[PATCH] sky2: fiber support
Fix the support for fiber connected gigabit boards.
Allow half duplex gigabit to be configured.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index a3a4ab2..2b9272c 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -308,7 +308,7 @@
}
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
if (hw->chip_id == CHIP_ID_YUKON_FE) {
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
@@ -325,25 +325,37 @@
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
}
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
} else {
/* workaround for deviation #4.88 (CRC errors) */
/* disable Automatic Crossover */
ctrl &= ~PHY_M_PC_MDIX_MSK;
+ }
+
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ /* special setup for PHY 88E1112 Fiber */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && !sky2_is_copper(hw)) {
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+
+ /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl &= ~PHY_M_MAC_MD_MSK;
+ ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
- if (hw->chip_id == CHIP_ID_YUKON_XL) {
- /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
- ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
- ctrl &= ~PHY_M_MAC_MD_MSK;
- ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
-
+ if (hw->pmd_type == 'P') {
/* select page 1 to access Fiber registers */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
+
+ /* for SFP-module set SIGDET polarity to low */
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl |= PHY_M_FIB_SIGD_POL;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
}
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
@@ -361,7 +373,7 @@
reg = 0;
if (sky2->autoneg == AUTONEG_ENABLE) {
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
if (sky2->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
@@ -374,8 +386,12 @@
adv |= PHY_M_AN_10_FD;
if (sky2->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
- } else /* special defines for FIBER (88E1011S only) */
- adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+ } else { /* special defines for FIBER (88E1040S only) */
+ if (sky2->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_M_AN_1000X_AFD;
+ if (sky2->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_M_AN_1000X_AHD;
+ }
/* Set Flow-control capabilities */
if (sky2->tx_pause && sky2->rx_pause)
@@ -1496,7 +1512,7 @@
static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
{
- if (!hw->copper)
+ if (!sky2_is_copper(hw))
return SPEED_1000;
if (hw->chip_id == CHIP_ID_YUKON_FE)
@@ -2269,7 +2285,7 @@
static int sky2_reset(struct sky2_hw *hw)
{
u16 status;
- u8 t8, pmd_type;
+ u8 t8;
int i;
sky2_write8(hw, B0_CTST, CS_RST_CLR);
@@ -2315,9 +2331,7 @@
sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
- pmd_type = sky2_read8(hw, B2_PMD_TYP);
- hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
-
+ hw->pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
@@ -2414,21 +2428,22 @@
static u32 sky2_supported_modes(const struct sky2_hw *hw)
{
- u32 modes;
- if (hw->copper) {
- modes = SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg | SUPPORTED_TP;
+ if (sky2_is_copper(hw)) {
+ u32 modes = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
if (hw->chip_id != CHIP_ID_YUKON_FE)
modes |= SUPPORTED_1000baseT_Half
- | SUPPORTED_1000baseT_Full;
+ | SUPPORTED_1000baseT_Full;
+ return modes;
} else
- modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
- | SUPPORTED_Autoneg;
- return modes;
+ return SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg
+ | SUPPORTED_FIBRE;
}
static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
@@ -2439,7 +2454,7 @@
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = sky2_supported_modes(hw);
ecmd->phy_address = PHY_ADDR_MARV;
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
ecmd->supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
@@ -2448,12 +2463,14 @@
| SUPPORTED_1000baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
ecmd->port = PORT_TP;
- } else
+ ecmd->speed = sky2->speed;
+ } else {
+ ecmd->speed = SPEED_1000;
ecmd->port = PORT_FIBRE;
+ }
ecmd->advertising = sky2->advertising;
ecmd->autoneg = sky2->autoneg;
- ecmd->speed = sky2->speed;
ecmd->duplex = sky2->duplex;
return 0;
}
