Merge branch 'next-i2c-mpc-v8' into next-i2c
diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
index b6d2e21..50da203 100644
--- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
@@ -2,15 +2,14 @@
Required properties :
- - device_type : Should be "i2c"
- reg : Offset and length of the register set for the device
+ - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
+ compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
+ mpc5200 or mpc5200b. For the mpc5121, an additional node
+ "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
Recommended properties :
- - compatible : compatibility list with 2 entries, the first should
- be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor,
- e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one
- should be "fsl-i2c".
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
@@ -24,25 +23,40 @@
Examples :
+ /* MPC5121 based board */
+ i2c@1740 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+ reg = <0x1740 0x20>;
+ interrupts = <11 0x8>;
+ interrupt-parent = <&ipic>;
+ clock-frequency = <100000>;
+ };
+
+ i2ccontrol@1760 {
+ compatible = "fsl,mpc5121-i2c-ctrl";
+ reg = <0x1760 0x8>;
+ };
+
+ /* MPC5200B based board */
i2c@3d00 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <0>;
reg = <0x3d00 0x40>;
interrupts = <2 15 0>;
interrupt-parent = <&mpc5200_pic>;
fsl,preserve-clocking;
};
+ /* MPC8544 base board */
i2c@3100 {
#address-cells = <1>;
#size-cells = <0>;
- cell-index = <1>;
compatible = "fsl,mpc8544-i2c", "fsl-i2c";
reg = <0x3100 0x100>;
interrupts = <43 2>;
interrupt-parent = <&mpic>;
clock-frequency = <400000>;
};
-
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 1004181..ecf079b 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -419,13 +419,12 @@
instead.
config I2C_MPC
- tristate "MPC107/824x/85xx/52xx/86xx"
+ tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx"
depends on PPC32
help
If you say yes to this option, support will be included for the
- built-in I2C interface on the MPC107/Tsi107/MPC8240/MPC8245 and
- MPC85xx/MPC8641 family processors. The driver may also work on 52xx
- family processors, though interrupts are known not to work.
+ built-in I2C interface on the MPC107, Tsi107, MPC512x, MPC52xx,
+ MPC8240, MPC8245, MPC83xx, MPC85xx and MPC8641 family processors.
This driver can also be built as a module. If so, the module
will be called i2c-mpc.
diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c
index f627001..78a15af 100644
--- a/drivers/i2c/busses/i2c-mpc.c
+++ b/drivers/i2c/busses/i2c-mpc.c
@@ -31,6 +31,9 @@
#define DRV_NAME "mpc-i2c"
+#define MPC_I2C_CLOCK_LEGACY 0
+#define MPC_I2C_CLOCK_PRESERVE (~0U)
+
#define MPC_I2C_FDR 0x04
#define MPC_I2C_CR 0x08
#define MPC_I2C_SR 0x0c
@@ -66,10 +69,9 @@
u16 fdr; /* including dfsrr */
};
-struct mpc_i2c_match_data {
- void (*setclock)(struct device_node *node,
- struct mpc_i2c *i2c,
- u32 clock, u32 prescaler);
+struct mpc_i2c_data {
+ void (*setup)(struct device_node *node, struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler);
u32 prescaler;
};
@@ -164,8 +166,8 @@
return 0;
}
-#ifdef CONFIG_PPC_MPC52xx
-static const struct mpc_i2c_divider mpc_i2c_dividers_52xx[] = {
+#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_PPC_MPC512x)
+static const struct mpc_i2c_divider mpc_i2c_dividers_52xx[] __devinitconst = {
{20, 0x20}, {22, 0x21}, {24, 0x22}, {26, 0x23},
{28, 0x24}, {30, 0x01}, {32, 0x25}, {34, 0x02},
{36, 0x26}, {40, 0x27}, {44, 0x04}, {48, 0x28},
@@ -186,14 +188,15 @@
{10240, 0x9d}, {12288, 0x9e}, {15360, 0x9f}
};
-int mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, int prescaler)
+static int __devinit mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock,
+ int prescaler)
{
const struct mpc_i2c_divider *div = NULL;
unsigned int pvr = mfspr(SPRN_PVR);
u32 divider;
int i;
- if (!clock)
+ if (clock == MPC_I2C_CLOCK_LEGACY)
return -EINVAL;
/* Determine divider value */
@@ -215,12 +218,18 @@
return div ? (int)div->fdr : -EINVAL;
}
-static void mpc_i2c_setclock_52xx(struct device_node *node,
- struct mpc_i2c *i2c,
- u32 clock, u32 prescaler)
+static void __devinit mpc_i2c_setup_52xx(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
{
int ret, fdr;
+ if (clock == MPC_I2C_CLOCK_PRESERVE) {
+ dev_dbg(i2c->dev, "using fdr %d\n",
+ readb(i2c->base + MPC_I2C_FDR));
+ return;
+ }
+
ret = mpc_i2c_get_fdr_52xx(node, clock, prescaler);
fdr = (ret >= 0) ? ret : 0x3f; /* backward compatibility */
@@ -229,16 +238,52 @@
if (ret >= 0)
dev_info(i2c->dev, "clock %d Hz (fdr=%d)\n", clock, fdr);
}
-#else /* !CONFIG_PPC_MPC52xx */
-static void mpc_i2c_setclock_52xx(struct device_node *node,
- struct mpc_i2c *i2c,
- u32 clock, u32 prescaler)
+#else /* !(CONFIG_PPC_MPC52xx || CONFIG_PPC_MPC512x) */
+static void __devinit mpc_i2c_setup_52xx(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
{
}
-#endif /* CONFIG_PPC_MPC52xx*/
+#endif /* CONFIG_PPC_MPC52xx || CONFIG_PPC_MPC512x */
+
+#ifdef CONFIG_PPC_MPC512x
+static void __devinit mpc_i2c_setup_512x(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
+{
+ struct device_node *node_ctrl;
+ void __iomem *ctrl;
+ const u32 *pval;
+ u32 idx;
+
+ /* Enable I2C interrupts for mpc5121 */
+ node_ctrl = of_find_compatible_node(NULL, NULL,
+ "fsl,mpc5121-i2c-ctrl");
+ if (node_ctrl) {
+ ctrl = of_iomap(node_ctrl, 0);
+ if (ctrl) {
+ /* Interrupt enable bits for i2c-0/1/2: bit 24/26/28 */
+ pval = of_get_property(node, "reg", NULL);
+ idx = (*pval & 0xff) / 0x20;
+ setbits32(ctrl, 1 << (24 + idx * 2));
+ iounmap(ctrl);
+ }
+ of_node_put(node_ctrl);
+ }
+
+ /* The clock setup for the 52xx works also fine for the 512x */
+ mpc_i2c_setup_52xx(node, i2c, clock, prescaler);
+}
+#else /* CONFIG_PPC_MPC512x */
+static void __devinit mpc_i2c_setup_512x(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
+{
+}
+#endif /* CONFIG_PPC_MPC512x */
#ifdef CONFIG_FSL_SOC
-static const struct mpc_i2c_divider mpc_i2c_dividers_8xxx[] = {
+static const struct mpc_i2c_divider mpc_i2c_dividers_8xxx[] __devinitconst = {
{160, 0x0120}, {192, 0x0121}, {224, 0x0122}, {256, 0x0123},
{288, 0x0100}, {320, 0x0101}, {352, 0x0601}, {384, 0x0102},
{416, 0x0602}, {448, 0x0126}, {480, 0x0103}, {512, 0x0127},
@@ -258,7 +303,7 @@
{49152, 0x011e}, {61440, 0x011f}
};
-u32 mpc_i2c_get_sec_cfg_8xxx(void)
+static u32 __devinit mpc_i2c_get_sec_cfg_8xxx(void)
{
struct device_node *node = NULL;
u32 __iomem *reg;
@@ -287,13 +332,14 @@
return val;
}
-int mpc_i2c_get_fdr_8xxx(struct device_node *node, u32 clock, u32 prescaler)
+static int __devinit mpc_i2c_get_fdr_8xxx(struct device_node *node, u32 clock,
+ u32 prescaler)
{
const struct mpc_i2c_divider *div = NULL;
u32 divider;
int i;
- if (!clock)
+ if (clock == MPC_I2C_CLOCK_LEGACY)
return -EINVAL;
/* Determine proper divider value */
@@ -320,12 +366,19 @@
return div ? (int)div->fdr : -EINVAL;
}
-static void mpc_i2c_setclock_8xxx(struct device_node *node,
- struct mpc_i2c *i2c,
- u32 clock, u32 prescaler)
+static void __devinit mpc_i2c_setup_8xxx(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
{
int ret, fdr;
+ if (clock == MPC_I2C_CLOCK_PRESERVE) {
+ dev_dbg(i2c->dev, "using dfsrr %d, fdr %d\n",
+ readb(i2c->base + MPC_I2C_DFSRR),
+ readb(i2c->base + MPC_I2C_FDR));
+ return;
+ }
+
ret = mpc_i2c_get_fdr_8xxx(node, clock, prescaler);
fdr = (ret >= 0) ? ret : 0x1031; /* backward compatibility */
@@ -338,9 +391,9 @@
}
#else /* !CONFIG_FSL_SOC */
-static void mpc_i2c_setclock_8xxx(struct device_node *node,
- struct mpc_i2c *i2c,
- u32 clock, u32 prescaler)
+static void __devinit mpc_i2c_setup_8xxx(struct device_node *node,
+ struct mpc_i2c *i2c,
+ u32 clock, u32 prescaler)
{
}
#endif /* CONFIG_FSL_SOC */
@@ -494,7 +547,7 @@
{
struct mpc_i2c *i2c;
const u32 *prop;
- u32 clock = 0;
+ u32 clock = MPC_I2C_CLOCK_LEGACY;
int result = 0;
int plen;
@@ -523,21 +576,21 @@
}
}
- if (!of_get_property(op->node, "fsl,preserve-clocking", NULL)) {
+ if (of_get_property(op->node, "fsl,preserve-clocking", NULL)) {
+ clock = MPC_I2C_CLOCK_PRESERVE;
+ } else {
prop = of_get_property(op->node, "clock-frequency", &plen);
if (prop && plen == sizeof(u32))
clock = *prop;
+ }
- if (match->data) {
- struct mpc_i2c_match_data *data =
- (struct mpc_i2c_match_data *)match->data;
- data->setclock(op->node, i2c, clock, data->prescaler);
- } else {
- /* Backwards compatibility */
- if (of_get_property(op->node, "dfsrr", NULL))
- mpc_i2c_setclock_8xxx(op->node, i2c,
- clock, 0);
- }
+ if (match->data) {
+ struct mpc_i2c_data *data = match->data;
+ data->setup(op->node, i2c, clock, data->prescaler);
+ } else {
+ /* Backwards compatibility */
+ if (of_get_property(op->node, "dfsrr", NULL))
+ mpc_i2c_setup_8xxx(op->node, i2c, clock, 0);
}
dev_set_drvdata(&op->dev, i2c);
@@ -582,47 +635,42 @@
return 0;
};
+static struct mpc_i2c_data mpc_i2c_data_512x __devinitdata = {
+ .setup = mpc_i2c_setup_512x,
+};
+
+static struct mpc_i2c_data mpc_i2c_data_52xx __devinitdata = {
+ .setup = mpc_i2c_setup_52xx,
+};
+
+static struct mpc_i2c_data mpc_i2c_data_8313 __devinitdata = {
+ .setup = mpc_i2c_setup_8xxx,
+};
+
+static struct mpc_i2c_data mpc_i2c_data_8543 __devinitdata = {
+ .setup = mpc_i2c_setup_8xxx,
+ .prescaler = 2,
+};
+
+static struct mpc_i2c_data mpc_i2c_data_8544 __devinitdata = {
+ .setup = mpc_i2c_setup_8xxx,
+ .prescaler = 3,
+};
+
static const struct of_device_id mpc_i2c_of_match[] = {
- {.compatible = "mpc5200-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_52xx,
- },
- },
- {.compatible = "fsl,mpc5200b-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_52xx,
- },
- },
- {.compatible = "fsl,mpc5200-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_52xx,
- },
- },
- {.compatible = "fsl,mpc8313-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_8xxx,
- },
- },
- {.compatible = "fsl,mpc8543-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_8xxx,
- .prescaler = 2,
- },
- },
- {.compatible = "fsl,mpc8544-i2c",
- .data = &(struct mpc_i2c_match_data) {
- .setclock = mpc_i2c_setclock_8xxx,
- .prescaler = 3,
- },
+ {.compatible = "mpc5200-i2c", .data = &mpc_i2c_data_52xx, },
+ {.compatible = "fsl,mpc5200b-i2c", .data = &mpc_i2c_data_52xx, },
+ {.compatible = "fsl,mpc5200-i2c", .data = &mpc_i2c_data_52xx, },
+ {.compatible = "fsl,mpc5121-i2c", .data = &mpc_i2c_data_512x, },
+ {.compatible = "fsl,mpc8313-i2c", .data = &mpc_i2c_data_8313, },
+ {.compatible = "fsl,mpc8543-i2c", .data = &mpc_i2c_data_8543, },
+ {.compatible = "fsl,mpc8544-i2c", .data = &mpc_i2c_data_8544, },
/* Backward compatibility */
- },
{.compatible = "fsl-i2c", },
{},
};
-
MODULE_DEVICE_TABLE(of, mpc_i2c_of_match);
-
/* Structure for a device driver */
static struct of_platform_driver mpc_i2c_driver = {
.match_table = mpc_i2c_of_match,
@@ -655,5 +703,5 @@
MODULE_AUTHOR("Adrian Cox <adrian@humboldt.co.uk>");
MODULE_DESCRIPTION("I2C-Bus adapter for MPC107 bridge and "
- "MPC824x/85xx/52xx processors");
+ "MPC824x/83xx/85xx/86xx/512x/52xx processors");
MODULE_LICENSE("GPL");
