diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 1df9d4c..2aafda9 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -59,7 +59,30 @@
       p) Freescale Synchronous Serial Interface
 	  q) USB EHCI controllers
 
-  VII - Specifying interrupt information for devices
+  VII - Marvell Discovery mv64[345]6x System Controller chips
+    1) The /system-controller node
+    2) Child nodes of /system-controller
+      a) Marvell Discovery MDIO bus
+      b) Marvell Discovery ethernet controller
+      c) Marvell Discovery PHY nodes
+      d) Marvell Discovery SDMA nodes
+      e) Marvell Discovery BRG nodes
+      f) Marvell Discovery CUNIT nodes
+      g) Marvell Discovery MPSCROUTING nodes
+      h) Marvell Discovery MPSCINTR nodes
+      i) Marvell Discovery MPSC nodes
+      j) Marvell Discovery Watch Dog Timer nodes
+      k) Marvell Discovery I2C nodes
+      l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+      m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+      n) Marvell Discovery GPP (General Purpose Pins) nodes
+      o) Marvell Discovery PCI host bridge node
+      p) Marvell Discovery CPU Error nodes
+      q) Marvell Discovery SRAM Controller nodes
+      r) Marvell Discovery PCI Error Handler nodes
+      s) Marvell Discovery Memory Controller nodes
+
+  VIII - Specifying interrupt information for devices
     1) interrupts property
     2) interrupt-parent property
     3) OpenPIC Interrupt Controllers
@@ -2801,9 +2824,528 @@
 	   };
 
 
-   More devices will be defined as this spec matures.
+VII - Marvell Discovery mv64[345]6x System Controller chips
+===========================================================
 
-VII - Specifying interrupt information for devices
+The Marvell mv64[345]60 series of system controller chips contain
+many of the peripherals needed to implement a complete computer
+system.  In this section, we define device tree nodes to describe
+the system controller chip itself and each of the peripherals
+which it contains.  Compatible string values for each node are
+prefixed with the string "marvell,", for Marvell Technology Group Ltd.
+
+1) The /system-controller node
+
+  This node is used to represent the system-controller and must be
+  present when the system uses a system contller chip. The top-level
+  system-controller node contains information that is global to all
+  devices within the system controller chip. The node name begins
+  with "system-controller" followed by the unit address, which is
+  the base address of the memory-mapped register set for the system
+  controller chip.
+
+  Required properties:
+
+    - ranges : Describes the translation of system controller addresses
+      for memory mapped registers.
+    - clock-frequency: Contains the main clock frequency for the system
+      controller chip.
+    - reg : This property defines the address and size of the
+      memory-mapped registers contained within the system controller
+      chip.  The address specified in the "reg" property should match
+      the unit address of the system-controller node.
+    - #address-cells : Address representation for system controller
+      devices.  This field represents the number of cells needed to
+      represent the address of the memory-mapped registers of devices
+      within the system controller chip.
+    - #size-cells : Size representation for for the memory-mapped
+      registers within the system controller chip.
+    - #interrupt-cells : Defines the width of cells used to represent
+      interrupts.
+
+  Optional properties:
+
+    - model : The specific model of the system controller chip.  Such
+      as, "mv64360", "mv64460", or "mv64560".
+    - compatible : A string identifying the compatibility identifiers
+      of the system controller chip.
+
+  The system-controller node contains child nodes for each system
+  controller device that the platform uses.  Nodes should not be created
+  for devices which exist on the system controller chip but are not used
+
+  Example Marvell Discovery mv64360 system-controller node:
+
+    system-controller@f1000000 { /* Marvell Discovery mv64360 */
+	    #address-cells = <1>;
+	    #size-cells = <1>;
+	    model = "mv64360";                      /* Default */
+	    compatible = "marvell,mv64360";
+	    clock-frequency = <133333333>;
+	    reg = <0xf1000000 0x10000>;
+	    virtual-reg = <0xf1000000>;
+	    ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
+		    0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
+		    0xa0000000 0xa0000000 0x4000000 /* User FLASH */
+		    0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
+		    0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
+
+	    [ child node definitions... ]
+    }
+
+2) Child nodes of /system-controller
+
+   a) Marvell Discovery MDIO bus
+
+   The MDIO is a bus to which the PHY devices are connected.  For each
+   device that exists on this bus, a child node should be created.  See
+   the definition of the PHY node below for an example of how to define
+   a PHY.
+
+   Required properties:
+     - #address-cells : Should be <1>
+     - #size-cells : Should be <0>
+     - device_type : Should be "mdio"
+     - compatible : Should be "marvell,mv64360-mdio"
+
+   Example:
+
+     mdio {
+	     #address-cells = <1>;
+	     #size-cells = <0>;
+	     device_type = "mdio";
+	     compatible = "marvell,mv64360-mdio";
+
+	     ethernet-phy@0 {
+		     ......
+	     };
+     };
+
+
+   b) Marvell Discovery ethernet controller
+
+   The Discover ethernet controller is described with two levels
+   of nodes.  The first level describes an ethernet silicon block
+   and the second level describes up to 3 ethernet nodes within
+   that block.  The reason for the multiple levels is that the
+   registers for the node are interleaved within a single set
+   of registers.  The "ethernet-block" level describes the
+   shared register set, and the "ethernet" nodes describe ethernet
+   port-specific properties.
+
+   Ethernet block node
+
+   Required properties:
+     - #address-cells : <1>
+     - #size-cells : <0>
+     - compatible : "marvell,mv64360-eth-block"
+     - reg : Offset and length of the register set for this block
+
+   Example Discovery Ethernet block node:
+     ethernet-block@2000 {
+	     #address-cells = <1>;
+	     #size-cells = <0>;
+	     compatible = "marvell,mv64360-eth-block";
+	     reg = <0x2000 0x2000>;
+	     ethernet@0 {
+		     .......
+	     };
+     };
+
+   Ethernet port node
+
+   Required properties:
+     - device_type : Should be "network".
+     - compatible : Should be "marvell,mv64360-eth".
+     - reg : Should be <0>, <1>, or <2>, according to which registers
+       within the silicon block the device uses.
+     - interrupts : <a> where a is the interrupt number for the port.
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+     - phy : the phandle for the PHY connected to this ethernet
+       controller.
+     - local-mac-address : 6 bytes, MAC address
+
+   Example Discovery Ethernet port node:
+     ethernet@0 {
+	     device_type = "network";
+	     compatible = "marvell,mv64360-eth";
+	     reg = <0>;
+	     interrupts = <32>;
+	     interrupt-parent = <&PIC>;
+	     phy = <&PHY0>;
+	     local-mac-address = [ 00 00 00 00 00 00 ];
+     };
+
+
+
+   c) Marvell Discovery PHY nodes
+
+   Required properties:
+     - device_type : Should be "ethernet-phy"
+     - interrupts : <a> where a is the interrupt number for this phy.
+     - interrupt-parent : the phandle for the interrupt controller that
+       services interrupts for this device.
+     - reg : The ID number for the phy, usually a small integer
+
+   Example Discovery PHY node:
+     ethernet-phy@1 {
+	     device_type = "ethernet-phy";
+	     compatible = "broadcom,bcm5421";
+	     interrupts = <76>;      /* GPP 12 */
+	     interrupt-parent = <&PIC>;
+	     reg = <1>;
+     };
+
+
+   d) Marvell Discovery SDMA nodes
+
+   Represent DMA hardware associated with the MPSC (multiprotocol
+   serial controllers).
+
+   Required properties:
+     - compatible : "marvell,mv64360-sdma"
+     - reg : Offset and length of the register set for this device
+     - interrupts : <a> where a is the interrupt number for the DMA
+       device.
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery SDMA node:
+     sdma@4000 {
+	     compatible = "marvell,mv64360-sdma";
+	     reg = <0x4000 0xc18>;
+	     virtual-reg = <0xf1004000>;
+	     interrupts = <36>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   e) Marvell Discovery BRG nodes
+
+   Represent baud rate generator hardware associated with the MPSC
+   (multiprotocol serial controllers).
+
+   Required properties:
+     - compatible : "marvell,mv64360-brg"
+     - reg : Offset and length of the register set for this device
+     - clock-src : A value from 0 to 15 which selects the clock
+       source for the baud rate generator.  This value corresponds
+       to the CLKS value in the BRGx configuration register.  See
+       the mv64x60 User's Manual.
+     - clock-frequence : The frequency (in Hz) of the baud rate
+       generator's input clock.
+     - current-speed : The current speed setting (presumably by
+       firmware) of the baud rate generator.
+
+   Example Discovery BRG node:
+     brg@b200 {
+	     compatible = "marvell,mv64360-brg";
+	     reg = <0xb200 0x8>;
+	     clock-src = <8>;
+	     clock-frequency = <133333333>;
+	     current-speed = <9600>;
+     };
+
+
+   f) Marvell Discovery CUNIT nodes
+
+   Represent the Serial Communications Unit device hardware.
+
+   Required properties:
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery CUNIT node:
+     cunit@f200 {
+	     reg = <0xf200 0x200>;
+     };
+
+
+   g) Marvell Discovery MPSCROUTING nodes
+
+   Represent the Discovery's MPSC routing hardware
+
+   Required properties:
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery CUNIT node:
+     mpscrouting@b500 {
+	     reg = <0xb400 0xc>;
+     };
+
+
+   h) Marvell Discovery MPSCINTR nodes
+
+   Represent the Discovery's MPSC DMA interrupt hardware registers
+   (SDMA cause and mask registers).
+
+   Required properties:
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery MPSCINTR node:
+     mpsintr@b800 {
+	     reg = <0xb800 0x100>;
+     };
+
+
+   i) Marvell Discovery MPSC nodes
+
+   Represent the Discovery's MPSC (Multiprotocol Serial Controller)
+   serial port.
+
+   Required properties:
+     - device_type : "serial"
+     - compatible : "marvell,mv64360-mpsc"
+     - reg : Offset and length of the register set for this device
+     - sdma : the phandle for the SDMA node used by this port
+     - brg : the phandle for the BRG node used by this port
+     - cunit : the phandle for the CUNIT node used by this port
+     - mpscrouting : the phandle for the MPSCROUTING node used by this port
+     - mpscintr : the phandle for the MPSCINTR node used by this port
+     - cell-index : the hardware index of this cell in the MPSC core
+     - max_idle : value needed for MPSC CHR3 (Maximum Frame Length)
+       register
+     - interrupts : <a> where a is the interrupt number for the MPSC.
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery MPSCINTR node:
+     mpsc@8000 {
+	     device_type = "serial";
+	     compatible = "marvell,mv64360-mpsc";
+	     reg = <0x8000 0x38>;
+	     virtual-reg = <0xf1008000>;
+	     sdma = <&SDMA0>;
+	     brg = <&BRG0>;
+	     cunit = <&CUNIT>;
+	     mpscrouting = <&MPSCROUTING>;
+	     mpscintr = <&MPSCINTR>;
+	     cell-index = <0>;
+	     max_idle = <40>;
+	     interrupts = <40>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   j) Marvell Discovery Watch Dog Timer nodes
+
+   Represent the Discovery's watchdog timer hardware
+
+   Required properties:
+     - compatible : "marvell,mv64360-wdt"
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery Watch Dog Timer node:
+     wdt@b410 {
+	     compatible = "marvell,mv64360-wdt";
+	     reg = <0xb410 0x8>;
+     };
+
+
+   k) Marvell Discovery I2C nodes
+
+   Represent the Discovery's I2C hardware
+
+   Required properties:
+     - device_type : "i2c"
+     - compatible : "marvell,mv64360-i2c"
+     - reg : Offset and length of the register set for this device
+     - interrupts : <a> where a is the interrupt number for the I2C.
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery I2C node:
+	     compatible = "marvell,mv64360-i2c";
+	     reg = <0xc000 0x20>;
+	     virtual-reg = <0xf100c000>;
+	     interrupts = <37>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+
+   Represent the Discovery's PIC hardware
+
+   Required properties:
+     - #interrupt-cells : <1>
+     - #address-cells : <0>
+     - compatible : "marvell,mv64360-pic"
+     - reg : Offset and length of the register set for this device
+     - interrupt-controller
+
+   Example Discovery PIC node:
+     pic {
+	     #interrupt-cells = <1>;
+	     #address-cells = <0>;
+	     compatible = "marvell,mv64360-pic";
+	     reg = <0x0 0x88>;
+	     interrupt-controller;
+     };
+
+
+   m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+
+   Represent the Discovery's MPP hardware
+
+   Required properties:
+     - compatible : "marvell,mv64360-mpp"
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery MPP node:
+     mpp@f000 {
+	     compatible = "marvell,mv64360-mpp";
+	     reg = <0xf000 0x10>;
+     };
+
+
+   n) Marvell Discovery GPP (General Purpose Pins) nodes
+
+   Represent the Discovery's GPP hardware
+
+   Required properties:
+     - compatible : "marvell,mv64360-gpp"
+     - reg : Offset and length of the register set for this device
+
+   Example Discovery GPP node:
+     gpp@f000 {
+	     compatible = "marvell,mv64360-gpp";
+	     reg = <0xf100 0x20>;
+     };
+
+
+   o) Marvell Discovery PCI host bridge node
+
+   Represents the Discovery's PCI host bridge device.  The properties
+   for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE
+   1275-1994.  A typical value for the compatible property is
+   "marvell,mv64360-pci".
+
+   Example Discovery PCI host bridge node
+     pci@80000000 {
+	     #address-cells = <3>;
+	     #size-cells = <2>;
+	     #interrupt-cells = <1>;
+	     device_type = "pci";
+	     compatible = "marvell,mv64360-pci";
+	     reg = <0xcf8 0x8>;
+	     ranges = <0x01000000 0x0        0x0
+			     0x88000000 0x0 0x01000000
+		       0x02000000 0x0 0x80000000
+			     0x80000000 0x0 0x08000000>;
+	     bus-range = <0 255>;
+	     clock-frequency = <66000000>;
+	     interrupt-parent = <&PIC>;
+	     interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+	     interrupt-map = <
+		     /* IDSEL 0x0a */
+		     0x5000 0 0 1 &PIC 80
+		     0x5000 0 0 2 &PIC 81
+		     0x5000 0 0 3 &PIC 91
+		     0x5000 0 0 4 &PIC 93
+
+		     /* IDSEL 0x0b */
+		     0x5800 0 0 1 &PIC 91
+		     0x5800 0 0 2 &PIC 93
+		     0x5800 0 0 3 &PIC 80
+		     0x5800 0 0 4 &PIC 81
+
+		     /* IDSEL 0x0c */
+		     0x6000 0 0 1 &PIC 91
+		     0x6000 0 0 2 &PIC 93
+		     0x6000 0 0 3 &PIC 80
+		     0x6000 0 0 4 &PIC 81
+
+		     /* IDSEL 0x0d */
+		     0x6800 0 0 1 &PIC 93
+		     0x6800 0 0 2 &PIC 80
+		     0x6800 0 0 3 &PIC 81
+		     0x6800 0 0 4 &PIC 91
+	     >;
+     };
+
+
+   p) Marvell Discovery CPU Error nodes
+
+   Represent the Discovery's CPU error handler device.
+
+   Required properties:
+     - compatible : "marvell,mv64360-cpu-error"
+     - reg : Offset and length of the register set for this device
+     - interrupts : the interrupt number for this device
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery CPU Error node:
+     cpu-error@0070 {
+	     compatible = "marvell,mv64360-cpu-error";
+	     reg = <0x70 0x10 0x128 0x28>;
+	     interrupts = <3>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   q) Marvell Discovery SRAM Controller nodes
+
+   Represent the Discovery's SRAM controller device.
+
+   Required properties:
+     - compatible : "marvell,mv64360-sram-ctrl"
+     - reg : Offset and length of the register set for this device
+     - interrupts : the interrupt number for this device
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery SRAM Controller node:
+     sram-ctrl@0380 {
+	     compatible = "marvell,mv64360-sram-ctrl";
+	     reg = <0x380 0x80>;
+	     interrupts = <13>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   r) Marvell Discovery PCI Error Handler nodes
+
+   Represent the Discovery's PCI error handler device.
+
+   Required properties:
+     - compatible : "marvell,mv64360-pci-error"
+     - reg : Offset and length of the register set for this device
+     - interrupts : the interrupt number for this device
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery PCI Error Handler node:
+     pci-error@1d40 {
+	     compatible = "marvell,mv64360-pci-error";
+	     reg = <0x1d40 0x40 0xc28 0x4>;
+	     interrupts = <12>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+   s) Marvell Discovery Memory Controller nodes
+
+   Represent the Discovery's memory controller device.
+
+   Required properties:
+     - compatible : "marvell,mv64360-mem-ctrl"
+     - reg : Offset and length of the register set for this device
+     - interrupts : the interrupt number for this device
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+
+   Example Discovery Memory Controller node:
+     mem-ctrl@1400 {
+	     compatible = "marvell,mv64360-mem-ctrl";
+	     reg = <0x1400 0x60>;
+	     interrupts = <17>;
+	     interrupt-parent = <&PIC>;
+     };
+
+
+VIII - Specifying interrupt information for devices
 ===================================================
 
 The device tree represents the busses and devices of a hardware