ipg: remove some internal comments
This removes some now useless comments that were added when the driver was
developed out-of-tree.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Cc: Jesse Huang <jesse@icplus.com.tw>
diff --git a/drivers/net/ipg.c b/drivers/net/ipg.c
index 9e228e7..6b64bc5 100644
--- a/drivers/net/ipg.c
+++ b/drivers/net/ipg.c
@@ -373,7 +373,6 @@
}
}
-/* Set LED_Mode JES20040127EEPROM */
static void ipg_set_led_mode(struct net_device *dev)
{
struct ipg_nic_private *sp = netdev_priv(dev);
@@ -395,7 +394,6 @@
ipg_w32(mode, ASIC_CTRL);
}
-/* Set PHYSet JES20040127EEPROM */
static void ipg_set_phy_set(struct net_device *dev)
{
struct ipg_nic_private *sp = netdev_priv(dev);
@@ -414,7 +412,7 @@
* register as specified by the 'resetflags' input
* parameter.
*/
- void __iomem *ioaddr = ipg_ioaddr(dev); //JES20040127EEPROM:
+ void __iomem *ioaddr = ipg_ioaddr(dev);
unsigned int timeout_count = 0;
IPG_DEBUG_MSG("_reset\n");
@@ -429,10 +427,10 @@
if (++timeout_count > IPG_AC_RESET_TIMEOUT)
return -ETIME;
}
- /* Set LED Mode in Asic Control JES20040127EEPROM */
+ /* Set LED Mode in Asic Control */
ipg_set_led_mode(dev);
- /* Set PHYSet Register Value JES20040127EEPROM */
+ /* Set PHYSet Register Value */
ipg_set_phy_set(dev);
return 0;
}
@@ -2006,7 +2004,6 @@
}
}
-/* JES20040127EEPROM */
static int read_eeprom(struct net_device *dev, int eep_addr)
{
void __iomem *ioaddr = ipg_ioaddr(dev);
@@ -2073,7 +2070,7 @@
unsigned int i;
int rc;
- /* Read/Write and Reset EEPROM Value Jesse20040128EEPROM_VALUE */
+ /* Read/Write and Reset EEPROM Value */
/* Read LED Mode Configuration from EEPROM */
sp->LED_Mode = read_eeprom(dev, 6);
diff --git a/drivers/net/ipg.h b/drivers/net/ipg.h
index 7e3ccd1..a328221 100644
--- a/drivers/net/ipg.h
+++ b/drivers/net/ipg.h
@@ -79,7 +79,7 @@
TX_STATUS = 0x60,
MAC_CTRL = 0x6c,
VLAN_TAG = 0x70, // Unused
- PHY_SET = 0x75, // JES20040127EEPROM
+ PHY_SET = 0x75,
PHY_CTRL = 0x76,
STATION_ADDRESS_0 = 0x78,
STATION_ADDRESS_1 = 0x7a,
@@ -312,7 +312,7 @@
#define IPG_RM_RECEIVEMULTICASTHASH 0x10
#define IPG_RM_RECEIVEIPMULTICAST 0x20
-/* PhySet JES20040127EEPROM*/
+/* PhySet */
#define IPG_PS_MEM_LENB9B 0x01
#define IPG_PS_MEM_LEN9 0x02
#define IPG_PS_NON_COMPDET 0x04
@@ -369,8 +369,8 @@
#define IPG_AC_RST_OUT 0x01000000
#define IPG_AC_INT_REQUEST 0x02000000
#define IPG_AC_RESET_BUSY 0x04000000
-#define IPG_AC_LED_SPEED 0x08000000 //JES20040127EEPROM
-#define IPG_AC_LED_MODE_BIT_1 0x20000000 //JES20040127EEPROM
+#define IPG_AC_LED_SPEED 0x08000000
+#define IPG_AC_LED_MODE_BIT_1 0x20000000
/* EepromCtrl */
#define IPG_EC_RSVD_MASK 0x83FF
@@ -785,7 +785,6 @@
unsigned int tx_dirty;
unsigned int rx_current;
unsigned int rx_dirty;
-// Add by Grace 2005/05/19
#ifdef JUMBO_FRAME
struct SJumbo Jumbo;
#endif
@@ -796,7 +795,6 @@
spinlock_t lock;
int tenmbpsmode;
- /*Jesse20040128EEPROM_VALUE */
u16 LED_Mode;
u16 station_addr[3]; /* Station Address in EEPROM Reg 0x10..0x12 */
