->rf_ps_lock, flag);
			/*  Set RF after the previous action is done.	*/
			while (priv->RFChangeInProgress) {
				RFWaitCounter++;
				udelay(1000); /* 1 ms	*/

				/* Wait too long, return FALSE to avoid to be stuck here. */
				if (RFWaitCounter > 1000) { /* 1sec */
					printk("MgntActSet_RF_State(): Wait too long to set RF\n");
					/* TODO: Reset RF state? */
					return false;
				}
			}
		} else {
			priv->RFChangeInProgress = true;
			spin_unlock_irqrestore(&priv->rf_ps_lock, flag);
			break;
		}
	}
	rtState = priv->eRFPowerState;

	switch (StateToSet) {
	case eRfOn:
		/*
		 *	Turn On RF no matter the IPS setting because we need to update the RF state to Ndis under Vista, or
		 *	the Windows does not allow the driver to perform site survey any more. By Bruce, 2007-10-02.
		 */
		priv->RfOffReason &= (~ChangeSource);

		if (!priv->RfOffReason)	{
			priv->RfOffReason = 0;
			bActionAllowed = true;

			if (rtState == eRfOff && ChangeSource >= RF_CHANGE_BY_HW && !priv->bInHctTest)
				bConnectBySSID = true;

		} else
			;
		break;

	case eRfOff:
		 /* 070125, rcnjko: we always keep connected in AP mode. */

		if (priv->RfOffReason > RF_CHANGE_BY_IPS) {
			/*
			 *	060808, Annie:
			 *	Disconnect to current BSS when radio off. Asked by QuanTa.
			 *
			 *	Calling MgntDisconnect() instead of MgntActSet_802_11_DISASSOCIATE(),
			 *	because we do NOT need to set ssid to dummy ones.
			 */
			MgntDisconnect(dev, disas_lv_ss);
			/* Clear content of bssDesc[] and bssDesc4Query[] to avoid reporting old bss to UI. */
		}

		priv->RfOffReason |= ChangeSource;
		bActionAllowed = true;
		break;
	case eRfSleep:
		priv->RfOffReason |= ChangeSource;
		bActionAllowed = true;
		break;
	default:
		break;
	}

	if (bActionAllowed) {
		/* Config HW to the specified mode. */
		SetRFPowerState(dev, StateToSet);

		/* Turn on RF.	*/
		if (StateToSet == eRfOn) {
			HalEnableRx8185Dummy(dev);
			if (bConnectBySSID) {
				/* by amy not supported	*/
			}
		}
		/* Turn off RF.	*/
		else if (StateToSet == eRfOff)
			HalDisableRx8185Dummy(dev);

	}

	/* Release RF spinlock	*/
	spin_lock_irqsave(&priv->rf_ps_lock, flag);
	priv->RFChangeInProgress = false;
	spin_unlock_irqrestore(&priv->rf_ps_lock, flag);
	return bActionAllowed;
}

void InactivePowerSave(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	/*
	 *	This flag "bSwRfProcessing", indicates the status of IPS procedure, should be set if the IPS workitem
	 *	is really scheduled.
	 *	The old code, sets this flag before scheduling the IPS workitem and however, at the same time the
	 *	previous IPS workitem did not end yet, fails to schedule the current workitem. Thus, bSwRfProcessing
	 *	blocks the IPS procedure of switching RF.
	 */
	priv->bSwRfProcessing = true;

	MgntActSet_RF_State(dev, priv->eInactivePowerState, RF_CHANGE_BY_IPS);

	/*
	 *	To solve CAM values miss in RF OFF, rewrite CAM values after RF ON. By Bruce, 2007-09-20.
	 */

	priv->bSwRfProcessing = false;
}

/*
 *	Description:
 *		Enter the inactive power save mode. RF will be off
 */
void IPSEnter(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	RT_RF_POWER_STATE rtState;
	if (priv->bInactivePs) {
		rtState = priv->eRFPowerState;

		/*
		 *	Do not enter IPS in the following conditions:
		 *	(1) RF is already OFF or Sleep
		 *	(2) bSwRfProcessing (indicates the IPS is still under going)
		 *	(3) Connected (only disconnected can trigger IPS)
		 *	(4) IBSS (send Beacon)
		 *	(5) AP mode (send Beacon)
		 */
		if (rtState == eRfOn && !priv->bSwRfProcessing
			&& (priv->ieee80211->state != IEEE80211_LINKED)) {
			priv->eInactivePowerState = eRfOff;
			InactivePowerSave(dev);
		}
	}
}
void IPSLeave(struct net_device *dev)
{
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);
	RT_RF_POWER_STATE rtState;
	if (priv->bInactivePs) {
		rtState = priv->eRFPowerState;
		if ((rtState == eRfOff || rtState == eRfSleep) && (!priv->bSwRfProcessing) && priv->RfOffReason <= RF_CHANGE_BY_IPS) {
			priv->eInactivePowerState = eRfOn;
			InactivePowerSave(dev);
		}
	}
}

void rtl8185b_adapter_start(struct net_device *dev)
{
	struct r8180_priv *priv = ieee80211_priv(dev);
	struct ieee80211_device *ieee = priv->ieee80211;

	u8 SupportedWirelessMode;
	u8 InitWirelessMode;
	u8 bInvalidWirelessMode = 0;
	u8 tmpu8;
	u8 btCR9346;
	u8 TmpU1b;
	u8 btPSR;

	write_nic_byte(dev, 0x24e, (BIT5|BIT6|BIT0));
	rtl8180_reset(dev);

	priv->dma_poll_mask = 0;
	priv->dma_poll_stop_mask = 0;

	HwConfigureRTL8185(dev);
	write_nic_dword(dev, MAC0, ((u32 *)dev->dev_addr)[0]);
	write_nic_word(dev, MAC4, ((u32 *)dev->dev_addr)[1] & 0xffff);
	write_nic_byte(dev, MSR, read_nic_byte(dev, MSR) & 0xf3); /* default network type to 'No Link' */
	write_nic_word(dev, BcnItv, 100);
	write_nic_word(dev, AtimWnd, 2);
	PlatformIOWrite2Byte(dev, FEMR, 0xFFFF);
	write_nic_byte(dev, WPA_CONFIG, 0);
	MacConfig_85BASIC(dev);
	/* Override the RFSW_CTRL (MAC offset 0x272-0x273), 2006.06.07, by rcnjko. */
	/* BT_DEMO_BOARD type */
	PlatformIOWrite2Byte(dev, RFSW_CTRL, 0x569a);

	/*
	 *---------------------------------------------------------------------------
	 *	Set up PHY related.
	 *---------------------------------------------------------------------------
	 */
	/* Enable Config3.PARAM_En to revise AnaaParm. */
	write_nic_byte(dev, CR9346, 0xc0); /* enable config register write */
	tmpu8 = read_nic_byte(dev, CONFIG3);
	write_nic_byte(dev, CONFIG3, (tmpu8 | CONFIG3_PARM_En));
	/* Turn on Analog power. */
	/* Asked for by William, otherwise, MAC 3-wire can't work, 2006.06.27, by rcnjko. */
	write_nic_dword(dev, ANAPARAM2, ANAPARM2_ASIC_ON);
	write_nic_dword(dev, ANAPARAM, ANAPARM_ASIC_ON);
	write_nic_word(dev, ANAPARAM3, 0x0010);

	write_nic_byte(dev, CONFIG3, tmpu8);
	write_nic_byte(dev, CR9346, 0x00);
	/* enable EEM0 and EEM1 in 9346CR */
	btCR9346 = read_nic_byte(dev, CR9346);
	write_nic_byte(dev, CR9346, (btCR9346 | 0xC0));

	/* B cut use LED1 to control HW RF on/off */
	TmpU1b = read_nic_byte(dev, CONFIG5);
	TmpU1b = TmpU1b & ~BIT3;
	write_nic_byte(dev, CONFIG5, TmpU1b);

	/* disable EEM0 and EEM1 in 9346CR */
	btCR9346 &= ~(0xC0);
	write_nic_byte(dev, CR9346, btCR9346);

	/* Enable Led (suggested by Jong) */
	/* B-cut RF Radio on/off  5e[3]=0 */
	btPSR = read_nic_byte(dev, PSR);
	write_nic_byte(dev, PSR, (btPSR | BIT3));
	/* setup initial timing for RFE. */
	write_nic_word(dev, RFPinsOutput, 0x0480);
	SetOutputEnableOfRfPins(dev);
	write_nic_word(dev, RFPinsSelect, 0x2488);

	/* PHY config. */
	PhyConfig8185(dev);

	/*
	 *	We assume RegWirelessMode has already been initialized before,
	 *	however, we has to validate the wireless mode here and provide a
	 *	reasonable initialized value if necessary. 2005.01.13, by rcnjko.
	 */
	SupportedWirelessMode = GetSupportedWirelessMode8185(dev);
	if ((ieee->mode != WIRELESS_MODE_B) &&
		(ieee->mode != WIRELESS_MODE_G) &&
		(ieee->mode != WIRELESS_MODE_A) &&
		(ieee->mode != WIRELESS_MODE_AUTO)) {
		/* It should be one of B, G, A, or AUTO. */
		bInvalidWirelessMode = 1;
	} else {
	/* One of B, G, A, or AUTO. */
		/* Check if the wireless mode is supported by RF. */
		if	((ieee->mode != WIRELESS_MODE_AUTO) &&
			(ieee->mode & SupportedWirelessMode) == 0) {
			bInvalidWirelessMode = 1;
		}
	}

	if (bInvalidWirelessMode || ieee->mode == WIRELESS_MODE_AUTO) {
		/* Auto or other invalid value. */
		/* Assigne a wireless mode to initialize. */
		if ((SupportedWirelessMode & WIRELESS_MODE_A)) {
			InitWirelessMode = WIRELESS_MODE_A;
		} else if ((SupportedWirelessMode & WIRELESS_MODE_G)) {
			InitWirelessMode = WIRELESS_MODE_G;
		} else if ((SupportedWirelessMode & WIRELESS_MODE_B)) {
			InitWirelessMode = WIRELESS_MODE_B;
		} else {
			DMESGW("InitializeAdapter8185(): No valid wireless mode supported, SupportedWirelessMode(%x)!!!\n",
				 SupportedWirelessMode);
			InitWirelessMode = WIRELESS_MODE_B;
		}

		/* Initialize RegWirelessMode if it is not a valid one.	*/
		if (bInvalidWirelessMode)
			ieee->mode = (WIRELESS_MODE)InitWirelessMode;

	} else {
	/* One of B, G, A. */
		InitWirelessMode = ieee->mode;
	}
	priv->eRFPowerState = eRfOff;
	priv->RfOffReason = 0;
	{
		MgntActSet_RF_State(dev, eRfOn, 0);
	}
		/*
		 *	If inactive power mode is enabled, disable rf while in disconnected state.
		 */
	if (priv->bInactivePs)
		MgntActSet_RF_State(dev , eRfOff, RF_CHANGE_BY_IPS);

	ActSetWirelessMode8185(dev, (u8)(InitWirelessMode));

	/* ----------------------------------------------------------------------------- */

	rtl8185b_irq_enable(dev);

	netif_start_queue(dev);
}

void rtl8185b_rx_enable(struct net_device *dev)
{
	u8 cmd;
	/* for now we accept data, management & ctl frame*/
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);


	if (dev->flags & IFF_PROMISC)
		DMESG("NIC in promisc mode");

	if (priv->ieee80211->iw_mode == IW_MODE_MONITOR || \
	   dev->flags & IFF_PROMISC) {
		priv->ReceiveConfig = priv->ReceiveConfig & (~RCR_APM);
		priv->ReceiveConfig = priv->ReceiveConfig | RCR_AAP;
	}

	if (priv->ieee80211->iw_mode == IW_MODE_MONITOR)
		priv->ReceiveConfig = priv->ReceiveConfig | RCR_ACF | RCR_APWRMGT | RCR_AICV;


	if (priv->crcmon == 1 && priv->ieee80211->iw_mode == IW_MODE_MONITOR)
		priv->ReceiveConfig = priv->ReceiveConfig | RCR_ACRC32;

	write_nic_dword(dev, RCR, priv->ReceiveConfig);

	fix_rx_fifo(dev);

	cmd = read_nic_byte(dev, CMD);
	write_nic_byte(dev, CMD, cmd | (1<<CMD_RX_ENABLE_SHIFT));

}

void rtl8185b_tx_enable(struct net_device *dev)
{
	u8 cmd;
	u8 byte;
	struct r8180_priv *priv = (struct r8180_priv *)ieee80211_priv(dev);

	write_nic_dword(dev, TCR, priv->TransmitConfig);
	byte = read_nic_byte(dev, MSR);
	byte |= MSR_LINK_ENEDCA;
	write_nic_byte(dev, MSR, byte);

	fix_tx_fifo(dev);

	cmd = read_nic_byte(dev, CMD);
	write_nic_byte(dev, CMD, cmd | (1<<CMD_TX_ENABLE_SHIFT));
}