Merge branch 'for-2.6.25' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.25
diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX
index 94a3c57..3be84aa 100644
--- a/Documentation/powerpc/00-INDEX
+++ b/Documentation/powerpc/00-INDEX
@@ -28,3 +28,6 @@
- info on sound support under Linux/PPC
zImage_layout.txt
- info on the kernel images for Linux/PPC
+qe_firmware.txt
+ - describes the layout of firmware binaries for the Freescale QUICC
+ Engine and the code that parses and uploads the microcode therein.
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 6d1d085..da98154 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -52,7 +52,11 @@
i) Freescale QUICC Engine module (QE)
j) CFI or JEDEC memory-mapped NOR flash
k) Global Utilities Block
- l) Xilinx IP cores
+ l) Freescale Communications Processor Module
+ m) Chipselect/Local Bus
+ n) 4xx/Axon EMAC ethernet nodes
+ o) Xilinx IP cores
+ p) Freescale Synchronous Serial Interface
VII - Specifying interrupt information for devices
1) interrupts property
@@ -1257,6 +1261,10 @@
services interrupts for this device.
- phy-handle : The phandle for the PHY connected to this ethernet
controller.
+ - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+ but unique to the all specified fixed-links, b is duplex - 0 half,
+ 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+ pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
Recommended properties:
@@ -1411,7 +1419,6 @@
Example multi port host USB controller device node :
usb@22000 {
- device_type = "usb";
compatible = "fsl-usb2-mph";
reg = <22000 1000>;
#address-cells = <1>;
@@ -1425,7 +1432,6 @@
Example dual role USB controller device node :
usb@23000 {
- device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
@@ -1589,7 +1595,6 @@
iii) USB (Universal Serial Bus Controller)
Required properties:
- - device_type : should be "usb".
- compatible : could be "qe_udc" or "fhci-hcd".
- mode : the could be "host" or "slave".
- reg : Offset and length of the register set for the device
@@ -1603,7 +1608,6 @@
Example(slave):
usb@6c0 {
- device_type = "usb";
compatible = "qe_udc";
reg = <6c0 40>;
interrupts = <8b 0>;
@@ -1616,7 +1620,7 @@
Required properties:
- device_type : should be "network", "hldc", "uart", "transparent"
- "bisync" or "atm".
+ "bisync", "atm", or "serial".
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
- model : should be "UCC".
- device-id : the ucc number(1-8), corresponding to UCCx in UM.
@@ -1629,6 +1633,13 @@
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- pio-handle : The phandle for the Parallel I/O port configuration.
+ - port-number : for UART drivers, the port number to use, between 0 and 3.
+ This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+ The port number is added to the minor number of the device. Unlike the
+ CPM UART driver, the port-number is required for the QE UART driver.
+ - soft-uart : for UART drivers, if specified this means the QE UART device
+ driver should use "Soft-UART" mode, which is needed on some SOCs that have
+ broken UART hardware. Soft-UART is provided via a microcode upload.
- rx-clock-name: the UCC receive clock source
"none": clock source is disabled
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
@@ -1788,6 +1799,32 @@
};
};
+ viii) Uploaded QE firmware
+
+ If a new firwmare has been uploaded to the QE (usually by the
+ boot loader), then a 'firmware' child node should be added to the QE
+ node. This node provides information on the uploaded firmware that
+ device drivers may need.
+
+ Required properties:
+ - id: The string name of the firmware. This is taken from the 'id'
+ member of the qe_firmware structure of the uploaded firmware.
+ Device drivers can search this string to determine if the
+ firmware they want is already present.
+ - extended-modes: The Extended Modes bitfield, taken from the
+ firmware binary. It is a 64-bit number represented
+ as an array of two 32-bit numbers.
+ - virtual-traps: The virtual traps, taken from the firmware binary.
+ It is an array of 8 32-bit numbers.
+
+ Example:
+
+ firmware {
+ id = "Soft-UART";
+ extended-modes = <0 0>;
+ virtual-traps = <0 0 0 0 0 0 0 0>;
+ }
+
j) CFI or JEDEC memory-mapped NOR flash
Flash chips (Memory Technology Devices) are often used for solid state
@@ -2269,7 +2306,7 @@
available.
For Axon: 0x0000012a
- l) Xilinx IP cores
+ o) Xilinx IP cores
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
@@ -2539,6 +2576,46 @@
Requred properties:
- current-speed : Baud rate of uartlite
+ p) Freescale Synchronous Serial Interface
+
+ The SSI is a serial device that communicates with audio codecs. It can
+ be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+ Required properties:
+ - compatible : compatible list, containing "fsl,ssi"
+ - cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
+ - reg : offset and length of the register set for the device
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and
+ level information for the interrupt. This should be
+ encoded based on the information in section 2)
+ depending on the type of interrupt controller you
+ have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - fsl,mode : the operating mode for the SSI interface
+ "i2s-slave" - I2S mode, SSI is clock slave
+ "i2s-master" - I2S mode, SSI is clock master
+ "lj-slave" - left-justified mode, SSI is clock slave
+ "lj-master" - l.j. mode, SSI is clock master
+ "rj-slave" - right-justified mode, SSI is clock slave
+ "rj-master" - r.j., SSI is clock master
+ "ac97-slave" - AC97 mode, SSI is clock slave
+ "ac97-master" - AC97 mode, SSI is clock master
+
+ Optional properties:
+ - codec-handle : phandle to a 'codec' node that defines an audio
+ codec connected to this SSI. This node is typically
+ a child of an I2C or other control node.
+
+ Child 'codec' node required properties:
+ - compatible : compatible list, contains the name of the codec
+
+ Child 'codec' node optional properties:
+ - clock-frequency : The frequency of the input clock, which typically
+ comes from an on-board dedicated oscillator.
+
+
More devices will be defined as this spec matures.
VII - Specifying interrupt information for devices
diff --git a/Documentation/powerpc/qe_firmware.txt b/Documentation/powerpc/qe_firmware.txt
new file mode 100644
index 0000000..8962664
--- /dev/null
+++ b/Documentation/powerpc/qe_firmware.txt
@@ -0,0 +1,295 @@
+ Freescale QUICC Engine Firmware Uploading
+ -----------------------------------------
+
+(c) 2007 Timur Tabi <timur at freescale.com>,
+ Freescale Semiconductor
+
+Table of Contents
+=================
+
+ I - Software License for Firmware
+
+ II - Microcode Availability
+
+ III - Description and Terminology
+
+ IV - Microcode Programming Details
+
+ V - Firmware Structure Layout
+
+ VI - Sample Code for Creating Firmware Files
+
+Revision Information
+====================
+
+November 30, 2007: Rev 1.0 - Initial version
+
+I - Software License for Firmware
+=================================
+
+Each firmware file comes with its own software license. For information on
+the particular license, please see the license text that is distributed with
+the firmware.
+
+II - Microcode Availability
+===========================
+
+Firmware files are distributed through various channels. Some are available on
+http://opensource.freescale.com. For other firmware files, please contact
+your Freescale representative or your operating system vendor.
+
+III - Description and Terminology
+================================
+
+In this document, the term 'microcode' refers to the sequence of 32-bit
+integers that compose the actual QE microcode.
+
+The term 'firmware' refers to a binary blob that contains the microcode as
+well as other data that
+
+ 1) describes the microcode's purpose
+ 2) describes how and where to upload the microcode
+ 3) specifies the values of various registers
+ 4) includes additional data for use by specific device drivers
+
+Firmware files are binary files that contain only a firmware.
+
+IV - Microcode Programming Details
+===================================
+
+The QE architecture allows for only one microcode present in I-RAM for each
+RISC processor. To replace any current microcode, a full QE reset (which
+disables the microcode) must be performed first.
+
+QE microcode is uploaded using the following procedure:
+
+1) The microcode is placed into I-RAM at a specific location, using the
+ IRAM.IADD and IRAM.IDATA registers.
+
+2) The CERCR.CIR bit is set to 0 or 1, depending on whether the firmware
+ needs split I-RAM. Split I-RAM is only meaningful for SOCs that have
+ QEs with multiple RISC processors, such as the 8360. Splitting the I-RAM
+ allows each processor to run a different microcode, effectively creating an
+ asymmetric multiprocessing (AMP) system.
+
+3) The TIBCR trap registers are loaded with the addresses of the trap handlers
+ in the microcode.
+
+4) The RSP.ECCR register is programmed with the value provided.
+
+5) If necessary, device drivers that need the virtual traps and extended mode
+ data will use them.
+
+Virtual Microcode Traps
+
+These virtual traps are conditional branches in the microcode. These are
+"soft" provisional introduced in the ROMcode in order to enable higher
+flexibility and save h/w traps If new features are activated or an issue is
+being fixed in the RAM package utilizing they should be activated. This data
+structure signals the microcode which of these virtual traps is active.
+
+This structure contains 6 words that the application should copy to some
+specific been defined. This table describes the structure.
+
+ ---------------------------------------------------------------
+ | Offset in | | Destination Offset | Size of |
+ | array | Protocol | within PRAM | Operand |
+ --------------------------------------------------------------|
+ | 0 | Ethernet | 0xF8 | 4 bytes |
+ | | interworking | | |
+ ---------------------------------------------------------------
+ | 4 | ATM | 0xF8 | 4 bytes |
+ | | interworking | | |
+ ---------------------------------------------------------------
+ | 8 | PPP | 0xF8 | 4 bytes |
+ | | interworking | | |
+ ---------------------------------------------------------------
+ | 12 | Ethernet RX | 0x22 | 1 byte |
+ | | Distributor Page | | |
+ ---------------------------------------------------------------
+ | 16 | ATM Globtal | 0x28 | 1 byte |
+ | | Params Table | | |
+ ---------------------------------------------------------------
+ | 20 | Insert Frame | 0xF8 | 4 bytes |
+ ---------------------------------------------------------------
+
+
+Extended Modes
+
+This is a double word bit array (64 bits) that defines special functionality
+which has an impact on the softwarew drivers. Each bit has its own impact
+and has special instructions for the s/w associated with it. This structure is
+described in this table:
+
+ -----------------------------------------------------------------------
+ | Bit # | Name | Description |
+ -----------------------------------------------------------------------
+ | 0 | General | Indicates that prior to each host command |
+ | | push command | given by the application, the software must |
+ | | | assert a special host command (push command)|
+ | | | CECDR = 0x00800000. |
+ | | | CECR = 0x01c1000f. |
+ -----------------------------------------------------------------------
+ | 1 | UCC ATM | Indicates that after issuing ATM RX INIT |
+ | | RX INIT | command, the host must issue another special|
+ | | push command | command (push command) and immediately |
+ | | | following that re-issue the ATM RX INIT |
+ | | | command. (This makes the sequence of |
+ | | | initializing the ATM receiver a sequence of |
+ | | | three host commands) |
+ | | | CECDR = 0x00800000. |
+ | | | CECR = 0x01c1000f. |
+ -----------------------------------------------------------------------
+ | 2 | Add/remove | Indicates that following the specific host |
+ | | command | command: "Add/Remove entry in Hash Lookup |
+ | | validation | Table" used in Interworking setup, the user |
+ | | | must issue another command. |
+ | | | CECDR = 0xce000003. |
+ | | | CECR = 0x01c10f58. |
+ -----------------------------------------------------------------------
+ | 3 | General push | Indicates that the s/w has to initialize |
+ | | command | some pointers in the Ethernet thread pages |
+ | | | which are used when Header Compression is |
+ | | | activated. The full details of these |
+ | | | pointers is located in the software drivers.|
+ -----------------------------------------------------------------------
+ | 4 | General push | Indicates that after issuing Ethernet TX |
+ | | command | INIT command, user must issue this command |
+ | | | for each SNUM of Ethernet TX thread. |
+ | | | CECDR = 0x00800003. |
+ | | | CECR = 0x7'b{0}, 8'b{Enet TX thread SNUM}, |
+ | | | 1'b{1}, 12'b{0}, 4'b{1} |
+ -----------------------------------------------------------------------
+ | 5 - 31 | N/A | Reserved, set to zero. |
+ -----------------------------------------------------------------------
+
+V - Firmware Structure Layout
+==============================
+
+QE microcode from Freescale is typically provided as a header file. This
+header file contains macros that define the microcode binary itself as well as
+some other data used in uploading that microcode. The format of these files
+do not lend themselves to simple inclusion into other code. Hence,
+the need for a more portable format. This section defines that format.
+
+Instead of distributing a header file, the microcode and related data are
+embedded into a binary blob. This blob is passed to the qe_upload_firmware()
+function, which parses the blob and performs everything necessary to upload
+the microcode.
+
+All integers are big-endian. See the comments for function
+qe_upload_firmware() for up-to-date implementation information.
+
+This structure supports versioning, where the version of the structure is
+embedded into the structure itself. To ensure forward and backwards
+compatibility, all versions of the structure must use the same 'qe_header'
+structure at the beginning.
+
+'header' (type: struct qe_header):
+ The 'length' field is the size, in bytes, of the entire structure,
+ including all the microcode embedded in it, as well as the CRC (if
+ present).
+
+ The 'magic' field is an array of three bytes that contains the letters
+ 'Q', 'E', and 'F'. This is an identifier that indicates that this
+ structure is a QE Firmware structure.
+
+ The 'version' field is a single byte that indicates the version of this
+ structure. If the layout of the structure should ever need to be
+ changed to add support for additional types of microcode, then the
+ version number should also be changed.
+
+The 'id' field is a null-terminated string(suitable for printing) that
+identifies the firmware.
+
+The 'count' field indicates the number of 'microcode' structures. There
+must be one and only one 'microcode' structure for each RISC processor.
+Therefore, this field also represents the number of RISC processors for this
+SOC.
+
+The 'soc' structure contains the SOC numbers and revisions used to match
+the microcode to the SOC itself. Normally, the microcode loader should
+check the data in this structure with the SOC number and revisions, and
+only upload the microcode if there's a match. However, this check is not
+made on all platforms.
+
+Although it is not recommended, you can specify '0' in the soc.model
+field to skip matching SOCs altogether.
+
+The 'model' field is a 16-bit number that matches the actual SOC. The
+'major' and 'minor' fields are the major and minor revision numbrs,
+respectively, of the SOC.
+
+For example, to match the 8323, revision 1.0:
+ soc.model = 8323
+ soc.major = 1
+ soc.minor = 0
+
+'padding' is neccessary for structure alignment. This field ensures that the
+'extended_modes' field is aligned on a 64-bit boundary.
+
+'extended_modes' is a bitfield that defines special functionality which has an
+impact on the device drivers. Each bit has its own impact and has special
+instructions for the driver associated with it. This field is stored in
+the QE library and available to any driver that calles qe_get_firmware_info().
+
+'vtraps' is an array of 8 words that contain virtual trap values for each
+virtual traps. As with 'extended_modes', this field is stored in the QE
+library and available to any driver that calles qe_get_firmware_info().
+
+'microcode' (type: struct qe_microcode):
+ For each RISC processor there is one 'microcode' structure. The first
+ 'microcode' structure is for the first RISC, and so on.
+
+ The 'id' field is a null-terminated string suitable for printing that
+ identifies this particular microcode.
+
+ 'traps' is an array of 16 words that contain hardware trap values
+ for each of the 16 traps. If trap[i] is 0, then this particular
+ trap is to be ignored (i.e. not written to TIBCR[i]). The entire value
+ is written as-is to the TIBCR[i] register, so be sure to set the EN
+ and T_IBP bits if necessary.
+
+ 'eccr' is the value to program into the ECCR register.
+
+ 'iram_offset' is the offset into IRAM to start writing the
+ microcode.
+
+ 'count' is the number of 32-bit words in the microcode.
+
+ 'code_offset' is the offset, in bytes, from the beginning of this
+ structure where the microcode itself can be found. The first
+ microcode binary should be located immediately after the 'microcode'
+ array.
+
+ 'major', 'minor', and 'revision' are the major, minor, and revision
+ version numbers, respectively, of the microcode. If all values are 0,
+ then these fields are ignored.
+
+ 'reserved' is necessary for structure alignment. Since 'microcode'
+ is an array, the 64-bit 'extended_modes' field needs to be aligned
+ on a 64-bit boundary, and this can only happen if the size of
+ 'microcode' is a multiple of 8 bytes. To ensure that, we add
+ 'reserved'.
+
+After the last microcode is a 32-bit CRC. It can be calculated using
+this algorithm:
+
+u32 crc32(const u8 *p, unsigned int len)
+{
+ unsigned int i;
+ u32 crc = 0;
+
+ while (len--) {
+ crc ^= *p++;
+ for (i = 0; i < 8; i++)
+ crc = (crc >> 1) ^ ((crc & 1) ? 0xedb88320 : 0);
+ }
+ return crc;
+}
+
+VI - Sample Code for Creating Firmware Files
+============================================
+
+A Python program that creates firmware binaries from the header files normally
+distributed by Freescale can be found on http://opensource.freescale.com.
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 53d0955..9ae800d 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -140,6 +140,9 @@
Used to allow a board to specify it wants a uImage built by default
default n
+config REDBOOT
+ bool
+
config PPC64_SWSUSP
bool
depends on PPC64 && (BROKEN || (PPC_PMAC64 && EXPERIMENTAL))
diff --git a/arch/powerpc/boot/.gitignore b/arch/powerpc/boot/.gitignore
index b160322..5ef2bdf 100644
--- a/arch/powerpc/boot/.gitignore
+++ b/arch/powerpc/boot/.gitignore
@@ -31,6 +31,7 @@
zImage.miboot
zImage.pmac
zImage.pseries
+zImage.redboot*
zImage.sandpoint
zImage.vmode
zconf.h
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index d1e625c..1e20aca 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -57,12 +57,12 @@
4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
fsl-soc.c mpc8xx.c pq2.c
-src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
+src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c \
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c \
- cuboot-katmai.c cuboot-rainier.c
+ cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -195,7 +195,9 @@
image-$(CONFIG_PPC_EP88XC) += zImage.ep88xc
image-$(CONFIG_EP405) += zImage.ep405
image-$(CONFIG_8260) += cuImage.pq2
+image-$(CONFIG_EP8248E) += zImage.ep8248e
image-$(CONFIG_PPC_MPC52xx) += cuImage.52xx
+image-$(CONFIG_STORCENTER) += cuImage.824x
image-$(CONFIG_PPC_83xx) += cuImage.83xx
image-$(CONFIG_PPC_85xx) += cuImage.85xx
image-$(CONFIG_MPC7448HPC2) += cuImage.hpc2
@@ -208,6 +210,10 @@
image-$(CONFIG_KATMAI) += cuImage.katmai
endif
+ifneq ($(CONFIG_REDBOOT),"")
+image-$(CONFIG_PPC_8xx) += zImage.redboot-8xx
+endif
+
# For 32-bit powermacs, build the COFF and miboot images
# as well as the ELF images.
ifeq ($(CONFIG_PPC32),y)
diff --git a/arch/powerpc/boot/cuboot-824x.c b/arch/powerpc/boot/cuboot-824x.c
new file mode 100644
index 0000000..ced90c5
--- /dev/null
+++ b/arch/powerpc/boot/cuboot-824x.c
@@ -0,0 +1,53 @@
+/*
+ * Old U-boot compatibility for 824x
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "cuboot.h"
+
+#define TARGET_824x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+
+static void platform_fixups(void)
+{
+ void *soc;
+
+ dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+ dt_fixup_mac_addresses(bd.bi_enetaddr);
+ dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 4, bd.bi_busfreq);
+
+ soc = find_node_by_devtype(NULL, "soc");
+ if (soc) {
+ void *serial = NULL;
+
+ setprop(soc, "bus-frequency", &bd.bi_busfreq,
+ sizeof(bd.bi_busfreq));
+
+ while ((serial = find_node_by_devtype(serial, "serial"))) {
+ if (get_parent(serial) != soc)
+ continue;
+
+ setprop(serial, "clock-frequency", &bd.bi_busfreq,
+ sizeof(bd.bi_busfreq));
+ }
+ }
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+ fdt_init(_dtb_start);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+}
diff --git a/arch/powerpc/boot/cuboot-83xx.c b/arch/powerpc/boot/cuboot-83xx.c
index acd860e..61af1c1 100644
--- a/arch/powerpc/boot/cuboot-83xx.c
+++ b/arch/powerpc/boot/cuboot-83xx.c
@@ -24,7 +24,8 @@
void *soc;
dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
- dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 4, bd.bi_busfreq);
/* Unfortunately, the specific model number is encoded in the
diff --git a/arch/powerpc/boot/cuboot-85xx.c b/arch/powerpc/boot/cuboot-85xx.c
index 943779e..6776a1a 100644
--- a/arch/powerpc/boot/cuboot-85xx.c
+++ b/arch/powerpc/boot/cuboot-85xx.c
@@ -24,8 +24,9 @@
void *soc;
dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
- dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr,
- bd.bi_enet2addr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
+ dt_fixup_mac_address_by_alias("ethernet2", bd.bi_enet2addr);
dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 8, bd.bi_busfreq);
/* Unfortunately, the specific model number is encoded in the
diff --git a/arch/powerpc/boot/devtree.c b/arch/powerpc/boot/devtree.c
index e5dfe44..60f561e 100644
--- a/arch/powerpc/boot/devtree.c
+++ b/arch/powerpc/boot/devtree.c
@@ -88,6 +88,20 @@
}
}
+void dt_fixup_mac_address_by_alias(const char *alias, const u8 *addr)
+{
+ void *devp = find_node_by_alias(alias);
+
+ if (devp) {
+ printf("%s: local-mac-address <-"
+ " %02x:%02x:%02x:%02x:%02x:%02x\n\r", alias,
+ addr[0], addr[1], addr[2],
+ addr[3], addr[4], addr[5]);
+
+ setprop(devp, "local-mac-address", addr, 6);
+ }
+}
+
void dt_fixup_mac_address(u32 index, const u8 *addr)
{
void *devp = find_node_by_prop_value(NULL, "linux,network-index",
diff --git a/arch/powerpc/boot/dts/adder875-redboot.dts b/arch/powerpc/boot/dts/adder875-redboot.dts
new file mode 100644
index 0000000..930bfb3
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-redboot.dts
@@ -0,0 +1,184 @@
+/*
+ * Device Tree Source for MPC885 ADS running RedBoot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ console = &console;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <15 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x01000000>;
+ };
+
+ localbus@fa200100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xfa200100 0x40>;
+
+ ranges = <
+ 0 0 0xfe000000 0x00800000
+ 2 0 0xfa100000 0x00008000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ bank-width = <2>;
+ device-width = <2>;
+ };
+ };
+
+ soc@fa200000 {
+ compatible = "fsl,mpc875-immr", "fsl,pq1-soc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xfa200000 0x00004000>;
+
+ // Temporary until code stops depending on it.
+ device_type = "soc";
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <0xfa200000 0x4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <0xe00 0x188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ eth0: ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0xe00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ eth1: ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0x1e00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1", "simple-bus";
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <0x9c0 0x40>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2000 0x2000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1c00>;
+ };
+ };
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <0x9f0 0x10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <0x930 0x20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ console: serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <0xa80 0x10 0x3e80 0x40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &console;
+ };
+};
diff --git a/arch/powerpc/boot/dts/adder875-uboot.dts b/arch/powerpc/boot/dts/adder875-uboot.dts
new file mode 100644
index 0000000..0197242
--- /dev/null
+++ b/arch/powerpc/boot/dts/adder875-uboot.dts
@@ -0,0 +1,183 @@
+/*
+ * Device Tree Source for MPC885 ADS running U-Boot
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "Analogue & Micro Adder MPC875";
+ compatible = "analogue-and-micro,adder875";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ console = &console;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,875@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ interrupts = <15 2>; // decrementer interrupt
+ interrupt-parent = <&PIC>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x01000000>;
+ };
+
+ localbus@ff000100 {
+ compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xff000100 0x40>;
+
+ ranges = <
+ 0 0 0xfe000000 0x01000000
+ >;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ bank-width = <2>;
+ device-width = <2>;
+ };
+ };
+
+ soc@ff000000 {
+ compatible = "fsl,mpc875-immr", "fsl,pq1-soc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xff000000 0x00004000>;
+
+ // Temporary until code stops depending on it.
+ device_type = "soc";
+
+ // Temporary until get_immrbase() is fixed.
+ reg = <0xff000000 0x4000>;
+
+ mdio@e00 {
+ compatible = "fsl,mpc875-fec-mdio", "fsl,pq1-fec-mdio";
+ reg = <0xe00 0x188>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PHY0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ eth0: ethernet@e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0xe00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <3 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ };
+
+ eth1: ethernet@1e00 {
+ device_type = "network";
+ compatible = "fsl,mpc875-fec-enet",
+ "fsl,pq1-fec-enet";
+ reg = <0x1e00 0x188>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <7 1>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ };
+
+ PIC: interrupt-controller@0 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x24>;
+ compatible = "fsl,mpc875-pic", "fsl,pq1-pic";
+ };
+
+ cpm@9c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc875-cpm", "fsl,cpm1", "simple-bus";
+ interrupts = <0>; // cpm error interrupt
+ interrupt-parent = <&CPM_PIC>;
+ reg = <0x9c0 0x40>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2000 0x2000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1c00>;
+ };
+ };
+
+ brg@9f0 {
+ compatible = "fsl,mpc875-brg",
+ "fsl,cpm1-brg",
+ "fsl,cpm-brg";
+ reg = <0x9f0 0x10>;
+ };
+
+ CPM_PIC: interrupt-controller@930 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <&PIC>;
+ reg = <0x930 0x20>;
+ compatible = "fsl,mpc875-cpm-pic",
+ "fsl,cpm1-pic";
+ };
+
+ console: serial@a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc875-smc-uart",
+ "fsl,cpm1-smc-uart";
+ reg = <0xa80 0x10 0x3e80 0x40>;
+ interrupts = <4>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x0090>;
+ current-speed = <115200>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &console;
+ };
+};
diff --git a/arch/powerpc/boot/dts/ep8248e.dts b/arch/powerpc/boot/dts/ep8248e.dts
new file mode 100644
index 0000000..5d2fb76
--- /dev/null
+++ b/arch/powerpc/boot/dts/ep8248e.dts
@@ -0,0 +1,207 @@
+/*
+ * Device Tree for the Embedded Planet EP8248E board running PlanetCore.
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "EP8248E";
+ compatible = "fsl,ep8248e";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ planetcore-SMC1 = &smc1;
+ planetcore-SCC1 = &scc1;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ serial0 = &smc1;
+ serial1 = &scc1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8248@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <16384>;
+ i-cache-size = <16384>;
+ timebase-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ localbus@f0010100 {
+ compatible = "fsl,mpc8248-localbus",
+ "fsl,pq2-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xf0010100 0x40>;
+
+ ranges = <0 0 0xfc000000 0x04000000
+ 1 0 0xfa000000 0x00008000>;
+
+ flash@0,3800000 {
+ compatible = "cfi-flash";
+ reg = <0 0x3800000 0x800000>;
+ bank-width = <4>;
+ device-width = <2>;
+ };
+
+ bcsr@1,0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <1 0 0x10>;
+ compatible = "fsl,ep8248e-bcsr";
+ ranges;
+
+ mdio {
+ device_type = "mdio";
+ compatible = "fsl,ep8248e-mdio-bitbang";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1 8 1>;
+
+ PHY0: ethernet-phy@0 {
+ interrupt-parent = <&PIC>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&PIC>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0>;
+ };
+
+ soc@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8248-immr", "fsl,pq2-soc", "simple-bus";
+ ranges = <0x00000000 0xf0000000 0x00053000>;
+
+ // Temporary until code stops depending on it.
+ device_type = "soc";
+
+ // Temporary -- will go away once kernel uses ranges for get_immrbase().
+ reg = <0xf0000000 0x00053000>;
+
+ cpm@119c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,mpc8248-cpm", "fsl,cpm2",
+ "simple-bus";
+ reg = <0x119c0 0x30>;
+ ranges;
+
+ muram {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 0x1100 0x1140
+ 0xec0 0x9800 0x800>;
+ };
+ };
+
+ brg@119f0 {
+ compatible = "fsl,mpc8248-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <0x119f0 0x10 0x115f0 0x10>;
+ };
+
+ /* Monitor port/SMC1 */
+ smc1: serial@11a80 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-smc-uart",
+ "fsl,cpm2-smc-uart";
+ reg = <0x11a80 0x20 0x1100 0x40>;
+ interrupts = <4 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <7>;
+ fsl,cpm-command = <0x1d000000>;
+ linux,planetcore-label = "SMC1";
+ };
+
+ /* "Serial" port/SCC1 */
+ scc1: serial@11a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8248-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <0x11a00 0x20 0x8000 0x100>;
+ interrupts = <40 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <0x00800000>;
+ linux,planetcore-label = "SCC1";
+ };
+
+ eth0: ethernet@11300 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x11300 0x20 0x8400 0x100 0x11390 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <32 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ linux,network-index = <0>;
+ fsl,cpm-command = <0x12000300>;
+ };
+
+ eth1: ethernet@11320 {
+ device_type = "network";
+ compatible = "fsl,mpc8248-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <0x11320 0x20 0x8500 0x100 0x113b0 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <33 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY1>;
+ linux,network-index = <1>;
+ fsl,cpm-command = <0x16200300>;
+ };
+
+ usb@11b60 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8248-usb",
+ "fsl,cpm2-usb";
+ reg = <0x11b60 0x18 0x8b00 0x100>;
+ interrupt-parent = <&PIC>;
+ interrupts = <11 8>;
+ fsl,cpm-command = <0x2e600000>;
+ };
+ };
+
+ PIC: interrupt-controller@10c00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <0x10c00 0x80>;
+ compatible = "fsl,mpc8248-pic", "fsl,pq2-pic";
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8313erdb.dts b/arch/powerpc/boot/dts/mpc8313erdb.dts
index c5b6665..9bcf2c9 100644
--- a/arch/powerpc/boot/dts/mpc8313erdb.dts
+++ b/arch/powerpc/boot/dts/mpc8313erdb.dts
@@ -45,10 +45,58 @@
reg = <00000000 08000000>; // 128MB at 0
};
+ localbus@e0005000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8313-elbc", "fsl,elbc", "simple-bus";
+ reg = <e0005000 1000>;
+ interrupts = <d#77 8>;
+ interrupt-parent = <&ipic>;
+
+ // CS0 and CS1 are swapped when
+ // booting from nand, but the
+ // addresses are the same.
+ ranges = <0 0 fe000000 00800000
+ 1 0 e2800000 00008000
+ 2 0 f0000000 00020000
+ 3 0 fa000000 00008000>;
+
+ flash@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0 0 800000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8313-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <1 0 2000>;
+
+ u-boot@0 {
+ reg = <0 100000>;
+ read-only;
+ };
+
+ kernel@100000 {
+ reg = <100000 300000>;
+ };
+
+ fs@400000 {
+ reg = <400000 1c00000>;
+ };
+ };
+ };
+
soc8313@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0 e0000000 00100000>;
reg = <e0000000 00000200>;
bus-frequency = <0>;
@@ -92,7 +140,6 @@
/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
usb@23000 {
- device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 26ac467..6902524 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -7,6 +7,18 @@
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+
+ * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
+ * this:
+ *
+ * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
+ * 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
+ * next to the serial ports.
+ * 3) Solder a wire from U61-22 to P19K-22.
+ *
+ * Note that there's a typo in the schematic. The board labels the last column
+ * of pins "P19K", but in the schematic, that column is called "P19J". So if
+ * you're going by the schematic, the pin is called "P19J-K22".
*/
/ {
@@ -169,6 +181,23 @@
1 1e 1 0 1 0 /* TX_EN */
1 1f 2 0 1 0>;/* CRS */
};
+ pio5: ucc_pin@05 {
+ pio-map = <
+ /*
+ * open has
+ * port pin dir drain sel irq
+ */
+ 2 0 1 0 2 0 /* TxD5 */
+ 2 8 2 0 2 0 /* RxD5 */
+
+ 2 1d 2 0 0 0 /* CTS5 */
+ 2 1f 1 0 2 0 /* RTS5 */
+
+ 2 18 2 0 0 0 /* CD */
+
+ >;
+ };
+
};
};
@@ -176,6 +205,7 @@
#address-cells = <1>;
#size-cells = <1>;
device_type = "qe";
+ compatible = "fsl,qe";
model = "QE";
ranges = <0 e0100000 00100000>;
reg = <e0100000 480>;
@@ -210,7 +240,6 @@
};
usb@6c0 {
- device_type = "usb";
compatible = "qe_udc";
reg = <6c0 40 8B00 100>;
interrupts = <b>;
@@ -250,6 +279,26 @@
pio-handle = < &pio4 >;
};
+ ucc@2400 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ model = "UCC";
+ device-id = <5>; /* The UCC number, 1-7*/
+ port-number = <0>; /* Which ttyQEx device */
+ soft-uart; /* We need Soft-UART */
+ reg = <2400 200>;
+ interrupts = <28>; /* From Table 18-12 */
+ interrupt-parent = < &qeic >;
+ /*
+ * For Soft-UART, we need to set TX to 1X, which
+ * means specifying separate clock sources.
+ */
+ rx-clock-name = "brg5";
+ tx-clock-name = "brg6";
+ pio-handle = < &pio5 >;
+ };
+
+
mdio@2320 {
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts
index e354f26..04b8da4 100644
--- a/arch/powerpc/boot/dts/mpc8349emitx.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitx.dts
@@ -91,7 +91,6 @@
};
usb@22000 {
- device_type = "usb";
compatible = "fsl-usb2-mph";
reg = <22000 1000>;
#address-cells = <1>;
@@ -103,7 +102,6 @@
};
usb@23000 {
- device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
@@ -127,14 +125,6 @@
reg = <1c>;
device_type = "ethernet-phy";
};
-
- /* Vitesse 7385 */
- phy1f: ethernet-phy@1f {
- interrupt-parent = < &ipic >;
- interrupts = <12 8>;
- reg = <1f>;
- device_type = "ethernet-phy";
- };
};
enet0: ethernet@24000 {
@@ -159,7 +149,8 @@
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <23 8 24 8 25 8>;
interrupt-parent = < &ipic >;
- phy-handle = < &phy1f >;
+ /* Vitesse 7385 isn't on the MDIO bus */
+ fixed-link = <1 1 d#1000 0 0>;
linux,network-index = <1>;
};
@@ -253,6 +244,21 @@
device_type = "pci";
};
+ localbus@e0005000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349e-localbus",
+ "fsl,pq2pro-localbus";
+ reg = <e0005000 d8>;
+ ranges = <3 0 f0000000 210>;
-
+ pata@3,0 {
+ compatible = "fsl,mpc8349emitx-pata", "ata-generic";
+ reg = <3 0 10 3 20c 4>;
+ reg-shift = <1>;
+ pio-mode = <6>;
+ interrupts = <17 8>;
+ interrupt-parent = <&ipic>;
+ };
+ };
};
diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
index ebdf0b7..a06ff92 100644
--- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
@@ -89,7 +89,6 @@
};
usb@23000 {
- device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts
index 0ba13eb..4120e92 100644
--- a/arch/powerpc/boot/dts/mpc834x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc834x_mds.dts
@@ -104,7 +104,6 @@
/* phy type (ULPI or SERIAL) are only types supportted for MPH */
/* port = 0 or 1 */
usb@22000 {
- device_type = "usb";
compatible = "fsl-usb2-mph";
reg = <22000 1000>;
#address-cells = <1>;
@@ -116,7 +115,6 @@
};
/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
usb@23000 {
- device_type = "usb";
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index fd841b2..2181d2c 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -241,7 +241,6 @@
};
usb@6c0 {
- device_type = "usb";
compatible = "qe_udc";
reg = <6c0 40 8B00 100>;
interrupts = <b>;
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
new file mode 100644
index 0000000..98b4606
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -0,0 +1,279 @@
+/*
+ * MPC8377E MDS Device Tree Source
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "fsl,mpc8377emds";
+ compatible = "fsl,mpc8377emds","fsl,mpc837xmds";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8377@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <0x20>;
+ i-cache-line-size = <0x20>;
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; // 512MB at 0
+ };
+
+ soc@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x0 0xe0000000 0x00100000>;
+ reg = <0xe0000000 0x00000200>;
+ bus-frequency = <0>;
+
+ wdt@200 {
+ compatible = "mpc83xx_wdt";
+ reg = <0x200 0x100>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <0xe 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <0xf 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ spi@7000 {
+ compatible = "fsl_spi";
+ reg = <0x7000 0x1000>;
+ interrupts = <0x10 0x8>;
+ interrupt-parent = < &ipic >;
+ mode = "cpu";
+ };
+
+ /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
+ usb@23000 {
+ compatible = "fsl-usb2-dr";
+ reg = <0x23000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x26 0x8>;
+ phy_type = "utmi_wide";
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+ phy2: ethernet-phy@2 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x11 0x8>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x12 0x8>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x20 0x8 0x21 0x8 0x22 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy2 >;
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x23 0x8 0x24 0x8 0x25 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy3 >;
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0x9 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0xa 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ crypto@30000 {
+ model = "SEC3";
+ compatible = "talitos";
+ reg = <0x30000 0x10000>;
+ interrupts = <0xb 0x8>;
+ interrupt-parent = < &ipic >;
+ /* Rev. 3.0 geometry */
+ num-channels = <4>;
+ channel-fifo-len = <0x18>;
+ exec-units-mask = <0x000001fe>;
+ descriptor-types-mask = <0x03ab0ebf>;
+ };
+
+ sdhc@2e000 {
+ model = "eSDHC";
+ compatible = "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <0x2a 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@18000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x18000 0x1000>;
+ interrupts = <0x2c 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@19000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x19000 0x1000>;
+ interrupts = <0x2d 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ /* IPIC
+ * interrupts cell = <intr #, sense>
+ * sense values match linux IORESOURCE_IRQ_* defines:
+ * sense == 8: Level, low assertion
+ * sense == 2: Edge, high-to-low change
+ */
+ ipic: pic@700 {
+ compatible = "fsl,ipic";
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x700 0x100>;
+ };
+ };
+
+ pci0: pci@e0008500 {
+ cell-index = <0>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+
+ /* IDSEL 0x11 */
+ 0x8800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0x8800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0x8800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0x8800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x12 */
+ 0x9000 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0x9000 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0x9000 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0x9000 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x13 */
+ 0x9800 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0x9800 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0x9800 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0x9800 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x15 */
+ 0xa800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0xa800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0xa800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0xa800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x16 */
+ 0xb000 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0xb000 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0xb000 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0xb000 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x17 */
+ 0xb800 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0xb800 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0xb800 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0xb800 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x18 */
+ 0xc000 0x0 0x0 0x1 &ipic 0x15 0x8
+ 0xc000 0x0 0x0 0x2 &ipic 0x16 0x8
+ 0xc000 0x0 0x0 0x3 &ipic 0x17 0x8
+ 0xc000 0x0 0x0 0x4 &ipic 0x14 0x8>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x42 0x8>;
+ bus-range = <0 0>;
+ ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+ 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
+ clock-frequency = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xe0008500 0x100>;
+ compatible = "fsl,mpc8349-pci";
+ device_type = "pci";
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
new file mode 100644
index 0000000..c117a6a
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -0,0 +1,265 @@
+/*
+ * MPC8378E MDS Device Tree Source
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "fsl,mpc8378emds";
+ compatible = "fsl,mpc8378emds","fsl,mpc837xmds";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8378@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <0x20>;
+ i-cache-line-size = <0x20>;
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; // 512MB at 0
+ };
+
+ soc@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x0 0xe0000000 0x00100000>;
+ reg = <0xe0000000 0x00000200>;
+ bus-frequency = <0>;
+
+ wdt@200 {
+ compatible = "mpc83xx_wdt";
+ reg = <0x200 0x100>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <0xe 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <0xf 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ spi@7000 {
+ compatible = "fsl_spi";
+ reg = <0x7000 0x1000>;
+ interrupts = <0x10 0x8>;
+ interrupt-parent = < &ipic >;
+ mode = "cpu";
+ };
+
+ /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
+ usb@23000 {
+ compatible = "fsl-usb2-dr";
+ reg = <0x23000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x26 0x8>;
+ phy_type = "utmi_wide";
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+ phy2: ethernet-phy@2 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x11 0x8>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x12 0x8>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x20 0x8 0x21 0x8 0x22 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy2 >;
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x23 0x8 0x24 0x8 0x25 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy3 >;
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0x9 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0xa 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ crypto@30000 {
+ model = "SEC3";
+ compatible = "talitos";
+ reg = <0x30000 0x10000>;
+ interrupts = <0xb 0x8>;
+ interrupt-parent = < &ipic >;
+ /* Rev. 3.0 geometry */
+ num-channels = <4>;
+ channel-fifo-len = <0x18>;
+ exec-units-mask = <0x000001fe>;
+ descriptor-types-mask = <0x03ab0ebf>;
+ };
+
+ sdhc@2e000 {
+ model = "eSDHC";
+ compatible = "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <0x2a 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ /* IPIC
+ * interrupts cell = <intr #, sense>
+ * sense values match linux IORESOURCE_IRQ_* defines:
+ * sense == 8: Level, low assertion
+ * sense == 2: Edge, high-to-low change
+ */
+ ipic: pic@700 {
+ compatible = "fsl,ipic";
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x700 0x100>;
+ };
+ };
+
+ pci0: pci@e0008500 {
+ cell-index = <0>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+
+ /* IDSEL 0x11 */
+ 0x8800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0x8800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0x8800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0x8800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x12 */
+ 0x9000 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0x9000 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0x9000 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0x9000 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x13 */
+ 0x9800 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0x9800 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0x9800 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0x9800 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x15 */
+ 0xa800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0xa800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0xa800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0xa800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x16 */
+ 0xb000 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0xb000 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0xb000 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0xb000 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x17 */
+ 0xb800 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0xb800 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0xb800 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0xb800 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x18 */
+ 0xc000 0x0 0x0 0x1 &ipic 0x15 0x8
+ 0xc000 0x0 0x0 0x2 &ipic 0x16 0x8
+ 0xc000 0x0 0x0 0x3 &ipic 0x17 0x8
+ 0xc000 0x0 0x0 0x4 &ipic 0x14 0x8>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x42 0x8>;
+ bus-range = <0 0>;
+ ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+ 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
+ clock-frequency = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xe0008500 0x100>;
+ compatible = "fsl,mpc8349-pci";
+ device_type = "pci";
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts
new file mode 100644
index 0000000..fc3ba79
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc8379_mds.dts
@@ -0,0 +1,293 @@
+/*
+ * MPC8379E MDS Device Tree Source
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "fsl,mpc8379emds";
+ compatible = "fsl,mpc8379emds","fsl,mpc837xmds";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8379@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <0x20>;
+ i-cache-line-size = <0x20>;
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; // 512MB at 0
+ };
+
+ soc@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x0 0xe0000000 0x00100000>;
+ reg = <0xe0000000 0x00000200>;
+ bus-frequency = <0>;
+
+ wdt@200 {
+ compatible = "mpc83xx_wdt";
+ reg = <0x200 0x100>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <0xe 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <0xf 0x8>;
+ interrupt-parent = < &ipic >;
+ dfsrr;
+ };
+
+ spi@7000 {
+ compatible = "fsl_spi";
+ reg = <0x7000 0x1000>;
+ interrupts = <0x10 0x8>;
+ interrupt-parent = < &ipic >;
+ mode = "cpu";
+ };
+
+ /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
+ usb@23000 {
+ compatible = "fsl-usb2-dr";
+ reg = <0x23000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x26 0x8>;
+ phy_type = "utmi_wide";
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+ phy2: ethernet-phy@2 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x11 0x8>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = < &ipic >;
+ interrupts = <0x12 0x8>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x20 0x8 0x21 0x8 0x22 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy2 >;
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <0x23 0x8 0x24 0x8 0x25 0x8>;
+ phy-connection-type = "mii";
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy3 >;
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0x9 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <0xa 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ crypto@30000 {
+ model = "SEC3";
+ compatible = "talitos";
+ reg = <0x30000 0x10000>;
+ interrupts = <0xb 0x8>;
+ interrupt-parent = < &ipic >;
+ /* Rev. 3.0 geometry */
+ num-channels = <4>;
+ channel-fifo-len = <0x18>;
+ exec-units-mask = <0x000001fe>;
+ descriptor-types-mask = <0x03ab0ebf>;
+ };
+
+ sdhc@2e000 {
+ model = "eSDHC";
+ compatible = "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <0x2a 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@18000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x18000 0x1000>;
+ interrupts = <0x2c 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@19000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x19000 0x1000>;
+ interrupts = <0x2d 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@1a000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x1a000 0x1000>;
+ interrupts = <0x2e 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sata@1b000 {
+ compatible = "fsl,mpc8379-sata";
+ reg = <0x1b000 0x1000>;
+ interrupts = <0x2f 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ /* IPIC
+ * interrupts cell = <intr #, sense>
+ * sense values match linux IORESOURCE_IRQ_* defines:
+ * sense == 8: Level, low assertion
+ * sense == 2: Edge, high-to-low change
+ */
+ ipic: pic@700 {
+ compatible = "fsl,ipic";
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x700 0x100>;
+ };
+ };
+
+ pci0: pci@e0008500 {
+ cell-index = <0>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+
+ /* IDSEL 0x11 */
+ 0x8800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0x8800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0x8800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0x8800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x12 */
+ 0x9000 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0x9000 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0x9000 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0x9000 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x13 */
+ 0x9800 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0x9800 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0x9800 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0x9800 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x15 */
+ 0xa800 0x0 0x0 0x1 &ipic 0x14 0x8
+ 0xa800 0x0 0x0 0x2 &ipic 0x15 0x8
+ 0xa800 0x0 0x0 0x3 &ipic 0x16 0x8
+ 0xa800 0x0 0x0 0x4 &ipic 0x17 0x8
+
+ /* IDSEL 0x16 */
+ 0xb000 0x0 0x0 0x1 &ipic 0x17 0x8
+ 0xb000 0x0 0x0 0x2 &ipic 0x14 0x8
+ 0xb000 0x0 0x0 0x3 &ipic 0x15 0x8
+ 0xb000 0x0 0x0 0x4 &ipic 0x16 0x8
+
+ /* IDSEL 0x17 */
+ 0xb800 0x0 0x0 0x1 &ipic 0x16 0x8
+ 0xb800 0x0 0x0 0x2 &ipic 0x17 0x8
+ 0xb800 0x0 0x0 0x3 &ipic 0x14 0x8
+ 0xb800 0x0 0x0 0x4 &ipic 0x15 0x8
+
+ /* IDSEL 0x18 */
+ 0xc000 0x0 0x0 0x1 &ipic 0x15 0x8
+ 0xc000 0x0 0x0 0x2 &ipic 0x16 0x8
+ 0xc000 0x0 0x0 0x3 &ipic 0x17 0x8
+ 0xc000 0x0 0x0 0x4 &ipic 0x14 0x8>;
+ interrupt-parent = < &ipic >;
+ interrupts = <0x42 0x8>;
+ bus-range = <0 0>;
+ ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+ 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
+ clock-frequency = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xe0008500 0x100>;
+ compatible = "fsl,mpc8349-pci";
+ device_type = "pci";
+ };
+};
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 54b3bdf..688af9d 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -304,9 +304,9 @@
interrupt-map = <
// IDSEL 0x1c USB
e000 0 0 1 &i8259 c 2
- e100 0 0 1 &i8259 9 2
- e200 0 0 1 &i8259 a 2
- e300 0 0 1 &i8259 b 2
+ e100 0 0 2 &i8259 9 2
+ e200 0 0 3 &i8259 a 2
+ e300 0 0 4 &i8259 b 2
// IDSEL 0x1d Audio
e800 0 0 1 &i8259 6 2
diff --git a/arch/powerpc/boot/dts/mpc8572ds.dts b/arch/powerpc/boot/dts/mpc8572ds.dts
index 233e0d5..813c259 100644
--- a/arch/powerpc/boot/dts/mpc8572ds.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds.dts
@@ -334,9 +334,9 @@
// IDSEL 0x1c USB
e000 0 0 1 &i8259 c 2
- e100 0 0 1 &i8259 9 2
- e200 0 0 1 &i8259 a 2
- e300 0 0 1 &i8259 b 2
+ e100 0 0 2 &i8259 9 2
+ e200 0 0 3 &i8259 a 2
+ e300 0 0 4 &i8259 b 2
// IDSEL 0x1d Audio
e800 0 0 1 &i8259 6 2
@@ -481,6 +481,7 @@
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1b 2>;
+ interrupt-map-mask = <f800 0 0 7>;
interrupt-map = <
/* IDSEL 0x0 */
0000 0 0 1 &mpic 0 1
diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
index 01040a7..d98715c 100644
--- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts
+++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
@@ -1,7 +1,7 @@
/*
* MPC8610 HPCD Device Tree Source
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007-2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License Version 2 as published
@@ -49,6 +49,7 @@
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
+ compatible = "fsl,mpc8610-immr", "simple-bus";
ranges = <0 e0000000 00100000>;
reg = <e0000000 1000>;
bus-frequency = <0>;
@@ -62,6 +63,13 @@
interrupts = <2b 2>;
interrupt-parent = <&mpic>;
dfsrr;
+
+ cs4270:codec@4f {
+ compatible = "cirrus,cs4270";
+ reg = <4f>;
+ /* MCLK source is a stand-alone oscillator */
+ clock-frequency = <bb8000>;
+ };
};
i2c@3100 {
@@ -111,6 +119,109 @@
reg = <e0000 1000>;
fsl,has-rstcr;
};
+
+ i2s@16000 {
+ compatible = "fsl,mpc8610-ssi";
+ cell-index = <0>;
+ reg = <16000 100>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3e 2>;
+ fsl,mode = "i2s-slave";
+ codec-handle = <&cs4270>;
+ };
+
+ ssi@16100 {
+ compatible = "fsl,mpc8610-ssi";
+ cell-index = <1>;
+ reg = <16100 100>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3f 2>;
+ };
+
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8610-dma", "fsl,eloplus-dma";
+ cell-index = <0>;
+ reg = <21300 4>; /* DMA general status register */
+ ranges = <0 21100 200>;
+
+ dma-channel@0 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,eloplus-dma-channel";
+ cell-index = <0>;
+ reg = <0 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <14 2>;
+ };
+ dma-channel@1 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,eloplus-dma-channel";
+ cell-index = <1>;
+ reg = <80 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <15 2>;
+ };
+ dma-channel@2 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,eloplus-dma-channel";
+ cell-index = <2>;
+ reg = <100 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+ dma-channel@3 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,eloplus-dma-channel";
+ cell-index = <3>;
+ reg = <180 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <17 2>;
+ };
+ };
+
+ dma@c300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8610-dma", "fsl,mpc8540-dma";
+ cell-index = <1>;
+ reg = <c300 4>; /* DMA general status register */
+ ranges = <0 c100 200>;
+
+ dma-channel@0 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,mpc8540-dma-channel";
+ cell-index = <0>;
+ reg = <0 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3c 2>;
+ };
+ dma-channel@1 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,mpc8540-dma-channel";
+ cell-index = <1>;
+ reg = <80 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3d 2>;
+ };
+ dma-channel@2 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,mpc8540-dma-channel";
+ cell-index = <2>;
+ reg = <100 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3e 2>;
+ };
+ dma-channel@3 {
+ compatible = "fsl,mpc8610-dma-channel",
+ "fsl,mpc8540-dma-channel";
+ cell-index = <3>;
+ reg = <180 80>;
+ interrupt-parent = <&mpic>;
+ interrupts = <3f 2>;
+ };
+ };
+
};
pci0: pci@e0008000 {
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 86fc228..556a9ca 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -60,10 +60,52 @@
reg = <00000000 40000000>; // 1G at 0x0
};
+ localbus@f8005000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8641-localbus", "simple-bus";
+ reg = <f8005000 1000>;
+ interrupts = <13 2>;
+ interrupt-parent = <&mpic>;
+
+ ranges = <0 0 ff800000 00800000
+ 1 0 fe000000 01000000
+ 2 0 f8200000 00100000
+ 3 0 f8100000 00100000>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 00800000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "kernel";
+ reg = <00000000 00300000>;
+ };
+ partition@300000 {
+ label = "firmware b";
+ reg = <00300000 00100000>;
+ read-only;
+ };
+ partition@400000 {
+ label = "fs";
+ reg = <00400000 00300000>;
+ };
+ partition@700000 {
+ label = "firmware a";
+ reg = <00700000 00100000>;
+ read-only;
+ };
+ };
+ };
+
soc8641@f8000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <00000000 f8000000 00100000>;
reg = <f8000000 00001000>; // CCSRBAR
bus-frequency = <0>;
@@ -326,9 +368,9 @@
// IDSEL 0x1c USB
e000 0 0 1 &i8259 c 2
- e100 0 0 1 &i8259 9 2
- e200 0 0 1 &i8259 a 2
- e300 0 0 1 &i8259 b 2
+ e100 0 0 2 &i8259 9 2
+ e200 0 0 3 &i8259 a 2
+ e300 0 0 4 &i8259 b 2
// IDSEL 0x1d Audio
e800 0 0 1 &i8259 6 2
diff --git a/arch/powerpc/boot/dts/storcenter.dts b/arch/powerpc/boot/dts/storcenter.dts
new file mode 100644
index 0000000..6aa1d69
--- /dev/null
+++ b/arch/powerpc/boot/dts/storcenter.dts
@@ -0,0 +1,138 @@
+/*
+ * Device Tree Source for IOMEGA StorCenter
+ *
+ * Copyright 2007 Oyvind Repvik
+ * Copyright 2007 Jon Loeliger
+ *
+ * Based on the Kurobox DTS by G. Liakhovetski <g.liakhovetski@gmx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/ {
+ model = "StorCenter";
+ compatible = "storcenter";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8241@0 {
+ device_type = "cpu";
+ reg = <0>;
+ clock-frequency = <d# 200000000>; /* Hz */
+ timebase-frequency = <d# 25000000>; /* Hz */
+ bus-frequency = <0>; /* from bootwrapper */
+ i-cache-line-size = <d# 32>; /* bytes */
+ d-cache-line-size = <d# 32>; /* bytes */
+ i-cache-size = <4000>;
+ d-cache-size = <4000>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <00000000 04000000>; /* 64MB @ 0x0 */
+ };
+
+ soc@fc000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8241", "mpc10x";
+ store-gathering = <0>; /* 0 == off, !0 == on */
+ ranges = <0 fc000000 100000>;
+ reg = <fc000000 100000>; /* EUMB */
+ bus-frequency = <0>; /* fixed by loader */
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl-i2c";
+ reg = <3000 100>;
+ interrupts = <5 2>;
+ interrupt-parent = <&mpic>;
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <68>;
+ };
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4500 20>;
+ clock-frequency = <d# 97553800>; /* Hz */
+ current-speed = <d# 115200>;
+ interrupts = <9 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4600 20>;
+ clock-frequency = <d# 97553800>; /* Hz */
+ current-speed = <d# 9600>;
+ interrupts = <a 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ mpic: interrupt-controller@40000 {
+ #interrupt-cells = <2>;
+ device_type = "open-pic";
+ compatible = "chrp,open-pic";
+ interrupt-controller;
+ reg = <40000 40000>;
+ };
+
+ };
+
+ pci0: pci@fe800000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ compatible = "mpc10x-pci";
+ reg = <fe800000 1000>;
+ ranges = <01000000 0 0 fe000000 0 00c00000
+ 02000000 0 80000000 80000000 0 70000000>;
+ bus-range = <0 ff>;
+ clock-frequency = <d# 97553800>; /* Hz */
+ interrupt-parent = <&mpic>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 13 - IDE */
+ 6800 0 0 1 &mpic 0 1
+ 6800 0 0 2 &mpic 0 1
+ 6800 0 0 3 &mpic 0 1
+ /* IDSEL 14 - USB */
+ 7000 0 0 1 &mpic 0 1
+ 7000 0 0 2 &mpic 0 1
+ 7000 0 0 3 &mpic 0 1
+ 7000 0 0 4 &mpic 0 1
+ /* IDSEL 15 - ETH */
+ 7800 0 0 1 &mpic 0 1
+ 7800 0 0 2 &mpic 0 1
+ 7800 0 0 3 &mpic 0 1
+ 7800 0 0 4 &mpic 0 1
+ >;
+ };
+
+ chosen {
+ linux,stdout-path = "/soc/serial@4500";
+ };
+};
diff --git a/arch/powerpc/boot/ep8248e.c b/arch/powerpc/boot/ep8248e.c
new file mode 100644
index 0000000..f57d14d
--- /dev/null
+++ b/arch/powerpc/boot/ep8248e.c
@@ -0,0 +1,55 @@
+/*
+ * Embedded Planet EP8248E with PlanetCore firmware
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "planetcore.h"
+#include "pq2.h"
+
+static char *table;
+static u64 mem_size;
+
+#include <io.h>
+
+static void platform_fixups(void)
+{
+ u64 val;
+
+ dt_fixup_memory(0, mem_size);
+ planetcore_set_mac_addrs(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_CRYSTAL_HZ, &val)) {
+ printf("No PlanetCore crystal frequency key.\r\n");
+ return;
+ }
+
+ pq2_fixup_clocks(val);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ table = (char *)r3;
+ planetcore_prepare_table(table);
+
+ if (!planetcore_get_decimal(table, PLANETCORE_KEY_MB_RAM, &mem_size))
+ return;
+
+ mem_size *= 1024 * 1024;
+ simple_alloc_init(_end, mem_size - (unsigned long)_end, 32, 64);
+
+ fdt_init(_dtb_start);
+
+ planetcore_set_stdout_path(table);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+}
diff --git a/arch/powerpc/boot/ops.h b/arch/powerpc/boot/ops.h
index 6036a98..5872ef1 100644
--- a/arch/powerpc/boot/ops.h
+++ b/arch/powerpc/boot/ops.h
@@ -159,9 +159,23 @@
return find_node_by_prop_value_str(prev, "device_type", type);
}
+static inline void *find_node_by_alias(const char *alias)
+{
+ void *devp = finddevice("/aliases");
+
+ if (devp) {
+ char path[MAX_PATH_LEN];
+ if (getprop(devp, alias, path, MAX_PATH_LEN) > 0)
+ return finddevice(path);
+ }
+
+ return NULL;
+}
+
void dt_fixup_memory(u64 start, u64 size);
void dt_fixup_cpu_clocks(u32 cpufreq, u32 tbfreq, u32 busfreq);
void dt_fixup_clock(const char *path, u32 freq);
+void dt_fixup_mac_address_by_alias(const char *alias, const u8 *addr);
void dt_fixup_mac_address(u32 index, const u8 *addr);
void __dt_fixup_mac_addresses(u32 startindex, ...);
#define dt_fixup_mac_addresses(...) \
diff --git a/arch/powerpc/boot/redboot-8xx.c b/arch/powerpc/boot/redboot-8xx.c
new file mode 100644
index 0000000..f7945ad
--- /dev/null
+++ b/arch/powerpc/boot/redboot-8xx.c
@@ -0,0 +1,58 @@
+/*
+ * RedBoot firmware support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "redboot.h"
+#include "fsl-soc.h"
+#include "io.h"
+
+static bd_t bd;
+BSS_STACK(4096);
+
+#define MHZ(x) ((x + 500000) / 1000000)
+
+static void platform_fixups(void)
+{
+ void *node;
+
+ dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+ dt_fixup_mac_addresses(bd.bi_enetaddr);
+ dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 16, bd.bi_busfreq);
+
+ node = finddevice("/soc/cpm/brg");
+ if (node) {
+ printf("BRG clock-frequency <- 0x%x (%dMHz)\r\n",
+ bd.bi_busfreq, MHZ(bd.bi_busfreq));
+ setprop(node, "clock-frequency", &bd.bi_busfreq, 4);
+ }
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ memcpy(&bd, (char *)r3, sizeof(bd));
+
+ if (bd.bi_tag != 0x42444944)
+ return;
+
+ simple_alloc_init(_end,
+ bd.bi_memstart + bd.bi_memsize - (unsigned long)_end,
+ 32, 64);
+
+ fdt_init(_dtb_start);
+ serial_console_init();
+ platform_ops.fixups = platform_fixups;
+
+ loader_info.cmdline = (char *)bd.bi_cmdline;
+ loader_info.cmdline_len = strlen((char *)bd.bi_cmdline);
+}
diff --git a/arch/powerpc/boot/redboot.h b/arch/powerpc/boot/redboot.h
new file mode 100644
index 0000000..ace0b7f
--- /dev/null
+++ b/arch/powerpc/boot/redboot.h
@@ -0,0 +1,56 @@
+#ifndef _PPC_REDBOOT_H
+#define _PPC_REDBOOT_H
+
+//=========================================================================
+// include/asm-ppc/redboot.h
+// Copyright (c) 2002, 2003 Gary Thomas (<gary@mlbassoc.com>
+// Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+
+//
+// Board specific details, as provided by RedBoot
+//
+
+/* A Board Information structure that is given to a program when
+ * RedBoot starts it up. Note: not all fields make sense for all
+ * architectures and it's up to the platform specific code to fill
+ * in the details.
+ */
+typedef struct bd_info {
+ unsigned int bi_tag; /* Should be 0x42444944 "BDID" */
+ unsigned int bi_size; /* Size of this structure */
+ unsigned int bi_revision; /* revision of this structure */
+ unsigned int bi_bdate; /* bootstrap date, i.e. 0x19971106 */
+ unsigned int bi_memstart; /* Memory start address */
+ unsigned int bi_memsize; /* Memory (end) size in bytes */
+ unsigned int bi_intfreq; /* Internal Freq, in Hz */
+ unsigned int bi_busfreq; /* Bus Freq, in Hz */
+ unsigned int bi_cpmfreq; /* CPM Freq, in Hz */
+ unsigned int bi_brgfreq; /* BRG Freq, in Hz */
+ unsigned int bi_vco; /* VCO Out from PLL */
+ unsigned int bi_pci_freq; /* PCI Freq, in Hz */
+ unsigned int bi_baudrate; /* Default console baud rate */
+ unsigned int bi_immr; /* IMMR when called from boot rom */
+ unsigned char bi_enetaddr[6];
+ unsigned int bi_flashbase; /* Physical address of FLASH memory */
+ unsigned int bi_flashsize; /* Length of FLASH memory */
+ int bi_flashwidth; /* Width (8,16,32,64) */
+ unsigned char *bi_cmdline; /* Pointer to command line */
+ unsigned char bi_esa[3][6]; /* Ethernet station addresses */
+ unsigned int bi_ramdisk_begin, bi_ramdisk_end;
+ struct { /* Information about [main] video screen */
+ short x_res; /* Horizontal resolution in pixels */
+ short y_res; /* Vertical resolution in pixels */
+ short bpp; /* Bits/pixel */
+ short mode; /* Type of pixels (packed, indexed) */
+ unsigned long fb; /* Pointer to frame buffer (pixel) memory */
+ } bi_video;
+ void (*bi_cputc)(char); /* Write a character to the RedBoot console */
+ char (*bi_cgetc)(void); /* Read a character from the RedBoot console */
+ int (*bi_ctstc)(void); /* Test for input on the RedBoot console */
+} bd_t;
+
+#define BI_REV 0x0102 /* Version 1.02 */
+
+#define bi_pci_busfreq bi_pci_freq
+#define bi_immr_base bi_immr
+#endif
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index 154df05..763a0c4 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -168,7 +168,7 @@
ksection=.kernel:vmlinux.bin
isection=.kernel:initrd
;;
-ep88xc|ep405)
+ep88xc|ep405|redboot*|ep8248e)
platformo="$object/fixed-head.o $object/$platform.o"
binary=y
;;
diff --git a/arch/powerpc/configs/adder875-redboot_defconfig b/arch/powerpc/configs/adder875-redboot_defconfig
new file mode 100644
index 0000000..cab5f9b
--- /dev/null
+++ b/arch/powerpc/configs/adder875-redboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Thu Jan 17 16:17:38 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-redboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/adder875-uboot_defconfig b/arch/powerpc/configs/adder875-uboot_defconfig
new file mode 100644
index 0000000..1faf7ef
--- /dev/null
+++ b/arch/powerpc/configs/adder875-uboot_defconfig
@@ -0,0 +1,798 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Thu Jan 17 16:17:18 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_REDBOOT=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+# CONFIG_PPC_EP88XC is not set
+CONFIG_PPC_ADDER875=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_8XX_MINIMAL_FPEMU is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="adder875-uboot.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+CONFIG_FS_ENET_MDIO_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig
new file mode 100644
index 0000000..01ad595
--- /dev/null
+++ b/arch/powerpc/configs/ep8248e_defconfig
@@ -0,0 +1,821 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Fri Jan 11 14:02:06 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+# CONFIG_EXPERIMENTAL is not set
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+CONFIG_PPC_82xx=y
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_MPC8272_ADS is not set
+# CONFIG_PQ2FADS is not set
+CONFIG_EP8248E=y
+# CONFIG_PQ2ADS is not set
+CONFIG_8260=y
+CONFIG_8272=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_CPM2=y
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ep8248e.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_IP_VS is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK is not set
+# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+# CONFIG_MTD_CFI_I1 is not set
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+CONFIG_MDIO_BITBANG=y
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FCC=y
+# CONFIG_FS_ENET_MDIO_FCC is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+CONFIG_SERIAL_CPM_SCC4=y
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_JBD=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+# CONFIG_DETECT_SOFTLOCKUP is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_KGDB_CONSOLE is not set
+CONFIG_BDI_SWITCH=y
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
diff --git a/arch/powerpc/configs/mpc8313_rdb_defconfig b/arch/powerpc/configs/mpc8313_rdb_defconfig
index c9af905..db08e73 100644
--- a/arch/powerpc/configs/mpc8313_rdb_defconfig
+++ b/arch/powerpc/configs/mpc8313_rdb_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc4
-# Thu Dec 6 16:48:31 2007
+# Linux kernel version: 2.6.24-rc6
+# Thu Jan 17 16:35:55 2008
#
# CONFIG_PPC64 is not set
@@ -144,6 +144,7 @@
# CONFIG_MPC834x_MDS is not set
# CONFIG_MPC834x_ITX is not set
# CONFIG_MPC836x_MDS is not set
+# CONFIG_MPC837x_MDS is not set
CONFIG_PPC_MPC831x=y
# CONFIG_MPIC is not set
# CONFIG_MPIC_WEIRD is not set
@@ -336,15 +337,16 @@
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
-# CONFIG_MTD_PARTITIONS is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
-# CONFIG_MTD_BLKDEVS is not set
-# CONFIG_MTD_BLOCK is not set
-# CONFIG_MTD_BLOCK_RO is not set
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
@@ -381,11 +383,8 @@
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xfe000000
-CONFIG_MTD_PHYSMAP_LEN=0x1000000
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
-# CONFIG_MTD_PHYSMAP_OF is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
@@ -406,7 +405,16 @@
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_CAFE is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_ONENAND is not set
#
@@ -1178,7 +1186,17 @@
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
-# CONFIG_JFFS2_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
@@ -1242,6 +1260,8 @@
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
diff --git a/arch/powerpc/configs/mpc834x_itx_defconfig b/arch/powerpc/configs/mpc834x_itx_defconfig
index 6feb86e..2fbe4e5 100644
--- a/arch/powerpc/configs/mpc834x_itx_defconfig
+++ b/arch/powerpc/configs/mpc834x_itx_defconfig
@@ -570,7 +570,8 @@
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
-# CONFIG_PATA_PLATFORM is not set
+CONFIG_PATA_PLATFORM=y
+CONFIG_PATA_OF_PLATFORM=y
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
diff --git a/arch/powerpc/configs/mpc8610_hpcd_defconfig b/arch/powerpc/configs/mpc8610_hpcd_defconfig
index 9614d24..2500ef4 100644
--- a/arch/powerpc/configs/mpc8610_hpcd_defconfig
+++ b/arch/powerpc/configs/mpc8610_hpcd_defconfig
@@ -696,7 +696,7 @@
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
-CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
@@ -708,7 +708,60 @@
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
-# CONFIG_I2C is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
@@ -763,7 +816,119 @@
#
# Sound
#
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_PCM_OSS_PLUGINS is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+
+#
+# PCI devices
+#
+# CONFIG_SND_AD1889 is not set
+# CONFIG_SND_ALS300 is not set
+# CONFIG_SND_ALS4000 is not set
+# CONFIG_SND_ALI5451 is not set
+# CONFIG_SND_ATIIXP is not set
+# CONFIG_SND_ATIIXP_MODEM is not set
+# CONFIG_SND_AU8810 is not set
+# CONFIG_SND_AU8820 is not set
+# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AZT3328 is not set
+# CONFIG_SND_BT87X is not set
+# CONFIG_SND_CA0106 is not set
+# CONFIG_SND_CMIPCI is not set
+# CONFIG_SND_CS4281 is not set
+# CONFIG_SND_CS46XX is not set
+# CONFIG_SND_CS5530 is not set
+# CONFIG_SND_DARLA20 is not set
+# CONFIG_SND_GINA20 is not set
+# CONFIG_SND_LAYLA20 is not set
+# CONFIG_SND_DARLA24 is not set
+# CONFIG_SND_GINA24 is not set
+# CONFIG_SND_LAYLA24 is not set
+# CONFIG_SND_MONA is not set
+# CONFIG_SND_MIA is not set
+# CONFIG_SND_ECHO3G is not set
+# CONFIG_SND_INDIGO is not set
+# CONFIG_SND_INDIGOIO is not set
+# CONFIG_SND_INDIGODJ is not set
+# CONFIG_SND_EMU10K1 is not set
+# CONFIG_SND_EMU10K1X is not set
+# CONFIG_SND_ENS1370 is not set
+# CONFIG_SND_ENS1371 is not set
+# CONFIG_SND_ES1938 is not set
+# CONFIG_SND_ES1968 is not set
+# CONFIG_SND_FM801 is not set
+# CONFIG_SND_HDA_INTEL is not set
+# CONFIG_SND_HDSP is not set
+# CONFIG_SND_HDSPM is not set
+# CONFIG_SND_ICE1712 is not set
+# CONFIG_SND_ICE1724 is not set
+# CONFIG_SND_INTEL8X0 is not set
+# CONFIG_SND_INTEL8X0M is not set
+# CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_MAESTRO3 is not set
+# CONFIG_SND_MIXART is not set
+# CONFIG_SND_NM256 is not set
+# CONFIG_SND_PCXHR is not set
+# CONFIG_SND_RIPTIDE is not set
+# CONFIG_SND_RME32 is not set
+# CONFIG_SND_RME96 is not set
+# CONFIG_SND_RME9652 is not set
+# CONFIG_SND_SONICVIBES is not set
+# CONFIG_SND_TRIDENT is not set
+# CONFIG_SND_VIA82XX is not set
+# CONFIG_SND_VIA82XX_MODEM is not set
+# CONFIG_SND_VX222 is not set
+# CONFIG_SND_YMFPCI is not set
+
+#
+# ALSA PowerMac devices
+#
+
+#
+# ALSA PowerPC devices
+#
+
+#
+# System on Chip audio support
+#
+CONFIG_SND_SOC=y
+
+#
+# SoC Audio support for SuperH
+#
+
+#
+# ALSA SoC audio for Freescale SOCs
+#
+CONFIG_SND_SOC_MPC8610=y
+CONFIG_SND_SOC_MPC8610_HPCD=y
+CONFIG_SND_SOC_CS4270=y
+CONFIG_SND_SOC_CS4270_VD33_ERRATA=y
+
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
diff --git a/arch/powerpc/configs/storcenter_defconfig b/arch/powerpc/configs/storcenter_defconfig
new file mode 100644
index 0000000..a034a5e
--- /dev/null
+++ b/arch/powerpc/configs/storcenter_defconfig
@@ -0,0 +1,1174 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc6
+# Tue Jan 8 09:33:54 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+# CONFIG_ALTIVEC is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+# CONFIG_KALLSYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+
+#
+# Platform support
+#
+CONFIG_PPC_MULTIPLATFORM=y
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_86xx is not set
+CONFIG_CLASSIC32=y
+# CONFIG_PPC_CHRP is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_EFIKA is not set
+# CONFIG_PPC_LITE5200 is not set
+# CONFIG_PPC_PMAC is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_EMBEDDED6xx=y
+# CONFIG_LINKSTATION is not set
+CONFIG_STORCENTER=y
+# CONFIG_MPC7448HPC2 is not set
+# CONFIG_PPC_HOLLY is not set
+# CONFIG_PPC_PRPMC2800 is not set
+CONFIG_MPC10X_BRIDGE=y
+CONFIG_MPC10X_OPENPIC=y
+# CONFIG_MPC10X_STORE_GATHERING is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_TAU is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_HZ_100=y
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=100
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+# CONFIG_KEXEC is not set
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="console=ttyS0,115200"
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="storcenter.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=m
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_FTL=y
+CONFIG_NFTL=y
+CONFIG_NFTL_RW=y
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0xFF800000
+CONFIG_MTD_PHYSMAP_LEN=0x00800000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=1
+# CONFIG_MTD_PHYSMAP_OF is not set
+# CONFIG_MTD_INTEL_VR_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+CONFIG_IDE=y
+CONFIG_IDE_MAX_HWIFS=4
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+CONFIG_IDEDISK_MULTI_MODE=y
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_BLK_DEV_IDESCSI is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
+CONFIG_BLK_DEV_IDEPCI=y
+# CONFIG_IDEPCI_SHARE_IRQ is not set
+CONFIG_IDEPCI_PCIBUS_ORDER=y
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_BLK_DEV_OPTI621 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_BLK_DEV_TC86C001 is not set
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+CONFIG_IDE_ARCH_OBSOLETE_INIT=y
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+CONFIG_BLK_DEV_SR=y
+# CONFIG_BLK_DEV_SR_VENDOR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+CONFIG_SCSI_SPI_ATTRS=y
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ADVANSYS is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
+# CONFIG_ATA is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_MD_LINEAR=y
+CONFIG_MD_RAID0=y
+CONFIG_MD_RAID1=y
+# CONFIG_MD_RAID10 is not set
+CONFIG_MD_RAID456=y
+CONFIG_MD_RAID5_RESHAPE=y
+# CONFIG_MD_MULTIPATH is not set
+# CONFIG_MD_FAULTY is not set
+# CONFIG_BLK_DEV_DM is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_DUMMY=m
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_IP1000 is not set
+# CONFIG_ARCNET is not set
+# CONFIG_NET_ETHERNET is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+CONFIG_R8169=y
+# CONFIG_R8169_NAPI is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_MV643XX_ETH is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=m
+CONFIG_NVRAM=y
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_SPLIT_ISO is not set
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+# CONFIG_USB_MON is not set
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+CONFIG_RTC_DRV_DS1307=y
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+CONFIG_XFS_FS=m
+# CONFIG_XFS_QUOTA is not set
+# CONFIG_XFS_SECURITY is not set
+# CONFIG_XFS_POSIX_ACL is not set
+# CONFIG_XFS_RT is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NETWORK_FILESYSTEMS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_XOR_BLOCKS=y
+CONFIG_ASYNC_CORE=y
+CONFIG_ASYNC_MEMCPY=y
+CONFIG_ASYNC_XOR=y
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile
index d9b3770..58dbfef 100644
--- a/arch/powerpc/kernel/Makefile
+++ b/arch/powerpc/kernel/Makefile
@@ -70,6 +70,7 @@
obj-$(CONFIG_PCI) += pci_$(CONFIG_WORD_SIZE).o $(pci64-y) \
pci-common.o
obj-$(CONFIG_PCI_MSI) += msi.o
+obj-$(CONFIG_RAPIDIO) += rio.o
obj-$(CONFIG_KEXEC) += machine_kexec.o crash.o \
machine_kexec_$(CONFIG_WORD_SIZE).o
obj-$(CONFIG_AUDIT) += audit.o
diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S
index 7aecb39..d9cc2c2 100644
--- a/arch/powerpc/kernel/head_fsl_booke.S
+++ b/arch/powerpc/kernel/head_fsl_booke.S
@@ -73,8 +73,8 @@
/* We try to not make any assumptions about how the boot loader
* setup or used the TLBs. We invalidate all mappings from the
* boot loader and load a single entry in TLB1[0] to map the
- * first 16M of kernel memory. Any boot info passed from the
- * bootloader needs to live in this first 16M.
+ * first 64M of kernel memory. Any boot info passed from the
+ * bootloader needs to live in this first 64M.
*
* Requirement on bootloader:
* - The page we're executing in needs to reside in TLB1 and
@@ -167,7 +167,7 @@
mtspr SPRN_MAS0,r7
tlbre
- /* Just modify the entry ID and EPN for the temp mapping */
+ /* Just modify the entry ID, EPN and RPN for the temp mapping */
lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r5,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r5) */
mtspr SPRN_MAS0,r7
@@ -177,9 +177,12 @@
ori r6,r6,(MAS1_TSIZE(BOOKE_PAGESZ_4K))@l
mtspr SPRN_MAS1,r6
mfspr r6,SPRN_MAS2
- li r7,0 /* temp EPN = 0 */
+ lis r7,PHYSICAL_START@h
rlwimi r7,r6,0,20,31
mtspr SPRN_MAS2,r7
+ mfspr r6,SPRN_MAS3
+ rlwimi r7,r6,0,20,31
+ mtspr SPRN_MAS3,r7
tlbwe
xori r6,r4,1
@@ -222,11 +225,11 @@
lis r6,0x1000 /* Set MAS0(TLBSEL) = TLB1(1), ESEL = 0 */
mtspr SPRN_MAS0,r6
lis r6,(MAS1_VALID|MAS1_IPROT)@h
- ori r6,r6,(MAS1_TSIZE(BOOKE_PAGESZ_16M))@l
+ ori r6,r6,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l
mtspr SPRN_MAS1,r6
li r7,0
- lis r6,KERNELBASE@h
- ori r6,r6,KERNELBASE@l
+ lis r6,PAGE_OFFSET@h
+ ori r6,r6,PAGE_OFFSET@l
rlwimi r6,r7,0,20,31
mtspr SPRN_MAS2,r6
li r7,(MAS3_SX|MAS3_SW|MAS3_SR)
@@ -234,6 +237,9 @@
tlbwe
/* 7. Jump to KERNELBASE mapping */
+ lis r6,KERNELBASE@h
+ ori r6,r6,KERNELBASE@l
+ rlwimi r6,r7,0,20,31
lis r7,MSR_KERNEL@h
ori r7,r7,MSR_KERNEL@l
bl 1f /* Find our address */
diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c
index d394d41..980fe32 100644
--- a/arch/powerpc/kernel/pci-common.c
+++ b/arch/powerpc/kernel/pci-common.c
@@ -792,9 +792,10 @@
for (i = 0; i < PCI_BUS_NUM_RESOURCES; ++i) {
if ((res = bus->resource[i]) == NULL)
continue;
- if (!res->flags || bus->self->transparent)
+ if (!res->flags)
continue;
-
+ if (i >= 3 && bus->self->transparent)
+ continue;
/* On PowerMac, Apple leaves bridge windows open over
* an inaccessible region of memory space (0...fffff)
* which is somewhat bogus, but that's what they think
@@ -806,7 +807,8 @@
* equal to the pci_mem_offset of the host bridge and
* their size is smaller than 1M.
*/
- if (res->start == hose->pci_mem_offset &&
+ if (res->flags & IORESOURCE_MEM &&
+ res->start == hose->pci_mem_offset &&
res->end < 0x100000) {
printk(KERN_INFO
"PCI: Closing bogus Apple Firmware"
diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c
index 14e300f..88db4ff 100644
--- a/arch/powerpc/kernel/pci_32.c
+++ b/arch/powerpc/kernel/pci_32.c
@@ -94,64 +94,6 @@
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CPC710_PCI64, fixup_cpc710_pci64);
-
-void __init
-update_bridge_resource(struct pci_dev *dev, struct resource *res)
-{
- u8 io_base_lo, io_limit_lo;
- u16 mem_base, mem_limit;
- u16 cmd;
- resource_size_t start, end, off;
- struct pci_controller *hose = dev->sysdata;
-
- if (!hose) {
- printk("update_bridge_base: no hose?\n");
- return;
- }
- pci_read_config_word(dev, PCI_COMMAND, &cmd);
- pci_write_config_word(dev, PCI_COMMAND,
- cmd & ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY));
- if (res->flags & IORESOURCE_IO) {
- off = (unsigned long) hose->io_base_virt - isa_io_base;
- start = res->start - off;
- end = res->end - off;
- io_base_lo = (start >> 8) & PCI_IO_RANGE_MASK;
- io_limit_lo = (end >> 8) & PCI_IO_RANGE_MASK;
- if (end > 0xffff)
- io_base_lo |= PCI_IO_RANGE_TYPE_32;
- else
- io_base_lo |= PCI_IO_RANGE_TYPE_16;
- pci_write_config_word(dev, PCI_IO_BASE_UPPER16,
- start >> 16);
- pci_write_config_word(dev, PCI_IO_LIMIT_UPPER16,
- end >> 16);
- pci_write_config_byte(dev, PCI_IO_BASE, io_base_lo);
- pci_write_config_byte(dev, PCI_IO_LIMIT, io_limit_lo);
-
- } else if ((res->flags & (IORESOURCE_MEM | IORESOURCE_PREFETCH))
- == IORESOURCE_MEM) {
- off = hose->pci_mem_offset;
- mem_base = ((res->start - off) >> 16) & PCI_MEMORY_RANGE_MASK;
- mem_limit = ((res->end - off) >> 16) & PCI_MEMORY_RANGE_MASK;
- pci_write_config_word(dev, PCI_MEMORY_BASE, mem_base);
- pci_write_config_word(dev, PCI_MEMORY_LIMIT, mem_limit);
-
- } else if ((res->flags & (IORESOURCE_MEM | IORESOURCE_PREFETCH))
- == (IORESOURCE_MEM | IORESOURCE_PREFETCH)) {
- off = hose->pci_mem_offset;
- mem_base = ((res->start - off) >> 16) & PCI_PREF_RANGE_MASK;
- mem_limit = ((res->end - off) >> 16) & PCI_PREF_RANGE_MASK;
- pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, mem_base);
- pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, mem_limit);
-
- } else {
- DBG(KERN_ERR "PCI: ugh, bridge %s res has flags=%lx\n",
- pci_name(dev), res->flags);
- }
- pci_write_config_word(dev, PCI_COMMAND, cmd);
-}
-
-
#ifdef CONFIG_PPC_OF
/*
* Functions below are used on OpenFirmware machines.
diff --git a/arch/ppc/kernel/rio.c b/arch/powerpc/kernel/rio.c
similarity index 100%
rename from arch/ppc/kernel/rio.c
rename to arch/powerpc/kernel/rio.c
diff --git a/arch/powerpc/math-emu/op-4.h b/arch/powerpc/math-emu/op-4.h
index fcdd6d0..c9ae626 100644
--- a/arch/powerpc/math-emu/op-4.h
+++ b/arch/powerpc/math-emu/op-4.h
@@ -194,19 +194,39 @@
(X##_f[3] = I3, X##_f[2] = I2, X##_f[1] = I1, X##_f[0] = I0)
#ifndef __FP_FRAC_ADD_4
-#define __FP_FRAC_ADD_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \
- (r0 = x0 + y0, \
- r1 = x1 + y1 + (r0 < x0), \
- r2 = x2 + y2 + (r1 < x1), \
- r3 = x3 + y3 + (r2 < x2))
+#define __FP_FRAC_ADD_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \
+ do { \
+ int _c1, _c2, _c3; \
+ r0 = x0 + y0; \
+ _c1 = r0 < x0; \
+ r1 = x1 + y1; \
+ _c2 = r1 < x1; \
+ r1 += _c1; \
+ _c2 |= r1 < _c1; \
+ r2 = x2 + y2; \
+ _c3 = r2 < x2; \
+ r2 += _c2; \
+ _c3 |= r2 < _c2; \
+ r3 = x3 + y3 + _c3; \
+ } while (0)
#endif
#ifndef __FP_FRAC_SUB_4
-#define __FP_FRAC_SUB_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \
- (r0 = x0 - y0, \
- r1 = x1 - y1 - (r0 > x0), \
- r2 = x2 - y2 - (r1 > x1), \
- r3 = x3 - y3 - (r2 > x2))
+#define __FP_FRAC_SUB_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \
+ do { \
+ int _c1, _c2, _c3; \
+ r0 = x0 - y0; \
+ _c1 = r0 > x0; \
+ r1 = x1 - y1; \
+ _c2 = r1 > x1; \
+ r1 -= _c1; \
+ _c2 |= r1 > _c1; \
+ r2 = x2 - y2; \
+ _c3 = r2 > x2; \
+ r2 -= _c2; \
+ _c3 |= r2 > _c2; \
+ r3 = x3 - y3 - _c3; \
+ } while (0)
#endif
#ifndef __FP_FRAC_ADDI_4
diff --git a/arch/powerpc/mm/fsl_booke_mmu.c b/arch/powerpc/mm/fsl_booke_mmu.c
index 17139da..c93a966 100644
--- a/arch/powerpc/mm/fsl_booke_mmu.c
+++ b/arch/powerpc/mm/fsl_booke_mmu.c
@@ -165,15 +165,15 @@
void __init cam_mapin_ram(unsigned long cam0, unsigned long cam1,
unsigned long cam2)
{
- settlbcam(0, KERNELBASE, PPC_MEMSTART, cam0, _PAGE_KERNEL, 0);
+ settlbcam(0, PAGE_OFFSET, PPC_MEMSTART, cam0, _PAGE_KERNEL, 0);
tlbcam_index++;
if (cam1) {
tlbcam_index++;
- settlbcam(1, KERNELBASE+cam0, PPC_MEMSTART+cam0, cam1, _PAGE_KERNEL, 0);
+ settlbcam(1, PAGE_OFFSET+cam0, PPC_MEMSTART+cam0, cam1, _PAGE_KERNEL, 0);
}
if (cam2) {
tlbcam_index++;
- settlbcam(2, KERNELBASE+cam0+cam1, PPC_MEMSTART+cam0+cam1, cam2, _PAGE_KERNEL, 0);
+ settlbcam(2, PAGE_OFFSET+cam0+cam1, PPC_MEMSTART+cam0+cam1, cam2, _PAGE_KERNEL, 0);
}
}
diff --git a/arch/powerpc/mm/lmb.c b/arch/powerpc/mm/lmb.c
index 8f4d2dc..4ce23bc 100644
--- a/arch/powerpc/mm/lmb.c
+++ b/arch/powerpc/mm/lmb.c
@@ -342,3 +342,16 @@
}
}
}
+
+int __init lmb_is_reserved(unsigned long addr)
+{
+ int i;
+
+ for (i = 0; i < lmb.reserved.cnt; i++) {
+ unsigned long upper = lmb.reserved.region[i].base +
+ lmb.reserved.region[i].size - 1;
+ if ((addr >= lmb.reserved.region[i].base) && (addr <= upper))
+ return 1;
+ }
+ return 0;
+}
diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c
index 5402fb6b..e812244 100644
--- a/arch/powerpc/mm/mem.c
+++ b/arch/powerpc/mm/mem.c
@@ -213,15 +213,30 @@
*/
#ifdef CONFIG_HIGHMEM
free_bootmem_with_active_regions(0, total_lowmem >> PAGE_SHIFT);
+
+ /* reserve the sections we're already using */
+ for (i = 0; i < lmb.reserved.cnt; i++) {
+ unsigned long addr = lmb.reserved.region[i].base +
+ lmb_size_bytes(&lmb.reserved, i) - 1;
+ if (addr < total_lowmem)
+ reserve_bootmem(lmb.reserved.region[i].base,
+ lmb_size_bytes(&lmb.reserved, i));
+ else if (lmb.reserved.region[i].base < total_lowmem) {
+ unsigned long adjusted_size = total_lowmem -
+ lmb.reserved.region[i].base;
+ reserve_bootmem(lmb.reserved.region[i].base,
+ adjusted_size);
+ }
+ }
#else
free_bootmem_with_active_regions(0, max_pfn);
-#endif
/* reserve the sections we're already using */
for (i = 0; i < lmb.reserved.cnt; i++)
reserve_bootmem(lmb.reserved.region[i].base,
lmb_size_bytes(&lmb.reserved, i));
+#endif
/* XXX need to clip this if using highmem? */
sparse_memory_present_with_active_regions(0);
@@ -334,11 +349,13 @@
highmem_mapnr = total_lowmem >> PAGE_SHIFT;
for (pfn = highmem_mapnr; pfn < max_mapnr; ++pfn) {
struct page *page = pfn_to_page(pfn);
-
+ if (lmb_is_reserved(pfn << PAGE_SHIFT))
+ continue;
ClearPageReserved(page);
init_page_count(page);
__free_page(page);
totalhigh_pages++;
+ reservedpages--;
}
totalram_pages += totalhigh_pages;
printk(KERN_DEBUG "High memory: %luk\n",
diff --git a/arch/powerpc/platforms/82xx/Kconfig b/arch/powerpc/platforms/82xx/Kconfig
index 541fbb8..4fad6c7 100644
--- a/arch/powerpc/platforms/82xx/Kconfig
+++ b/arch/powerpc/platforms/82xx/Kconfig
@@ -26,6 +26,19 @@
help
This option enables support for the PQ2FADS board
+config EP8248E
+ bool "Embedded Planet EP8248E (a.k.a. CWH-PPC-8248N-VE)"
+ select 8272
+ select 8260
+ select FSL_SOC
+ select PPC_CPM_NEW_BINDING
+ select MDIO_BITBANG
+ help
+ This enables support for the Embedded Planet EP8248E board.
+
+ This board is also resold by Freescale as the QUICCStart
+ MPC8248 Evaluation System and/or the CWH-PPC-8248N-VE.
+
endchoice
config PQ2ADS
diff --git a/arch/powerpc/platforms/82xx/Makefile b/arch/powerpc/platforms/82xx/Makefile
index 68c8b0c..6cd5cd5 100644
--- a/arch/powerpc/platforms/82xx/Makefile
+++ b/arch/powerpc/platforms/82xx/Makefile
@@ -5,3 +5,4 @@
obj-$(CONFIG_CPM2) += pq2.o
obj-$(CONFIG_PQ2_ADS_PCI_PIC) += pq2ads-pci-pic.o
obj-$(CONFIG_PQ2FADS) += pq2fads.o
+obj-$(CONFIG_EP8248E) += ep8248e.o
diff --git a/arch/powerpc/platforms/82xx/ep8248e.c b/arch/powerpc/platforms/82xx/ep8248e.c
new file mode 100644
index 0000000..ba93d8a
--- /dev/null
+++ b/arch/powerpc/platforms/82xx/ep8248e.c
@@ -0,0 +1,324 @@
+/*
+ * Embedded Planet EP8248E support
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/fsl_devices.h>
+#include <linux/mdio-bitbang.h>
+#include <linux/of_platform.h>
+
+#include <asm/io.h>
+#include <asm/cpm2.h>
+#include <asm/udbg.h>
+#include <asm/machdep.h>
+#include <asm/time.h>
+#include <asm/mpc8260.h>
+#include <asm/prom.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/cpm2_pic.h>
+
+#include "pq2.h"
+
+static u8 __iomem *ep8248e_bcsr;
+static struct device_node *ep8248e_bcsr_node;
+
+#define BCSR7_SCC2_ENABLE 0x10
+
+#define BCSR8_PHY1_ENABLE 0x80
+#define BCSR8_PHY1_POWER 0x40
+#define BCSR8_PHY2_ENABLE 0x20
+#define BCSR8_PHY2_POWER 0x10
+#define BCSR8_MDIO_READ 0x04
+#define BCSR8_MDIO_CLOCK 0x02
+#define BCSR8_MDIO_DATA 0x01
+
+#define BCSR9_USB_ENABLE 0x80
+#define BCSR9_USB_POWER 0x40
+#define BCSR9_USB_HOST 0x20
+#define BCSR9_USB_FULL_SPEED_TARGET 0x10
+
+static void __init ep8248e_pic_init(void)
+{
+ struct device_node *np = of_find_compatible_node(NULL, NULL, "fsl,pq2-pic");
+ if (!np) {
+ printk(KERN_ERR "PIC init: can not find cpm-pic node\n");
+ return;
+ }
+
+ cpm2_pic_init(np);
+ of_node_put(np);
+}
+
+static void ep8248e_set_mdc(struct mdiobb_ctrl *ctrl, int level)
+{
+ if (level)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_CLOCK);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_dir(struct mdiobb_ctrl *ctrl, int output)
+{
+ if (output)
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+ else
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_READ);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static void ep8248e_set_mdio_data(struct mdiobb_ctrl *ctrl, int data)
+{
+ if (data)
+ setbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+ else
+ clrbits8(&ep8248e_bcsr[8], BCSR8_MDIO_DATA);
+
+ /* Read back to flush the write. */
+ in_8(&ep8248e_bcsr[8]);
+}
+
+static int ep8248e_get_mdio_data(struct mdiobb_ctrl *ctrl)
+{
+ return in_8(&ep8248e_bcsr[8]) & BCSR8_MDIO_DATA;
+}
+
+static const struct mdiobb_ops ep8248e_mdio_ops = {
+ .set_mdc = ep8248e_set_mdc,
+ .set_mdio_dir = ep8248e_set_mdio_dir,
+ .set_mdio_data = ep8248e_set_mdio_data,
+ .get_mdio_data = ep8248e_get_mdio_data,
+ .owner = THIS_MODULE,
+};
+
+static struct mdiobb_ctrl ep8248e_mdio_ctrl = {
+ .ops = &ep8248e_mdio_ops,
+};
+
+static int __devinit ep8248e_mdio_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct mii_bus *bus;
+ struct resource res;
+ struct device_node *node;
+ int ret, i;
+
+ node = of_get_parent(ofdev->node);
+ of_node_put(node);
+ if (node != ep8248e_bcsr_node)
+ return -ENODEV;
+
+ ret = of_address_to_resource(ofdev->node, 0, &res);
+ if (ret)
+ return ret;
+
+ bus = alloc_mdio_bitbang(&ep8248e_mdio_ctrl);
+ if (!bus)
+ return -ENOMEM;
+
+ bus->phy_mask = 0;
+ bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++)
+ bus->irq[i] = -1;
+
+ bus->name = "ep8248e-mdio-bitbang";
+ bus->dev = &ofdev->dev;
+ bus->id = res.start;
+
+ return mdiobus_register(bus);
+}
+
+static int ep8248e_mdio_remove(struct of_device *ofdev)
+{
+ BUG();
+ return 0;
+}
+
+static const struct of_device_id ep8248e_mdio_match[] = {
+ {
+ .compatible = "fsl,ep8248e-mdio-bitbang",
+ },
+ {},
+};
+
+static struct of_platform_driver ep8248e_mdio_driver = {
+ .driver = {
+ .name = "ep8248e-mdio-bitbang",
+ },
+ .match_table = ep8248e_mdio_match,
+ .probe = ep8248e_mdio_probe,
+ .remove = ep8248e_mdio_remove,
+};
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static __initdata struct cpm_pin ep8248e_pins[] = {
+ /* SMC1 */
+ {2, 4, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+
+ /* SCC1 */
+ {2, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC1 */
+ {0, 14, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 15, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {0, 18, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 19, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {0, 26, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 27, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 28, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {0, 30, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {0, 31, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {2, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* FCC2 */
+ {1, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 20, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 22, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 25, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {1, 26, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 27, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {1, 30, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+ /* I2C */
+ {4, 14, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+ {4, 15, CPM_PIN_INPUT | CPM_PIN_SECONDARY},
+
+ /* USB */
+ {2, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {2, 24, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {3, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+ {3, 25, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ep8248e_pins); i++) {
+ const struct cpm_pin *pin = &ep8248e_pins[i];
+ cpm2_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm2_smc_clk_setup(CPM_CLK_SMC1, CPM_BRG7);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_SCC3, CPM_CLK8, CPM_CLK_TX); /* USB */
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK11, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK10, CPM_CLK_TX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK13, CPM_CLK_RX);
+ cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK14, CPM_CLK_TX);
+}
+
+static void __init ep8248e_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248e_setup_arch()", 0);
+
+ cpm2_reset();
+
+ /* When this is set, snooping CPM DMA from RAM causes
+ * machine checks. See erratum SIU18.
+ */
+ clrbits32(&cpm2_immr->im_siu_conf.siu_82xx.sc_bcr, MPC82XX_BCR_PLDP);
+
+ ep8248e_bcsr_node =
+ of_find_compatible_node(NULL, NULL, "fsl,ep8248e-bcsr");
+ if (!ep8248e_bcsr_node) {
+ printk(KERN_ERR "No bcsr in device tree\n");
+ return;
+ }
+
+ ep8248e_bcsr = of_iomap(ep8248e_bcsr_node, 0);
+ if (!ep8248e_bcsr) {
+ printk(KERN_ERR "Cannot map BCSR registers\n");
+ of_node_put(ep8248e_bcsr_node);
+ ep8248e_bcsr_node = NULL;
+ return;
+ }
+
+ setbits8(&ep8248e_bcsr[7], BCSR7_SCC2_ENABLE);
+ setbits8(&ep8248e_bcsr[8], BCSR8_PHY1_ENABLE | BCSR8_PHY1_POWER |
+ BCSR8_PHY2_ENABLE | BCSR8_PHY2_POWER);
+
+ init_ioports();
+
+ if (ppc_md.progress)
+ ppc_md.progress("ep8248e_setup_arch(), finish", 0);
+}
+
+static __initdata struct of_device_id of_bus_ids[] = {
+ { .compatible = "simple-bus", },
+ { .compatible = "fsl,ep8248e-bcsr", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_register_platform_driver(&ep8248e_mdio_driver);
+
+ return 0;
+}
+machine_device_initcall(ep8248e, declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ep8248e_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "fsl,ep8248e");
+}
+
+define_machine(ep8248e)
+{
+ .name = "Embedded Planet EP8248E",
+ .probe = ep8248e_probe,
+ .setup_arch = ep8248e_setup_arch,
+ .init_IRQ = ep8248e_pic_init,
+ .get_irq = cpm2_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .restart = pq2_restart,
+ .progress = udbg_progress,
+};
diff --git a/arch/powerpc/platforms/83xx/mpc8313_rdb.c b/arch/powerpc/platforms/83xx/mpc8313_rdb.c
index 6fb8299..4996b7d 100644
--- a/arch/powerpc/platforms/83xx/mpc8313_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc8313_rdb.c
@@ -14,6 +14,7 @@
*/
#include <linux/pci.h>
+#include <linux/of_platform.h>
#include <asm/time.h>
#include <asm/ipic.h>
@@ -75,6 +76,18 @@
return of_flat_dt_is_compatible(root, "MPC8313ERDB");
}
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .compatible = "simple-bus" },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ return 0;
+}
+machine_device_initcall(mpc8313_rdb, declare_of_platform_devices);
+
define_machine(mpc8313_rdb) {
.name = "MPC8313 RDB",
.probe = mpc8313_rdb_probe,
diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c
index 1e570bb..dbdd4ad 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
@@ -110,15 +110,12 @@
static int __init mpc832x_declare_of_platform_devices(void)
{
- if (!machine_is(mpc832x_mds))
- return 0;
-
/* Publish the QE devices */
of_platform_bus_probe(NULL, mpc832x_ids, NULL);
return 0;
}
-device_initcall(mpc832x_declare_of_platform_devices);
+machine_device_initcall(mpc832x_mds, mpc832x_declare_of_platform_devices);
static void __init mpc832x_sys_init_IRQ(void)
{
diff --git a/arch/powerpc/platforms/83xx/mpc832x_rdb.c b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
index ffb2e93..5fddd22 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
@@ -63,9 +63,6 @@
static int __init mpc832x_spi_init(void)
{
- if (!machine_is(mpc832x_rdb))
- return 0;
-
par_io_config_pin(3, 0, 3, 0, 1, 0); /* SPI1 MOSI, I/O */
par_io_config_pin(3, 1, 3, 0, 1, 0); /* SPI1 MISO, I/O */
par_io_config_pin(3, 2, 3, 0, 1, 0); /* SPI1 CLK, I/O */
@@ -80,7 +77,7 @@
mpc83xx_spi_deactivate_cs);
}
-device_initcall(mpc832x_spi_init);
+machine_device_initcall(mpc832x_rdb, mpc832x_spi_init);
/* ************************************************************************
*
@@ -123,15 +120,12 @@
static int __init mpc832x_declare_of_platform_devices(void)
{
- if (!machine_is(mpc832x_rdb))
- return 0;
-
/* Publish the QE devices */
of_platform_bus_probe(NULL, mpc832x_ids, NULL);
return 0;
}
-device_initcall(mpc832x_declare_of_platform_devices);
+machine_device_initcall(mpc832x_rdb, mpc832x_declare_of_platform_devices);
void __init mpc832x_rdb_init_IRQ(void)
{
diff --git a/arch/powerpc/platforms/83xx/mpc834x_itx.c b/arch/powerpc/platforms/83xx/mpc834x_itx.c
index aa76819..50e8f63 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_itx.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_itx.c
@@ -23,6 +23,7 @@
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/root_dev.h>
+#include <linux/of_platform.h>
#include <asm/system.h>
#include <asm/atomic.h>
@@ -37,6 +38,17 @@
#include "mpc83xx.h"
+static struct of_device_id __initdata mpc834x_itx_ids[] = {
+ { .compatible = "fsl,pq2pro-localbus", },
+ {},
+};
+
+static int __init mpc834x_itx_declare_of_platform_devices(void)
+{
+ return of_platform_bus_probe(NULL, mpc834x_itx_ids, NULL);
+}
+machine_device_initcall(mpc834x_itx, mpc834x_itx_declare_of_platform_devices);
+
/* ************************************************************************
*
* Setup the architecture
diff --git a/arch/powerpc/platforms/83xx/mpc834x_mds.c b/arch/powerpc/platforms/83xx/mpc834x_mds.c
index 459fb72..2b8a0a3 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_mds.c
@@ -115,13 +115,10 @@
static int __init mpc834x_declare_of_platform_devices(void)
{
- if (!machine_is(mpc834x_mds))
- return 0;
-
of_platform_bus_probe(NULL, mpc834x_ids, NULL);
return 0;
}
-device_initcall(mpc834x_declare_of_platform_devices);
+machine_device_initcall(mpc834x_mds, mpc834x_declare_of_platform_devices);
/*
* Called very early, MMU is off, device-tree isn't unflattened
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 2ac9890..db491ec 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -141,15 +141,12 @@
static int __init mpc836x_declare_of_platform_devices(void)
{
- if (!machine_is(mpc836x_mds))
- return 0;
-
/* Publish the QE devices */
of_platform_bus_probe(NULL, mpc836x_ids, NULL);
return 0;
}
-device_initcall(mpc836x_declare_of_platform_devices);
+machine_device_initcall(mpc836x_mds, mpc836x_declare_of_platform_devices);
static void __init mpc836x_mds_init_IRQ(void)
{
diff --git a/arch/powerpc/platforms/83xx/mpc837x_mds.c b/arch/powerpc/platforms/83xx/mpc837x_mds.c
index 9cdc32b..8a9c269 100644
--- a/arch/powerpc/platforms/83xx/mpc837x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc837x_mds.c
@@ -22,6 +22,56 @@
#include "mpc83xx.h"
+#define BCSR12_USB_SER_MASK 0x8a
+#define BCSR12_USB_SER_PIN 0x80
+#define BCSR12_USB_SER_DEVICE 0x02
+extern int mpc837x_usb_cfg(void);
+
+static int mpc837xmds_usb_cfg(void)
+{
+ struct device_node *np;
+ const void *phy_type, *mode;
+ void __iomem *bcsr_regs = NULL;
+ u8 bcsr12;
+ int ret;
+
+ ret = mpc837x_usb_cfg();
+ if (ret)
+ return ret;
+ /* Map BCSR area */
+ np = of_find_node_by_name(NULL, "bcsr");
+ if (np) {
+ struct resource res;
+
+ of_address_to_resource(np, 0, &res);
+ bcsr_regs = ioremap(res.start, res.end - res.start + 1);
+ of_node_put(np);
+ }
+ if (!bcsr_regs)
+ return -1;
+
+ np = of_find_node_by_name(NULL, "usb");
+ if (!np)
+ return -ENODEV;
+ phy_type = of_get_property(np, "phy_type", NULL);
+ if (phy_type && !strcmp(phy_type, "ulpi")) {
+ clrbits8(bcsr_regs + 12, BCSR12_USB_SER_PIN);
+ } else if (phy_type && !strcmp(phy_type, "serial")) {
+ mode = of_get_property(np, "dr_mode", NULL);
+ bcsr12 = in_8(bcsr_regs + 12) & ~BCSR12_USB_SER_MASK;
+ bcsr12 |= BCSR12_USB_SER_PIN;
+ if (mode && !strcmp(mode, "peripheral"))
+ bcsr12 |= BCSR12_USB_SER_DEVICE;
+ out_8(bcsr_regs + 12, bcsr12);
+ } else {
+ printk(KERN_ERR "USB DR: unsupported PHY\n");
+ }
+
+ of_node_put(np);
+ iounmap(bcsr_regs);
+ return 0;
+}
+
/* ************************************************************************
*
* Setup the architecture
@@ -40,6 +90,7 @@
for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
mpc83xx_add_bridge(np);
#endif
+ mpc837xmds_usb_cfg();
}
static struct of_device_id mpc837x_ids[] = {
@@ -50,15 +101,12 @@
static int __init mpc837x_declare_of_platform_devices(void)
{
- if (!machine_is(mpc837x_mds))
- return 0;
-
/* Publish of_device */
of_platform_bus_probe(NULL, mpc837x_ids, NULL);
return 0;
}
-device_initcall(mpc837x_declare_of_platform_devices);
+machine_device_initcall(mpc837x_mds, mpc837x_declare_of_platform_devices);
static void __init mpc837x_mds_init_IRQ(void)
{
diff --git a/arch/powerpc/platforms/83xx/mpc83xx.h b/arch/powerpc/platforms/83xx/mpc83xx.h
index b778cb4..88bb748 100644
--- a/arch/powerpc/platforms/83xx/mpc83xx.h
+++ b/arch/powerpc/platforms/83xx/mpc83xx.h
@@ -14,6 +14,7 @@
#define MPC83XX_SCCR_USB_DRCM_11 0x00300000
#define MPC83XX_SCCR_USB_DRCM_01 0x00100000
#define MPC83XX_SCCR_USB_DRCM_10 0x00200000
+#define MPC837X_SCCR_USB_DRCM_11 0x00c00000
/* system i/o configuration register low */
#define MPC83XX_SICRL_OFFS 0x114
@@ -22,6 +23,8 @@
#define MPC834X_SICRL_USB1 0x20000000
#define MPC831X_SICRL_USB_MASK 0x00000c00
#define MPC831X_SICRL_USB_ULPI 0x00000800
+#define MPC837X_SICRL_USB_MASK 0xf0000000
+#define MPC837X_SICRL_USB_ULPI 0x50000000
/* system i/o configuration register high */
#define MPC83XX_SICRH_OFFS 0x118
diff --git a/arch/powerpc/platforms/83xx/usb.c b/arch/powerpc/platforms/83xx/usb.c
index b45160f..6a454a4 100644
--- a/arch/powerpc/platforms/83xx/usb.c
+++ b/arch/powerpc/platforms/83xx/usb.c
@@ -41,7 +41,7 @@
sicrl = in_be32(immap + MPC83XX_SICRL_OFFS) & ~MPC834X_SICRL_USB_MASK;
sicrh = in_be32(immap + MPC83XX_SICRH_OFFS) & ~MPC834X_SICRH_USB_UTMI;
- np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr");
+ np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
if (np) {
sccr |= MPC83XX_SCCR_USB_DRCM_11; /* 1:3 */
@@ -67,7 +67,7 @@
port0_is_dr = 1;
of_node_put(np);
}
- np = of_find_compatible_node(NULL, "usb", "fsl-usb2-mph");
+ np = of_find_compatible_node(NULL, NULL, "fsl-usb2-mph");
if (np) {
sccr |= MPC83XX_SCCR_USB_MPHCM_11; /* 1:3 */
@@ -111,7 +111,7 @@
const void *dr_mode;
#endif
- np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr");
+ np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
if (!np)
return -ENODEV;
prop = of_get_property(np, "phy_type", NULL);
@@ -179,3 +179,43 @@
return ret;
}
#endif /* CONFIG_PPC_MPC831x */
+
+#ifdef CONFIG_PPC_MPC837x
+int mpc837x_usb_cfg(void)
+{
+ void __iomem *immap;
+ struct device_node *np = NULL;
+ const void *prop;
+ int ret = 0;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
+ if (!np)
+ return -ENODEV;
+ prop = of_get_property(np, "phy_type", NULL);
+
+ if (!prop || (strcmp(prop, "ulpi") && strcmp(prop, "serial"))) {
+ printk(KERN_WARNING "837x USB PHY type not supported\n");
+ of_node_put(np);
+ return -EINVAL;
+ }
+
+ /* Map IMMR space for pin and clock settings */
+ immap = ioremap(get_immrbase(), 0x1000);
+ if (!immap) {
+ of_node_put(np);
+ return -ENOMEM;
+ }
+
+ /* Configure clock */
+ clrsetbits_be32(immap + MPC83XX_SCCR_OFFS, MPC837X_SCCR_USB_DRCM_11,
+ MPC837X_SCCR_USB_DRCM_11);
+
+ /* Configure pin mux for ULPI/serial */
+ clrsetbits_be32(immap + MPC83XX_SICRL_OFFS, MPC837X_SICRL_USB_MASK,
+ MPC837X_SICRL_USB_ULPI);
+
+ iounmap(immap);
+ of_node_put(np);
+ return ret;
+}
+#endif /* CONFIG_PPC_MPC837x */
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
index bccdc25..4e03050 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
@@ -52,9 +52,9 @@
{
int cascade_irq;
- while ((cascade_irq = cpm2_get_irq()) >= 0) {
+ while ((cascade_irq = cpm2_get_irq()) >= 0)
generic_handle_irq(cascade_irq);
- }
+
desc->chip->eoi(irq);
}
@@ -70,13 +70,12 @@
#endif
np = of_find_node_by_type(np, "open-pic");
-
- if (np == NULL) {
+ if (!np) {
printk(KERN_ERR "Could not find open-pic node\n");
return;
}
- if(of_address_to_resource(np, 0, &r)) {
+ if (of_address_to_resource(np, 0, &r)) {
printk(KERN_ERR "Could not map mpic register space\n");
of_node_put(np);
return;
@@ -100,6 +99,7 @@
irq = irq_of_parse_and_map(np, 0);
cpm2_pic_init(np);
+ of_node_put(np);
set_irq_chained_handler(irq, cpm2_cascade);
#endif
}
@@ -112,7 +112,7 @@
int port, pin, flags;
};
-static struct cpm_pin mpc8560_ads_pins[] = {
+static const struct cpm_pin mpc8560_ads_pins[] = {
/* SCC1 */
{3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
@@ -233,13 +233,11 @@
static int __init declare_of_platform_devices(void)
{
- if (!machine_is(mpc85xx_ads))
- return 0;
-
of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
return 0;
}
-device_initcall(declare_of_platform_devices);
+machine_device_initcall(mpc85xx_ads, declare_of_platform_devices);
/*
* Called very early, device-tree isn't unflattened
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.c b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
index 4d063ee..8b1de78 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_cds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
@@ -222,9 +222,6 @@
struct device_node *cascade_node = NULL;
int cascade_irq;
- if (!machine_is(mpc85xx_cds))
- return 0;
-
/* Initialize the i8259 controller */
for_each_node_by_type(np, "interrupt-controller")
if (of_device_is_compatible(np, "chrp,iic")) {
@@ -262,8 +259,7 @@
return 0;
}
-
-device_initcall(mpc85xx_cds_8259_attach);
+machine_device_initcall(mpc85xx_cds, mpc85xx_cds_8259_attach);
#endif /* CONFIG_PPC_I8259 */
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index e6c63a5..4fdf5ab 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -144,15 +144,12 @@
static int __init mpc85xx_publish_devices(void)
{
- if (!machine_is(mpc85xx_mds))
- return 0;
-
/* Publish the QE devices */
- of_platform_bus_probe(NULL,mpc85xx_ids,NULL);
+ of_platform_bus_probe(NULL, mpc85xx_ids, NULL);
return 0;
}
-device_initcall(mpc85xx_publish_devices);
+machine_device_initcall(mpc85xx_mds, mpc85xx_publish_devices);
static void __init mpc85xx_mds_pic_init(void)
{
diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
index c6d2f48..0b07485 100644
--- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
+++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
@@ -34,9 +34,24 @@
#include <asm/mpic.h>
+#include <linux/of_platform.h>
#include <sysdev/fsl_pci.h>
#include <sysdev/fsl_soc.h>
+static struct of_device_id __initdata mpc8610_ids[] = {
+ { .compatible = "fsl,mpc8610-immr", },
+ {}
+};
+
+static int __init mpc8610_declare_of_platform_devices(void)
+{
+ /* Without this call, the SSI device driver won't get probed. */
+ of_platform_bus_probe(NULL, mpc8610_ids, NULL);
+
+ return 0;
+}
+machine_device_initcall(mpc86xx_hpcd, mpc8610_declare_of_platform_devices);
+
void __init
mpc86xx_hpcd_init_irq(void)
{
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index 14f4e52..cfbe8c5 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -18,6 +18,7 @@
#include <linux/kdev_t.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
+#include <linux/of_platform.h>
#include <asm/system.h>
#include <asm/time.h>
@@ -212,6 +213,19 @@
return 0;
}
+static __initdata struct of_device_id of_bus_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
+ return 0;
+}
+machine_device_initcall(mpc86xx_hpcn, declare_of_platform_devices);
+
define_machine(mpc86xx_hpcn) {
.name = "MPC86xx HPCN",
.probe = mpc86xx_hpcn_probe,
diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig
index 91fbe42..7fd224c 100644
--- a/arch/powerpc/platforms/8xx/Kconfig
+++ b/arch/powerpc/platforms/8xx/Kconfig
@@ -44,6 +44,15 @@
This board is also resold by Freescale as the QUICCStart
MPC885 Evaluation System and/or the CWH-PPC-885XN-VE.
+config PPC_ADDER875
+ bool "Analogue & Micro Adder 875"
+ select CPM1
+ select PPC_CPM_NEW_BINDING
+ select REDBOOT
+ help
+ This enables support for the Analogue & Micro Adder 875
+ board.
+
endchoice
menu "Freescale Ethernet driver platform-specific options"
diff --git a/arch/powerpc/platforms/8xx/Makefile b/arch/powerpc/platforms/8xx/Makefile
index 8b70980..7b71d9c 100644
--- a/arch/powerpc/platforms/8xx/Makefile
+++ b/arch/powerpc/platforms/8xx/Makefile
@@ -5,3 +5,4 @@
obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
obj-$(CONFIG_MPC86XADS) += mpc86xads_setup.o
obj-$(CONFIG_PPC_EP88XC) += ep88xc.o
+obj-$(CONFIG_PPC_ADDER875) += adder875.o
diff --git a/arch/powerpc/platforms/8xx/adder875.c b/arch/powerpc/platforms/8xx/adder875.c
new file mode 100644
index 0000000..c6bc078
--- /dev/null
+++ b/arch/powerpc/platforms/8xx/adder875.c
@@ -0,0 +1,118 @@
+/* Analogue & Micro Adder MPC875 board support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/commproc.h>
+#include <asm/fs_pd.h>
+#include <asm/udbg.h>
+#include <asm/prom.h>
+
+#include <sysdev/commproc.h>
+
+struct cpm_pin {
+ int port, pin, flags;
+};
+
+static __initdata struct cpm_pin adder875_pins[] = {
+ /* SMC1 */
+ {CPM_PORTB, 24, CPM_PIN_INPUT}, /* RX */
+ {CPM_PORTB, 25, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* TX */
+
+ /* MII1 */
+ {CPM_PORTA, 0, CPM_PIN_INPUT},
+ {CPM_PORTA, 1, CPM_PIN_INPUT},
+ {CPM_PORTA, 2, CPM_PIN_INPUT},
+ {CPM_PORTA, 3, CPM_PIN_INPUT},
+ {CPM_PORTA, 4, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 10, CPM_PIN_OUTPUT},
+ {CPM_PORTA, 11, CPM_PIN_OUTPUT},
+ {CPM_PORTB, 19, CPM_PIN_INPUT},
+ {CPM_PORTB, 31, CPM_PIN_INPUT},
+ {CPM_PORTC, 12, CPM_PIN_INPUT},
+ {CPM_PORTC, 13, CPM_PIN_INPUT},
+ {CPM_PORTE, 30, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 31, CPM_PIN_OUTPUT},
+
+ /* MII2 */
+ {CPM_PORTE, 14, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 15, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 16, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 17, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 18, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 19, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 20, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+ {CPM_PORTE, 21, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 22, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 23, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 24, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 25, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 26, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 27, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 28, CPM_PIN_OUTPUT},
+ {CPM_PORTE, 29, CPM_PIN_OUTPUT},
+};
+
+static void __init init_ioports(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(adder875_pins); i++) {
+ const struct cpm_pin *pin = &adder875_pins[i];
+ cpm1_set_pin(pin->port, pin->pin, pin->flags);
+ }
+
+ cpm1_clk_setup(CPM_CLK_SMC1, CPM_BRG1, CPM_CLK_RTX);
+
+ /* Set FEC1 and FEC2 to MII mode */
+ clrbits32(&mpc8xx_immr->im_cpm.cp_cptr, 0x00000180);
+}
+
+static void __init adder875_setup(void)
+{
+ cpm_reset();
+ init_ioports();
+}
+
+static int __init adder875_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ return of_flat_dt_is_compatible(root, "analogue-and-micro,adder875");
+}
+
+static __initdata struct of_device_id of_bus_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ return 0;
+}
+machine_device_initcall(adder875, declare_of_platform_devices);
+
+define_machine(adder875) {
+ .name = "Adder MPC875",
+ .probe = adder875_probe,
+ .setup_arch = adder875_setup,
+ .init_IRQ = m8xx_pic_init,
+ .get_irq = mpc8xx_get_irq,
+ .restart = mpc8xx_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .set_rtc_time = mpc8xx_set_rtc_time,
+ .get_rtc_time = mpc8xx_get_rtc_time,
+ .progress = udbg_progress,
+};
diff --git a/arch/powerpc/platforms/8xx/ep88xc.c b/arch/powerpc/platforms/8xx/ep88xc.c
index c518b6c..88afa35 100644
--- a/arch/powerpc/platforms/8xx/ep88xc.c
+++ b/arch/powerpc/platforms/8xx/ep88xc.c
@@ -155,12 +155,11 @@
static int __init declare_of_platform_devices(void)
{
/* Publish the QE devices */
- if (machine_is(ep88xc))
- of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
return 0;
}
-device_initcall(declare_of_platform_devices);
+machine_device_initcall(ep88xc, declare_of_platform_devices);
define_machine(ep88xc) {
.name = "Embedded Planet EP88xC",
diff --git a/arch/powerpc/platforms/8xx/mpc86xads_setup.c b/arch/powerpc/platforms/8xx/mpc86xads_setup.c
index d2927a4..d7965f8 100644
--- a/arch/powerpc/platforms/8xx/mpc86xads_setup.c
+++ b/arch/powerpc/platforms/8xx/mpc86xads_setup.c
@@ -128,12 +128,11 @@
static int __init declare_of_platform_devices(void)
{
- if (machine_is(mpc86x_ads))
- of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
return 0;
}
-device_initcall(declare_of_platform_devices);
+machine_device_initcall(mpc86x_ads, declare_of_platform_devices);
define_machine(mpc86x_ads) {
.name = "MPC86x ADS",
diff --git a/arch/powerpc/platforms/8xx/mpc885ads_setup.c b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
index 2cf1b6a..6ef8e9e 100644
--- a/arch/powerpc/platforms/8xx/mpc885ads_setup.c
+++ b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
@@ -264,12 +264,11 @@
static int __init declare_of_platform_devices(void)
{
/* Publish the QE devices */
- if (machine_is(mpc885_ads))
- of_platform_bus_probe(NULL, of_bus_ids, NULL);
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
return 0;
}
-device_initcall(declare_of_platform_devices);
+machine_device_initcall(mpc885_ads, declare_of_platform_devices);
define_machine(mpc885_ads) {
.name = "Freescale MPC885 ADS",
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index ea22cad..2cec3431 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -22,6 +22,7 @@
depends on 6xx
select FSL_SOC
select 83xx
+ select IPIC
select WANT_DEVICE_TREE
config PPC_86xx
@@ -80,6 +81,10 @@
bool
default y
+config IPIC
+ bool
+ default n
+
config MPIC
bool
default n
@@ -265,6 +270,7 @@
config QUICC_ENGINE
bool
select PPC_LIB_RHEAP
+ select CRC32
help
The QUICC Engine (QE) is a new generation of communications
coprocessors on Freescale embedded CPUs (akin to CPM in older chips).
diff --git a/arch/powerpc/platforms/embedded6xx/Kconfig b/arch/powerpc/platforms/embedded6xx/Kconfig
index 8924095..6c80837 100644
--- a/arch/powerpc/platforms/embedded6xx/Kconfig
+++ b/arch/powerpc/platforms/embedded6xx/Kconfig
@@ -9,6 +9,8 @@
select FSL_SOC
select PPC_UDBG_16550 if SERIAL_8250
select DEFAULT_UIMAGE
+ select MPC10X_OPENPIC
+ select MPC10X_BRIDGE
help
Select LINKSTATION if configuring for one of PPC- (MPC8241)
based NAS systems from Buffalo Technology. So far only
@@ -16,6 +18,19 @@
Linkstation-I HD-HLAN and HD-HGLAN versions, and PPC-based
Terastation systems should be supported too.
+config STORCENTER
+ bool "IOMEGA StorCenter"
+ depends on EMBEDDED6xx
+ select MPIC
+ select FSL_SOC
+ select PPC_UDBG_16550 if SERIAL_8250
+ select WANT_DEVICE_TREE
+ select MPC10X_OPENPIC
+ select MPC10X_BRIDGE
+ help
+ Select STORCENTER if configuring for the iomega StorCenter
+ with an 8241 CPU in it.
+
config MPC7448HPC2
bool "Freescale MPC7448HPC2(Taiga)"
depends on EMBEDDED6xx
@@ -23,6 +38,7 @@
select DEFAULT_UIMAGE
select PPC_UDBG_16550
select WANT_DEVICE_TREE
+ select TSI108_BRIDGE
help
Select MPC7448HPC2 if configuring for Freescale MPC7448HPC2 (Taiga)
platform
@@ -33,6 +49,7 @@
select TSI108_BRIDGE
select PPC_UDBG_16550
select WANT_DEVICE_TREE
+ select TSI108_BRIDGE
help
Select PPC_HOLLY if configuring for an IBM 750GX/CL Eval
Board with TSI108/9 bridge (Hickory/Holly)
@@ -48,17 +65,13 @@
config TSI108_BRIDGE
bool
- depends on MPC7448HPC2 || PPC_HOLLY
select PCI
select MPIC
select MPIC_WEIRD
- default y
config MPC10X_BRIDGE
bool
- depends on LINKSTATION
select PPC_INDIRECT_PCI
- default y
config MV64X60
bool
@@ -67,8 +80,6 @@
config MPC10X_OPENPIC
bool
- depends on LINKSTATION
- default y
config MPC10X_STORE_GATHERING
bool "Enable MPC10x store gathering"
diff --git a/arch/powerpc/platforms/embedded6xx/Makefile b/arch/powerpc/platforms/embedded6xx/Makefile
index 844947c..06524d3 100644
--- a/arch/powerpc/platforms/embedded6xx/Makefile
+++ b/arch/powerpc/platforms/embedded6xx/Makefile
@@ -3,5 +3,6 @@
#
obj-$(CONFIG_MPC7448HPC2) += mpc7448_hpc2.o
obj-$(CONFIG_LINKSTATION) += linkstation.o ls_uart.o
+obj-$(CONFIG_STORCENTER) += storcenter.o
obj-$(CONFIG_PPC_HOLLY) += holly.o
obj-$(CONFIG_PPC_PRPMC2800) += prpmc2800.o
diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
index a2c04b9..d4f8bf5 100644
--- a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
+++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
@@ -53,8 +53,6 @@
#define MPC7448HPC2_PCI_CFG_PHYS 0xfb000000
-extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
-
int mpc7448_hpc2_exclude_device(struct pci_controller *hose,
u_char bus, u_char devfn)
{
diff --git a/arch/powerpc/platforms/embedded6xx/storcenter.c b/arch/powerpc/platforms/embedded6xx/storcenter.c
new file mode 100644
index 0000000..e12e9d2
--- /dev/null
+++ b/arch/powerpc/platforms/embedded6xx/storcenter.c
@@ -0,0 +1,192 @@
+/*
+ * Board setup routines for the storcenter
+ *
+ * Copyright 2007 (C) Oyvind Repvik (nail@nslu2-linux.org)
+ * Copyright 2007 Andy Wilcox, Jon Loeliger
+ *
+ * Based on linkstation.c by G. Liakhovetski
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of
+ * any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/initrd.h>
+#include <linux/mtd/physmap.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+#include <asm/mpic.h>
+#include <asm/pci-bridge.h>
+
+#include "mpc10x.h"
+
+
+#ifdef CONFIG_MTD_PHYSMAP
+static struct mtd_partition storcenter_physmap_partitions[] = {
+ {
+ .name = "kernel",
+ .offset = 0x000000,
+ .size = 0x170000,
+ },
+ {
+ .name = "rootfs",
+ .offset = 0x170000,
+ .size = 0x590000,
+ },
+ {
+ .name = "uboot",
+ .offset = 0x700000,
+ .size = 0x040000,
+ },
+ {
+ .name = "config",
+ .offset = 0x740000,
+ .size = 0x0c0000,
+ },
+};
+#endif
+
+
+static __initdata struct of_device_id storcenter_of_bus[] = {
+ { .name = "soc", },
+ {},
+};
+
+static int __init storcenter_device_probe(void)
+{
+ of_platform_bus_probe(NULL, storcenter_of_bus, NULL);
+ return 0;
+}
+machine_device_initcall(storcenter, storcenter_device_probe);
+
+
+static int __init storcenter_add_bridge(struct device_node *dev)
+{
+#ifdef CONFIG_PCI
+ int len;
+ struct pci_controller *hose;
+ const int *bus_range;
+
+ printk("Adding PCI host bridge %s\n", dev->full_name);
+
+ hose = pcibios_alloc_controller(dev);
+ if (hose == NULL)
+ return -ENOMEM;
+
+ bus_range = of_get_property(dev, "bus-range", &len);
+ hose->first_busno = bus_range ? bus_range[0] : 0;
+ hose->last_busno = bus_range ? bus_range[1] : 0xff;
+
+ setup_indirect_pci(hose, MPC10X_MAPB_CNFG_ADDR, MPC10X_MAPB_CNFG_DATA, 0);
+
+ /* Interpret the "ranges" property */
+ /* This also maps the I/O region and sets isa_io/mem_base */
+ pci_process_bridge_OF_ranges(hose, dev, 1);
+#endif
+
+ return 0;
+}
+
+static void __init storcenter_setup_arch(void)
+{
+ struct device_node *np;
+
+#ifdef CONFIG_MTD_PHYSMAP
+ physmap_set_partitions(storcenter_physmap_partitions,
+ ARRAY_SIZE(storcenter_physmap_partitions));
+#endif
+
+ /* Lookup PCI host bridges */
+ for_each_compatible_node(np, "pci", "mpc10x-pci")
+ storcenter_add_bridge(np);
+
+ printk(KERN_INFO "IOMEGA StorCenter\n");
+}
+
+/*
+ * Interrupt setup and service. Interrrupts on the turbostation come
+ * from the four PCI slots plus onboard 8241 devices: I2C, DUART.
+ */
+static void __init storcenter_init_IRQ(void)
+{
+ struct mpic *mpic;
+ struct device_node *dnp;
+ const void *prop;
+ int size;
+ phys_addr_t paddr;
+
+ dnp = of_find_node_by_type(NULL, "open-pic");
+ if (dnp == NULL)
+ return;
+
+ prop = of_get_property(dnp, "reg", &size);
+ if (prop == NULL) {
+ of_node_put(dnp);
+ return;
+ }
+
+ paddr = (phys_addr_t)of_translate_address(dnp, prop);
+ mpic = mpic_alloc(dnp, paddr, MPIC_PRIMARY | MPIC_WANTS_RESET,
+ 4, 32, " EPIC ");
+
+ of_node_put(dnp);
+
+ BUG_ON(mpic == NULL);
+
+ /* PCI IRQs */
+ /*
+ * 2.6.12 patch:
+ * openpic_set_sources(0, 5, OpenPIC_Addr + 0x10200);
+ * openpic_set_sources(5, 2, OpenPIC_Addr + 0x11120);
+ * first_irq, num_irqs, __iomem first_ISR
+ * o_ss: i, src: 0, fdf50200
+ * o_ss: i, src: 1, fdf50220
+ * o_ss: i, src: 2, fdf50240
+ * o_ss: i, src: 3, fdf50260
+ * o_ss: i, src: 4, fdf50280
+ * o_ss: i, src: 5, fdf51120
+ * o_ss: i, src: 6, fdf51140
+ */
+ mpic_assign_isu(mpic, 0, paddr + 0x10200);
+ mpic_assign_isu(mpic, 1, paddr + 0x10220);
+ mpic_assign_isu(mpic, 2, paddr + 0x10240);
+ mpic_assign_isu(mpic, 3, paddr + 0x10260);
+ mpic_assign_isu(mpic, 4, paddr + 0x10280);
+ mpic_assign_isu(mpic, 5, paddr + 0x11120);
+ mpic_assign_isu(mpic, 6, paddr + 0x11140);
+
+ mpic_init(mpic);
+}
+
+static void storcenter_restart(char *cmd)
+{
+ local_irq_disable();
+
+ /* Set exception prefix high - to the firmware */
+ _nmask_and_or_msr(0, MSR_IP);
+
+ /* Wait for reset to happen */
+ for (;;) ;
+}
+
+static int __init storcenter_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "storcenter");
+}
+
+define_machine(storcenter){
+ .name = "IOMEGA StorCenter",
+ .probe = storcenter_probe,
+ .setup_arch = storcenter_setup_arch,
+ .init_IRQ = storcenter_init_IRQ,
+ .get_irq = mpic_get_irq,
+ .restart = storcenter_restart,
+ .calibrate_decr = generic_calibrate_decr,
+};
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index 9a20ef4..f17e7b8 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -12,6 +12,7 @@
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
obj-$(CONFIG_FSL_PCI) += fsl_pci.o
+obj-$(CONFIG_RAPIDIO) += fsl_rio.o
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
obj-$(CONFIG_PPC_BESTCOMM) += bestcomm/
@@ -24,7 +25,7 @@
ifeq ($(CONFIG_PPC_MERGE),y)
obj-$(CONFIG_PPC_INDIRECT_PCI) += indirect_pci.o
obj-$(CONFIG_PPC_I8259) += i8259.o
-obj-$(CONFIG_PPC_83xx) += ipic.o
+obj-$(CONFIG_IPIC) += ipic.o
obj-$(CONFIG_4xx) += uic.o
obj-$(CONFIG_XILINX_VIRTEX) += xilinx_intc.o
ifeq ($(CONFIG_PCI),y)
diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c
index 4b1d512..bf13c21 100644
--- a/arch/powerpc/sysdev/fsl_pci.c
+++ b/arch/powerpc/sysdev/fsl_pci.c
@@ -33,8 +33,8 @@
struct ccsr_pci __iomem *pci;
int i;
- pr_debug("PCI memory map start 0x%x, size 0x%x\n", rsrc->start,
- rsrc->end - rsrc->start + 1);
+ pr_debug("PCI memory map start 0x%016llx, size 0x%016llx\n",
+ (u64)rsrc->start, (u64)rsrc->end - (u64)rsrc->start + 1);
pci = ioremap(rsrc->start, rsrc->end - rsrc->start + 1);
/* Disable all windows (except powar0 since its ignored) */
@@ -46,17 +46,17 @@
/* Setup outbound MEM window */
for(i = 0; i < 3; i++)
if (hose->mem_resources[i].flags & IORESOURCE_MEM){
- pr_debug("PCI MEM resource start 0x%08x, size 0x%08x.\n",
- hose->mem_resources[i].start,
- hose->mem_resources[i].end
- - hose->mem_resources[i].start + 1);
- out_be32(&pci->pow[i+1].potar,
- (hose->mem_resources[i].start >> 12)
- & 0x000fffff);
+ resource_size_t pci_addr_start =
+ hose->mem_resources[i].start -
+ hose->pci_mem_offset;
+ pr_debug("PCI MEM resource start 0x%016llx, size 0x%016llx.\n",
+ (u64)hose->mem_resources[i].start,
+ (u64)hose->mem_resources[i].end
+ - (u64)hose->mem_resources[i].start + 1);
+ out_be32(&pci->pow[i+1].potar, (pci_addr_start >> 12));
out_be32(&pci->pow[i+1].potear, 0);
out_be32(&pci->pow[i+1].powbar,
- (hose->mem_resources[i].start >> 12)
- & 0x000fffff);
+ (hose->mem_resources[i].start >> 12));
/* Enable, Mem R/W */
out_be32(&pci->pow[i+1].powar, 0x80044000
| (__ilog2(hose->mem_resources[i].end
@@ -65,15 +65,14 @@
/* Setup outbound IO window */
if (hose->io_resource.flags & IORESOURCE_IO){
- pr_debug("PCI IO resource start 0x%08x, size 0x%08x, phy base 0x%08x.\n",
- hose->io_resource.start,
- hose->io_resource.end - hose->io_resource.start + 1,
- hose->io_base_phys);
- out_be32(&pci->pow[i+1].potar, (hose->io_resource.start >> 12)
- & 0x000fffff);
+ pr_debug("PCI IO resource start 0x%016llx, size 0x%016llx, "
+ "phy base 0x%016llx.\n",
+ (u64)hose->io_resource.start,
+ (u64)hose->io_resource.end - (u64)hose->io_resource.start + 1,
+ (u64)hose->io_base_phys);
+ out_be32(&pci->pow[i+1].potar, (hose->io_resource.start >> 12));
out_be32(&pci->pow[i+1].potear, 0);
- out_be32(&pci->pow[i+1].powbar, (hose->io_base_phys >> 12)
- & 0x000fffff);
+ out_be32(&pci->pow[i+1].powbar, (hose->io_base_phys >> 12));
/* Enable, IO R/W */
out_be32(&pci->pow[i+1].powar, 0x80088000
| (__ilog2(hose->io_resource.end
@@ -107,55 +106,17 @@
}
}
-static void __init quirk_fsl_pcie_transparent(struct pci_dev *dev)
-{
- struct resource *res;
- int i, res_idx = PCI_BRIDGE_RESOURCES;
- struct pci_controller *hose;
+static int fsl_pcie_bus_fixup;
+static void __init quirk_fsl_pcie_header(struct pci_dev *dev)
+{
/* if we aren't a PCIe don't bother */
if (!pci_find_capability(dev, PCI_CAP_ID_EXP))
return ;
- /*
- * Make the bridge be transparent.
- */
- dev->transparent = 1;
-
- hose = pci_bus_to_host(dev->bus);
- if (!hose) {
- printk(KERN_ERR "Can't find hose for bus %d\n",
- dev->bus->number);
- return;
- }
-
- /* Clear out any of the virtual P2P bridge registers */
- pci_write_config_word(dev, PCI_IO_BASE_UPPER16, 0);
- pci_write_config_word(dev, PCI_IO_LIMIT_UPPER16, 0);
- pci_write_config_byte(dev, PCI_IO_BASE, 0x10);
- pci_write_config_byte(dev, PCI_IO_LIMIT, 0);
- pci_write_config_word(dev, PCI_MEMORY_BASE, 0x10);
- pci_write_config_word(dev, PCI_MEMORY_LIMIT, 0);
- pci_write_config_word(dev, PCI_PREF_BASE_UPPER32, 0x0);
- pci_write_config_word(dev, PCI_PREF_LIMIT_UPPER32, 0x0);
- pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, 0x10);
- pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, 0);
-
- if (hose->io_resource.flags) {
- res = &dev->resource[res_idx++];
- res->start = hose->io_resource.start;
- res->end = hose->io_resource.end;
- res->flags = hose->io_resource.flags;
- update_bridge_resource(dev, res);
- }
-
- for (i = 0; i < 3; i++) {
- res = &dev->resource[res_idx + i];
- res->start = hose->mem_resources[i].start;
- res->end = hose->mem_resources[i].end;
- res->flags = hose->mem_resources[i].flags;
- update_bridge_resource(dev, res);
- }
+ dev->class = PCI_CLASS_BRIDGE_PCI << 8;
+ fsl_pcie_bus_fixup = 1;
+ return ;
}
int __init fsl_pcie_check_link(struct pci_controller *hose)
@@ -172,11 +133,24 @@
struct pci_controller *hose = (struct pci_controller *) bus->sysdata;
int i;
- /* deal with bogus pci_bus when we don't have anything connected on PCIe */
- if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK) {
- if (bus->parent) {
- for (i = 0; i < 4; ++i)
- bus->resource[i] = bus->parent->resource[i];
+ if ((bus->parent == hose->bus) &&
+ ((fsl_pcie_bus_fixup &&
+ early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) ||
+ (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK)))
+ {
+ for (i = 0; i < 4; ++i) {
+ struct resource *res = bus->resource[i];
+ struct resource *par = bus->parent->resource[i];
+ if (res) {
+ res->start = 0;
+ res->end = 0;
+ res->flags = 0;
+ }
+ if (res && par) {
+ res->start = par->start;
+ res->end = par->end;
+ res->flags = par->flags;
+ }
}
}
}
@@ -240,23 +214,23 @@
return 0;
}
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8548E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8548, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8543E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8543, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8547E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8545E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8545, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8568E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8568, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8567E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8567, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8533E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8533, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8544E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8544, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8572E, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8572, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8641, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8641D, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8610, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8548E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8548, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8543E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8543, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8547E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8545E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8545, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8568E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8568, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8567E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8567, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8533E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8533, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8544E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8544, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8572E, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8572, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8641, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8641D, quirk_fsl_pcie_header);
+DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8610, quirk_fsl_pcie_header);
diff --git a/arch/ppc/syslib/ppc85xx_rio.c b/arch/powerpc/sysdev/fsl_rio.c
similarity index 100%
rename from arch/ppc/syslib/ppc85xx_rio.c
rename to arch/powerpc/sysdev/fsl_rio.c
diff --git a/arch/ppc/syslib/ppc85xx_rio.h b/arch/powerpc/sysdev/fsl_rio.h
similarity index 100%
rename from arch/ppc/syslib/ppc85xx_rio.h
rename to arch/powerpc/sysdev/fsl_rio.h
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index 217bcc2..f2c0988 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -24,6 +24,7 @@
#include <linux/platform_device.h>
#include <linux/of_platform.h>
#include <linux/phy.h>
+#include <linux/phy_fixed.h>
#include <linux/spi/spi.h>
#include <linux/fsl_devices.h>
#include <linux/fs_enet_pd.h>
@@ -54,10 +55,18 @@
soc = of_find_node_by_type(NULL, "soc");
if (soc) {
int size;
- const void *prop = of_get_property(soc, "reg", &size);
+ u32 naddr;
+ const u32 *prop = of_get_property(soc, "#address-cells", &size);
+ if (prop && size == 4)
+ naddr = *prop;
+ else
+ naddr = 2;
+
+ prop = of_get_property(soc, "ranges", &size);
if (prop)
- immrbase = of_translate_address(soc, prop);
+ immrbase = of_translate_address(soc, prop + naddr);
+
of_node_put(soc);
}
@@ -130,6 +139,37 @@
EXPORT_SYMBOL(get_baudrate);
#endif /* CONFIG_CPM2 */
+#ifdef CONFIG_FIXED_PHY
+static int __init of_add_fixed_phys(void)
+{
+ int ret;
+ struct device_node *np;
+ u32 *fixed_link;
+ struct fixed_phy_status status = {};
+
+ for_each_node_by_name(np, "ethernet") {
+ fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL);
+ if (!fixed_link)
+ continue;
+
+ status.link = 1;
+ status.duplex = fixed_link[1];
+ status.speed = fixed_link[2];
+ status.pause = fixed_link[3];
+ status.asym_pause = fixed_link[4];
+
+ ret = fixed_phy_add(PHY_POLL, fixed_link[0], &status);
+ if (ret) {
+ of_node_put(np);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+arch_initcall(of_add_fixed_phys);
+#endif /* CONFIG_FIXED_PHY */
+
static int __init gfar_mdio_of_init(void)
{
struct device_node *np = NULL;
@@ -198,7 +238,6 @@
static const char *gfar_rx_intr = "rx";
static const char *gfar_err_intr = "error";
-
static int __init gfar_of_init(void)
{
struct device_node *np;
@@ -282,29 +321,43 @@
gfar_data.interface = PHY_INTERFACE_MODE_MII;
ph = of_get_property(np, "phy-handle", NULL);
- phy = of_find_node_by_phandle(*ph);
+ if (ph == NULL) {
+ u32 *fixed_link;
- if (phy == NULL) {
- ret = -ENODEV;
- goto unreg;
- }
+ fixed_link = (u32 *)of_get_property(np, "fixed-link",
+ NULL);
+ if (!fixed_link) {
+ ret = -ENODEV;
+ goto unreg;
+ }
- mdio = of_get_parent(phy);
+ gfar_data.bus_id = 0;
+ gfar_data.phy_id = fixed_link[0];
+ } else {
+ phy = of_find_node_by_phandle(*ph);
- id = of_get_property(phy, "reg", NULL);
- ret = of_address_to_resource(mdio, 0, &res);
- if (ret) {
+ if (phy == NULL) {
+ ret = -ENODEV;
+ goto unreg;
+ }
+
+ mdio = of_get_parent(phy);
+
+ id = of_get_property(phy, "reg", NULL);
+ ret = of_address_to_resource(mdio, 0, &res);
+ if (ret) {
+ of_node_put(phy);
+ of_node_put(mdio);
+ goto unreg;
+ }
+
+ gfar_data.phy_id = *id;
+ gfar_data.bus_id = res.start;
+
of_node_put(phy);
of_node_put(mdio);
- goto unreg;
}
- gfar_data.phy_id = *id;
- gfar_data.bus_id = res.start;
-
- of_node_put(phy);
- of_node_put(mdio);
-
ret =
platform_device_add_data(gfar_dev, &gfar_data,
sizeof(struct
@@ -531,14 +584,12 @@
static int __init fsl_usb_of_init(void)
{
struct device_node *np;
- unsigned int i;
+ unsigned int i = 0;
struct platform_device *usb_dev_mph = NULL, *usb_dev_dr_host = NULL,
*usb_dev_dr_client = NULL;
int ret;
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "usb", "fsl-usb2-mph")) != NULL;
- i++) {
+ for_each_compatible_node(np, NULL, "fsl-usb2-mph") {
struct resource r[2];
struct fsl_usb2_platform_data usb_data;
const unsigned char *prop = NULL;
@@ -581,11 +632,10 @@
fsl_usb2_platform_data));
if (ret)
goto unreg_mph;
+ i++;
}
- for (np = NULL;
- (np = of_find_compatible_node(np, "usb", "fsl-usb2-dr")) != NULL;
- i++) {
+ for_each_compatible_node(np, NULL, "fsl-usb2-dr") {
struct resource r[2];
struct fsl_usb2_platform_data usb_data;
const unsigned char *prop = NULL;
@@ -657,6 +707,7 @@
fsl_usb2_platform_data))))
goto unreg_dr;
}
+ i++;
}
return 0;
diff --git a/arch/powerpc/sysdev/ipic.c b/arch/powerpc/sysdev/ipic.c
index 7274750..4c016da 100644
--- a/arch/powerpc/sysdev/ipic.c
+++ b/arch/powerpc/sysdev/ipic.c
@@ -48,6 +48,13 @@
.bit = 17,
.prio_mask = 1,
},
+ [3] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_C,
+ .force = IPIC_SIFCR_H,
+ .bit = 18,
+ .prio_mask = 2,
+ },
[4] = {
.mask = IPIC_SIMSR_H,
.prio = IPIC_SIPRR_C,
@@ -55,6 +62,34 @@
.bit = 19,
.prio_mask = 3,
},
+ [5] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_C,
+ .force = IPIC_SIFCR_H,
+ .bit = 20,
+ .prio_mask = 4,
+ },
+ [6] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_C,
+ .force = IPIC_SIFCR_H,
+ .bit = 21,
+ .prio_mask = 5,
+ },
+ [7] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_C,
+ .force = IPIC_SIFCR_H,
+ .bit = 22,
+ .prio_mask = 6,
+ },
+ [8] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_C,
+ .force = IPIC_SIFCR_H,
+ .bit = 23,
+ .prio_mask = 7,
+ },
[9] = {
.mask = IPIC_SIMSR_H,
.prio = IPIC_SIPRR_D,
@@ -223,6 +258,20 @@
.bit = 7,
.prio_mask = 7,
},
+ [40] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_B,
+ .force = IPIC_SIFCR_H,
+ .bit = 8,
+ .prio_mask = 0,
+ },
+ [41] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_B,
+ .force = IPIC_SIFCR_H,
+ .bit = 9,
+ .prio_mask = 1,
+ },
[42] = {
.mask = IPIC_SIMSR_H,
.prio = IPIC_SIPRR_B,
@@ -230,6 +279,13 @@
.bit = 10,
.prio_mask = 2,
},
+ [43] = {
+ .mask = IPIC_SIMSR_H,
+ .prio = IPIC_SIPRR_B,
+ .force = IPIC_SIFCR_H,
+ .bit = 11,
+ .prio_mask = 3,
+ },
[44] = {
.mask = IPIC_SIMSR_H,
.prio = IPIC_SIPRR_B,
@@ -387,6 +443,12 @@
.force = IPIC_SIFCR_L,
.bit = 18,
},
+ [83] = {
+ .mask = IPIC_SIMSR_L,
+ .prio = 0,
+ .force = IPIC_SIFCR_L,
+ .bit = 19,
+ },
[84] = {
.mask = IPIC_SIMSR_L,
.prio = 0,
diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c
index f88ff09..0da7069 100644
--- a/arch/powerpc/sysdev/mpic.c
+++ b/arch/powerpc/sysdev/mpic.c
@@ -267,7 +267,7 @@
*/
-static void _mpic_map_mmio(struct mpic *mpic, unsigned long phys_addr,
+static void _mpic_map_mmio(struct mpic *mpic, phys_addr_t phys_addr,
struct mpic_reg_bank *rb, unsigned int offset,
unsigned int size)
{
@@ -287,7 +287,7 @@
BUG_ON(!DCR_MAP_OK(rb->dhost));
}
-static inline void mpic_map(struct mpic *mpic, unsigned long phys_addr,
+static inline void mpic_map(struct mpic *mpic, phys_addr_t phys_addr,
struct mpic_reg_bank *rb, unsigned int offset,
unsigned int size)
{
diff --git a/arch/powerpc/sysdev/qe_lib/Kconfig b/arch/powerpc/sysdev/qe_lib/Kconfig
index f611d34..adc6621 100644
--- a/arch/powerpc/sysdev/qe_lib/Kconfig
+++ b/arch/powerpc/sysdev/qe_lib/Kconfig
@@ -4,7 +4,7 @@
config UCC_SLOW
bool
- default n
+ default y if SERIAL_QE
help
This option provides qe_lib support to UCC slow
protocols: UART, BISYNC, QMC
diff --git a/arch/powerpc/sysdev/qe_lib/qe.c b/arch/powerpc/sysdev/qe_lib/qe.c
index 21e0106..3925eae 100644
--- a/arch/powerpc/sysdev/qe_lib/qe.c
+++ b/arch/powerpc/sysdev/qe_lib/qe.c
@@ -25,6 +25,7 @@
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/ioport.h>
+#include <linux/crc32.h>
#include <asm/irq.h>
#include <asm/page.h>
#include <asm/pgtable.h>
@@ -394,3 +395,249 @@
return (void *)&qe_immr->muram[offset];
}
EXPORT_SYMBOL(qe_muram_addr);
+
+/* The maximum number of RISCs we support */
+#define MAX_QE_RISC 2
+
+/* Firmware information stored here for qe_get_firmware_info() */
+static struct qe_firmware_info qe_firmware_info;
+
+/*
+ * Set to 1 if QE firmware has been uploaded, and therefore
+ * qe_firmware_info contains valid data.
+ */
+static int qe_firmware_uploaded;
+
+/*
+ * Upload a QE microcode
+ *
+ * This function is a worker function for qe_upload_firmware(). It does
+ * the actual uploading of the microcode.
+ */
+static void qe_upload_microcode(const void *base,
+ const struct qe_microcode *ucode)
+{
+ const __be32 *code = base + be32_to_cpu(ucode->code_offset);
+ unsigned int i;
+
+ if (ucode->major || ucode->minor || ucode->revision)
+ printk(KERN_INFO "qe-firmware: "
+ "uploading microcode '%s' version %u.%u.%u\n",
+ ucode->id, ucode->major, ucode->minor, ucode->revision);
+ else
+ printk(KERN_INFO "qe-firmware: "
+ "uploading microcode '%s'\n", ucode->id);
+
+ /* Use auto-increment */
+ out_be32(&qe_immr->iram.iadd, be32_to_cpu(ucode->iram_offset) |
+ QE_IRAM_IADD_AIE | QE_IRAM_IADD_BADDR);
+
+ for (i = 0; i < be32_to_cpu(ucode->count); i++)
+ out_be32(&qe_immr->iram.idata, be32_to_cpu(code[i]));
+}
+
+/*
+ * Upload a microcode to the I-RAM at a specific address.
+ *
+ * See Documentation/powerpc/qe-firmware.txt for information on QE microcode
+ * uploading.
+ *
+ * Currently, only version 1 is supported, so the 'version' field must be
+ * set to 1.
+ *
+ * The SOC model and revision are not validated, they are only displayed for
+ * informational purposes.
+ *
+ * 'calc_size' is the calculated size, in bytes, of the firmware structure and
+ * all of the microcode structures, minus the CRC.
+ *
+ * 'length' is the size that the structure says it is, including the CRC.
+ */
+int qe_upload_firmware(const struct qe_firmware *firmware)
+{
+ unsigned int i;
+ unsigned int j;
+ u32 crc;
+ size_t calc_size = sizeof(struct qe_firmware);
+ size_t length;
+ const struct qe_header *hdr;
+
+ if (!firmware) {
+ printk(KERN_ERR "qe-firmware: invalid pointer\n");
+ return -EINVAL;
+ }
+
+ hdr = &firmware->header;
+ length = be32_to_cpu(hdr->length);
+
+ /* Check the magic */
+ if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') ||
+ (hdr->magic[2] != 'F')) {
+ printk(KERN_ERR "qe-firmware: not a microcode\n");
+ return -EPERM;
+ }
+
+ /* Check the version */
+ if (hdr->version != 1) {
+ printk(KERN_ERR "qe-firmware: unsupported version\n");
+ return -EPERM;
+ }
+
+ /* Validate some of the fields */
+ if ((firmware->count < 1) || (firmware->count >= MAX_QE_RISC)) {
+ printk(KERN_ERR "qe-firmware: invalid data\n");
+ return -EINVAL;
+ }
+
+ /* Validate the length and check if there's a CRC */
+ calc_size += (firmware->count - 1) * sizeof(struct qe_microcode);
+
+ for (i = 0; i < firmware->count; i++)
+ /*
+ * For situations where the second RISC uses the same microcode
+ * as the first, the 'code_offset' and 'count' fields will be
+ * zero, so it's okay to add those.
+ */
+ calc_size += sizeof(__be32) *
+ be32_to_cpu(firmware->microcode[i].count);
+
+ /* Validate the length */
+ if (length != calc_size + sizeof(__be32)) {
+ printk(KERN_ERR "qe-firmware: invalid length\n");
+ return -EPERM;
+ }
+
+ /* Validate the CRC */
+ crc = be32_to_cpu(*(__be32 *)((void *)firmware + calc_size));
+ if (crc != crc32(0, firmware, calc_size)) {
+ printk(KERN_ERR "qe-firmware: firmware CRC is invalid\n");
+ return -EIO;
+ }
+
+ /*
+ * If the microcode calls for it, split the I-RAM.
+ */
+ if (!firmware->split)
+ setbits16(&qe_immr->cp.cercr, QE_CP_CERCR_CIR);
+
+ if (firmware->soc.model)
+ printk(KERN_INFO
+ "qe-firmware: firmware '%s' for %u V%u.%u\n",
+ firmware->id, be16_to_cpu(firmware->soc.model),
+ firmware->soc.major, firmware->soc.minor);
+ else
+ printk(KERN_INFO "qe-firmware: firmware '%s'\n",
+ firmware->id);
+
+ /*
+ * The QE only supports one microcode per RISC, so clear out all the
+ * saved microcode information and put in the new.
+ */
+ memset(&qe_firmware_info, 0, sizeof(qe_firmware_info));
+ strcpy(qe_firmware_info.id, firmware->id);
+ qe_firmware_info.extended_modes = firmware->extended_modes;
+ memcpy(qe_firmware_info.vtraps, firmware->vtraps,
+ sizeof(firmware->vtraps));
+
+ /* Loop through each microcode. */
+ for (i = 0; i < firmware->count; i++) {
+ const struct qe_microcode *ucode = &firmware->microcode[i];
+
+ /* Upload a microcode if it's present */
+ if (ucode->code_offset)
+ qe_upload_microcode(firmware, ucode);
+
+ /* Program the traps for this processor */
+ for (j = 0; j < 16; j++) {
+ u32 trap = be32_to_cpu(ucode->traps[j]);
+
+ if (trap)
+ out_be32(&qe_immr->rsp[i].tibcr[j], trap);
+ }
+
+ /* Enable traps */
+ out_be32(&qe_immr->rsp[i].eccr, be32_to_cpu(ucode->eccr));
+ }
+
+ qe_firmware_uploaded = 1;
+
+ return 0;
+}
+EXPORT_SYMBOL(qe_upload_firmware);
+
+/*
+ * Get info on the currently-loaded firmware
+ *
+ * This function also checks the device tree to see if the boot loader has
+ * uploaded a firmware already.
+ */
+struct qe_firmware_info *qe_get_firmware_info(void)
+{
+ static int initialized;
+ struct property *prop;
+ struct device_node *qe;
+ struct device_node *fw = NULL;
+ const char *sprop;
+ unsigned int i;
+
+ /*
+ * If we haven't checked yet, and a driver hasn't uploaded a firmware
+ * yet, then check the device tree for information.
+ */
+ if (initialized || qe_firmware_uploaded)
+ return NULL;
+
+ initialized = 1;
+
+ /*
+ * Newer device trees have an "fsl,qe" compatible property for the QE
+ * node, but we still need to support older device trees.
+ */
+ qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
+ if (!qe) {
+ qe = of_find_node_by_type(NULL, "qe");
+ if (!qe)
+ return NULL;
+ }
+
+ /* Find the 'firmware' child node */
+ for_each_child_of_node(qe, fw) {
+ if (strcmp(fw->name, "firmware") == 0)
+ break;
+ }
+
+ of_node_put(qe);
+
+ /* Did we find the 'firmware' node? */
+ if (!fw)
+ return NULL;
+
+ qe_firmware_uploaded = 1;
+
+ /* Copy the data into qe_firmware_info*/
+ sprop = of_get_property(fw, "id", NULL);
+ if (sprop)
+ strncpy(qe_firmware_info.id, sprop,
+ sizeof(qe_firmware_info.id) - 1);
+
+ prop = of_find_property(fw, "extended-modes", NULL);
+ if (prop && (prop->length == sizeof(u64))) {
+ const u64 *iprop = prop->value;
+
+ qe_firmware_info.extended_modes = *iprop;
+ }
+
+ prop = of_find_property(fw, "virtual-traps", NULL);
+ if (prop && (prop->length == 32)) {
+ const u32 *iprop = prop->value;
+
+ for (i = 0; i < ARRAY_SIZE(qe_firmware_info.vtraps); i++)
+ qe_firmware_info.vtraps[i] = iprop[i];
+ }
+
+ of_node_put(fw);
+
+ return &qe_firmware_info;
+}
+EXPORT_SYMBOL(qe_get_firmware_info);
+
diff --git a/arch/powerpc/sysdev/qe_lib/ucc_slow.c b/arch/powerpc/sysdev/qe_lib/ucc_slow.c
index 0174b3a..b2870b2 100644
--- a/arch/powerpc/sysdev/qe_lib/ucc_slow.c
+++ b/arch/powerpc/sysdev/qe_lib/ucc_slow.c
@@ -19,6 +19,7 @@
#include <linux/stddef.h>
#include <linux/interrupt.h>
#include <linux/err.h>
+#include <linux/module.h>
#include <asm/io.h>
#include <asm/immap_qe.h>
@@ -41,6 +42,7 @@
default: return QE_CR_SUBBLOCK_INVALID;
}
}
+EXPORT_SYMBOL(ucc_slow_get_qe_cr_subblock);
void ucc_slow_poll_transmitter_now(struct ucc_slow_private * uccs)
{
@@ -56,6 +58,7 @@
qe_issue_cmd(QE_GRACEFUL_STOP_TX, id,
QE_CR_PROTOCOL_UNSPECIFIED, 0);
}
+EXPORT_SYMBOL(ucc_slow_graceful_stop_tx);
void ucc_slow_stop_tx(struct ucc_slow_private * uccs)
{
@@ -65,6 +68,7 @@
id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num);
qe_issue_cmd(QE_STOP_TX, id, QE_CR_PROTOCOL_UNSPECIFIED, 0);
}
+EXPORT_SYMBOL(ucc_slow_stop_tx);
void ucc_slow_restart_tx(struct ucc_slow_private * uccs)
{
@@ -74,6 +78,7 @@
id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num);
qe_issue_cmd(QE_RESTART_TX, id, QE_CR_PROTOCOL_UNSPECIFIED, 0);
}
+EXPORT_SYMBOL(ucc_slow_restart_tx);
void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode)
{
@@ -94,6 +99,7 @@
}
out_be32(&us_regs->gumr_l, gumr_l);
}
+EXPORT_SYMBOL(ucc_slow_enable);
void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode)
{
@@ -114,6 +120,7 @@
}
out_be32(&us_regs->gumr_l, gumr_l);
}
+EXPORT_SYMBOL(ucc_slow_disable);
/* Initialize the UCC for Slow operations
*
@@ -347,6 +354,7 @@
*uccs_ret = uccs;
return 0;
}
+EXPORT_SYMBOL(ucc_slow_init);
void ucc_slow_free(struct ucc_slow_private * uccs)
{
@@ -366,5 +374,5 @@
kfree(uccs);
}
-
+EXPORT_SYMBOL(ucc_slow_free);
diff --git a/arch/ppc/kernel/Makefile b/arch/ppc/kernel/Makefile
index 6b4f022..5da0ca7 100644
--- a/arch/ppc/kernel/Makefile
+++ b/arch/ppc/kernel/Makefile
@@ -13,7 +13,6 @@
ppc_htab.o
obj-$(CONFIG_MODULES) += ppc_ksyms.o
obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_RAPIDIO) += rio.o
obj-$(CONFIG_KGDB) += ppc-stub.o
obj-$(CONFIG_SMP) += smp.o smp-tbsync.o
obj-$(CONFIG_KEXEC) += machine_kexec.o relocate_kernel.o
diff --git a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c
index 674806e..0706dca 100644
--- a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c
+++ b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c
@@ -42,8 +42,6 @@
#include <mm/mmu_decl.h>
-#include <syslib/ppc85xx_rio.h>
-
#include <platforms/85xx/mpc85xx_ads_common.h>
#ifndef CONFIG_PCI
@@ -190,6 +188,7 @@
#endif /* CONFIG_PCI */
#ifdef CONFIG_RAPIDIO
+extern void mpc85xx_rio_setup(int law_start, int law_size);
void platform_rio_init(void)
{
/* 512MB RIO LAW at 0xc0000000 */
diff --git a/arch/ppc/platforms/85xx/stx_gp3.c b/arch/ppc/platforms/85xx/stx_gp3.c
index 731b40e..8748da3 100644
--- a/arch/ppc/platforms/85xx/stx_gp3.c
+++ b/arch/ppc/platforms/85xx/stx_gp3.c
@@ -54,7 +54,6 @@
#include <syslib/cpm2_pic.h>
#include <syslib/ppc85xx_common.h>
-#include <syslib/ppc85xx_rio.h>
unsigned char __res[sizeof(bd_t)];
@@ -270,6 +269,7 @@
#endif /* CONFIG_PCI */
#ifdef CONFIG_RAPIDIO
+extern void mpc85xx_rio_setup(int law_start, int law_size);
void
platform_rio_init(void)
{
diff --git a/arch/ppc/platforms/85xx/tqm85xx.c b/arch/ppc/platforms/85xx/tqm85xx.c
index 4ee2bd1..2a863a8 100644
--- a/arch/ppc/platforms/85xx/tqm85xx.c
+++ b/arch/ppc/platforms/85xx/tqm85xx.c
@@ -54,7 +54,6 @@
#include <syslib/ppc85xx_setup.h>
#include <syslib/cpm2_pic.h>
#include <syslib/ppc85xx_common.h>
-#include <syslib/ppc85xx_rio.h>
#ifndef CONFIG_PCI
unsigned long isa_io_base = 0;
@@ -309,6 +308,7 @@
#endif /* CONFIG_PCI */
#ifdef CONFIG_RAPIDIO
+extern void mpc85xx_rio_setup(int law_start, int law_size);
void platform_rio_init(void)
{
/* 512MB RIO LAW at 0xc0000000 */
diff --git a/arch/ppc/syslib/Makefile b/arch/ppc/syslib/Makefile
index 543795b..5e16228 100644
--- a/arch/ppc/syslib/Makefile
+++ b/arch/ppc/syslib/Makefile
@@ -93,7 +93,6 @@
ifeq ($(CONFIG_85xx),y)
obj-$(CONFIG_PCI) += pci_auto.o
endif
-obj-$(CONFIG_RAPIDIO) += ppc85xx_rio.o
obj-$(CONFIG_83xx) += ppc83xx_setup.o ppc_sys.o \
mpc83xx_sys.o mpc83xx_devices.o ipic.o
ifeq ($(CONFIG_83xx),y)
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c
index c83bd65..42d94ed 100644
--- a/drivers/net/fs_enet/fs_enet-main.c
+++ b/drivers/net/fs_enet/fs_enet-main.c
@@ -1178,8 +1178,15 @@
struct device_node *phynode, *mdionode;
struct resource res;
int ret = 0, len;
+ const u32 *data;
- const u32 *data = of_get_property(np, "phy-handle", &len);
+ data = of_get_property(np, "fixed-link", NULL);
+ if (data) {
+ snprintf(fpi->bus_id, 16, PHY_ID_FMT, 0, *data);
+ return 0;
+ }
+
+ data = of_get_property(np, "phy-handle", &len);
if (!data || len != 4)
return -EINVAL;
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 54b2ba9..7fe03ce 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -61,34 +61,12 @@
Currently supports the IP175C PHY.
config FIXED_PHY
- tristate "Drivers for PHY emulation on fixed speed/link"
+ bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
---help---
- Adds the driver to PHY layer to cover the boards that do not have any PHY bound,
- but with the ability to manipulate the speed/link in software. The relevant MII
- speed/duplex parameters could be effectively handled in a user-specified function.
- Currently tested with mpc866ads.
+ Adds the platform "fixed" MDIO Bus to cover the boards that use
+ PHYs that are not connected to the real MDIO bus.
-config FIXED_MII_10_FDX
- bool "Emulation for 10M Fdx fixed PHY behavior"
- depends on FIXED_PHY
-
-config FIXED_MII_100_FDX
- bool "Emulation for 100M Fdx fixed PHY behavior"
- depends on FIXED_PHY
-
-config FIXED_MII_1000_FDX
- bool "Emulation for 1000M Fdx fixed PHY behavior"
- depends on FIXED_PHY
-
-config FIXED_MII_AMNT
- int "Number of emulated PHYs to allocate "
- depends on FIXED_PHY
- default "1"
- ---help---
- Sometimes it is required to have several independent emulated
- PHYs on the bus (in case of multi-eth but phy-less HW for instance).
- This control will have specified number allocated for each fixed
- PHY type enabled.
+ Currently tested with mpc866ads and mpc8349e-mitx.
config MDIO_BITBANG
tristate "Support for bitbanged MDIO buses"
diff --git a/drivers/net/phy/fixed.c b/drivers/net/phy/fixed.c
index 5619182..73b6d39 100644
--- a/drivers/net/phy/fixed.c
+++ b/drivers/net/phy/fixed.c
@@ -1,362 +1,253 @@
/*
- * drivers/net/phy/fixed.c
+ * Fixed MDIO bus (MDIO bus emulation with fixed PHYs)
*
- * Driver for fixed PHYs, when transceiver is able to operate in one fixed mode.
+ * Author: Vitaly Bordug <vbordug@ru.mvista.com>
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
*
- * Author: Vitaly Bordug
- *
- * Copyright (c) 2006 MontaVista Software, Inc.
+ * Copyright (c) 2006-2007 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
- *
*/
+
#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/unistd.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mm.h>
#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/list.h>
#include <linux/mii.h>
-#include <linux/ethtool.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
+#define MII_REGS_NUM 29
-/* we need to track the allocated pointers in order to free them on exit */
-static struct fixed_info *fixed_phy_ptrs[CONFIG_FIXED_MII_AMNT*MAX_PHY_AMNT];
+struct fixed_mdio_bus {
+ int irqs[PHY_MAX_ADDR];
+ struct mii_bus mii_bus;
+ struct list_head phys;
+};
-/*-----------------------------------------------------------------------------
- * If something weird is required to be done with link/speed,
- * network driver is able to assign a function to implement this.
- * May be useful for PHY's that need to be software-driven.
- *-----------------------------------------------------------------------------*/
-int fixed_mdio_set_link_update(struct phy_device *phydev,
- int (*link_update) (struct net_device *,
- struct fixed_phy_status *))
+struct fixed_phy {
+ int id;
+ u16 regs[MII_REGS_NUM];
+ struct phy_device *phydev;
+ struct fixed_phy_status status;
+ int (*link_update)(struct net_device *, struct fixed_phy_status *);
+ struct list_head node;
+};
+
+static struct platform_device *pdev;
+static struct fixed_mdio_bus platform_fmb = {
+ .phys = LIST_HEAD_INIT(platform_fmb.phys),
+};
+
+static int fixed_phy_update_regs(struct fixed_phy *fp)
{
- struct fixed_info *fixed;
-
- if (link_update == NULL)
- return -EINVAL;
-
- if (phydev) {
- if (phydev->bus) {
- fixed = phydev->bus->priv;
- fixed->link_update = link_update;
- return 0;
- }
- }
- return -EINVAL;
-}
-
-EXPORT_SYMBOL(fixed_mdio_set_link_update);
-
-struct fixed_info *fixed_mdio_get_phydev (int phydev_ind)
-{
- if (phydev_ind >= MAX_PHY_AMNT)
- return NULL;
- return fixed_phy_ptrs[phydev_ind];
-}
-
-EXPORT_SYMBOL(fixed_mdio_get_phydev);
-
-/*-----------------------------------------------------------------------------
- * This is used for updating internal mii regs from the status
- *-----------------------------------------------------------------------------*/
-#if defined(CONFIG_FIXED_MII_100_FDX) || defined(CONFIG_FIXED_MII_10_FDX) || defined(CONFIG_FIXED_MII_1000_FDX)
-static int fixed_mdio_update_regs(struct fixed_info *fixed)
-{
- u16 *regs = fixed->regs;
- u16 bmsr = 0;
+ u16 bmsr = BMSR_ANEGCAPABLE;
u16 bmcr = 0;
+ u16 lpagb = 0;
+ u16 lpa = 0;
- if (!regs) {
- printk(KERN_ERR "%s: regs not set up", __FUNCTION__);
- return -EINVAL;
- }
-
- if (fixed->phy_status.link)
- bmsr |= BMSR_LSTATUS;
-
- if (fixed->phy_status.duplex) {
+ if (fp->status.duplex) {
bmcr |= BMCR_FULLDPLX;
- switch (fixed->phy_status.speed) {
+ switch (fp->status.speed) {
+ case 1000:
+ bmsr |= BMSR_ESTATEN;
+ bmcr |= BMCR_SPEED1000;
+ lpagb |= LPA_1000FULL;
+ break;
case 100:
bmsr |= BMSR_100FULL;
bmcr |= BMCR_SPEED100;
+ lpa |= LPA_100FULL;
break;
-
case 10:
bmsr |= BMSR_10FULL;
+ lpa |= LPA_10FULL;
break;
+ default:
+ printk(KERN_WARNING "fixed phy: unknown speed\n");
+ return -EINVAL;
}
} else {
- switch (fixed->phy_status.speed) {
+ switch (fp->status.speed) {
+ case 1000:
+ bmsr |= BMSR_ESTATEN;
+ bmcr |= BMCR_SPEED1000;
+ lpagb |= LPA_1000HALF;
+ break;
case 100:
bmsr |= BMSR_100HALF;
bmcr |= BMCR_SPEED100;
+ lpa |= LPA_100HALF;
break;
-
case 10:
- bmsr |= BMSR_100HALF;
+ bmsr |= BMSR_10HALF;
+ lpa |= LPA_10HALF;
break;
+ default:
+ printk(KERN_WARNING "fixed phy: unknown speed\n");
+ return -EINVAL;
}
}
- regs[MII_BMCR] = bmcr;
- regs[MII_BMSR] = bmsr | 0x800; /*we are always capable of 10 hdx */
+ if (fp->status.link)
+ bmsr |= BMSR_LSTATUS | BMSR_ANEGCOMPLETE;
+
+ if (fp->status.pause)
+ lpa |= LPA_PAUSE_CAP;
+
+ if (fp->status.asym_pause)
+ lpa |= LPA_PAUSE_ASYM;
+
+ fp->regs[MII_PHYSID1] = fp->id >> 16;
+ fp->regs[MII_PHYSID2] = fp->id;
+
+ fp->regs[MII_BMSR] = bmsr;
+ fp->regs[MII_BMCR] = bmcr;
+ fp->regs[MII_LPA] = lpa;
+ fp->regs[MII_STAT1000] = lpagb;
return 0;
}
-static int fixed_mii_read(struct mii_bus *bus, int phy_id, int location)
+static int fixed_mdio_read(struct mii_bus *bus, int phy_id, int reg_num)
{
- struct fixed_info *fixed = bus->priv;
+ struct fixed_mdio_bus *fmb = container_of(bus, struct fixed_mdio_bus,
+ mii_bus);
+ struct fixed_phy *fp;
- /* if user has registered link update callback, use it */
- if (fixed->phydev)
- if (fixed->phydev->attached_dev) {
- if (fixed->link_update) {
- fixed->link_update(fixed->phydev->attached_dev,
- &fixed->phy_status);
- fixed_mdio_update_regs(fixed);
- }
- }
-
- if ((unsigned int)location >= fixed->regs_num)
+ if (reg_num >= MII_REGS_NUM)
return -1;
- return fixed->regs[location];
-}
-static int fixed_mii_write(struct mii_bus *bus, int phy_id, int location,
- u16 val)
-{
- /* do nothing for now */
- return 0;
-}
-
-static int fixed_mii_reset(struct mii_bus *bus)
-{
- /*nothing here - no way/need to reset it */
- return 0;
-}
-#endif
-
-static int fixed_config_aneg(struct phy_device *phydev)
-{
- /* :TODO:03/13/2006 09:45:37 PM::
- The full autoneg funcionality can be emulated,
- but no need to have anything here for now
- */
- return 0;
-}
-
-/*-----------------------------------------------------------------------------
- * the manual bind will do the magic - with phy_id_mask == 0
- * match will never return true...
- *-----------------------------------------------------------------------------*/
-static struct phy_driver fixed_mdio_driver = {
- .name = "Fixed PHY",
-#ifdef CONFIG_FIXED_MII_1000_FDX
- .features = PHY_GBIT_FEATURES,
-#else
- .features = PHY_BASIC_FEATURES,
-#endif
- .config_aneg = fixed_config_aneg,
- .read_status = genphy_read_status,
- .driver = { .owner = THIS_MODULE, },
-};
-
-static void fixed_mdio_release(struct device *dev)
-{
- struct phy_device *phydev = container_of(dev, struct phy_device, dev);
- struct mii_bus *bus = phydev->bus;
- struct fixed_info *fixed = bus->priv;
-
- kfree(phydev);
- kfree(bus->dev);
- kfree(bus);
- kfree(fixed->regs);
- kfree(fixed);
-}
-
-/*-----------------------------------------------------------------------------
- * This func is used to create all the necessary stuff, bind
- * the fixed phy driver and register all it on the mdio_bus_type.
- * speed is either 10 or 100 or 1000, duplex is boolean.
- * number is used to create multiple fixed PHYs, so that several devices can
- * utilize them simultaneously.
- *
- * The device on mdio bus will look like [bus_id]:[phy_id],
- * bus_id = number
- * phy_id = speed+duplex.
- *-----------------------------------------------------------------------------*/
-#if defined(CONFIG_FIXED_MII_100_FDX) || defined(CONFIG_FIXED_MII_10_FDX) || defined(CONFIG_FIXED_MII_1000_FDX)
-struct fixed_info *fixed_mdio_register_device(
- int bus_id, int speed, int duplex, u8 phy_id)
-{
- struct mii_bus *new_bus;
- struct fixed_info *fixed;
- struct phy_device *phydev;
- int err;
-
- struct device *dev = kzalloc(sizeof(struct device), GFP_KERNEL);
-
- if (dev == NULL)
- goto err_dev_alloc;
-
- new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
-
- if (new_bus == NULL)
- goto err_bus_alloc;
-
- fixed = kzalloc(sizeof(struct fixed_info), GFP_KERNEL);
-
- if (fixed == NULL)
- goto err_fixed_alloc;
-
- fixed->regs = kzalloc(MII_REGS_NUM * sizeof(int), GFP_KERNEL);
- if (NULL == fixed->regs)
- goto err_fixed_regs_alloc;
-
- fixed->regs_num = MII_REGS_NUM;
- fixed->phy_status.speed = speed;
- fixed->phy_status.duplex = duplex;
- fixed->phy_status.link = 1;
-
- new_bus->name = "Fixed MII Bus";
- new_bus->read = &fixed_mii_read;
- new_bus->write = &fixed_mii_write;
- new_bus->reset = &fixed_mii_reset;
- /*set up workspace */
- fixed_mdio_update_regs(fixed);
- new_bus->priv = fixed;
-
- new_bus->dev = dev;
- dev_set_drvdata(dev, new_bus);
-
- /* create phy_device and register it on the mdio bus */
- phydev = phy_device_create(new_bus, 0, 0);
- if (phydev == NULL)
- goto err_phy_dev_create;
-
- /*
- * Put the phydev pointer into the fixed pack so that bus read/write
- * code could be able to access for instance attached netdev. Well it
- * doesn't have to do so, only in case of utilizing user-specified
- * link-update...
- */
-
- fixed->phydev = phydev;
- phydev->speed = speed;
- phydev->duplex = duplex;
-
- phydev->irq = PHY_IGNORE_INTERRUPT;
- phydev->dev.bus = &mdio_bus_type;
-
- snprintf(phydev->dev.bus_id, BUS_ID_SIZE,
- PHY_ID_FMT, bus_id, phy_id);
-
- phydev->bus = new_bus;
-
- phydev->dev.driver = &fixed_mdio_driver.driver;
- phydev->dev.release = fixed_mdio_release;
- err = phydev->dev.driver->probe(&phydev->dev);
- if (err < 0) {
- printk(KERN_ERR "Phy %s: problems with fixed driver\n",
- phydev->dev.bus_id);
- goto err_out;
+ list_for_each_entry(fp, &fmb->phys, node) {
+ if (fp->id == phy_id) {
+ /* Issue callback if user registered it. */
+ if (fp->link_update) {
+ fp->link_update(fp->phydev->attached_dev,
+ &fp->status);
+ fixed_phy_update_regs(fp);
+ }
+ return fp->regs[reg_num];
+ }
}
- err = device_register(&phydev->dev);
- if (err) {
- printk(KERN_ERR "Phy %s failed to register\n",
- phydev->dev.bus_id);
- goto err_out;
- }
- //phydev->state = PHY_RUNNING; /* make phy go up quick, but in 10Mbit/HDX
- return fixed;
-err_out:
- kfree(phydev);
-err_phy_dev_create:
- kfree(fixed->regs);
-err_fixed_regs_alloc:
- kfree(fixed);
-err_fixed_alloc:
- kfree(new_bus);
-err_bus_alloc:
- kfree(dev);
-err_dev_alloc:
-
- return NULL;
-
+ return 0xFFFF;
}
-#endif
-MODULE_DESCRIPTION("Fixed PHY device & driver for PAL");
+static int fixed_mdio_write(struct mii_bus *bus, int phy_id, int reg_num,
+ u16 val)
+{
+ return 0;
+}
+
+/*
+ * If something weird is required to be done with link/speed,
+ * network driver is able to assign a function to implement this.
+ * May be useful for PHY's that need to be software-driven.
+ */
+int fixed_phy_set_link_update(struct phy_device *phydev,
+ int (*link_update)(struct net_device *,
+ struct fixed_phy_status *))
+{
+ struct fixed_mdio_bus *fmb = &platform_fmb;
+ struct fixed_phy *fp;
+
+ if (!link_update || !phydev || !phydev->bus)
+ return -EINVAL;
+
+ list_for_each_entry(fp, &fmb->phys, node) {
+ if (fp->id == phydev->phy_id) {
+ fp->link_update = link_update;
+ fp->phydev = phydev;
+ return 0;
+ }
+ }
+
+ return -ENOENT;
+}
+EXPORT_SYMBOL_GPL(fixed_phy_set_link_update);
+
+int fixed_phy_add(unsigned int irq, int phy_id,
+ struct fixed_phy_status *status)
+{
+ int ret;
+ struct fixed_mdio_bus *fmb = &platform_fmb;
+ struct fixed_phy *fp;
+
+ fp = kzalloc(sizeof(*fp), GFP_KERNEL);
+ if (!fp)
+ return -ENOMEM;
+
+ memset(fp->regs, 0xFF, sizeof(fp->regs[0]) * MII_REGS_NUM);
+
+ fmb->irqs[phy_id] = irq;
+
+ fp->id = phy_id;
+ fp->status = *status;
+
+ ret = fixed_phy_update_regs(fp);
+ if (ret)
+ goto err_regs;
+
+ list_add_tail(&fp->node, &fmb->phys);
+
+ return 0;
+
+err_regs:
+ kfree(fp);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(fixed_phy_add);
+
+static int __init fixed_mdio_bus_init(void)
+{
+ struct fixed_mdio_bus *fmb = &platform_fmb;
+ int ret;
+
+ pdev = platform_device_register_simple("Fixed MDIO bus", 0, NULL, 0);
+ if (!pdev) {
+ ret = -ENOMEM;
+ goto err_pdev;
+ }
+
+ fmb->mii_bus.id = 0;
+ fmb->mii_bus.name = "Fixed MDIO Bus";
+ fmb->mii_bus.dev = &pdev->dev;
+ fmb->mii_bus.read = &fixed_mdio_read;
+ fmb->mii_bus.write = &fixed_mdio_write;
+ fmb->mii_bus.irq = fmb->irqs;
+
+ ret = mdiobus_register(&fmb->mii_bus);
+ if (ret)
+ goto err_mdiobus_reg;
+
+ return 0;
+
+err_mdiobus_reg:
+ platform_device_unregister(pdev);
+err_pdev:
+ return ret;
+}
+module_init(fixed_mdio_bus_init);
+
+static void __exit fixed_mdio_bus_exit(void)
+{
+ struct fixed_mdio_bus *fmb = &platform_fmb;
+ struct fixed_phy *fp;
+
+ mdiobus_unregister(&fmb->mii_bus);
+ platform_device_unregister(pdev);
+
+ list_for_each_entry(fp, &fmb->phys, node) {
+ list_del(&fp->node);
+ kfree(fp);
+ }
+}
+module_exit(fixed_mdio_bus_exit);
+
+MODULE_DESCRIPTION("Fixed MDIO bus (MDIO bus emulation with fixed PHYs)");
MODULE_AUTHOR("Vitaly Bordug");
MODULE_LICENSE("GPL");
-
-static int __init fixed_init(void)
-{
- int cnt = 0;
- int i;
-/* register on the bus... Not expected to be matched
- * with anything there...
- *
- */
- phy_driver_register(&fixed_mdio_driver);
-
-/* We will create several mdio devices here, and will bound the upper
- * driver to them.
- *
- * Then the external software can lookup the phy bus by searching
- * for 0:101, to be connected to the virtual 100M Fdx phy.
- *
- * In case several virtual PHYs required, the bus_id will be in form
- * [num]:[duplex]+[speed], which make it able even to define
- * driver-specific link control callback, if for instance PHY is
- * completely SW-driven.
- */
- for (i=1; i <= CONFIG_FIXED_MII_AMNT; i++) {
-#ifdef CONFIG_FIXED_MII_1000_FDX
- fixed_phy_ptrs[cnt++] = fixed_mdio_register_device(0, 1000, 1, i);
-#endif
-#ifdef CONFIG_FIXED_MII_100_FDX
- fixed_phy_ptrs[cnt++] = fixed_mdio_register_device(1, 100, 1, i);
-#endif
-#ifdef CONFIG_FIXED_MII_10_FDX
- fixed_phy_ptrs[cnt++] = fixed_mdio_register_device(2, 10, 1, i);
-#endif
- }
-
- return 0;
-}
-
-static void __exit fixed_exit(void)
-{
- int i;
-
- phy_driver_unregister(&fixed_mdio_driver);
- for (i=0; i < MAX_PHY_AMNT; i++)
- if ( fixed_phy_ptrs[i] )
- device_unregister(&fixed_phy_ptrs[i]->phydev->dev);
-}
-
-module_init(fixed_init);
-module_exit(fixed_exit);
diff --git a/drivers/rapidio/rio.c b/drivers/rapidio/rio.c
index f644807..80c5f1b 100644
--- a/drivers/rapidio/rio.c
+++ b/drivers/rapidio/rio.c
@@ -23,6 +23,7 @@
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/slab.h>
+#include <linux/interrupt.h>
#include "rio.h"
@@ -476,8 +477,8 @@
port->iores.end - port->iores.start,
port->name)) {
printk(KERN_ERR
- "RIO: Error requesting master port region %8.8lx-%8.8lx\n",
- port->iores.start, port->iores.end - 1);
+ "RIO: Error requesting master port region 0x%016llx-0x%016llx\n",
+ (u64)port->iores.start, (u64)port->iores.end - 1);
rc = -ENOMEM;
goto out;
}
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index d7e1996..d962b74 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1284,4 +1284,14 @@
Currently, only 8250 compatible ports are supported, but
others can easily be added.
+config SERIAL_QE
+ tristate "Freescale QUICC Engine serial port support"
+ depends on QUICC_ENGINE
+ select SERIAL_CORE
+ select FW_LOADER
+ default n
+ help
+ This driver supports the QE serial ports on Freescale embedded
+ PowerPC that contain a QUICC Engine.
+
endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index af6377d..7eb4553 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -64,3 +64,4 @@
obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
+obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
index def0158..d9af06a 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
@@ -165,9 +165,9 @@
* really has to get out of the driver so boards can
* be supported in a sane fashion.
*/
+ volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
#ifndef CONFIG_STX_GP3
volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
io->iop_pparb |= 0x008b0000;
io->iop_pdirb |= 0x00880000;
diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c
new file mode 100644
index 0000000..e0994f0
--- /dev/null
+++ b/drivers/serial/ucc_uart.c
@@ -0,0 +1,1514 @@
+/*
+ * Freescale QUICC Engine UART device driver
+ *
+ * Author: Timur Tabi <timur@freescale.com>
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * This driver adds support for UART devices via Freescale's QUICC Engine
+ * found on some Freescale SOCs.
+ *
+ * If Soft-UART support is needed but not already present, then this driver
+ * will request and upload the "Soft-UART" microcode upon probe. The
+ * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X"
+ * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC,
+ * (e.g. "11" for 1.1).
+ */
+
+#include <linux/module.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/io.h>
+#include <linux/of_platform.h>
+#include <linux/dma-mapping.h>
+
+#include <linux/fs_uart_pd.h>
+#include <asm/ucc_slow.h>
+
+#include <linux/firmware.h>
+#include <asm/reg.h>
+
+/*
+ * The GUMR flag for Soft UART. This would normally be defined in qe.h,
+ * but Soft-UART is a hack and we want to keep everything related to it in
+ * this file.
+ */
+#define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */
+
+/*
+ * soft_uart is 1 if we need to use Soft-UART mode
+ */
+static int soft_uart;
+/*
+ * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise.
+ */
+static int firmware_loaded;
+
+/* Enable this macro to configure all serial ports in internal loopback
+ mode */
+/* #define LOOPBACK */
+
+/* The major and minor device numbers are defined in
+ * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE
+ * UART, we have major number 204 and minor numbers 46 - 49, which are the
+ * same as for the CPM2. This decision was made because no Freescale part
+ * has both a CPM and a QE.
+ */
+#define SERIAL_QE_MAJOR 204
+#define SERIAL_QE_MINOR 46
+
+/* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */
+#define UCC_MAX_UART 4
+
+/* The number of buffer descriptors for receiving characters. */
+#define RX_NUM_FIFO 4
+
+/* The number of buffer descriptors for transmitting characters. */
+#define TX_NUM_FIFO 4
+
+/* The maximum size of the character buffer for a single RX BD. */
+#define RX_BUF_SIZE 32
+
+/* The maximum size of the character buffer for a single TX BD. */
+#define TX_BUF_SIZE 32
+
+/*
+ * The number of jiffies to wait after receiving a close command before the
+ * device is actually closed. This allows the last few characters to be
+ * sent over the wire.
+ */
+#define UCC_WAIT_CLOSING 100
+
+struct ucc_uart_pram {
+ struct ucc_slow_pram common;
+ u8 res1[8]; /* reserved */
+ __be16 maxidl; /* Maximum idle chars */
+ __be16 idlc; /* temp idle counter */
+ __be16 brkcr; /* Break count register */
+ __be16 parec; /* receive parity error counter */
+ __be16 frmec; /* receive framing error counter */
+ __be16 nosec; /* receive noise counter */
+ __be16 brkec; /* receive break condition counter */
+ __be16 brkln; /* last received break length */
+ __be16 uaddr[2]; /* UART address character 1 & 2 */
+ __be16 rtemp; /* Temp storage */
+ __be16 toseq; /* Transmit out of sequence char */
+ __be16 cchars[8]; /* control characters 1-8 */
+ __be16 rccm; /* receive control character mask */
+ __be16 rccr; /* receive control character register */
+ __be16 rlbc; /* receive last break character */
+ __be16 res2; /* reserved */
+ __be32 res3; /* reserved, should be cleared */
+ u8 res4; /* reserved, should be cleared */
+ u8 res5[3]; /* reserved, should be cleared */
+ __be32 res6; /* reserved, should be cleared */
+ __be32 res7; /* reserved, should be cleared */
+ __be32 res8; /* reserved, should be cleared */
+ __be32 res9; /* reserved, should be cleared */
+ __be32 res10; /* reserved, should be cleared */
+ __be32 res11; /* reserved, should be cleared */
+ __be32 res12; /* reserved, should be cleared */
+ __be32 res13; /* reserved, should be cleared */
+/* The rest is for Soft-UART only */
+ __be16 supsmr; /* 0x90, Shadow UPSMR */
+ __be16 res92; /* 0x92, reserved, initialize to 0 */
+ __be32 rx_state; /* 0x94, RX state, initialize to 0 */
+ __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */
+ u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */
+ u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */
+ u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */
+ u8 res14[0xBC - 0x9F]; /* reserved */
+ __be32 dump_ptr; /* 0xBC, Dump pointer */
+ __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */
+ u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */
+ u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */
+ __be16 tx_state; /* 0xC6, TX state */
+ u8 res15[0xD0 - 0xC8]; /* reserved */
+ __be32 resD0; /* 0xD0, reserved, initialize to 0 */
+ u8 resD4; /* 0xD4, reserved, initialize to 0 */
+ __be16 resD5; /* 0xD5, reserved, initialize to 0 */
+} __attribute__ ((packed));
+
+/* SUPSMR definitions, for Soft-UART only */
+#define UCC_UART_SUPSMR_SL 0x8000
+#define UCC_UART_SUPSMR_RPM_MASK 0x6000
+#define UCC_UART_SUPSMR_RPM_ODD 0x0000
+#define UCC_UART_SUPSMR_RPM_LOW 0x2000
+#define UCC_UART_SUPSMR_RPM_EVEN 0x4000
+#define UCC_UART_SUPSMR_RPM_HIGH 0x6000
+#define UCC_UART_SUPSMR_PEN 0x1000
+#define UCC_UART_SUPSMR_TPM_MASK 0x0C00
+#define UCC_UART_SUPSMR_TPM_ODD 0x0000
+#define UCC_UART_SUPSMR_TPM_LOW 0x0400
+#define UCC_UART_SUPSMR_TPM_EVEN 0x0800
+#define UCC_UART_SUPSMR_TPM_HIGH 0x0C00
+#define UCC_UART_SUPSMR_FRZ 0x0100
+#define UCC_UART_SUPSMR_UM_MASK 0x00c0
+#define UCC_UART_SUPSMR_UM_NORMAL 0x0000
+#define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040
+#define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0
+#define UCC_UART_SUPSMR_CL_MASK 0x0030
+#define UCC_UART_SUPSMR_CL_8 0x0030
+#define UCC_UART_SUPSMR_CL_7 0x0020
+#define UCC_UART_SUPSMR_CL_6 0x0010
+#define UCC_UART_SUPSMR_CL_5 0x0000
+
+#define UCC_UART_TX_STATE_AHDLC 0x00
+#define UCC_UART_TX_STATE_UART 0x01
+#define UCC_UART_TX_STATE_X1 0x00
+#define UCC_UART_TX_STATE_X16 0x80
+
+#define UCC_UART_PRAM_ALIGNMENT 0x100
+
+#define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD
+#define NUM_CONTROL_CHARS 8
+
+/* Private per-port data structure */
+struct uart_qe_port {
+ struct uart_port port;
+ struct ucc_slow __iomem *uccp;
+ struct ucc_uart_pram __iomem *uccup;
+ struct ucc_slow_info us_info;
+ struct ucc_slow_private *us_private;
+ struct device_node *np;
+ unsigned int ucc_num; /* First ucc is 0, not 1 */
+
+ u16 rx_nrfifos;
+ u16 rx_fifosize;
+ u16 tx_nrfifos;
+ u16 tx_fifosize;
+ int wait_closing;
+ u32 flags;
+ struct qe_bd *rx_bd_base;
+ struct qe_bd *rx_cur;
+ struct qe_bd *tx_bd_base;
+ struct qe_bd *tx_cur;
+ unsigned char *tx_buf;
+ unsigned char *rx_buf;
+ void *bd_virt; /* virtual address of the BD buffers */
+ dma_addr_t bd_dma_addr; /* bus address of the BD buffers */
+ unsigned int bd_size; /* size of BD buffer space */
+};
+
+static struct uart_driver ucc_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "serial",
+ .dev_name = "ttyQE",
+ .major = SERIAL_QE_MAJOR,
+ .minor = SERIAL_QE_MINOR,
+ .nr = UCC_MAX_UART,
+};
+
+/*
+ * Virtual to physical address translation.
+ *
+ * Given the virtual address for a character buffer, this function returns
+ * the physical (DMA) equivalent.
+ */
+static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port)
+{
+ if (likely((addr >= qe_port->bd_virt)) &&
+ (addr < (qe_port->bd_virt + qe_port->bd_size)))
+ return qe_port->bd_dma_addr + (addr - qe_port->bd_virt);
+
+ /* something nasty happened */
+ printk(KERN_ERR "%s: addr=%p\n", __FUNCTION__, addr);
+ BUG();
+ return 0;
+}
+
+/*
+ * Physical to virtual address translation.
+ *
+ * Given the physical (DMA) address for a character buffer, this function
+ * returns the virtual equivalent.
+ */
+static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port)
+{
+ /* sanity check */
+ if (likely((addr >= qe_port->bd_dma_addr) &&
+ (addr < (qe_port->bd_dma_addr + qe_port->bd_size))))
+ return qe_port->bd_virt + (addr - qe_port->bd_dma_addr);
+
+ /* something nasty happened */
+ printk(KERN_ERR "%s: addr=%x\n", __FUNCTION__, addr);
+ BUG();
+ return NULL;
+}
+
+/*
+ * Return 1 if the QE is done transmitting all buffers for this port
+ *
+ * This function scans each BD in sequence. If we find a BD that is not
+ * ready (READY=1), then we return 0 indicating that the QE is still sending
+ * data. If we reach the last BD (WRAP=1), then we know we've scanned
+ * the entire list, and all BDs are done.
+ */
+static unsigned int qe_uart_tx_empty(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ struct qe_bd *bdp = qe_port->tx_bd_base;
+
+ while (1) {
+ if (in_be16(&bdp->status) & BD_SC_READY)
+ /* This BD is not done, so return "not done" */
+ return 0;
+
+ if (in_be16(&bdp->status) & BD_SC_WRAP)
+ /*
+ * This BD is done and it's the last one, so return
+ * "done"
+ */
+ return 1;
+
+ bdp++;
+ };
+}
+
+/*
+ * Set the modem control lines
+ *
+ * Although the QE can control the modem control lines (e.g. CTS), we
+ * don't need that support. This function must exist, however, otherwise
+ * the kernel will panic.
+ */
+void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+/*
+ * Get the current modem control line status
+ *
+ * Although the QE can control the modem control lines (e.g. CTS), this
+ * driver currently doesn't support that, so we always return Carrier
+ * Detect, Data Set Ready, and Clear To Send.
+ */
+static unsigned int qe_uart_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+}
+
+/*
+ * Disable the transmit interrupt.
+ *
+ * Although this function is called "stop_tx", it does not actually stop
+ * transmission of data. Instead, it tells the QE to not generate an
+ * interrupt when the UCC is finished sending characters.
+ */
+static void qe_uart_stop_tx(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+
+ clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+}
+
+/*
+ * Transmit as many characters to the HW as possible.
+ *
+ * This function will attempt to stuff of all the characters from the
+ * kernel's transmit buffer into TX BDs.
+ *
+ * A return value of non-zero indicates that it sucessfully stuffed all
+ * characters from the kernel buffer.
+ *
+ * A return value of zero indicates that there are still characters in the
+ * kernel's buffer that have not been transmitted, but there are no more BDs
+ * available. This function should be called again after a BD has been made
+ * available.
+ */
+static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
+{
+ struct qe_bd *bdp;
+ unsigned char *p;
+ unsigned int count;
+ struct uart_port *port = &qe_port->port;
+ struct circ_buf *xmit = &port->info->xmit;
+
+ bdp = qe_port->rx_cur;
+
+ /* Handle xon/xoff */
+ if (port->x_char) {
+ /* Pick next descriptor and fill from buffer */
+ bdp = qe_port->tx_cur;
+
+ p = qe2cpu_addr(bdp->buf, qe_port);
+
+ *p++ = port->x_char;
+ out_be16(&bdp->length, 1);
+ setbits16(&bdp->status, BD_SC_READY);
+ /* Get next BD. */
+ if (in_be16(&bdp->status) & BD_SC_WRAP)
+ bdp = qe_port->tx_bd_base;
+ else
+ bdp++;
+ qe_port->tx_cur = bdp;
+
+ port->icount.tx++;
+ port->x_char = 0;
+ return 1;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ qe_uart_stop_tx(port);
+ return 0;
+ }
+
+ /* Pick next descriptor and fill from buffer */
+ bdp = qe_port->tx_cur;
+
+ while (!(in_be16(&bdp->status) & BD_SC_READY) &&
+ (xmit->tail != xmit->head)) {
+ count = 0;
+ p = qe2cpu_addr(bdp->buf, qe_port);
+ while (count < qe_port->tx_fifosize) {
+ *p++ = xmit->buf[xmit->tail];
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ count++;
+ if (xmit->head == xmit->tail)
+ break;
+ }
+
+ out_be16(&bdp->length, count);
+ setbits16(&bdp->status, BD_SC_READY);
+
+ /* Get next BD. */
+ if (in_be16(&bdp->status) & BD_SC_WRAP)
+ bdp = qe_port->tx_bd_base;
+ else
+ bdp++;
+ }
+ qe_port->tx_cur = bdp;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit)) {
+ /* The kernel buffer is empty, so turn off TX interrupts. We
+ don't need to be told when the QE is finished transmitting
+ the data. */
+ qe_uart_stop_tx(port);
+ return 0;
+ }
+
+ return 1;
+}
+
+/*
+ * Start transmitting data
+ *
+ * This function will start transmitting any available data, if the port
+ * isn't already transmitting data.
+ */
+static void qe_uart_start_tx(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+
+ /* If we currently are transmitting, then just return */
+ if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
+ return;
+
+ /* Otherwise, pump the port and start transmission */
+ if (qe_uart_tx_pump(qe_port))
+ setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+}
+
+/*
+ * Stop transmitting data
+ */
+static void qe_uart_stop_rx(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+
+ clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+}
+
+/*
+ * Enable status change interrupts
+ *
+ * We don't support status change interrupts, but we need to define this
+ * function otherwise the kernel will panic.
+ */
+static void qe_uart_enable_ms(struct uart_port *port)
+{
+}
+
+/* Start or stop sending break signal
+ *
+ * This function controls the sending of a break signal. If break_state=1,
+ * then we start sending a break signal. If break_state=0, then we stop
+ * sending the break signal.
+ */
+static void qe_uart_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+
+ if (break_state)
+ ucc_slow_stop_tx(qe_port->us_private);
+ else
+ ucc_slow_restart_tx(qe_port->us_private);
+}
+
+/* ISR helper function for receiving character.
+ *
+ * This function is called by the ISR to handling receiving characters
+ */
+static void qe_uart_int_rx(struct uart_qe_port *qe_port)
+{
+ int i;
+ unsigned char ch, *cp;
+ struct uart_port *port = &qe_port->port;
+ struct tty_struct *tty = port->info->tty;
+ struct qe_bd *bdp;
+ u16 status;
+ unsigned int flg;
+
+ /* Just loop through the closed BDs and copy the characters into
+ * the buffer.
+ */
+ bdp = qe_port->rx_cur;
+ while (1) {
+ status = in_be16(&bdp->status);
+
+ /* If this one is empty, then we assume we've read them all */
+ if (status & BD_SC_EMPTY)
+ break;
+
+ /* get number of characters, and check space in RX buffer */
+ i = in_be16(&bdp->length);
+
+ /* If we don't have enough room in RX buffer for the entire BD,
+ * then we try later, which will be the next RX interrupt.
+ */
+ if (tty_buffer_request_room(tty, i) < i) {
+ dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n");
+ return;
+ }
+
+ /* get pointer */
+ cp = qe2cpu_addr(bdp->buf, qe_port);
+
+ /* loop through the buffer */
+ while (i-- > 0) {
+ ch = *cp++;
+ port->icount.rx++;
+ flg = TTY_NORMAL;
+
+ if (!i && status &
+ (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV))
+ goto handle_error;
+ if (uart_handle_sysrq_char(port, ch))
+ continue;
+
+error_return:
+ tty_insert_flip_char(tty, ch, flg);
+
+ }
+
+ /* This BD is ready to be used again. Clear status. get next */
+ clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR |
+ BD_SC_OV | BD_SC_ID, BD_SC_EMPTY);
+ if (in_be16(&bdp->status) & BD_SC_WRAP)
+ bdp = qe_port->rx_bd_base;
+ else
+ bdp++;
+
+ }
+
+ /* Write back buffer pointer */
+ qe_port->rx_cur = bdp;
+
+ /* Activate BH processing */
+ tty_flip_buffer_push(tty);
+
+ return;
+
+ /* Error processing */
+
+handle_error:
+ /* Statistics */
+ if (status & BD_SC_BR)
+ port->icount.brk++;
+ if (status & BD_SC_PR)
+ port->icount.parity++;
+ if (status & BD_SC_FR)
+ port->icount.frame++;
+ if (status & BD_SC_OV)
+ port->icount.overrun++;
+
+ /* Mask out ignored conditions */
+ status &= port->read_status_mask;
+
+ /* Handle the remaining ones */
+ if (status & BD_SC_BR)
+ flg = TTY_BREAK;
+ else if (status & BD_SC_PR)
+ flg = TTY_PARITY;
+ else if (status & BD_SC_FR)
+ flg = TTY_FRAME;
+
+ /* Overrun does not affect the current character ! */
+ if (status & BD_SC_OV)
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+#ifdef SUPPORT_SYSRQ
+ port->sysrq = 0;
+#endif
+ goto error_return;
+}
+
+/* Interrupt handler
+ *
+ * This interrupt handler is called after a BD is processed.
+ */
+static irqreturn_t qe_uart_int(int irq, void *data)
+{
+ struct uart_qe_port *qe_port = (struct uart_qe_port *) data;
+ struct ucc_slow __iomem *uccp = qe_port->uccp;
+ u16 events;
+
+ /* Clear the interrupts */
+ events = in_be16(&uccp->ucce);
+ out_be16(&uccp->ucce, events);
+
+ if (events & UCC_UART_UCCE_BRKE)
+ uart_handle_break(&qe_port->port);
+
+ if (events & UCC_UART_UCCE_RX)
+ qe_uart_int_rx(qe_port);
+
+ if (events & UCC_UART_UCCE_TX)
+ qe_uart_tx_pump(qe_port);
+
+ return events ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/* Initialize buffer descriptors
+ *
+ * This function initializes all of the RX and TX buffer descriptors.
+ */
+static void qe_uart_initbd(struct uart_qe_port *qe_port)
+{
+ int i;
+ void *bd_virt;
+ struct qe_bd *bdp;
+
+ /* Set the physical address of the host memory buffers in the buffer
+ * descriptors, and the virtual address for us to work with.
+ */
+ bd_virt = qe_port->bd_virt;
+ bdp = qe_port->rx_bd_base;
+ qe_port->rx_cur = qe_port->rx_bd_base;
+ for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) {
+ out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT);
+ out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
+ out_be16(&bdp->length, 0);
+ bd_virt += qe_port->rx_fifosize;
+ bdp++;
+ }
+
+ /* */
+ out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
+ out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
+ out_be16(&bdp->length, 0);
+
+ /* Set the physical address of the host memory
+ * buffers in the buffer descriptors, and the
+ * virtual address for us to work with.
+ */
+ bd_virt = qe_port->bd_virt +
+ L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
+ qe_port->tx_cur = qe_port->tx_bd_base;
+ bdp = qe_port->tx_bd_base;
+ for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) {
+ out_be16(&bdp->status, BD_SC_INTRPT);
+ out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
+ out_be16(&bdp->length, 0);
+ bd_virt += qe_port->tx_fifosize;
+ bdp++;
+ }
+
+ /* Loopback requires the preamble bit to be set on the first TX BD */
+#ifdef LOOPBACK
+ setbits16(&qe_port->tx_cur->status, BD_SC_P);
+#endif
+
+ out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT);
+ out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
+ out_be16(&bdp->length, 0);
+}
+
+/*
+ * Initialize a UCC for UART.
+ *
+ * This function configures a given UCC to be used as a UART device. Basic
+ * UCC initialization is handled in qe_uart_request_port(). This function
+ * does all the UART-specific stuff.
+ */
+static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
+{
+ u32 cecr_subblock;
+ struct ucc_slow __iomem *uccp = qe_port->uccp;
+ struct ucc_uart_pram *uccup = qe_port->uccup;
+
+ unsigned int i;
+
+ /* First, disable TX and RX in the UCC */
+ ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
+
+ /* Program the UCC UART parameter RAM */
+ out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
+ out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
+ out_be16(&uccup->common.mrblr, qe_port->rx_fifosize);
+ out_be16(&uccup->maxidl, 0x10);
+ out_be16(&uccup->brkcr, 1);
+ out_be16(&uccup->parec, 0);
+ out_be16(&uccup->frmec, 0);
+ out_be16(&uccup->nosec, 0);
+ out_be16(&uccup->brkec, 0);
+ out_be16(&uccup->uaddr[0], 0);
+ out_be16(&uccup->uaddr[1], 0);
+ out_be16(&uccup->toseq, 0);
+ for (i = 0; i < 8; i++)
+ out_be16(&uccup->cchars[i], 0xC000);
+ out_be16(&uccup->rccm, 0xc0ff);
+
+ /* Configure the GUMR registers for UART */
+ if (soft_uart)
+ /* Soft-UART requires a 1X multiplier for TX */
+ clrsetbits_be32(&uccp->gumr_l,
+ UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
+ UCC_SLOW_GUMR_L_RDCR_MASK,
+ UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
+ UCC_SLOW_GUMR_L_RDCR_16);
+ else
+ clrsetbits_be32(&uccp->gumr_l,
+ UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
+ UCC_SLOW_GUMR_L_RDCR_MASK,
+ UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
+ UCC_SLOW_GUMR_L_RDCR_16);
+
+ clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
+ UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
+
+#ifdef LOOPBACK
+ clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+ UCC_SLOW_GUMR_L_DIAG_LOOP);
+ clrsetbits_be32(&uccp->gumr_h,
+ UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
+ UCC_SLOW_GUMR_H_CDS);
+#endif
+
+ /* Enable rx interrupts and clear all pending events. */
+ out_be16(&uccp->uccm, 0);
+ out_be16(&uccp->ucce, 0xffff);
+ out_be16(&uccp->udsr, 0x7e7e);
+
+ /* Initialize UPSMR */
+ out_be16(&uccp->upsmr, 0);
+
+ if (soft_uart) {
+ out_be16(&uccup->supsmr, 0x30);
+ out_be16(&uccup->res92, 0);
+ out_be32(&uccup->rx_state, 0);
+ out_be32(&uccup->rx_cnt, 0);
+ out_8(&uccup->rx_bitmark, 0);
+ out_8(&uccup->rx_length, 10);
+ out_be32(&uccup->dump_ptr, 0x4000);
+ out_8(&uccup->rx_temp_dlst_qe, 0);
+ out_be32(&uccup->rx_frame_rem, 0);
+ out_8(&uccup->rx_frame_rem_size, 0);
+ /* Soft-UART requires TX to be 1X */
+ out_8(&uccup->tx_mode,
+ UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1);
+ out_be16(&uccup->tx_state, 0);
+ out_8(&uccup->resD4, 0);
+ out_be16(&uccup->resD5, 0);
+
+ /* Set UART mode.
+ * Enable receive and transmit.
+ */
+
+ /* From the microcode errata:
+ * 1.GUMR_L register, set mode=0010 (QMC).
+ * 2.Set GUMR_H[17] bit. (UART/AHDLC mode).
+ * 3.Set GUMR_H[19:20] (Transparent mode)
+ * 4.Clear GUMR_H[26] (RFW)
+ * ...
+ * 6.Receiver must use 16x over sampling
+ */
+ clrsetbits_be32(&uccp->gumr_l,
+ UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
+ UCC_SLOW_GUMR_L_RDCR_MASK,
+ UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 |
+ UCC_SLOW_GUMR_L_RDCR_16);
+
+ clrsetbits_be32(&uccp->gumr_h,
+ UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
+ UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX |
+ UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
+
+#ifdef LOOPBACK
+ clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+ UCC_SLOW_GUMR_L_DIAG_LOOP);
+ clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP |
+ UCC_SLOW_GUMR_H_CDS);
+#endif
+
+ cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
+ qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
+ QE_CR_PROTOCOL_UNSPECIFIED, 0);
+ }
+}
+
+/*
+ * Initialize the port.
+ */
+static int qe_uart_startup(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ int ret;
+
+ /*
+ * If we're using Soft-UART mode, then we need to make sure the
+ * firmware has been uploaded first.
+ */
+ if (soft_uart && !firmware_loaded) {
+ dev_err(port->dev, "Soft-UART firmware not uploaded\n");
+ return -ENODEV;
+ }
+
+ qe_uart_initbd(qe_port);
+ qe_uart_init_ucc(qe_port);
+
+ /* Install interrupt handler. */
+ ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart",
+ qe_port);
+ if (ret) {
+ dev_err(port->dev, "could not claim IRQ %u\n", port->irq);
+ return ret;
+ }
+
+ /* Startup rx-int */
+ setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+ ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX);
+
+ return 0;
+}
+
+/*
+ * Shutdown the port.
+ */
+static void qe_uart_shutdown(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ struct ucc_slow __iomem *uccp = qe_port->uccp;
+ unsigned int timeout = 20;
+
+ /* Disable RX and TX */
+
+ /* Wait for all the BDs marked sent */
+ while (!qe_uart_tx_empty(port)) {
+ if (!--timeout) {
+ dev_warn(port->dev, "shutdown timeout\n");
+ break;
+ }
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(2);
+ }
+
+ if (qe_port->wait_closing) {
+ /* Wait a bit longer */
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(qe_port->wait_closing);
+ }
+
+ /* Stop uarts */
+ ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
+ clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
+
+ /* Shut them really down and reinit buffer descriptors */
+ ucc_slow_graceful_stop_tx(qe_port->us_private);
+ qe_uart_initbd(qe_port);
+
+ free_irq(port->irq, qe_port);
+}
+
+/*
+ * Set the serial port parameters.
+ */
+static void qe_uart_set_termios(struct uart_port *port,
+ struct ktermios *termios, struct ktermios *old)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ struct ucc_slow __iomem *uccp = qe_port->uccp;
+ unsigned int baud;
+ unsigned long flags;
+ u16 upsmr = in_be16(&uccp->upsmr);
+ struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
+ u16 supsmr = in_be16(&uccup->supsmr);
+ u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
+
+ /* Character length programmed into the mode register is the
+ * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
+ * 1 or 2 stop bits, minus 1.
+ * The value 'bits' counts this for us.
+ */
+
+ /* byte size */
+ upsmr &= UCC_UART_UPSMR_CL_MASK;
+ supsmr &= UCC_UART_SUPSMR_CL_MASK;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ upsmr |= UCC_UART_UPSMR_CL_5;
+ supsmr |= UCC_UART_SUPSMR_CL_5;
+ char_length += 5;
+ break;
+ case CS6:
+ upsmr |= UCC_UART_UPSMR_CL_6;
+ supsmr |= UCC_UART_SUPSMR_CL_6;
+ char_length += 6;
+ break;
+ case CS7:
+ upsmr |= UCC_UART_UPSMR_CL_7;
+ supsmr |= UCC_UART_SUPSMR_CL_7;
+ char_length += 7;
+ break;
+ default: /* case CS8 */
+ upsmr |= UCC_UART_UPSMR_CL_8;
+ supsmr |= UCC_UART_SUPSMR_CL_8;
+ char_length += 8;
+ break;
+ }
+
+ /* If CSTOPB is set, we want two stop bits */
+ if (termios->c_cflag & CSTOPB) {
+ upsmr |= UCC_UART_UPSMR_SL;
+ supsmr |= UCC_UART_SUPSMR_SL;
+ char_length++; /* + SL */
+ }
+
+ if (termios->c_cflag & PARENB) {
+ upsmr |= UCC_UART_UPSMR_PEN;
+ supsmr |= UCC_UART_SUPSMR_PEN;
+ char_length++; /* + PEN */
+
+ if (!(termios->c_cflag & PARODD)) {
+ upsmr &= ~(UCC_UART_UPSMR_RPM_MASK |
+ UCC_UART_UPSMR_TPM_MASK);
+ upsmr |= UCC_UART_UPSMR_RPM_EVEN |
+ UCC_UART_UPSMR_TPM_EVEN;
+ supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK |
+ UCC_UART_SUPSMR_TPM_MASK);
+ supsmr |= UCC_UART_SUPSMR_RPM_EVEN |
+ UCC_UART_SUPSMR_TPM_EVEN;
+ }
+ }
+
+ /*
+ * Set up parity check flag
+ */
+ port->read_status_mask = BD_SC_EMPTY | BD_SC_OV;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= BD_SC_FR | BD_SC_PR;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= BD_SC_BR;
+
+ /*
+ * Characters to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= BD_SC_BR;
+ /*
+ * If we're ignore parity and break indicators, ignore
+ * overruns too. (For real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= BD_SC_OV;
+ }
+ /*
+ * !!! ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->read_status_mask &= ~BD_SC_EMPTY;
+
+ baud = uart_get_baud_rate(port, termios, old, 0, 115200);
+
+ /* Do we really need a spinlock here? */
+ spin_lock_irqsave(&port->lock, flags);
+
+ out_be16(&uccp->upsmr, upsmr);
+ if (soft_uart) {
+ out_be16(&uccup->supsmr, supsmr);
+ out_8(&uccup->rx_length, char_length);
+
+ /* Soft-UART requires a 1X multiplier for TX */
+ qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
+ qe_setbrg(qe_port->us_info.tx_clock, baud, 1);
+ } else {
+ qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
+ qe_setbrg(qe_port->us_info.tx_clock, baud, 16);
+ }
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * Return a pointer to a string that describes what kind of port this is.
+ */
+static const char *qe_uart_type(struct uart_port *port)
+{
+ return "QE";
+}
+
+/*
+ * Allocate any memory and I/O resources required by the port.
+ */
+static int qe_uart_request_port(struct uart_port *port)
+{
+ int ret;
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ struct ucc_slow_info *us_info = &qe_port->us_info;
+ struct ucc_slow_private *uccs;
+ unsigned int rx_size, tx_size;
+ void *bd_virt;
+ dma_addr_t bd_dma_addr = 0;
+
+ ret = ucc_slow_init(us_info, &uccs);
+ if (ret) {
+ dev_err(port->dev, "could not initialize UCC%u\n",
+ qe_port->ucc_num);
+ return ret;
+ }
+
+ qe_port->us_private = uccs;
+ qe_port->uccp = uccs->us_regs;
+ qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram;
+ qe_port->rx_bd_base = uccs->rx_bd;
+ qe_port->tx_bd_base = uccs->tx_bd;
+
+ /*
+ * Allocate the transmit and receive data buffers.
+ */
+
+ rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
+ tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize);
+
+ bd_virt = dma_alloc_coherent(NULL, rx_size + tx_size, &bd_dma_addr,
+ GFP_KERNEL);
+ if (!bd_virt) {
+ dev_err(port->dev, "could not allocate buffer descriptors\n");
+ return -ENOMEM;
+ }
+
+ qe_port->bd_virt = bd_virt;
+ qe_port->bd_dma_addr = bd_dma_addr;
+ qe_port->bd_size = rx_size + tx_size;
+
+ qe_port->rx_buf = bd_virt;
+ qe_port->tx_buf = qe_port->rx_buf + rx_size;
+
+ return 0;
+}
+
+/*
+ * Configure the port.
+ *
+ * We say we're a CPM-type port because that's mostly true. Once the device
+ * is configured, this driver operates almost identically to the CPM serial
+ * driver.
+ */
+static void qe_uart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_CPM;
+ qe_uart_request_port(port);
+ }
+}
+
+/*
+ * Release any memory and I/O resources that were allocated in
+ * qe_uart_request_port().
+ */
+static void qe_uart_release_port(struct uart_port *port)
+{
+ struct uart_qe_port *qe_port =
+ container_of(port, struct uart_qe_port, port);
+ struct ucc_slow_private *uccs = qe_port->us_private;
+
+ dma_free_coherent(NULL, qe_port->bd_size, qe_port->bd_virt,
+ qe_port->bd_dma_addr);
+
+ ucc_slow_free(uccs);
+}
+
+/*
+ * Verify that the data in serial_struct is suitable for this device.
+ */
+static int qe_uart_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM)
+ return -EINVAL;
+
+ if (ser->irq < 0 || ser->irq >= NR_IRQS)
+ return -EINVAL;
+
+ if (ser->baud_base < 9600)
+ return -EINVAL;
+
+ return 0;
+}
+/* UART operations
+ *
+ * Details on these functions can be found in Documentation/serial/driver
+ */
+static struct uart_ops qe_uart_pops = {
+ .tx_empty = qe_uart_tx_empty,
+ .set_mctrl = qe_uart_set_mctrl,
+ .get_mctrl = qe_uart_get_mctrl,
+ .stop_tx = qe_uart_stop_tx,
+ .start_tx = qe_uart_start_tx,
+ .stop_rx = qe_uart_stop_rx,
+ .enable_ms = qe_uart_enable_ms,
+ .break_ctl = qe_uart_break_ctl,
+ .startup = qe_uart_startup,
+ .shutdown = qe_uart_shutdown,
+ .set_termios = qe_uart_set_termios,
+ .type = qe_uart_type,
+ .release_port = qe_uart_release_port,
+ .request_port = qe_uart_request_port,
+ .config_port = qe_uart_config_port,
+ .verify_port = qe_uart_verify_port,
+};
+
+/*
+ * Obtain the SOC model number and revision level
+ *
+ * This function parses the device tree to obtain the SOC model. It then
+ * reads the SVR register to the revision.
+ *
+ * The device tree stores the SOC model two different ways.
+ *
+ * The new way is:
+ *
+ * cpu@0 {
+ * compatible = "PowerPC,8323";
+ * device_type = "cpu";
+ * ...
+ *
+ *
+ * The old way is:
+ * PowerPC,8323@0 {
+ * device_type = "cpu";
+ * ...
+ *
+ * This code first checks the new way, and then the old way.
+ */
+static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l)
+{
+ struct device_node *np;
+ const char *soc_string;
+ unsigned int svr;
+ unsigned int soc;
+
+ /* Find the CPU node */
+ np = of_find_node_by_type(NULL, "cpu");
+ if (!np)
+ return 0;
+ /* Find the compatible property */
+ soc_string = of_get_property(np, "compatible", NULL);
+ if (!soc_string)
+ /* No compatible property, so try the name. */
+ soc_string = np->name;
+
+ /* Extract the SOC number from the "PowerPC," string */
+ if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc)
+ return 0;
+
+ /* Get the revision from the SVR */
+ svr = mfspr(SPRN_SVR);
+ *rev_h = (svr >> 4) & 0xf;
+ *rev_l = svr & 0xf;
+
+ return soc;
+}
+
+/*
+ * requst_firmware_nowait() callback function
+ *
+ * This function is called by the kernel when a firmware is made available,
+ * or if it times out waiting for the firmware.
+ */
+static void uart_firmware_cont(const struct firmware *fw, void *context)
+{
+ struct qe_firmware *firmware;
+ struct device *dev = context;
+ int ret;
+
+ if (!fw) {
+ dev_err(dev, "firmware not found\n");
+ return;
+ }
+
+ firmware = (struct qe_firmware *) fw->data;
+
+ if (firmware->header.length != fw->size) {
+ dev_err(dev, "invalid firmware\n");
+ return;
+ }
+
+ ret = qe_upload_firmware(firmware);
+ if (ret) {
+ dev_err(dev, "could not load firmware\n");
+ return;
+ }
+
+ firmware_loaded = 1;
+}
+
+static int ucc_uart_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct device_node *np = ofdev->node;
+ const unsigned int *iprop; /* Integer OF properties */
+ const char *sprop; /* String OF properties */
+ struct uart_qe_port *qe_port = NULL;
+ struct resource res;
+ int ret;
+
+ /*
+ * Determine if we need Soft-UART mode
+ */
+ if (of_find_property(np, "soft-uart", NULL)) {
+ dev_dbg(&ofdev->dev, "using Soft-UART mode\n");
+ soft_uart = 1;
+ }
+
+ /*
+ * If we are using Soft-UART, determine if we need to upload the
+ * firmware, too.
+ */
+ if (soft_uart) {
+ struct qe_firmware_info *qe_fw_info;
+
+ qe_fw_info = qe_get_firmware_info();
+
+ /* Check if the firmware has been uploaded. */
+ if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
+ firmware_loaded = 1;
+ } else {
+ char filename[32];
+ unsigned int soc;
+ unsigned int rev_h;
+ unsigned int rev_l;
+
+ soc = soc_info(&rev_h, &rev_l);
+ if (!soc) {
+ dev_err(&ofdev->dev, "unknown CPU model\n");
+ return -ENXIO;
+ }
+ sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
+ soc, rev_h, rev_l);
+
+ dev_info(&ofdev->dev, "waiting for firmware %s\n",
+ filename);
+
+ /*
+ * We call request_firmware_nowait instead of
+ * request_firmware so that the driver can load and
+ * initialize the ports without holding up the rest of
+ * the kernel. If hotplug support is enabled in the
+ * kernel, then we use it.
+ */
+ ret = request_firmware_nowait(THIS_MODULE,
+ FW_ACTION_HOTPLUG, filename, &ofdev->dev,
+ &ofdev->dev, uart_firmware_cont);
+ if (ret) {
+ dev_err(&ofdev->dev,
+ "could not load firmware %s\n",
+ filename);
+ return ret;
+ }
+ }
+ }
+
+ qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL);
+ if (!qe_port) {
+ dev_err(&ofdev->dev, "can't allocate QE port structure\n");
+ return -ENOMEM;
+ }
+
+ /* Search for IRQ and mapbase */
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret) {
+ dev_err(&ofdev->dev, "missing 'reg' property in device tree\n");
+ kfree(qe_port);
+ return ret;
+ }
+ if (!res.start) {
+ dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+ qe_port->port.mapbase = res.start;
+
+ /* Get the UCC number (device ID) */
+ /* UCCs are numbered 1-7 */
+ iprop = of_get_property(np, "device-id", NULL);
+ if (!iprop || (*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
+ dev_err(&ofdev->dev,
+ "missing or invalid UCC specified in device tree\n");
+ kfree(qe_port);
+ return -ENODEV;
+ }
+ qe_port->ucc_num = *iprop - 1;
+
+ /*
+ * In the future, we should not require the BRG to be specified in the
+ * device tree. If no clock-source is specified, then just pick a BRG
+ * to use. This requires a new QE library function that manages BRG
+ * assignments.
+ */
+
+ sprop = of_get_property(np, "rx-clock-name", NULL);
+ if (!sprop) {
+ dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n");
+ kfree(qe_port);
+ return -ENODEV;
+ }
+
+ qe_port->us_info.rx_clock = qe_clock_source(sprop);
+ if ((qe_port->us_info.rx_clock < QE_BRG1) ||
+ (qe_port->us_info.rx_clock > QE_BRG16)) {
+ dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n");
+ kfree(qe_port);
+ return -ENODEV;
+ }
+
+#ifdef LOOPBACK
+ /* In internal loopback mode, TX and RX must use the same clock */
+ qe_port->us_info.tx_clock = qe_port->us_info.rx_clock;
+#else
+ sprop = of_get_property(np, "tx-clock-name", NULL);
+ if (!sprop) {
+ dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n");
+ kfree(qe_port);
+ return -ENODEV;
+ }
+ qe_port->us_info.tx_clock = qe_clock_source(sprop);
+#endif
+ if ((qe_port->us_info.tx_clock < QE_BRG1) ||
+ (qe_port->us_info.tx_clock > QE_BRG16)) {
+ dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n");
+ kfree(qe_port);
+ return -ENODEV;
+ }
+
+ /* Get the port number, numbered 0-3 */
+ iprop = of_get_property(np, "port-number", NULL);
+ if (!iprop) {
+ dev_err(&ofdev->dev, "missing port-number in device tree\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+ qe_port->port.line = *iprop;
+ if (qe_port->port.line >= UCC_MAX_UART) {
+ dev_err(&ofdev->dev, "port-number must be 0-%u\n",
+ UCC_MAX_UART - 1);
+ kfree(qe_port);
+ return -EINVAL;
+ }
+
+ qe_port->port.irq = irq_of_parse_and_map(np, 0);
+ if (qe_port->port.irq == NO_IRQ) {
+ dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n",
+ qe_port->ucc_num + 1);
+ kfree(qe_port);
+ return -EINVAL;
+ }
+
+ /*
+ * Newer device trees have an "fsl,qe" compatible property for the QE
+ * node, but we still need to support older device trees.
+ */
+ np = of_find_compatible_node(NULL, NULL, "fsl,qe");
+ if (!np) {
+ np = of_find_node_by_type(NULL, "qe");
+ if (!np) {
+ dev_err(&ofdev->dev, "could not find 'qe' node\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+ }
+
+ iprop = of_get_property(np, "brg-frequency", NULL);
+ if (!iprop) {
+ dev_err(&ofdev->dev,
+ "missing brg-frequency in device tree\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+
+ if (*iprop)
+ qe_port->port.uartclk = *iprop;
+ else {
+ /*
+ * Older versions of U-Boot do not initialize the brg-frequency
+ * property, so in this case we assume the BRG frequency is
+ * half the QE bus frequency.
+ */
+ iprop = of_get_property(np, "bus-frequency", NULL);
+ if (!iprop) {
+ dev_err(&ofdev->dev,
+ "missing QE bus-frequency in device tree\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+ if (*iprop)
+ qe_port->port.uartclk = *iprop / 2;
+ else {
+ dev_err(&ofdev->dev,
+ "invalid QE bus-frequency in device tree\n");
+ kfree(qe_port);
+ return -EINVAL;
+ }
+ }
+
+ spin_lock_init(&qe_port->port.lock);
+ qe_port->np = np;
+ qe_port->port.dev = &ofdev->dev;
+ qe_port->port.ops = &qe_uart_pops;
+ qe_port->port.iotype = UPIO_MEM;
+
+ qe_port->tx_nrfifos = TX_NUM_FIFO;
+ qe_port->tx_fifosize = TX_BUF_SIZE;
+ qe_port->rx_nrfifos = RX_NUM_FIFO;
+ qe_port->rx_fifosize = RX_BUF_SIZE;
+
+ qe_port->wait_closing = UCC_WAIT_CLOSING;
+ qe_port->port.fifosize = 512;
+ qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+
+ qe_port->us_info.ucc_num = qe_port->ucc_num;
+ qe_port->us_info.regs = (phys_addr_t) res.start;
+ qe_port->us_info.irq = qe_port->port.irq;
+
+ qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos;
+ qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos;
+
+ /* Make sure ucc_slow_init() initializes both TX and RX */
+ qe_port->us_info.init_tx = 1;
+ qe_port->us_info.init_rx = 1;
+
+ /* Add the port to the uart sub-system. This will cause
+ * qe_uart_config_port() to be called, so the us_info structure must
+ * be initialized.
+ */
+ ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port);
+ if (ret) {
+ dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n",
+ qe_port->port.line);
+ kfree(qe_port);
+ return ret;
+ }
+
+ dev_set_drvdata(&ofdev->dev, qe_port);
+
+ dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n",
+ qe_port->ucc_num + 1, qe_port->port.line);
+
+ /* Display the mknod command for this device */
+ dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n",
+ qe_port->port.line, SERIAL_QE_MAJOR,
+ SERIAL_QE_MINOR + qe_port->port.line);
+
+ return 0;
+}
+
+static int ucc_uart_remove(struct of_device *ofdev)
+{
+ struct uart_qe_port *qe_port = dev_get_drvdata(&ofdev->dev);
+
+ dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line);
+
+ uart_remove_one_port(&ucc_uart_driver, &qe_port->port);
+
+ dev_set_drvdata(&ofdev->dev, NULL);
+ kfree(qe_port);
+
+ return 0;
+}
+
+static struct of_device_id ucc_uart_match[] = {
+ {
+ .type = "serial",
+ .compatible = "ucc_uart",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ucc_uart_match);
+
+static struct of_platform_driver ucc_uart_of_driver = {
+ .owner = THIS_MODULE,
+ .name = "ucc_uart",
+ .match_table = ucc_uart_match,
+ .probe = ucc_uart_probe,
+ .remove = ucc_uart_remove,
+};
+
+static int __init ucc_uart_init(void)
+{
+ int ret;
+
+ printk(KERN_INFO "Freescale QUICC Engine UART device driver\n");
+#ifdef LOOPBACK
+ printk(KERN_INFO "ucc-uart: Using loopback mode\n");
+#endif
+
+ ret = uart_register_driver(&ucc_uart_driver);
+ if (ret) {
+ printk(KERN_ERR "ucc-uart: could not register UART driver\n");
+ return ret;
+ }
+
+ ret = of_register_platform_driver(&ucc_uart_of_driver);
+ if (ret)
+ printk(KERN_ERR
+ "ucc-uart: could not register platform driver\n");
+
+ return ret;
+}
+
+static void __exit ucc_uart_exit(void)
+{
+ printk(KERN_INFO
+ "Freescale QUICC Engine UART device driver unloading\n");
+
+ of_unregister_platform_driver(&ucc_uart_of_driver);
+ uart_unregister_driver(&ucc_uart_driver);
+}
+
+module_init(ucc_uart_init);
+module_exit(ucc_uart_exit);
+
+MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART");
+MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR);
+
diff --git a/include/asm-powerpc/immap_qe.h b/include/asm-powerpc/immap_qe.h
index aba9806..82a4526 100644
--- a/include/asm-powerpc/immap_qe.h
+++ b/include/asm-powerpc/immap_qe.h
@@ -393,9 +393,39 @@
u8 res2[0x48];
} __attribute__ ((packed));
-/* RISC Special Registers (Trap and Breakpoint) */
+/*
+ * RISC Special Registers (Trap and Breakpoint). These are described in
+ * the QE Developer's Handbook.
+ */
struct rsp {
- u32 reg[0x40]; /* 64 32-bit registers */
+ __be32 tibcr[16]; /* Trap/instruction breakpoint control regs */
+ u8 res0[64];
+ __be32 ibcr0;
+ __be32 ibs0;
+ __be32 ibcnr0;
+ u8 res1[4];
+ __be32 ibcr1;
+ __be32 ibs1;
+ __be32 ibcnr1;
+ __be32 npcr;
+ __be32 dbcr;
+ __be32 dbar;
+ __be32 dbamr;
+ __be32 dbsr;
+ __be32 dbcnr;
+ u8 res2[12];
+ __be32 dbdr_h;
+ __be32 dbdr_l;
+ __be32 dbdmr_h;
+ __be32 dbdmr_l;
+ __be32 bsr;
+ __be32 bor;
+ __be32 bior;
+ u8 res3[4];
+ __be32 iatr[4];
+ __be32 eccr; /* Exception control configuration register */
+ __be32 eicr;
+ u8 res4[0x100-0xf8];
} __attribute__ ((packed));
struct qe_immap {
diff --git a/include/asm-powerpc/lmb.h b/include/asm-powerpc/lmb.h
index b5f9f4c..5d1dc48 100644
--- a/include/asm-powerpc/lmb.h
+++ b/include/asm-powerpc/lmb.h
@@ -51,6 +51,7 @@
extern unsigned long __init lmb_phys_mem_size(void);
extern unsigned long __init lmb_end_of_DRAM(void);
extern void __init lmb_enforce_memory_limit(unsigned long memory_limit);
+extern int __init lmb_is_reserved(unsigned long addr);
extern void lmb_dump_all(void);
diff --git a/include/asm-powerpc/mpc8260.h b/include/asm-powerpc/mpc8260.h
index e0d4807..03317e1 100644
--- a/include/asm-powerpc/mpc8260.h
+++ b/include/asm-powerpc/mpc8260.h
@@ -8,6 +8,7 @@
#ifndef __ASM_POWERPC_MPC8260_H__
#define __ASM_POWERPC_MPC8260_H__
+#define MPC82XX_BCR_PLDP 0x00800000 /* Pipeline Maximum Depth */
#ifdef CONFIG_8260
diff --git a/include/asm-powerpc/pci-bridge.h b/include/asm-powerpc/pci-bridge.h
index a6ea49e..e5802c6 100644
--- a/include/asm-powerpc/pci-bridge.h
+++ b/include/asm-powerpc/pci-bridge.h
@@ -152,9 +152,6 @@
resource_size_t cfg_addr,
resource_size_t cfg_data, u32 flags);
extern void setup_grackle(struct pci_controller *hose);
-extern void __init update_bridge_resource(struct pci_dev *dev,
- struct resource *res);
-
#else /* CONFIG_PPC64 */
/*
diff --git a/include/asm-powerpc/qe.h b/include/asm-powerpc/qe.h
index a24b7b1..430dc77 100644
--- a/include/asm-powerpc/qe.h
+++ b/include/asm-powerpc/qe.h
@@ -94,6 +94,58 @@
void qe_muram_dump(void);
void *qe_muram_addr(unsigned long offset);
+/* Structure that defines QE firmware binary files.
+ *
+ * See Documentation/powerpc/qe-firmware.txt for a description of these
+ * fields.
+ */
+struct qe_firmware {
+ struct qe_header {
+ __be32 length; /* Length of the entire structure, in bytes */
+ u8 magic[3]; /* Set to { 'Q', 'E', 'F' } */
+ u8 version; /* Version of this layout. First ver is '1' */
+ } header;
+ u8 id[62]; /* Null-terminated identifier string */
+ u8 split; /* 0 = shared I-RAM, 1 = split I-RAM */
+ u8 count; /* Number of microcode[] structures */
+ struct {
+ __be16 model; /* The SOC model */
+ u8 major; /* The SOC revision major */
+ u8 minor; /* The SOC revision minor */
+ } __attribute__ ((packed)) soc;
+ u8 padding[4]; /* Reserved, for alignment */
+ __be64 extended_modes; /* Extended modes */
+ __be32 vtraps[8]; /* Virtual trap addresses */
+ u8 reserved[4]; /* Reserved, for future expansion */
+ struct qe_microcode {
+ u8 id[32]; /* Null-terminated identifier */
+ __be32 traps[16]; /* Trap addresses, 0 == ignore */
+ __be32 eccr; /* The value for the ECCR register */
+ __be32 iram_offset; /* Offset into I-RAM for the code */
+ __be32 count; /* Number of 32-bit words of the code */
+ __be32 code_offset; /* Offset of the actual microcode */
+ u8 major; /* The microcode version major */
+ u8 minor; /* The microcode version minor */
+ u8 revision; /* The microcode version revision */
+ u8 padding; /* Reserved, for alignment */
+ u8 reserved[4]; /* Reserved, for future expansion */
+ } __attribute__ ((packed)) microcode[1];
+ /* All microcode binaries should be located here */
+ /* CRC32 should be located here, after the microcode binaries */
+} __attribute__ ((packed));
+
+struct qe_firmware_info {
+ char id[64]; /* Firmware name */
+ u32 vtraps[8]; /* Virtual trap addresses */
+ u64 extended_modes; /* Extended modes */
+};
+
+/* Upload a firmware to the QE */
+int qe_upload_firmware(const struct qe_firmware *firmware);
+
+/* Obtain information on the uploaded firmware */
+struct qe_firmware_info *qe_get_firmware_info(void);
+
/* Buffer descriptors */
struct qe_bd {
__be16 status;
@@ -329,6 +381,15 @@
#define QE_SDEBCR_BA_MASK 0x01FFFFFF
+/* Communication Processor */
+#define QE_CP_CERCR_MEE 0x8000 /* Multi-user RAM ECC enable */
+#define QE_CP_CERCR_IEE 0x4000 /* Instruction RAM ECC enable */
+#define QE_CP_CERCR_CIR 0x0800 /* Common instruction RAM */
+
+/* I-RAM */
+#define QE_IRAM_IADD_AIE 0x80000000 /* Auto Increment Enable */
+#define QE_IRAM_IADD_BADDR 0x00080000 /* Base Address */
+
/* UPC */
#define UPGCR_PROTOCOL 0x80000000 /* protocol ul2 or pl2 */
#define UPGCR_TMS 0x40000000 /* Transmit master/slave mode */
diff --git a/include/asm-powerpc/system.h b/include/asm-powerpc/system.h
index 87be8c3..bc9739d 100644
--- a/include/asm-powerpc/system.h
+++ b/include/asm-powerpc/system.h
@@ -169,6 +169,8 @@
extern void bad_page_fault(struct pt_regs *, unsigned long, int);
extern int die(const char *, struct pt_regs *, long);
extern void _exception(int, struct pt_regs *, int, unsigned long);
+extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
+
#ifdef CONFIG_BOOKE_WDT
extern u32 booke_wdt_enabled;
extern u32 booke_wdt_period;
diff --git a/include/linux/phy_fixed.h b/include/linux/phy_fixed.h
index 04ba70d..509d8f5 100644
--- a/include/linux/phy_fixed.h
+++ b/include/linux/phy_fixed.h
@@ -1,38 +1,31 @@
#ifndef __PHY_FIXED_H
#define __PHY_FIXED_H
-#define MII_REGS_NUM 29
-
-/* max number of virtual phy stuff */
-#define MAX_PHY_AMNT 10
-/*
- The idea is to emulate normal phy behavior by responding with
- pre-defined values to mii BMCR read, so that read_status hook could
- take all the needed info.
-*/
-
struct fixed_phy_status {
- u8 link;
- u16 speed;
- u8 duplex;
+ int link;
+ int speed;
+ int duplex;
+ int pause;
+ int asym_pause;
};
-/*-----------------------------------------------------------------------------
- * Private information hoder for mii_bus
- *-----------------------------------------------------------------------------*/
-struct fixed_info {
- u16 *regs;
- u8 regs_num;
- struct fixed_phy_status phy_status;
- struct phy_device *phydev; /* pointer to the container */
- /* link & speed cb */
- int (*link_update) (struct net_device *, struct fixed_phy_status *);
+#ifdef CONFIG_FIXED_PHY
+extern int fixed_phy_add(unsigned int irq, int phy_id,
+ struct fixed_phy_status *status);
+#else
+static inline int fixed_phy_add(unsigned int irq, int phy_id,
+ struct fixed_phy_status *status)
+{
+ return -ENODEV;
+}
+#endif /* CONFIG_FIXED_PHY */
-};
-
-
-int fixed_mdio_set_link_update(struct phy_device *,
- int (*link_update) (struct net_device *, struct fixed_phy_status *));
-struct fixed_info *fixed_mdio_get_phydev (int phydev_ind);
+/*
+ * This function issued only by fixed_phy-aware drivers, no need
+ * protect it with #ifdef
+ */
+extern int fixed_phy_set_link_update(struct phy_device *phydev,
+ int (*link_update)(struct net_device *,
+ struct fixed_phy_status *));
#endif /* __PHY_FIXED_H */
