diff --git a/arch/ppc/8xx_io/enet.c b/arch/ppc/8xx_io/enet.c
index 4ea7158..ece6a9f 100644
--- a/arch/ppc/8xx_io/enet.c
+++ b/arch/ppc/8xx_io/enet.c
@@ -714,17 +714,25 @@
 	immap->im_ioport.iop_pcdat &= ~PC_ENET_LBK;	/* Disable Loopback */
 #endif	/* PC_ENET_LBK */
 
+#ifdef PE_ENET_TCLK
+	/* Configure port E for TCLK and RCLK.
+	*/
+	cp->cp_pepar |=  (PE_ENET_TCLK | PE_ENET_RCLK);
+	cp->cp_pedir &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
+	cp->cp_peso  &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
+#else
+	/* Configure port A for TCLK and RCLK.
+	*/
+	immap->im_ioport.iop_papar |=  (PA_ENET_TCLK | PA_ENET_RCLK);
+	immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
+#endif
+
 	/* Configure port C pins to enable CLSN and RENA.
 	*/
 	immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
 	immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
 	immap->im_ioport.iop_pcso  |=  (PC_ENET_CLSN | PC_ENET_RENA);
 
-	/* Configure port A for TCLK and RCLK.
-	*/
-	immap->im_ioport.iop_papar |=  (PA_ENET_TCLK | PA_ENET_RCLK);
-	immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
-
 	/* Configure Serial Interface clock routing.
 	 * First, clear all SCC bits to zero, then set the ones we want.
 	 */
@@ -896,14 +904,18 @@
 	/* It is now OK to enable the Ethernet transmitter.
 	 * Unfortunately, there are board implementation differences here.
 	 */
-#if   (!defined (PB_ENET_TENA) &&  defined (PC_ENET_TENA))
+#if   (!defined (PB_ENET_TENA) &&  defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
 	immap->im_ioport.iop_pcpar |=  PC_ENET_TENA;
 	immap->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
-#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA))
+#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
 	cp->cp_pbpar |= PB_ENET_TENA;
 	cp->cp_pbdir |= PB_ENET_TENA;
+#elif ( !defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && defined (PE_ENET_TENA))
+	cp->cp_pepar |=  PE_ENET_TENA;
+	cp->cp_pedir &= ~PE_ENET_TENA;
+	cp->cp_peso  |=  PE_ENET_TENA;
 #else
-#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA
+#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA, PE_ENET_TENA
 #endif
 
 #if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC)
@@ -936,6 +948,29 @@
 	*((volatile uint *)BCSR1) &= ~BCSR1_ETHEN;
 #endif
 
+#ifdef CONFIG_MPC885ADS
+
+	/* Deassert PHY reset and enable the PHY.
+	 */
+	{
+		volatile uint __iomem *bcsr = ioremap(BCSR_ADDR, BCSR_SIZE);
+		uint tmp;
+
+		tmp = in_be32(bcsr + 1 /* BCSR1 */);
+		tmp |= BCSR1_ETHEN;
+		out_be32(bcsr + 1, tmp);
+		tmp = in_be32(bcsr + 4 /* BCSR4 */);
+		tmp |= BCSR4_ETH10_RST;
+		out_be32(bcsr + 4, tmp);
+		iounmap(bcsr);
+	}
+
+	/* On MPC885ADS SCC ethernet PHY defaults to the full duplex mode
+	 * upon reset. SCC is set to half duplex by default. So this
+	 * inconsistency should be better fixed by the software.
+	 */
+#endif
+
 	dev->base_addr = (unsigned long)ep;
 #if 0
 	dev->name = "CPM_ENET";
@@ -969,3 +1004,4 @@
 }
 
 module_init(scc_enet_init);
+
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index a7835cd..23b0d2f 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -284,6 +284,9 @@
 
 menu "Platform options"
 
+config FADS
+	bool
+
 choice
 	prompt "8xx Machine Type"
 	depends on 8xx
@@ -399,8 +402,25 @@
 	  26MB DRAM, 4MB flash, Ethernet, a 16K-gate FPGA, USB, an LCD/video
 	  controller, and two RS232 ports.
 
-config FADS
+config MPC8XXFADS
 	bool "FADS"
+	select FADS
+
+config MPC86XADS
+	bool "MPC86XADS"
+	help
+	  MPC86x Application Development System by Freescale Semiconductor.
+	  The MPC86xADS is meant to serve as a platform for s/w and h/w
+	  development around the MPC86X processor families.
+	select FADS
+
+config MPC885ADS
+	bool "MPC885ADS"
+	help
+	  Freescale Semiconductor MPC885 Application Development System (ADS).
+	  Also known as DUET.
+	  The MPC885ADS is meant to serve as a platform for s/w and h/w
+	  development around the MPC885 processor family.
 
 config TQM823L
 	bool "TQM823L"
diff --git a/arch/ppc/configs/mpc86x_ads_defconfig b/arch/ppc/configs/mpc86x_ads_defconfig
new file mode 100644
index 0000000..f63c6f5
--- /dev/null
+++ b/arch/ppc/configs/mpc86x_ads_defconfig
@@ -0,0 +1,633 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.12-rc4
+# Tue Jun 14 13:36:35 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_HAVE_DEC_LOCK=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+# CONFIG_CLEAN_COMPILE is not set
+CONFIG_BROKEN=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_BASE_FULL is not set
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+# CONFIG_SHMEM is not set
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_TINY_SHMEM=y
+CONFIG_BASE_SMALL=1
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+# CONFIG_MODULE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+CONFIG_8xx=y
+# CONFIG_E500 is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_EMBEDDEDBOOT=y
+# CONFIG_PM is not set
+CONFIG_NOT_COHERENT_CACHE=y
+
+#
+# Platform options
+#
+CONFIG_FADS=y
+# CONFIG_RPXLITE is not set
+# CONFIG_RPXCLASSIC is not set
+# CONFIG_BSEIP is not set
+# CONFIG_MPC8XXFADS is not set
+CONFIG_MPC86XADS=y
+# CONFIG_TQM823L is not set
+# CONFIG_TQM850L is not set
+# CONFIG_TQM855L is not set
+# CONFIG_TQM860L is not set
+# CONFIG_FPS850L is not set
+# CONFIG_SPD823TS is not set
+# CONFIG_IVMS8 is not set
+# CONFIG_IVML24 is not set
+# CONFIG_SM850 is not set
+# CONFIG_HERMES_PRO is not set
+# CONFIG_IP860 is not set
+# CONFIG_LWMON is not set
+# CONFIG_PCU_E is not set
+# CONFIG_CCM is not set
+# CONFIG_LANTEC is not set
+# CONFIG_MBX is not set
+# CONFIG_WINCEPT is not set
+# CONFIG_SMP is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_QSPAN is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+# CONFIG_STANDALONE is not set
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_LBD is not set
+# CONFIG_CDROM_PKTCDVD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+
+#
+# Macintosh device drivers
+#
+
+#
+# Networking support
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_IP_TCPDIAG=y
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+CONFIG_IPV6=m
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_NETFILTER is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+# CONFIG_MII is not set
+# CONFIG_OAKNET is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+
+#
+# Ethernet (10000 Mbit)
+#
+
+#
+# Token Ring devices
+#
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+CONFIG_SOUND_GAMEPORT=y
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+# CONFIG_SERIAL_CPM_SMC2 is not set
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+
+#
+# XFS support
+#
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+# CONFIG_DEVFS_FS is not set
+# CONFIG_DEVPTS_FS_XATTR is not set
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLBFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V4=y
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# MPC8xx CPM Options
+#
+CONFIG_SCC_ENET=y
+CONFIG_SCC1_ENET=y
+# CONFIG_SCC2_ENET is not set
+# CONFIG_SCC3_ENET is not set
+# CONFIG_FEC_ENET is not set
+# CONFIG_ENET_BIG_BUFFERS is not set
+
+#
+# Generic MPC8xx Options
+#
+# CONFIG_8xx_COPYBACK is not set
+# CONFIG_8xx_CPU6 is not set
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC32 is not set
+# CONFIG_LIBCRC32C is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/configs/mpc885ads_defconfig b/arch/ppc/configs/mpc885ads_defconfig
new file mode 100644
index 0000000..016f94d
--- /dev/null
+++ b/arch/ppc/configs/mpc885ads_defconfig
@@ -0,0 +1,622 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.12-rc6
+# Thu Jun  9 21:17:29 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_HAVE_DEC_LOCK=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+# CONFIG_CLEAN_COMPILE is not set
+CONFIG_BROKEN=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+CONFIG_HOTPLUG=y
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_EMBEDDED=y
+# CONFIG_KALLSYMS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+CONFIG_8xx=y
+# CONFIG_E500 is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_EMBEDDEDBOOT=y
+# CONFIG_PM is not set
+CONFIG_NOT_COHERENT_CACHE=y
+
+#
+# Platform options
+#
+# CONFIG_RPXLITE is not set
+# CONFIG_RPXCLASSIC is not set
+# CONFIG_BSEIP is not set
+# CONFIG_FADS is not set
+CONFIG_MPC885ADS=y
+# CONFIG_TQM823L is not set
+# CONFIG_TQM850L is not set
+# CONFIG_TQM855L is not set
+# CONFIG_TQM860L is not set
+# CONFIG_FPS850L is not set
+# CONFIG_SPD823TS is not set
+# CONFIG_IVMS8 is not set
+# CONFIG_IVML24 is not set
+# CONFIG_SM850 is not set
+# CONFIG_HERMES_PRO is not set
+# CONFIG_IP860 is not set
+# CONFIG_LWMON is not set
+# CONFIG_PCU_E is not set
+# CONFIG_CCM is not set
+# CONFIG_LANTEC is not set
+# CONFIG_MBX is not set
+# CONFIG_WINCEPT is not set
+# CONFIG_SMP is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_QSPAN is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_LBD is not set
+# CONFIG_CDROM_PKTCDVD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+
+#
+# Macintosh device drivers
+#
+
+#
+# Networking support
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_IP_TCPDIAG=y
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_OAKNET is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+
+#
+# Ethernet (10000 Mbit)
+#
+
+#
+# Token Ring devices
+#
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+CONFIG_PPP=y
+# CONFIG_PPP_MULTILINK is not set
+# CONFIG_PPP_FILTER is not set
+CONFIG_PPP_ASYNC=y
+CONFIG_PPP_SYNC_TTY=y
+CONFIG_PPP_DEFLATE=y
+# CONFIG_PPP_BSDCOMP is not set
+# CONFIG_PPPOE is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+# CONFIG_EXT2_FS_POSIX_ACL is not set
+# CONFIG_EXT2_FS_SECURITY is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+
+#
+# XFS support
+#
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_SYSFS=y
+# CONFIG_DEVFS_FS is not set
+# CONFIG_DEVPTS_FS_XATTR is not set
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLBFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# MPC8xx CPM Options
+#
+CONFIG_SCC_ENET=y
+# CONFIG_SCC1_ENET is not set
+# CONFIG_SCC2_ENET is not set
+CONFIG_SCC3_ENET=y
+# CONFIG_FEC_ENET is not set
+# CONFIG_ENET_BIG_BUFFERS is not set
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+CONFIG_8xx_CPU6=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+
+#
+# Library routines
+#
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC32 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/platforms/fads.h b/arch/ppc/platforms/fads.h
index 632b817..b60c564 100644
--- a/arch/ppc/platforms/fads.h
+++ b/arch/ppc/platforms/fads.h
@@ -3,7 +3,18 @@
  * the Motorola 860T FADS board.  Copied from the MBX stuff.
  *
  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Added MPC86XADS support.
+ * The MPC86xADS manual says the board "is compatible with the MPC8xxFADS
+ * for SW point of view". This is 99% correct.
+ *
+ * Author: MontaVista Software, Inc.
+ *         source@mvista.com
+ * 2005 (c) MontaVista Software, Inc.  This file is licensed under the
+ * terms of the GNU General Public License version 2.  This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
  */
+
 #ifdef __KERNEL__
 #ifndef __ASM_FADS_H__
 #define __ASM_FADS_H__
@@ -12,18 +23,45 @@
 
 #include <asm/ppcboot.h>
 
+#if defined(CONFIG_MPC86XADS)
+
+/* U-Boot maps BCSR to 0xff080000 */
+#define BCSR_ADDR		((uint)0xff080000)
+
+/* MPC86XADS has one more CPLD and an additional BCSR.
+ */
+#define CFG_PHYDEV_ADDR		((uint)0xff0a0000)
+#define BCSR5			((uint)(CFG_PHYDEV_ADDR + 0x300))
+
+#define BCSR5_T1_RST		0x10
+#define BCSR5_ATM155_RST	0x08
+#define BCSR5_ATM25_RST		0x04
+#define BCSR5_MII1_EN		0x02
+#define BCSR5_MII1_RST		0x01
+
+/* There is no PHY link change interrupt */
+#define PHY_INTERRUPT	(-1)
+
+#else /* FADS */
+
 /* Memory map is configured by the PROM startup.
  * I tried to follow the FADS manual, although the startup PROM
  * dictates this and we simply have to move some of the physical
  * addresses for Linux.
  */
 #define BCSR_ADDR		((uint)0xff010000)
+
+/* PHY link change interrupt */
+#define PHY_INTERRUPT	SIU_IRQ2
+
+#endif /* CONFIG_MPC86XADS */
+
 #define BCSR_SIZE		((uint)(64 * 1024))
-#define	BCSR0			((uint)0xff010000)
-#define	BCSR1			((uint)0xff010004)
-#define	BCSR2			((uint)0xff010008)
-#define	BCSR3			((uint)0xff01000c)
-#define	BCSR4			((uint)0xff010010)
+#define BCSR0			((uint)(BCSR_ADDR + 0x00))
+#define BCSR1			((uint)(BCSR_ADDR + 0x04))
+#define BCSR2			((uint)(BCSR_ADDR + 0x08))
+#define BCSR3			((uint)(BCSR_ADDR + 0x0c))
+#define BCSR4			((uint)(BCSR_ADDR + 0x10))
 
 #define IMAP_ADDR		((uint)0xff000000)
 #define IMAP_SIZE		((uint)(64 * 1024))
@@ -34,8 +72,17 @@
 /* Bits of interest in the BCSRs.
  */
 #define BCSR1_ETHEN		((uint)0x20000000)
+#define BCSR1_IRDAEN		((uint)0x10000000)
 #define BCSR1_RS232EN_1		((uint)0x01000000)
+#define BCSR1_PCCEN		((uint)0x00800000)
+#define BCSR1_PCCVCC0		((uint)0x00400000)
+#define BCSR1_PCCVPP0		((uint)0x00200000)
+#define BCSR1_PCCVPP1		((uint)0x00100000)
+#define BCSR1_PCCVPP_MASK	(BCSR1_PCCVPP0 | BCSR1_PCCVPP1)
 #define BCSR1_RS232EN_2		((uint)0x00040000)
+#define BCSR1_PCCVCC1		((uint)0x00010000)
+#define BCSR1_PCCVCC_MASK	(BCSR1_PCCVCC0 | BCSR1_PCCVCC1)
+
 #define BCSR4_ETHLOOP		((uint)0x80000000)	/* EEST Loopback */
 #define BCSR4_EEFDX		((uint)0x40000000)	/* EEST FDX enable */
 #define BCSR4_FETH_EN		((uint)0x08000000)	/* PHY enable */
@@ -44,14 +91,64 @@
 #define BCSR4_FETHFDE		((uint)0x02000000)	/* PHY FDX advertise */
 #define BCSR4_FETHRST		((uint)0x00200000)	/* PHY Reset */
 
+/* IO_BASE definition for pcmcia.
+ */
+#define _IO_BASE	0x80000000
+#define _IO_BASE_SIZE	0x1000
+
+#ifdef CONFIG_IDE
+#define MAX_HWIFS 1
+#endif
+
 /* Interrupt level assignments.
  */
 #define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-#define PHY_INTERRUPT	SIU_IRQ2	/* PHY link change interrupt */
 
 /* We don't use the 8259.
  */
 #define NR_8259_INTS	0
 
+/* CPM Ethernet through SCC1 or SCC2 */
+
+#ifdef CONFIG_SCC1_ENET		/* Probably 860 variant */
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ * TCLK - CLK1, RCLK - CLK2.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)
+#define PA_ENET_TXD	((ushort)0x0002)
+#define PA_ENET_TCLK	((ushort)0x0100)
+#define PA_ENET_RCLK	((ushort)0x0200)
+#define PB_ENET_TENA	((uint)0x00001000)
+#define PC_ENET_CLSN	((ushort)0x0010)
+#define PC_ENET_RENA	((ushort)0x0020)
+
+/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x0000002c)
+#endif /* CONFIG_SCC1_ENET */
+
+#ifdef CONFIG_SCC2_ENET		/* Probably 823/850 variant */
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ * TCLK - CLK1, RCLK - CLK2.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)
+#define PA_ENET_TXD	((ushort)0x0008)
+#define PA_ENET_TCLK	((ushort)0x0400)
+#define PA_ENET_RCLK	((ushort)0x0200)
+#define PB_ENET_TENA	((uint)0x00002000)
+#define PC_ENET_CLSN	((ushort)0x0040)
+#define PC_ENET_RENA	((ushort)0x0080)
+
+/* Control bits in the SICR to route TCLK and RCLK to
+ * SCC2.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002e00)
+#endif /* CONFIG_SCC2_ENET */
+
 #endif /* __ASM_FADS_H__ */
 #endif /* __KERNEL__ */
diff --git a/arch/ppc/platforms/mpc885ads.h b/arch/ppc/platforms/mpc885ads.h
new file mode 100644
index 0000000..eb38663
--- /dev/null
+++ b/arch/ppc/platforms/mpc885ads.h
@@ -0,0 +1,92 @@
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Freescale MPC885ADS board.
+ * Copied from the FADS stuff.
+ *
+ * Author: MontaVista Software, Inc.
+ *         source@mvista.com
+ *
+ * 2005 (c) MontaVista Software, Inc.  This file is licensed under the
+ * terms of the GNU General Public License version 2.  This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_MPC885ADS_H__
+#define __ASM_MPC885ADS_H__
+
+#include <linux/config.h>
+
+#include <asm/ppcboot.h>
+
+/* U-Boot maps BCSR to 0xff080000 */
+#define BCSR_ADDR		((uint)0xff080000)
+#define BCSR_SIZE		((uint)32)
+#define BCSR0			((uint)(BCSR_ADDR + 0x00))
+#define BCSR1			((uint)(BCSR_ADDR + 0x04))
+#define BCSR2			((uint)(BCSR_ADDR + 0x08))
+#define BCSR3			((uint)(BCSR_ADDR + 0x0c))
+#define BCSR4			((uint)(BCSR_ADDR + 0x10))
+
+#define CFG_PHYDEV_ADDR		((uint)0xff0a0000)
+#define BCSR5			((uint)(CFG_PHYDEV_ADDR + 0x300))
+
+#define IMAP_ADDR		((uint)0xff000000)
+#define IMAP_SIZE		((uint)(64 * 1024))
+
+#define PCMCIA_MEM_ADDR		((uint)0xff020000)
+#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
+
+/* Bits of interest in the BCSRs.
+ */
+#define BCSR1_ETHEN		((uint)0x20000000)
+#define BCSR1_IRDAEN		((uint)0x10000000)
+#define BCSR1_RS232EN_1		((uint)0x01000000)
+#define BCSR1_PCCEN		((uint)0x00800000)
+#define BCSR1_PCCVCC0		((uint)0x00400000)
+#define BCSR1_PCCVPP0		((uint)0x00200000)
+#define BCSR1_PCCVPP1		((uint)0x00100000)
+#define BCSR1_PCCVPP_MASK	(BCSR1_PCCVPP0 | BCSR1_PCCVPP1)
+#define BCSR1_RS232EN_2		((uint)0x00040000)
+#define BCSR1_PCCVCC1		((uint)0x00010000)
+#define BCSR1_PCCVCC_MASK	(BCSR1_PCCVCC0 | BCSR1_PCCVCC1)
+
+#define BCSR4_ETH10_RST		((uint)0x80000000)	/* 10Base-T PHY reset*/
+#define BCSR4_USB_LO_SPD	((uint)0x04000000)
+#define BCSR4_USB_VCC		((uint)0x02000000)
+#define BCSR4_USB_FULL_SPD	((uint)0x00040000)
+#define BCSR4_USB_EN		((uint)0x00020000)
+
+#define BCSR5_MII2_EN		0x40
+#define BCSR5_MII2_RST		0x20
+#define BCSR5_T1_RST		0x10
+#define BCSR5_ATM155_RST	0x08
+#define BCSR5_ATM25_RST		0x04
+#define BCSR5_MII1_EN		0x02
+#define BCSR5_MII1_RST		0x01
+
+/* Interrupt level assignments */
+#define PHY_INTERRUPT	SIU_IRQ7	/* PHY link change interrupt */
+#define SIU_INT_FEC1	SIU_LEVEL1	/* FEC1 interrupt */
+#define SIU_INT_FEC2	SIU_LEVEL3	/* FEC2 interrupt */
+#define FEC_INTERRUPT	SIU_INT_FEC1	/* FEC interrupt */
+
+/* We don't use the 8259 */
+#define NR_8259_INTS	0
+
+/* CPM Ethernet through SCC3 */
+#define PA_ENET_RXD	((ushort)0x0040)
+#define PA_ENET_TXD	((ushort)0x0080)
+#define PE_ENET_TCLK	((uint)0x00004000)
+#define PE_ENET_RCLK	((uint)0x00008000)
+#define PE_ENET_TENA	((uint)0x00000010)
+#define PC_ENET_CLSN	((ushort)0x0400)
+#define PC_ENET_RENA	((ushort)0x0800)
+
+/* Control bits in the SICR to route TCLK (CLK5) and RCLK (CLK6) to
+ * SCC3.  Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero */
+#define SICR_ENET_MASK	((uint)0x00ff0000)
+#define SICR_ENET_CLKRT	((uint)0x002c0000)
+
+#endif /* __ASM_MPC885ADS_H__ */
+#endif /* __KERNEL__ */
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
index de26cf7..7911912 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
@@ -94,12 +94,42 @@
 		((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits;
 	}
 
+#ifdef CONFIG_MPC885ADS
+	/* Enable SMC1 transceivers */
+	{
+		volatile uint __iomem *bcsr1 = ioremap(BCSR1, 4);
+		uint tmp;
+
+		tmp = in_be32(bcsr1);
+		tmp &= ~BCSR1_RS232EN_1;
+		out_be32(bcsr1, tmp);
+		iounmap(bcsr1);
+	}
+#endif
+
 	pinfo->brg = 1;
 }
 
 void smc2_lineif(struct uart_cpm_port *pinfo)
 {
-	/* XXX SMC2: insert port configuration here */
+#ifdef CONFIG_MPC885ADS
+	volatile cpm8xx_t *cp = cpmp;
+	volatile uint __iomem *bcsr1;
+	uint tmp;
+
+	cp->cp_pepar |= 0x00000c00;
+	cp->cp_pedir &= ~0x00000c00;
+	cp->cp_peso &= ~0x00000400;
+	cp->cp_peso |= 0x00000800;
+
+	/* Enable SMC2 transceivers */
+	bcsr1 = ioremap(BCSR1, 4);
+	tmp = in_be32(bcsr1);
+	tmp &= ~BCSR1_RS232EN_2;
+	out_be32(bcsr1, tmp);
+	iounmap(bcsr1);
+#endif
+
 	pinfo->brg = 2;
 }
 
diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h
index 714d69c..7c31f2d 100644
--- a/include/asm-ppc/mpc8xx.h
+++ b/include/asm-ppc/mpc8xx.h
@@ -68,6 +68,10 @@
 #include <platforms/lantec.h>
 #endif
 
+#if defined(CONFIG_MPC885ADS)
+#include <platforms/mpc885ads.h>
+#endif
+
 /* Currently, all 8xx boards that support a processor to PCI/ISA bridge
  * use the same memory map.
  */